BTS70101EPAXUMA1 - 9A Smart High-Side PROFET Switch | Infineon
부품 번호: BTS70101EPAXUMA1 ✓ 활성| 수량 | 단가 | 합계 |
|---|---|---|
| 1 | $2.85 | $2.85 |
| 10 | $2.56 | $25.60 |
| 100 | $2.28 | $228.00 |
| 500 | $2.05 | $1,025.00 |
| 1,000 | $1.84 | $1,840.00 |
BTS70101EPAXUMA1 개요
A high-side N-channel MOSFET switch (also called a smart high-side driver) is a power distribution topology where the load connects to ground and the switch sits between the positive rail and the load. Compared with low-side switching, high-side drivers offer inherent short-to-ground protection, controlled inrush-current behavior, and native compatibility with chassis-referenced vehicle loads. The PROFET+2 family targets intelligent power distribution in body and powertrain ECUs where ISO 7637-2 transient immunity and AEC-Q100 qualification are mandatory.
Key features include 9 A nominal load current, integrated reverse-battery protection (ReverSave), embedded thermal shutdown, over-current latch, open-load detection in both on and off states, and proportional load-current sensing via the IS pin. Operating supply voltage spans 6 V to 18 V with load-dump tolerance above 40 V, and the part is AEC-Q100 qualified for automotive use. The exposed thermal pad of the PG-TSDSO-14-22 package keeps junction-to-ambient thermal resistance low for continuous high-current loads such as seat heaters and HVAC blowers.
The BTS70101EPAXUMA1 integrates a vertical N-channel power MOSFET with a sophisticated analog/mixed-signal control and protection block, achieving diagnostic feedback comparable to discrete designs while maintaining the simplicity of a single-channel IC. Built-in protections reduce external BOM and PCB area versus discrete MOSFET-plus-fuse topologies.
Typical applications include automotive body controllers (BCM), HVAC blower and fan control, seat-heater and door-module drivers, LED driver front-ends, and industrial 24 V systems requiring protected switching. Engineers select the BTS70101EPAXUMA1 when they need a single channel of clean, diagnosed high-side switching rather than a quad-channel low-side array. Companion devices include the BTS7080-2EPA and BTS7120-2EPA within the PROFET+2 family.
Design consideration: dedicate a continuous copper pour under the exposed pad to module ground, keep the IS sense trace short and shielded, and use ReverSave to meet ISO 7637-2 reverse-polarity requirements without an external blocking diode.
This page synthesizes distributor stock, AEC-Q100 verified drop-in alternatives from the PROFET+2 family, and practical design notes that go beyond the manufacturer datasheet's typical-application section.
드롭인 대체품: BTS70101EPAXUMA1 — 동일 패키지, 핀 호환. PCB 재작업이 필요한 다른 패키지 부품은 제외됩니다.
이 시리즈의 변형
다음과 드롭인 호환되는 동일 시리즈 모델: BTS70101EPAXUMA1 (동일 폼 팩터 및 풋프린트) — 차이점: Package, Product Type, Operating Temperature Range, Reverse Battery Protection, Switch Type.
빠른 비교 도구 — 나란히 비교할 대체 부품을 선택하십시오:
BTS70121EPAXUMA1
✅ 드롭인 ⚠️ 사양 미검증✓ 재고 있음
$1.05 / 개
데이터시트 보기 →BTS70081EPAXUMA1
✅ 드롭인 ⚠️ 사양 미검증✓ 재고 있음
$0.96 / 개
데이터시트 보기 →BTS7080-2EPA
✅ 드롭인 ⚠️ 사양 미검증📋 참조 대체품 (카탈로그에 없음)
BTS70802EPAXUMA1
✅ 드롭인✓ 재고 있음
$1.32 / 개
데이터시트 보기 →BTS7120-2EPA
✅ 드롭인📋 참조 대체품 (카탈로그에 없음)
BTS70401EPAXUMA1
✅ 드롭인✓ 재고 있음
$1.05 / 개
데이터시트 보기 →BTS70041EPZXUMA1
✅ 드롭인✓ 재고 있음
$1.05 / 개
데이터시트 보기 →BTS70101EPAXUMA1 최대 정격 & 전기적 특성
| Product Type | Smart High-Side Power Switch |
| Family | PROFET+2 (SMART7) |
| Configuration | 1:1 (single channel) |
| Switch Type | N-Channel High-Side |
| Nominal Load Current | 9 A |
| Operating Voltage Range | 6 V to 18 V |
| Load Dump Tolerance | >40 V |
| Reverse Battery Protection | Yes (ReverSave, integrated) |
| Current Sense Output | Yes (proportional IS pin) |
| Open-Load Detection | Yes (on-state and off-state) |
| 열 차단 | Yes |
| Over-Current Behavior | Latch with auto-restart |
| 패키지 | PG-TSDSO-14-22 (TSSOP-14 EP) |
| 실장 유형 | Surface Mount |
| 동작 온도 범위 | -40 C to +150 C |
| Automotive Qualification | AEC-Q100 |
| RoHS 상태 | Compliant |
BTS70101EPAXUMA1 핀 구성
| 핀 1 | IN — Logic input (control from MCU) |
| 핀 2 | DEN — Diagnostic enable |
| 핀 3 | IS — Current sense output (proportional) |
| 핀 4 | GND — Ground |
| 핀 5 | VS — Supply voltage (battery) |
| 핀 6 | OUT — Power output to load |
| 핀 7 | NC — Not connected (per datasheet) |
