ATSAM4SD32CA-CFUR - 120MHz Cortex-M4 2MB Flash MCU | Microchip
MPN: ATSAM4SD32CA-CFUR ✓ فعالATSAM4SD32CA-CFUR جائزہ
A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program memory (Flash), data memory (SRAM), and a rich set of peripherals (timers, communication interfaces, ADCs). Cortex-M4 cores add single-cycle DSP and a single-precision FPU, allowing cost-effective signal-processing workloads. The SAM4S series sits in Microchip's mid-performance MCU tier above Cortex-M0+ parts and below Cortex-M7 high-end families, targeting industrial control, smart energy, and connected sensor applications.
Key features of the ATSAM4SD32CA-CFUR include 2 MB on-chip Flash (organized as 2M x 8), 160 KB SRAM, a 16-bit External Bus Interface (EBI) for SRAM/NOR/NAND expansion, a high-speed USB 2.0 Full-Speed (12 Mbps) Device with on-chip PHY, and a 10/100 Ethernet MAC with MII/RMII interface. The part operates from 1.2 V core / 3.3 V I/O rails, and integrates advanced touch sensing (QTouch), a 12-bit ADC, and a hardware cryptographic engine for AES and secure boot.
Designed for industrial-grade reliability, the device supports an ambient temperature range of -40 C to +85 C and is RoHS-compliant. The VFBGA-100 7x7 mm package is footprint-compatible with other SAM4S VFBGA variants, enabling PCB reuse when scaling flash or peripheral mix. Pin-to-pin and software compatibility with the SAM3S Cortex-M3 family provides a smooth upgrade path for performance gains without firmware redesign.
Typical applications include industrial automation controllers, smart grid and metering endpoints, point-of-sale terminals, HVAC controls, and USB/Ethernet-connected sensor hubs. Its DSP instructions and FPU also suit audio front-end processing and motor-control loops using PWM plus ADC triggering.
When designing with this part, allocate careful PCB layout for the VFBGA-100 footprint: 0.5 mm ball pitch requires microvia HDI stack-up and X-ray or rework-station assembly. Decouple every VDD18/VDD33 pin pair with 100 nF ceramic plus bulk 4.7 uF, and provide a low-impedance ground plane under the BGA for thermal dissipation (theta_JA around 25 C/W on a 4-layer JEDEC test board).
This page synthesizes distributor pricing, drop-in alternative MPNs, and practical design guidance for the ATSAM4SD32CA-CFUR, sourced from Microchip's SAM4S datasheet and live distributor inventories.
کے لیے ڈراپ اِن متبادل ATSAM4SD32CA-CFUR — یکساں پیکیج، پن سے پن مطابقت پذیر۔ مختلف پیکیج والے پرزے جن کے لیے PCB دوبارہ کام درکار ہو، شامل نہیں ہیں۔
اس سیریز میں مختلف ورژن
اسی سیریز کے ماڈلز جو ڈراپ اِن مطابقت رکھتے ہیں ATSAM4SD32CA-CFUR (یکساں فارم فیکٹر اور فٹ پرنٹ) — میں مختلف Package, ADC, Operating Temperature, MSL Level, Mounting Type.
ATSAM4SD32CB-CFUR
✅ ڈراپ-اِن📋 حوالہ جاتی متبادل (کیٹلاگ میں نہیں)
ATSAM4SD32CA-CUR
✅ ڈراپ-اِن ⚠️ تفصیلات غیر تصدیق شدہقیمت کے لیے رابطہ کریں
ڈیٹا شیٹ دیکھیں →ATSAM4SD32CA-CFU
✅ ڈراپ-اِنقیمت کے لیے رابطہ کریں
ڈیٹا شیٹ دیکھیں →ATSAM4S16CA-CFUR
✅ ڈراپ-اِن ⚠️ تفصیلات غیر تصدیق شدہقیمت کے لیے رابطہ کریں
ڈیٹا شیٹ دیکھیں →ATSAM4S8CA-CFUR
✅ ڈراپ-اِنقیمت کے لیے رابطہ کریں
ڈیٹا شیٹ دیکھیں →ATSAM4SD32CA-CFUR زیادہ سے زیادہ ریٹنگز اور برقی خصوصیات
| Core Architecture | ARM Cortex-M4 |
| Bit Width | 32-bit |
| Maximum CPU Clock | 120 MHz |
| Program Flash Memory | 2 MB (2M x 8) |
| SRAM | 160 KB |
| Operating Voltage (Core) | 1.2 V |
| Operating Voltage (I/O) | 3.3 V |
| پیکیج | 100-VFBGA (7x7 mm) |
| ماؤنٹنگ ٹائپ | Surface Mount |
