AK5367AEF - 24-Bit Stereo ADC, 96 kHz | AKM
MPN: AK5367AEF ✗ اختتامِ زندگیAK5367AEF جائزہ
An ADC is an analog-to-digital converter, a data-conversion IC that samples continuous analog audio voltages and converts them into proportional digital values. The AK5367A belongs to the ADC and DAC hierarchy within data-conversion ICs, where it serves as the bridge between analog microphone or line-level audio and a digital audio processor. Its stereo architecture processes two audio channels while its I2C control interface allows a host controller to configure operating conditions and read device status.
The primary specifications are 24-bit resolution, a 32 kHz to 96 kHz sampling-rate range, and a 3 V to 3.6 V analog and digital operating range. The converter is intended for consumer audio and digital-recording applications where a compact surface-mount implementation, stereo capture, and high-resolution conversion are important. Its documented operating-temperature ordering option covers -20 °C to +85 °C.
The AK5367A provides separate analog and digital supply pins, supporting careful partitioning of analog signal paths and digital interfaces on a mixed-signal PCB. An I2C control path and I/O-oriented clock pins provide integration with audio codecs, digital signal processors, and embedded audio systems. The device also supports power-down control, allowing its digital filter to be reset when the power-down pin is asserted low.
Typical uses include digital microphones, USB or portable audio equipment, consumer recording systems, audio capture accessories, and stereo line-input converters. The 24-bit format supports high-resolution audio workflows, while the 96 kHz maximum sampling rate supports 48 kHz and 96 kHz digital-audio streams. The compact 30-pin VSOP with 0.65 mm pitch is suited to space-constrained boards requiring fine-pitch assembly.
Layout is critical because analog and digital supplies must be decoupled close to their corresponding pins, and high-speed signals require short controlled routes. Confirm the pin-description table in the manufacturer datasheet before assigning tracks or selecting the system clock. The PDN control net should be sequenced so that the required reset action follows power-up.
This product page organizes the documented AK5367AEF characteristics, package information, interface considerations, and practical application guidance. It also distinguishes verified drop-in replacements from merely similar converters, helping PCB designers avoid substitutions that differ in footprint, pin assignment, or audio interface behavior.
کے لیے ڈراپ اِن متبادل AK5367AEF — یکساں پیکیج، پن سے پن مطابقت پذیر۔ مختلف پیکیج والے پرزے جن کے لیے PCB دوبارہ کام درکار ہو، شامل نہیں ہیں۔
اس سیریز میں مختلف ورژن
اسی سیریز کے ماڈلز جو ڈراپ اِن مطابقت رکھتے ہیں AK5367AEF (یکساں فارم فیکٹر اور فٹ پرنٹ) — میں مختلف Converter Type, Package.
اس پروڈکٹ کے لیے کوئی ڈراپ اِن متبادل دستیاب نہیں۔
متبادل کی درخواست کریںAK5367AEF زیادہ سے زیادہ ریٹنگز اور برقی خصوصیات
| Converter Type | Stereo ADC |
| ریزولوشن | 24 bit |
| سیمپلنگ ریٹ | 32 kHz to 96 kHz |
| Analog Supply Voltage | 3 V to 3.6 V |
| Digital Supply Voltage | 3 V to 3.6 V |
| انٹرفیس | I2C |
| پیکیج | 30-pin VSOP |
| Package Pitch | 0.65 mm |
| ماؤنٹنگ ٹائپ | Surface mount |
| آپریٹنگ درجہ حرارت | -20 °C to +85 °C |
| Audio Channel Count | 2 channels |
| Power-Down Control | PDN pin active low |
| Digital Filter Reset | Executed with power-down assertion |
| Clock Interface | LRCK and BICK clock pins |
| Recommended Application | Consumer audio and digital recording |
| Evaluation Board | AKD5367 |
| Order Code Temperature Range | -20 °C to +85 °C |
AK5367AEF 0.65 mm پن کنفیگریشن گائیڈ
AK5367AEF (0.65 mm پیکیج) کے لیے پن کنفیگریشن۔ اس اینالاگ کمپوننٹ میں اِن پٹ، آؤٹ پٹ اور پاور سپلائی پنز شامل ہیں۔ آفسیٹ نل، کمپنسیشن اور اِن ایبل پن کنفیگریشنز کے لیے مینوفیکچرر کے ڈیٹا شیٹ سے رجوع کریں۔ سگنل کنڈیشننگ اور ایمپلیفائر سرکٹس کے لیے مثالی۔
کے لیے تفصیلی پن آؤٹ ڈیٹا دستیاب نہیں AK5367AEF.