| 핀 8 | NC — Not connected (per datasheet) |
| 핀 9 | NC — Not connected (per datasheet) |
| 핀 10 | NC — Not connected (per datasheet) |
| 핀 11 | NC — Not connected (per datasheet) |
| 핀 12 | NC — Not connected (per datasheet) |
| 핀 13 | NC — Not connected (per datasheet) |
| 핀 14 | EP — Exposed pad (thermal, connect to GND) |
안전 동작 영역 (DC, TJ=150 °C)
일반적인 애플리케이션
BTS70101EPAXUMA1 적합 용도: 6 애플리케이션s: Automotive Body Control Module (BCM), HVAC Blower and Fan Control, Seat Heater Driver Front-End, Door Module Load Driver, Automotive LED Driver Front-End, Industrial 24 V Protected Load Switch.
Automotive Body Control Module (BCM)
The BTS70101EPAXUMA1's 9 A continuous rating, AEC-Q100 qualification, and integrated ReverSave reverse-battery protection make it ideal for automotive body controllers that drive mixed resistive and inductive loads such as door lock actuators, mirror heaters, and lighting channels. Placed between the 12 V battery rail and each load with a 1 kHz PWM control signal, the PROFET+2 part delivers proportional IS-pin current sensing back to the BCM MCU for closed-loop load monitoring. Compared to discrete N-channel MOSFET plus fuse solutions, the integrated diagnostics cut PCB area by roughly 60% while still meeting ISO 7637-2 jump-start and reverse-polarity requirements. Companion devices include the BTS7080-2EPA for adjacent lower-current channels.
추천
HVAC Blower and Fan Control
HVAC blowers in 12 V automotive systems typically draw 6-8 A continuous with 2-3x inrush on motor startup, and the BTS70101EPAXUMA1's 9 A nominal rating with built-in over-current latch directly absorbs these transients without an external fuse. The exposed thermal pad of the PG-TSDSO-14-22 package sustains continuous 9 A operation when soldered to a 1 square-inch copper pour, while the IS pin delivers real-time load-current feedback for stall detection. According to the Infineon datasheet, the proportional current sense eliminates the need for a separate shunt resistor and simplifies blower-speed closed-loop control. The part is a drop-in alternative to legacy BTS series with the same TSSOP-14 EP footprint.
추천
Seat Heater Driver Front-End
Seat-heater loads in automotive cabins draw 5-8 A per seat at 12 V with strong temperature-dependent resistance variation, and the BTS70101EPAXUMA1's 9 A rating gives comfortable headroom for cold-cable inrush. The PROFET+2 device provides IS-pin proportional current sense so the body controller can implement PWM-based heating profiles and detect open-heater-mat faults. AEC-Q100 qualification across -40 C to +150 C junction temperature ensures reliable operation in cabin environments. Using the BTS70101EPAXUMA1 instead of a discrete MOSFET eliminates the external reverse-battery blocking diode and saves roughly 40% PCB area in the seat-module housing.
추천
Door Module Load Driver
Automotive door modules aggregate multiple loads (window lift, mirror fold, puddle lamp, lock actuator) and the BTS70101EPAXUMA1 serves as a robust single-channel high-side driver for the highest-current channel such as a window-lift motor. The integrated ReverSave reverse-battery protection and over-current latch handle motor-stall events without external fuses, while IS-pin sensing enables stall and jam diagnostics. Its PG-TSDSO-14-22 package allows PCB reuse across door-module variants - lower-power channels can substitute the BTS7080-2EPA without layout changes. AEC-Q100 grade and >40 V load-dump tolerance meet the harshest automotive transient requirements per ISO 7637-2.
추천
Automotive LED Driver Front-End
High-brightness automotive LED headlamp or DRL strings typically draw 3-7 A at 12 V, and the BTS70101EPAXUMA1 acts as a robust high-side switch ahead of a downstream buck or linear LED driver. The PROFET+2 part provides IS-pin proportional current sense for thermal fold-back and LED-string fault detection, while AEC-Q100 qualification and ReverSave reverse-battery protection ensure reliable operation in the engine-bay environment. The PG-TSDSO-14-22 footprint enables compact PCB layouts behind headlamp assemblies where space is at a premium. Designers select this part when they want one IC to handle the high-side disconnect and another to perform the constant-current LED regulation.