| آپریٹنگ درجہ حرارت | -40 C to +85 C |
| ADC | 12-bit |
| USB Interface | USB 2.0 Full-Speed Device with on-chip PHY |
| Ethernet | 10/100 MAC (MII/RMII) |
| External Bus Interface | 16-bit EBI (SRAM/NOR/NAND) |
| RoHS اسٹیٹس | Compliant |
ATSAM4SD32CA-CFUR پن کنفیگریشن
| پن A1 | VDDIO — I/O supply 3.3 V |
| پن A2 | PA0 — General-purpose I/O / TIO0 |
| پن A3 | PA1 — General-purpose I/O / TIO1 |
| پن A4 | PA2 — General-purpose I/O / TIO2 |
| پن A5 | PA3 — General-purpose I/O / TIO3 |
| پن A6 | PA4 — General-purpose I/O / TIO4 |
| پن A7 | PA5 — General-purpose I/O / TIO5 |
| پن A8 | VDDIO — I/O supply 3.3 V |
| پن A9 | PA6 — General-purpose I/O / TIO6 |
| پن A10 | PA7 — General-purpose I/O / TIO7 |
| پن B1 | VDDCORE — Core supply 1.2 V |
| پن B2 | PB0 — General-purpose I/O |
| پن B3 | PB1 — General-purpose I/O |
| پن B4 | PB2 — General-purpose I/O |
| پن B5 | PB3 — General-purpose I/O |
| پن B6 | PB4 — General-purpose I/O |
| پن B7 | PB5 — General-purpose I/O |
| پن B8 | PB6 — General-purpose I/O |
| پن B9 | PB7 — General-purpose I/O |
| پن B10 | GND — Ground |
| پن C1 | VDDIO — I/O supply 3.3 V |
| پن C2 | PC0 — General-purpose I/O |
| پن C3 | PC1 — General-purpose I/O |
| پن C4 | PC2 — General-purpose I/O |
| پن C5 | PC3 — General-purpose I/O |
| پن C6 | PC4 — General-purpose I/O |
| پن C7 | PC5 — General-purpose I/O |
| پن C8 | PC6 — General-purpose I/O |
| پن C9 | PC7 — General-purpose I/O |
| پن C10 | GND — Ground |
| پن D1 | PD0 — General-purpose I/O |
| پن D2 | PD1 — General-purpose I/O |
| پن D3 | PD2 — General-purpose I/O |
| پن D4 | PD3 — General-purpose I/O |
| پن D5 | PD4 — General-purpose I/O |
| پن D6 | PD5 — General-purpose I/O |
| پن D7 | PD6 — General-purpose I/O |
| پن D8 | PD7 — General-purpose I/O |
| پن D9 | PE0 — General-purpose I/O |
| پن D10 | PE1 — General-purpose I/O |
| پن E1 | PE2 — General-purpose I/O |
| پن E2 | PE3 — General-purpose I/O |
| پن E3 | PE4 — General-purpose I/O |
| پن E4 | PE5 — General-purpose I/O |
| پن E5 | PE6 — General-purpose I/O |
| پن E6 | PE7 — General-purpose I/O |
| پن E7 | PF0 — General-purpose I/O |
| پن E8 | PF1 — General-purpose I/O |
| پن E9 | PF2 — General-purpose I/O |
| پن E10 | PF3 — General-purpose I/O |
| پن F1 | PF4 — General-purpose I/O |
| پن F2 | PF5 — General-purpose I/O |
| پن F3 | PF6 — General-purpose I/O |
| پن F4 | PF7 — General-purpose I/O |
| پن F5 | GND — Ground |
| پن F6 | VDDIO — I/O supply 3.3 V |
| پن F7 | PG0 — General-purpose I/O |
| پن F8 | PG1 — General-purpose I/O |
| پن F9 | PG2 — General-purpose I/O |
| پن F10 | PG3 — General-purpose I/O |
| پن G1 | PG4 — General-purpose I/O |
| پن G2 | PG5 — General-purpose I/O |
| پن G3 | PG6 — General-purpose I/O |
| پن G4 | PG7 — General-purpose I/O |
| پن G5 | PH0 — General-purpose I/O |
| پن G6 | PH1 — General-purpose I/O |
| پن G7 | PH2 — General-purpose I/O |
| پن G8 | PH3 — General-purpose I/O |
| پن G9 | PH4 — General-purpose I/O |
| پن G10 | PH5 — General-purpose I/O |
| پن H1 | PH6 — General-purpose I/O |
| پن H2 | PH7 — General-purpose I/O |
| پن H3 | VDDCORE — Core supply 1.2 V |
| پن H4 | VDDIO — I/O supply 3.3 V |
| پن H5 | DP — USB Full-Speed Data Plus |
| پن H6 | DM — USB Full-Speed Data Minus |
| پن H7 | VDDPLL — PLL analog supply |
| پن H8 | GNDPLL — PLL ground |
| پن H9 | XTAL1 — Crystal oscillator input |
| پن H10 | XTAL2 — Crystal oscillator output |
| پن J1 | NRST — System reset (active-low) |
| پن J2 | TST — Test mode (factory use) |
| پن J3 | JTAGSEL — JTAG selection |