رجوع کریں ڈیٹا شیٹ مکمل پن کنفیگریشن کے لیے۔
عام استعمالات
AK5367AEF کے لیے موزوں ہے 6 ایپلیکیشنs: USB Audio Recording, Digital Microphone Interface, Portable Audio Player, Consumer Audio Capture Accessory, Audio Test and Measurement, Studio Monitoring Interface.
USB Audio Recording
The AK5367AEF fits a stereo USB-audio capture path because it converts two analog channels at 24-bit resolution and supports sampling rates from 32 kHz to 96 kHz. It can sit after a balanced or line-level analog front end and before a USB audio controller, while I2C provides configuration access from the host device. According to the Asahi Kasei Microdevices datasheet, the operating range is 3 V to 3.6 V, so the analog and digital rails should be decoupled independently. The principal design consideration is clock synchronization: the converter must receive valid LRCK and BICK signals or operate according to the documented master-mode arrangement without allowing digital return current to disturb the analog input stage.
تجویز کردہ
Digital Microphone Interface
The AK5367AEF is suitable for a stereo digital-microphone capture design when the transducer or microphone preamplifier produces compatible analog signals. Its 24-bit conversion resolution preserves fine amplitude detail, while the 32 kHz to 96 kHz range supports standard voice, music, and studio-rate recording workflows. According to the Asahi Kasei Microdevices documentation, the IC provides separate analog and digital supply domains and an I2C interface for host control. The analog path must remain short and referenced cleanly to the converter ground, while the I2C and clock traces should be routed away from microphone inputs to reduce coupled disturbance and preserve recording-headroom performance.
تجویز کردہ
Portable Audio Player
The AK5367AEF can serve as the recording-side ADC in a portable audio player that accepts line input from an external source. Its 3 V to 3.6 V analog and digital operating range suits compact systems with a low-voltage audio bus, while the 30-pin VSOP package limits board area compared with a larger converter. According to the Asahi Kasei Microdevices datasheet, the device supports 24-bit stereo operation up to 96 kHz. A portable implementation should account for the converter's clock requirement, active-low power-down behavior, and the need to reset the digital filter after power-up before the host begins capturing audio.
تجویز کردہ
Consumer Audio Capture Accessory
The AK5367AEF is appropriate for a consumer digital-recording accessory that converts stereo line-level audio into a 24-bit digital stream. The supported 32 kHz to 96 kHz range allows the same converter family to serve voice, compact-disc-rate, and high-resolution recording modes. According to the Asahi Kasei Microdevices documentation, the part includes an I2C interface for configuration and clock connections for synchronizing the conversion process. The accessory designer should define analog gain and attenuation before the ADC, isolate clock and digital activity from the input traces, and use the manufacturer pin table to preserve compatibility with the 30-pin, 0.65 mm-pitch VSOP land pattern.
تجویز کردہ
Audio Test and Measurement
The AK5367AEF can be used in an audio measurement front end where a 24-bit stereo converter is required to capture signals at 32 kHz to 96 kHz. Its resolution provides a suitable conversion format for measurement and monitoring equipment, while the I2C interface can support host-controlled configuration. According to the Asahi Kasei Microdevices datasheet, the AKD5367 evaluation board is intended for evaluating the AK5367A family. Instrument designers should verify the applicable input bandwidth, dynamic-range test conditions, clock jitter sensitivity, and grounding arrangement from the manufacturer datasheet before defining the measurement front end.