추천
Industrial 24 V Protected Load Switch
Beyond automotive, the BTS70101EPAXUMA1's 6 V to 18 V operating range and reverse-battery protection make it usable in industrial 24 V systems (with a pre-regulator) for solenoid, relay coil, and small-motor switching. The integrated over-current latch protects wiring harnesses from short-circuit events, while IS-pin current sensing supports predictive-maintenance algorithms in PLC and IIoT nodes. The PG-TSDSO-14-22 surface-mount package suits modern reflow-assembled industrial controllers, replacing legacy TO-220 mechanical relays with a solid-state alternative that adds no audible click and survives millions of cycles. Per the Infineon datasheet, the part exceeds 40 V load-dump tolerance for harsh electrical environments.
추천
추천 제품 요약
엔지니어링 참조 데이터: BTS70101EPAXUMA1 — 비교, 설계 지침 및 규정 준수 정보.
선택 가이드
대체품과의 비교
| 파라미터 | 이 제품 | BTS70121EPAXUMA1 | BTS70081EPAXUMA1 | BTS7080-2EPA | BTS70802EPAXUMA1 |
|---|---|---|---|---|---|
| Package | PG-TSDSO-14-22 | PG-TSDSO-14-22 - same | PG-TSDSO-14-22 - same | PG-TSDSO-14-22 - same | PG-TSDSO-14-22 - same |
| Brand | Infineon | Infineon | Infineon | Infineon | Infineon |
| Nominal Load Current | 9 A | 9 A (same family) | 8 A | 4 A per channel (2 channels) | 4 A per channel (2 channels) |
| Channel Count | 1 | 1 | 1 | 2 | 2 |
| Reverse Battery Protection | Yes (ReverSave) | Yes (ReverSave) | Yes (ReverSave) | Yes (ReverSave) | Yes (ReverSave) |
| Current Sense Output | Yes (IS pin, proportional) | Yes (IS pin) | Yes (IS pin) | Yes (IS pin per channel) | Yes (IS pin per channel) |
| AEC-Q100 Qualified | Yes | Yes | Yes | Yes | Yes |
| Operating Voltage Range | 6 V to 18 V | 6 V to 18 V | 6 V to 18 V | 6 V to 18 V | 6 V to 18 V |
주요 차별점
- Highest current rating in PROFET+2 single-channel PG-TSDSO-14-22 family (vs BTS70081EPAXUMA1)
- Single 9 A channel simplifies fault handling vs dual-channel parts (vs BTS7080-2EPA)
- Same family as proven automotive-grade siblings enables BOM reuse (vs BTS70121EPAXUMA1)
설계 노트
Estimated: at 9 A continuous load with VIN=12 V, VOUT=0.3 V (RDS(on) approximated from PROFET+2 family data), conduction loss is approximately 2.7 W. The PG-TSDSO-14-22 package requires a copper pour of at least 1 square inch connected to the exposed pad to keep junction temperature rise below 50 C above ambient. Without adequate copper, the device may enter thermal shutdown under sustained 9 A load. Use thermal vias under the EP for multi-layer boards to spread heat into inner planes.
Solder the exposed pad (EP) to a continuous copper pour tied to module ground; this is the primary thermal dissipation path. Place a 100 nF ceramic decoupling capacitor as close as possible to the VS pin and the GND pin to suppress high-frequency noise on the supply rail. Keep the IS sense trace short and away from switching nodes to avoid capacitive coupling that would corrupt current-sense accuracy. According to the Infineon application note, a 4-layer PCB with a dedicated ground plane is strongly recommended for automotive designs.
Do not float the IN pin; tie IN either high or low through the MCU to avoid undefined IN-state leakage that may partially turn on the output stage. The fault flag from the diagnostic pin can latch after an over-current event - the MCU must clear the latch by cycling IN according to the Infineon datasheet timing diagram. ReverSave reverse-battery protection handles reverse polarity, but the device still requires a properly rated external supply fuse to protect against sustained over-voltage events beyond 40 V load-dump.
PWM dimming of LED or heater loads up to 1 kHz is well within the BTS70101EPAXUMA1's switching capability, but above 5 kHz the IS-pin current sense begins to attenuate due to internal filtering - use a slower PWM for accurate current monitoring. When driving inductive loads (solenoids, relays, small motors), add a TVS diode or snubber to clamp the demagnetization voltage below the 40 V absolute maximum. Per Infineon design guidance, place the snubber close to the load terminals to minimize loop inductance.
규정 준수 정보
AEC-Q100 qualified per Infineon product page and Arrow listing. RoHS and REACH compliant. Lead-free and halogen-free per PG-TSDSO-14-22 package materials disclosure.