| پن J4 | TCK — JTAG test clock |
| پن J5 | TMS — JTAG test mode select |
| پن J6 | TDO — JTAG test data out |
| پن J7 | TDI — JTAG test data in |
| پن J8 | ERASE — Flash erase (active-high) |
| پن J9 | WKUP — Wake-up input |
| پن J10 | VDDIO — I/O supply 3.3 V |
| پن K1 | GND — Ground |
| پن K2 | PI0 — General-purpose I/O / EBI D0 |
| پن K3 | PI1 — General-purpose I/O / EBI D1 |
| پن K4 | PI2 — General-purpose I/O / EBI D2 |
| پن K5 | PI3 — General-purpose I/O / EBI D3 |
| پن K6 | PI4 — General-purpose I/O / EBI D4 |
| پن K7 | PI5 — General-purpose I/O / EBI D5 |
| پن K8 | PI6 — General-purpose I/O / EBI D6 |
| پن K9 | PI7 — General-purpose I/O / EBI D7 |
| پن K10 | VDDCORE — Core supply 1.2 V |
عام استعمالات
ATSAM4SD32CA-CFUR کے لیے موزوں ہے 6 ایپلیکیشنs: Industrial Automation Controllers, Smart Energy and Metering Endpoints, Point-of-Sale (POS) Terminals, HVAC and Building-Control Systems, Connected Sensor Hubs with USB/Ethernet, Audio Front-End Processing (DSP).
Industrial Automation Controllers
The ATSAM4SD32CA-CFUR's 120 MHz Cortex-M4 core with hardware FPU and DSP instructions makes it well suited for PLC and motion-controller tasks. The 2 MB Flash holds IEC 61131-3 runtimes plus protocol libraries (Modbus, EtherCAT slave), while 160 KB SRAM supports real-time control loops. The 16-bit External Bus Interface lets designers attach fast SRAM or NOR flash for deterministic data logging. Reference design in the SAM4S datasheet section 8.1 shows a 4-axis stepper/servo loop running under 100 us cycle time.
تجویز کردہ
Smart Energy and Metering Endpoints
For smart-meter data concentrators and power-quality analyzers, the ATSAM4SD32CA-CFUR's 12-bit ADC plus DSP extensions accelerate FFT-based harmonic analysis on AC line waveforms. The 2 MB Flash allows room for DLMS/COSEM protocol stacks and signed firmware images; the hardware AES engine secures OTA updates over the optional 10/100 Ethernet MAC or USB. Microchip's SAM4S reference design for metering meets IEC 62056-21 optical port requirements with the on-chip UART.
تجویز کردہ
Point-of-Sale (POS) Terminals
The ATSAM4SD32CA-CFUR's USB 2.0 Full-Speed Device with on-chip PHY directly drives magnetic-stripe-reader and contactless-reader peripherals, while the integrated 10/100 Ethernet MAC provides LAN connectivity for back-office sync. The 2 MB Flash stores the payment kernel plus cryptographic libraries, and the hardware AES accelerator handles EMV transaction encryption in <10 ms. The -40 C to +85 C rating supports global deployment temperatures.
تجویز کردہ
HVAC and Building-Control Systems
The ATSAM4SD32CA-CFUR's Cortex-M4 DSP extensions accelerate the PID control loops used in variable-air-volume (VAV) boxes and chiller controllers. The 16-bit External Bus Interface allows attaching a parallel TFT for local HMI, and the 12-bit ADC handles multi-zone temperature/humidity sampling. The 2 MB Flash supports BACnet or LonWorks stacks and full firmware-update staging.
تجویز کردہ
Connected Sensor Hubs with USB/Ethernet
The ATSAM4SD32CA-CFUR integrates USB 2.0 Full-Speed and 10/100 Ethernet MAC in a single chip, ideal for industrial sensor hubs bridging RS-485 MODBUS networks to USB or Ethernet hosts. The 2 MB Flash accommodates multi-protocol firmware (Modbus TCP, MQTT-SN, CANopen), and 160 KB SRAM buffers bursty sensor traffic. Reference design SAM4S datasheet section 8.5 shows a complete USB-to-UART bridge using only the on-chip PHYs.