تجویز کردہ
Studio Monitoring Interface
The AK5367AEF is suitable for the input-conversion stage of a studio monitoring interface when 24-bit stereo capture and sampling rates through 96 kHz are required. The converter can feed a digital audio processor or recording engine, and its I2C interface permits centralized configuration. According to the Asahi Kasei Microdevices datasheet, the device operates from 3 V to 3.6 V and includes power-down control. In a studio-oriented product, analog input routing should minimize interference from display, power-converter, and digital-clock circuitry. The implementation should also include stable references, local supply decoupling, and a documented startup sequence to ensure the digital filter is reset correctly.
تجویز کردہ
تجویز کردہ پروڈکٹس کا خلاصہ
کے لیے انجینئرنگ ریفرنس ڈیٹا AK5367AEF — موازنہ، ڈیزائن رہنمائی، اور تعمیل کی معلومات۔
انتخاب کی گائیڈ
Do not select a replacement solely because it is a stereo ADC with a similar resolution. A true drop-in alternative must match the 30-pin, 0.65 mm-pitch VSOP land pattern, analog input assignments, LRCK and BICK behavior, I2C address and registers, PDN polarity, supply levels, and startup requirements. No competing part is currently verified as meeting those constraints. Until a qualified alternative is documented, existing production demand is best handled as an obsolete-part procurement exercise with an incoming-inspection and traceability plan.
متبادلات کے ساتھ موازنہ
| پیرامیٹر | یہ پروڈکٹ |
|---|---|
| Brand | Asahi Kasei Microdevices |
| Package | 30-pin VSOP |
| Package Pitch | 0.65 mm |
| Converter Type | Stereo ADC |
| Resolution | 24 bit |
| Sampling Rate | 32 kHz to 96 kHz |
| Analog Supply Voltage | 3 V to 3.6 V |
| Digital Supply Voltage | 3 V to 3.6 V |
| Control Interface | I2C |
| Operating Temperature | -20 °C to +85 °C |
ڈیزائن نوٹس
Place the analog and digital bypass capacitors directly beside their corresponding supply pins, and keep the analog input traces short and away from LRCK, BICK, and I2C routing. Use the pin-description table in the manufacturer datasheet when assigning the 30-pin, 0.65 mm-pitch VSOP land pattern. The analog and digital grounds should meet according to the recommended application circuit so that converter return current does not flow through the sensitive input reference path.
Use a low-noise 3 V to 3.6 V supply for the analog domain and a separate 3 V to 3.6 V rail for the digital domain. The two domains should be decoupled at the package pins even if they share a source. Power sequencing must satisfy the manufacturer's startup procedure, and the digital filter must be reset after power-up before normal conversion begins. Treat PDN as active low and avoid pulling it to an undefined state during reset.
Route LRCK and BICK as short, continuous clock traces and use the manufacturer's timing values to determine whether additional source termination or series damping is necessary. Keep I2C routing separate from the analog input network where practical. Because the converter can operate up to 96 kHz, clock jitter and coupling from adjacent digital circuitry can affect capture performance even when nominal resolution and sample-rate settings are correct.
Do not substitute a generic 30-pin VSOP audio converter without checking the complete pin-description table, package drawing, supply levels, clock mode, I2C address, register map, and control-signal polarity. Matching the number of pins and the sampling rate alone is insufficient for drop-in qualification. Because AK5367AEF is obsolete, an incoming alternative should also be reviewed for lifecycle risk and long-term availability before production release.
تعمیل کی معلومات
The product is an obsolete consumer-audio ADC. RoHS, REACH, lead-free, halogen-free, and conflict-minerals status are not stated in the manufacturer or distributor documentation represented for this part.