Renesas Electronics

DG406DJZ - 16:1 CMOS Analog Multiplexer | Renesas

MPN: DG406DJZ ✓ فعال
100 ohm maximum Rds(on) 28-pin PDIP Package
MOQ: 1 |

DG406DJZ جائزہ

The Renesas Electronics DG406DJZ is a single 16:1 CMOS analog multiplexer with 100 ohm on-state resistance, housed in a 28-pin PDIP package. It combines a 16-channel analog switch array with TTL- and CMOS-compatible channel decoding, an enable input for device selection, and an internal voltage reference for logic thresholds. These characteristics make the DG406DJZ suitable for routing one analog signal source among as many as 16 external inputs.

A CMOS analog multiplexer is an interface IC that connects multiple signal paths to one shared internal node. Its position in the hierarchy is analog switch -> multiplexer -> interface IC -> semiconductor. Unlike a mechanical switch, the DG406DJZ changes channels electronically according to binary select inputs, allowing a microcontroller or other digital controller to scan sensors, measurements, or communication lines efficiently.

The DG406DJZ uses four binary select inputs to address 16 channels. Its enable function allows the selected device to be disabled while other multiplexers share the same system bus, which is useful in larger routing or measurement systems. The 100 ohm maximum on-state resistance and TTL/CMOS-compatible decoding simplify interface design in both legacy and modern control systems.

The monolithic CMOS implementation integrates 16 analog switches, address decoding, logic-threshold referencing, and enable control. According to the Renesas DG406 and DG407 datasheet, this device family was designed as a drop-in replacement for the popular DG506A and DG507A series. That heritage supports board-level modernization when existing multiplexer footprints must be retained.

Typical applications include data-acquisition systems, audio signal routing, test equipment, communication systems, sample-and-hold circuits, and guidance or control systems. The enable input is particularly useful when several multiplexers share a common output or when a system requires deliberate isolation of an inactive routing node.

When laying out a PCB, place the selected signal source and destination traces away from digital address and enable lines, and terminate unused channels according to the manufacturer's application guidance. Check the absolute maximum ratings, supply-voltage limits, and switch-state behavior in the datasheet before applying signals or changing the logic reference configuration.

This product page combines the manufacturer family documentation, verified distributor packaging information, a focused comparison of genuine 28-pin alternatives, and practical integration guidance for engineers evaluating the DG406DJZ as a retrofit or new-design multiplexer.

کے لیے ڈراپ اِن متبادل DG406DJZ — یکساں پیکیج، پن سے پن مطابقت پذیر۔ مختلف پیکیج والے پرزے جن کے لیے PCB دوبارہ کام درکار ہو، شامل نہیں ہیں۔

اس سیریز میں مختلف ورژن

اسی سیریز کے ماڈلز جو ڈراپ اِن مطابقت رکھتے ہیں DG406DJZ (یکساں فارم فیکٹر اور فٹ پرنٹ) — میں مختلف Multiplexer Configuration.

Analog Devices
Multiplexer Configuration: 16:1 single-ended
موازنہ کریں DG406DJZ →

DG406DJ+

✅ ڈراپ-اِن
Analog Devices
📦 28-pin PDIP
16:1 single-ended · 16 channels · 1 circuit · 100 ohm · 8 ohm maximum · 9 ohm maximum · 15 pC · 5 nA maximum at +85°C

قیمت کے لیے رابطہ کریں

ڈیٹا شیٹ دیکھیں →

DG406DJ+

✅ ڈراپ-اِن
Analog Devices
📦 28-pin PDIP
16:1 single-ended · 16 channels · 1 circuit · 100 ohm · 8 ohm maximum · 9 ohm maximum · 15 pC · 5 nA maximum at +85°C

قیمت کے لیے رابطہ کریں

ڈیٹا شیٹ دیکھیں →

DG406DJZ-E3

✅ ڈراپ-اِن
📦 28-pin PDIP
Same DG406 16:1 architecture in a 28-pin PDIP package; ordering suffix and manufacturer-specific qualification details differ.

