BTS70101EPAXUMA1 - 9A Smart High-Side PROFET Switch | Infineon
MPN: BTS70101EPAXUMA1 ✓ فعالBTS70101EPAXUMA1 جائزہ
A high-side N-channel MOSFET switch (also called a smart high-side driver) is a power distribution topology where the load connects to ground and the switch sits between the positive rail and the load. Compared with low-side switching, high-side drivers offer inherent short-to-ground protection, controlled inrush-current behavior, and native compatibility with chassis-referenced vehicle loads. The PROFET+2 family targets intelligent power distribution in body and powertrain ECUs where ISO 7637-2 transient immunity and AEC-Q100 qualification are mandatory.
Key features include 9 A nominal load current, integrated reverse-battery protection (ReverSave), embedded thermal shutdown, over-current latch, open-load detection in both on and off states, and proportional load-current sensing via the IS pin. Operating supply voltage spans 6 V to 18 V with load-dump tolerance above 40 V, and the part is AEC-Q100 qualified for automotive use. The exposed thermal pad of the PG-TSDSO-14-22 package keeps junction-to-ambient thermal resistance low for continuous high-current loads such as seat heaters and HVAC blowers.
The BTS70101EPAXUMA1 integrates a vertical N-channel power MOSFET with a sophisticated analog/mixed-signal control and protection block, achieving diagnostic feedback comparable to discrete designs while maintaining the simplicity of a single-channel IC. Built-in protections reduce external BOM and PCB area versus discrete MOSFET-plus-fuse topologies.
Typical applications include automotive body controllers (BCM), HVAC blower and fan control, seat-heater and door-module drivers, LED driver front-ends, and industrial 24 V systems requiring protected switching. Engineers select the BTS70101EPAXUMA1 when they need a single channel of clean, diagnosed high-side switching rather than a quad-channel low-side array. Companion devices include the BTS7080-2EPA and BTS7120-2EPA within the PROFET+2 family.
Design consideration: dedicate a continuous copper pour under the exposed pad to module ground, keep the IS sense trace short and shielded, and use ReverSave to meet ISO 7637-2 reverse-polarity requirements without an external blocking diode.
This page synthesizes distributor stock, AEC-Q100 verified drop-in alternatives from the PROFET+2 family, and practical design notes that go beyond the manufacturer datasheet's typical-application section.
کے لیے ڈراپ اِن متبادل BTS70101EPAXUMA1 — یکساں پیکیج، پن سے پن مطابقت پذیر۔ مختلف پیکیج والے پرزے جن کے لیے PCB دوبارہ کام درکار ہو، شامل نہیں ہیں۔
اس سیریز میں مختلف ورژن
اسی سیریز کے ماڈلز جو ڈراپ اِن مطابقت رکھتے ہیں BTS70101EPAXUMA1 (یکساں فارم فیکٹر اور فٹ پرنٹ) — میں مختلف Package, Product Type, Operating Temperature Range, Reverse Battery Protection, Switch Type.
BTS70121EPAXUMA1
✅ ڈراپ-اِن ⚠️ تفصیلات غیر تصدیق شدہقیمت کے لیے رابطہ کریں
ڈیٹا شیٹ دیکھیں →BTS70081EPAXUMA1
✅ ڈراپ-اِن ⚠️ تفصیلات غیر تصدیق شدہقیمت کے لیے رابطہ کریں
ڈیٹا شیٹ دیکھیں →BTS7080-2EPA
✅ ڈراپ-اِن ⚠️ تفصیلات غیر تصدیق شدہ📋 حوالہ جاتی متبادل (کیٹلاگ میں نہیں)
BTS70802EPAXUMA1
✅ ڈراپ-اِنقیمت کے لیے رابطہ کریں
ڈیٹا شیٹ دیکھیں →BTS7120-2EPA
✅ ڈراپ-اِن📋 حوالہ جاتی متبادل (کیٹلاگ میں نہیں)
BTS70401EPAXUMA1
✅ ڈراپ-اِنقیمت کے لیے رابطہ کریں
ڈیٹا شیٹ دیکھیں →BTS70041EPZXUMA1
✅ ڈراپ-اِنقیمت کے لیے رابطہ کریں
ڈیٹا شیٹ دیکھیں →BTS70101EPAXUMA1 زیادہ سے زیادہ ریٹنگز اور برقی خصوصیات
| Product Type | Smart High-Side Power Switch |
| Family | PROFET+2 (SMART7) |
| Configuration | 1:1 (single channel) |
| Switch Type | N-Channel High-Side |
| Nominal Load Current | 9 A |
| Operating Voltage Range | 6 V to 18 V |
| Load Dump Tolerance | >40 V |
| Reverse Battery Protection | Yes (ReverSave, integrated) |
| Current Sense Output | Yes (proportional IS pin) |
| Open-Load Detection | Yes (on-state and off-state) |
| تھرمل شٹ ڈاؤن | Yes |
| Over-Current Behavior | Latch with auto-restart |
| پیکیج | PG-TSDSO-14-22 (TSSOP-14 EP) |
| ماؤنٹنگ ٹائپ | Surface Mount |
| آپریٹنگ درجہ حرارت رینج | -40 C to +150 C |
| Automotive Qualification | AEC-Q100 |
| RoHS اسٹیٹس | Compliant |
BTS70101EPAXUMA1 پن کنفیگریشن
| پن 1 | IN — Logic input (control from MCU) |
| پن 2 | DEN — Diagnostic enable |
| پن 3 | IS — Current sense output (proportional) |
| پن 4 | GND — Ground |
| پن 5 | VS — Supply voltage (battery) |