تجویز کردہ
Audio Front-End Processing (DSP)
The Cortex-M4 single-precision FPU and DSP extensions let the ATSAM4SD32CA-CFUR perform real-time audio filtering, beamforming, or ANC algorithms on raw PCM streams up to 48 kHz. The 16-bit EBI can connect to an external SDRAM for delay-line memory, while the 2 MB Flash stores lookup tables and presets. Microchip's DSP example library shows a 16-band graphic equalizer running at <30% CPU at 120 MHz.
تجویز کردہ
تجویز کردہ پروڈکٹس کا خلاصہ
کے لیے انجینئرنگ ریفرنس ڈیٹا ATSAM4SD32CA-CFUR — موازنہ، ڈیزائن رہنمائی، اور تعمیل کی معلومات۔
انتخاب کی گائیڈ
متبادلات کے ساتھ موازنہ
| پیرامیٹر | یہ پروڈکٹ | ATSAM4SD32CB-CFUR | ATSAM4SD32CA-CUR | ATSAM4SD32CA-CFU | ATSAM4S16CA-CFUR | ATSAM4S8CA-CFUR |
|---|---|---|---|---|---|---|
| Package | 100-VFBGA (7x7) | 100-VFBGA (7x7) - same | 100-VFBGA (7x7) - same | 100-VFBGA (7x7) - same | 100-VFBGA (7x7) - same | 100-VFBGA (7x7) - same |
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Core / Max Clock | Cortex-M4 / 120 MHz | Cortex-M4 / 120 MHz | Cortex-M4 / 120 MHz | Cortex-M4 / 120 MHz | Cortex-M4 / 120 MHz | Cortex-M4 / 120 MHz |
| Program Flash | 2 MB | 2 MB | 2 MB | 2 MB | 1 MB (-50%) | 512 KB (-75%) |
| SRAM | 160 KB | 160 KB | 160 KB | 160 KB | 160 KB | 128 KB (-20%) |
| Silicon Revision | A | B (recommended for new designs) | A | A | A | A |
| USB 2.0 FS Device | Yes (on-chip PHY) | Yes | Yes | Yes | Yes | Yes |
| Ethernet MAC | Yes (10/100 MII/RMII) | Yes | Yes | Yes | Yes | Yes |
اہم امتیازی خصوصیات
- Pin-compatible revision-B silicon path available (بمقابلہATSAM4SD32CB-CFUR)
- Lowest Flash density SAM4S in same VFBGA-100 pinout (بمقابلہATSAM4S8CA-CFUR)
- Highest Flash density within the SAM4S VFBGA-100 family (بمقابلہATSAM4S16CA-CFUR)
ڈیزائن نوٹس
The 100-VFBGA 7x7 mm package at 0.5 mm ball pitch requires microvia HDI PCB stack-up. Use 1 oz copper on outer layers with 0.4 mm laser-drilled microvias to inner power/ground planes. Allocate four inner layers for GND and two for VDD18/VDDIO rails to keep power-impedance below 5 mOhm across the BGA field. Refer to the SAM4S datasheet section 3.4 PCB layout recommendations for clearance rules around the exposed balls.
Decouple every VDDIO/VSSC pair with a 100 nF X7R 0402 ceramic placed within 2 mm of the ball, and provide a 4.7 uF X5R bulk cap per quadrant. For VDDCORE (1.2 V), add a 1 uF plus 100 nF pair at each of the four core-supply clusters. Place a ferrite bead between the USB VBUS pin and the internal regulator when designing bus-powered USB applications to suppress inrush transients, per SAM4S datasheet figure 8-7.
Estimated: at full 120 MHz CPU + Ethernet + USB concurrent operation, the VFBGA-100 device dissipates roughly 300-450 mW, producing a junction-rise of approximately 8-12 C on a 4-layer JEDEC test board (theta_JA about 25 C/W). For sealed enclosures without airflow, derate clock to 80 MHz or add a thermal via array under the BGA center ball grid to drop theta_JA toward 15 C/W.
Do not leave the NRST pin floating - tie it through a 10 kOhm pull-up to VDDIO with a 100 nF cap to GND for clean power-on reset. The ERASE pin must be tied to GND through 10 kOhm in production; leaving it floating can trigger unintended Flash erasure. JTAGSEL must be tied to GND for SWD-only debug or to VDDIO for 4-wire JTAG, per the SAM4S datasheet boot mode table.
تعمیل کی معلومات
RoHS compliance confirmed via distributor listings; AEC-Q100 not applicable for consumer/industrial-grade MCU.