📋 حوالہ جاتی متبادل (کیٹلاگ میں نہیں)

DG406DJ+

✅ ڈراپ-اِن
Analog Devices
📦 28-pin PDIP
16:1 single-ended · 16 channels · 1 circuit · 100 ohm · 8 ohm maximum · 9 ohm maximum · 15 pC · 5 nA maximum at +85°C

قیمت کے لیے رابطہ کریں

ڈیٹا شیٹ دیکھیں →

DG406DJZ

✅ ڈراپ-اِن
Renesas Electronics
📦 28-pin PDIP
1 circuit IC switch · 16:1 · 16 channels · 100 ohm maximum · 1 circuit · 28-pin PDIP · 28 pins

قیمت کے لیے رابطہ کریں

ڈیٹا شیٹ دیکھیں →

DG406DJZ تفصیلات

Product Type 1 circuit IC switch
Multiplexer Configuration 16:1
Number of Channels 16 channels
On-State Resistance 100 ohm maximum
Number of Circuits 1 circuit
پیکیج 28-pin PDIP
پن کی تعداد 28 pins
ماؤنٹنگ ٹائپ Through-hole
Logic Compatibility TTL and CMOS compatible
Enable Control Yes
Logic Threshold Reference Internal voltage reference
Lead-Free Status Lead free
RoHS اسٹیٹس RoHS compliant

DG406DJZ 28-pin pdip پن کنفیگریشن گائیڈ

DG406DJZ (28-pin pdip پیکیج) کے لیے پن کنفیگریشن۔ پن نمبرنگ، فنکشنز اور کنکشن ڈایاگرامز مینوفیکچرر کے ڈیٹا شیٹ میں بیان کیے گئے ہیں۔ درست فٹ پرنٹ اور سولڈرنگ رہنما ہدایات کے لیے اسی سے رجوع کریں۔

DG406DJZ کے لیے 28-pin pdip پیکیج پن آؤٹ ڈایاگرام

کے لیے تفصیلی پن آؤٹ ڈیٹا دستیاب نہیں DG406DJZ.

رجوع کریں ڈیٹا شیٹ مکمل پن کنفیگریشن کے لیے۔

عام استعمالات

DG406DJZ کے لیے موزوں ہے 6 ایپلیکیشنs: Multichannel Data Acquisition, Audio Signal Routing, Test and Measurement Systems, Communication Signal Multiplexing, Sample-and-Hold Signal Conditioning, Guidance and Control Systems.

🏭

Multichannel Data Acquisition

The DG406DJZ fits data-acquisition front ends that scan up to 16 analog inputs with one shared converter input. Four select lines address the channel while the enable input gives the controller a way to disable the device when multiple routing nodes coexist. Its 100 ohm maximum on-state resistance must be included in the acquisition-time calculation, particularly when driving a high-impedance ADC input. Keeping the multiplexed trace short helps prevent the added switch resistance and node capacitance from limiting settling accuracy. The 16:1 arrangement also reduces analog routing hardware compared with bringing every sensor channel directly to the converter.

🎧

Audio Signal Routing

The DG406DJZ can route one of 16 audio or control lines to a common amplifier, codec, or measurement input. Its monolithic CMOS implementation avoids the mechanical contact resistance and switching transients associated with traditional rotary selection. The 100 ohm maximum on-state resistance is acceptable for many line-level audio paths but can create excessive attenuation when combined with a high source impedance. Keep the selected trace away from digital address lines and use a low-impedance input stage when signal level and distortion requirements are tight.

🖥️

Test and Measurement Systems

The DG406DJZ is useful in test equipment that must connect one of 16 sources to a common instrument input. Digital channel selection permits repeatable matrix-style routing, while enable control supports systems containing more than one multiplexer. The 100 ohm maximum on-state resistance contributes to source loading, so the test plan should include the impedance of the source, cable, and measurement input. For high-frequency or low-amplitude measurements, verify settling behavior and channel matching in the manufacturer electrical-characteristics tables before using the device as a precision scanner.