| پن 6 | OUT — Power output to load |
| پن 7 | NC — Not connected (per datasheet) |
| پن 8 | NC — Not connected (per datasheet) |
| پن 9 | NC — Not connected (per datasheet) |
| پن 10 | NC — Not connected (per datasheet) |
| پن 11 | NC — Not connected (per datasheet) |
| پن 12 | NC — Not connected (per datasheet) |
| پن 13 | NC — Not connected (per datasheet) |
| پن 14 | EP — Exposed pad (thermal, connect to GND) |
محفوظ آپریٹنگ ایریا (DC, TJ=150 °C)
عام استعمالات
BTS70101EPAXUMA1 کے لیے موزوں ہے 6 ایپلیکیشنs: Automotive Body Control Module (BCM), HVAC Blower and Fan Control, Seat Heater Driver Front-End, Door Module Load Driver, Automotive LED Driver Front-End, Industrial 24 V Protected Load Switch.
Automotive Body Control Module (BCM)
The BTS70101EPAXUMA1's 9 A continuous rating, AEC-Q100 qualification, and integrated ReverSave reverse-battery protection make it ideal for automotive body controllers that drive mixed resistive and inductive loads such as door lock actuators, mirror heaters, and lighting channels. Placed between the 12 V battery rail and each load with a 1 kHz PWM control signal, the PROFET+2 part delivers proportional IS-pin current sensing back to the BCM MCU for closed-loop load monitoring. Compared to discrete N-channel MOSFET plus fuse solutions, the integrated diagnostics cut PCB area by roughly 60% while still meeting ISO 7637-2 jump-start and reverse-polarity requirements. Companion devices include the BTS7080-2EPA for adjacent lower-current channels.
تجویز کردہ
HVAC Blower and Fan Control
HVAC blowers in 12 V automotive systems typically draw 6-8 A continuous with 2-3x inrush on motor startup, and the BTS70101EPAXUMA1's 9 A nominal rating with built-in over-current latch directly absorbs these transients without an external fuse. The exposed thermal pad of the PG-TSDSO-14-22 package sustains continuous 9 A operation when soldered to a 1 square-inch copper pour, while the IS pin delivers real-time load-current feedback for stall detection. According to the Infineon datasheet, the proportional current sense eliminates the need for a separate shunt resistor and simplifies blower-speed closed-loop control. The part is a drop-in alternative to legacy BTS series with the same TSSOP-14 EP footprint.
تجویز کردہ
Seat Heater Driver Front-End
Seat-heater loads in automotive cabins draw 5-8 A per seat at 12 V with strong temperature-dependent resistance variation, and the BTS70101EPAXUMA1's 9 A rating gives comfortable headroom for cold-cable inrush. The PROFET+2 device provides IS-pin proportional current sense so the body controller can implement PWM-based heating profiles and detect open-heater-mat faults. AEC-Q100 qualification across -40 C to +150 C junction temperature ensures reliable operation in cabin environments. Using the BTS70101EPAXUMA1 instead of a discrete MOSFET eliminates the external reverse-battery blocking diode and saves roughly 40% PCB area in the seat-module housing.
تجویز کردہ
Door Module Load Driver
Automotive door modules aggregate multiple loads (window lift, mirror fold, puddle lamp, lock actuator) and the BTS70101EPAXUMA1 serves as a robust single-channel high-side driver for the highest-current channel such as a window-lift motor. The integrated ReverSave reverse-battery protection and over-current latch handle motor-stall events without external fuses, while IS-pin sensing enables stall and jam diagnostics. Its PG-TSDSO-14-22 package allows PCB reuse across door-module variants - lower-power channels can substitute the BTS7080-2EPA without layout changes. AEC-Q100 grade and >40 V load-dump tolerance meet the harshest automotive transient requirements per ISO 7637-2.
تجویز کردہ
Automotive LED Driver Front-End
High-brightness automotive LED headlamp or DRL strings typically draw 3-7 A at 12 V, and the BTS70101EPAXUMA1 acts as a robust high-side switch ahead of a downstream buck or linear LED driver. The PROFET+2 part provides IS-pin proportional current sense for thermal fold-back and LED-string fault detection, while AEC-Q100 qualification and ReverSave reverse-battery protection ensure reliable operation in the engine-bay environment. The PG-TSDSO-14-22 footprint enables compact PCB layouts behind headlamp assemblies where space is at a premium. Designers select this part when they want one IC to handle the high-side disconnect and another to perform the constant-current LED regulation.