🌐

Communication Signal Multiplexing

The DG406DJZ can select among 16 communication or line-level inputs for centralized monitoring. TTL- and CMOS-compatible decoding makes the address interface practical for common digital controllers, while the enable function helps isolate inactive devices on a shared bus. Designers should not interpret the 100 ohm maximum on-state resistance as suitable for every communications standard; impedance, logic levels, insertion loss, and crosstalk requirements depend on the line being routed. A controlled ground-plane layout and short analog paths will reduce coupling from the rapidly changing select signals.

🔧

Sample-and-Hold Signal Conditioning

The DG406DJZ can present one selected input to a sample-and-hold or acquisition circuit, making it appropriate for sequential signal conditioning. Four binary select inputs define the active source, and enable provides an additional control point for system sequencing. The switch's 100 ohm maximum on-state resistance must be combined with source impedance and acquisition capacitance to estimate settling performance. Keep the multiplexer close to the sampling node, use a defined return path, and confirm that no selected channel can exceed the applicable analog signal limits.

✈️

Guidance and Control Systems

The DG406DJZ supports guidance and control systems that monitor multiple analog feedback channels using a shared controller. Sixteen channels provide useful consolidation when sensors are slower than the digital control loop, and the enable input helps coordinate multiple multiplexers during mode changes. The maximum on-state resistance of 100 ohm can affect sensor loading or amplifier headroom, so each channel should be evaluated for bias current, impedance, and fault current. The controller should also enforce defined states on the address and enable lines to prevent unintended routing during reset or startup.