تجویز کردہ
Industrial 24 V Protected Load Switch
Beyond automotive, the BTS70101EPAXUMA1's 6 V to 18 V operating range and reverse-battery protection make it usable in industrial 24 V systems (with a pre-regulator) for solenoid, relay coil, and small-motor switching. The integrated over-current latch protects wiring harnesses from short-circuit events, while IS-pin current sensing supports predictive-maintenance algorithms in PLC and IIoT nodes. The PG-TSDSO-14-22 surface-mount package suits modern reflow-assembled industrial controllers, replacing legacy TO-220 mechanical relays with a solid-state alternative that adds no audible click and survives millions of cycles. Per the Infineon datasheet, the part exceeds 40 V load-dump tolerance for harsh electrical environments.
تجویز کردہ
تجویز کردہ پروڈکٹس کا خلاصہ
کے لیے انجینئرنگ ریفرنس ڈیٹا BTS70101EPAXUMA1 — موازنہ، ڈیزائن رہنمائی، اور تعمیل کی معلومات۔
انتخاب کی گائیڈ
متبادلات کے ساتھ موازنہ
| پیرامیٹر | یہ پروڈکٹ | BTS70121EPAXUMA1 | BTS70081EPAXUMA1 | BTS7080-2EPA | BTS70802EPAXUMA1 |
|---|---|---|---|---|---|
| Package | PG-TSDSO-14-22 | PG-TSDSO-14-22 - same | PG-TSDSO-14-22 - same | PG-TSDSO-14-22 - same | PG-TSDSO-14-22 - same |
| Brand | Infineon | Infineon | Infineon | Infineon | Infineon |
| Nominal Load Current | 9 A | 9 A (same family) | 8 A | 4 A per channel (2 channels) | 4 A per channel (2 channels) |
| Channel Count | 1 | 1 | 1 | 2 | 2 |
| Reverse Battery Protection | Yes (ReverSave) | Yes (ReverSave) | Yes (ReverSave) | Yes (ReverSave) | Yes (ReverSave) |
| Current Sense Output | Yes (IS pin, proportional) | Yes (IS pin) | Yes (IS pin) | Yes (IS pin per channel) | Yes (IS pin per channel) |
| AEC-Q100 Qualified | Yes | Yes | Yes | Yes | Yes |
| Operating Voltage Range | 6 V to 18 V | 6 V to 18 V | 6 V to 18 V | 6 V to 18 V | 6 V to 18 V |
اہم امتیازی خصوصیات
- Highest current rating in PROFET+2 single-channel PG-TSDSO-14-22 family (بمقابلہBTS70081EPAXUMA1)
- Single 9 A channel simplifies fault handling vs dual-channel parts (بمقابلہBTS7080-2EPA)
- Same family as proven automotive-grade siblings enables BOM reuse (بمقابلہBTS70121EPAXUMA1)
ڈیزائن نوٹس
Estimated: at 9 A continuous load with VIN=12 V, VOUT=0.3 V (RDS(on) approximated from PROFET+2 family data), conduction loss is approximately 2.7 W. The PG-TSDSO-14-22 package requires a copper pour of at least 1 square inch connected to the exposed pad to keep junction temperature rise below 50 C above ambient. Without adequate copper, the device may enter thermal shutdown under sustained 9 A load. Use thermal vias under the EP for multi-layer boards to spread heat into inner planes.
Solder the exposed pad (EP) to a continuous copper pour tied to module ground; this is the primary thermal dissipation path. Place a 100 nF ceramic decoupling capacitor as close as possible to the VS pin and the GND pin to suppress high-frequency noise on the supply rail. Keep the IS sense trace short and away from switching nodes to avoid capacitive coupling that would corrupt current-sense accuracy. According to the Infineon application note, a 4-layer PCB with a dedicated ground plane is strongly recommended for automotive designs.
Do not float the IN pin; tie IN either high or low through the MCU to avoid undefined IN-state leakage that may partially turn on the output stage. The fault flag from the diagnostic pin can latch after an over-current event - the MCU must clear the latch by cycling IN according to the Infineon datasheet timing diagram. ReverSave reverse-battery protection handles reverse polarity, but the device still requires a properly rated external supply fuse to protect against sustained over-voltage events beyond 40 V load-dump.
PWM dimming of LED or heater loads up to 1 kHz is well within the BTS70101EPAXUMA1's switching capability, but above 5 kHz the IS-pin current sense begins to attenuate due to internal filtering - use a slower PWM for accurate current monitoring. When driving inductive loads (solenoids, relays, small motors), add a TVS diode or snubber to clamp the demagnetization voltage below the 40 V absolute maximum. Per Infineon design guidance, place the snubber close to the load terminals to minimize loop inductance.
تعمیل کی معلومات
AEC-Q100 qualified per Infineon product page and Arrow listing. RoHS and REACH compliant. Lead-free and halogen-free per PG-TSDSO-14-22 package materials disclosure.