تجویز کردہ پروڈکٹس کا خلاصہ

DG407DJZ DG407-family differential multiplexer in the same application class استعمال ہوتا ہے: Multichannel Data Acquisition, Audio Signal Routing, Communication Signal Multiplexing, Sample-and-Hold Signal Conditioning, Guidance and Control Systems DG406DJ Same-family 16:1 multiplexer for design comparison استعمال ہوتا ہے: Multichannel Data Acquisition, Test and Measurement Systems, Sample-and-Hold Signal Conditioning DG406DJ+ Analog Devices استعمال ہوتا ہے: Audio Signal Routing, Communication Signal Multiplexing, Guidance and Control Systems DG406DJZ-E3 28-pin PDIP ordering alternative for comparative sourcing استعمال ہوتا ہے: Test and Measurement Systems
What is the DG406DJZ and what does it do?
The DG406DJZ is a single 16:1 CMOS analog multiplexer with 100 ohm maximum on-state resistance in a 28-pin PDIP package. It routes one of 16 analog inputs to a common output using four binary select inputs. According to the Renesas DG406 and DG407 datasheet, the device includes 16 analog switches, TTL- and CMOS-compatible decoding, an enable input, and an internal voltage reference for logic thresholds.
What is the operating voltage of DG406DJZ?
The DG406DJZ supply-voltage limits must be taken from the electrical-characteristics table in the Renesas DG406 and DG407 datasheet. The distributor description identifies the part as a 16:1 CMOS analog switch with 100 ohm on-state resistance, but it does not state the operating supply range. Confirm the positive and negative rail limits, input signal range, and enable-pin states before applying power or routing external analog voltages.
Where can I download the DG406DJZ datasheet PDF?
The official DG406 and DG407 datasheet is available from Renesas at https://www.renesas.com/en/document/dst/dg406-dg407-datasheet. It covers the DG406DJZ monolithic CMOS analog multiplexer, including its 16 analog switches, address decoding, enable control, logic-threshold reference, application circuits, and electrical characteristics. Use the package-specific pin description and maximum-rating tables when planning a PCB or replacing an installed part.
Where can I find the DG406DJZ pinout?
The DG406DJZ pin assignment is shown in the pin-configuration section of the Renesas DG406 and DG407 datasheet. The component uses a 28-pin PDIP package with pins distributed across both sides of the device. Because the package drawing and truth table must be interpreted together, use the datasheet diagram to identify the common, select inputs, enable input, and channel terminals rather than relying on a generic 28-pin layout.
Can DG406DJ replace DG506A or DG507A devices?
Yes, the DG406 family is designed as a drop-in replacement for the popular DG506A and DG507A series. According to the Renesas DG406 and DG407 datasheet, the design retains the 16-channel CMOS switching architecture, TTL- and CMOS-compatible digital decoding, logic-threshold voltage reference, and enable input. A board revision should still verify signal-range, timing, and absolute-maximum-rating changes before production use.
Is DG406DJZ suitable for data acquisition?
The DG406DJZ is suitable for data-acquisition systems that must route multiple analog inputs to one measurement channel. Its 16:1 configuration reduces the number of physical input connections, while the enable input allows several multiplexers to share control and output arrangements. The 100 ohm maximum on-state resistance is an important consideration when the source impedance, ADC acquisition time, and allowable settling error are known.
What is the difference between DG406DJZ and DG406DJ?
The DG406DJZ is a Renesas Electronics 28-pin PDIP version of the DG406 16:1 analog multiplexer, while DG406DJ is listed as a Vishay Siliconix 28-pin PDIP version. Both are presented with the same 16:1 configuration and 100 ohm on-state resistance. Their exact supply-voltage, timing, temperature, and qualification details should be compared in their respective manufacturer datasheets before substitution.
Can DG406DJ+ replace DG406DJZ?
The DG406DJ+ can be considered for replacement only after its manufacturer datasheet confirms the same 28-pin PDIP pinout, channel count, logic levels, enable behavior, and electrical limits. Cross-reference information identifies the DG406 family as a drop-in replacement for older DG506A and DG507A devices, but it does not remove the need to verify timing and maximum-rating compatibility. The DG406DJ+ is the better candidate when its published ratings align with the target design.
What is the best drop-in replacement for DG406DJZ?
The DG406DJ from Vishay Siliconix is a documented 28-pin PDIP alternative with a 16:1 configuration and 100 ohm maximum on-state resistance. Renesas DG406DJ+ and other DG406 package variants may also fit legacy boards, but their electrical specifications must be checked before approval. For a production redesign, use the alternative whose complete datasheet matches the required supply range, signal range, timing, temperature range, and lifecycle expectations.
When should I choose DG406DJZ over a smaller analog switch?
Choose the DG406DJZ when a design must select among 16 analog sources using digital addressing and can accommodate a 28-pin PDIP footprint. A smaller analog switch may suit applications with fewer channels, but it cannot provide the same 16:1 routing capability or the DG406 family's TTL/CMOS-compatible decoder and enable architecture. The decision should also account for the 100 ohm maximum on-state resistance and the source impedance at the selected node.
Where can I buy DG406DJZ and check its current lead time?
Use the Request a Quote form on this page to ask about DG406DJZ availability, current lead time, order quantity, and the appropriate 28-pin PDIP packaging option. The part is identified as a 28-pin PDIP from Renesas Electronics. Quote requests allow the current channel, lifecycle status, and production quantity to be checked without relying on stale stock or pricing information.
What is the price of DG406DJZ?
Current DG406DJZ commercial terms should be requested through the Request a Quote form on this page. The form allows quantity, package format, delivery expectations, and traceability requirements to be included in the request. This avoids presenting an outdated family price as a current quote for the exact Renesas Electronics DG406DJZ 28-pin PDIP ordering code.
Is DG406DJZ in stock?
Current DG406DJZ stock status should be confirmed through the Request a Quote form on this page by entering the required quantity and delivery schedule. Because inventory can change by package configuration, order quantity, and manufacturing status, a general product-page statement would not reliably answer a stock question. The form routes the request for an exact DG406DJZ fulfillment response.
How does the enable input affect DG406DJZ operation?
The DG406DJZ enable input provides device-level control in addition to its four select inputs. According to the Renesas DG406 and DG407 datasheet, the enable function is intended for systems in which several multiplexers are present and individual devices must be selected or isolated. Designers should use the datasheet truth table to establish the required logic state and avoid leaving an analog node in an unintended active state.
What are the key specifications of DG406DJZ that engineers should know?
The principal DG406DJZ specifications are a single 16:1 CMOS analog multiplexer, 16 switched channels, 100 ohm maximum on-state resistance, TTL- and CMOS-compatible decoding, an enable input, and a 28-pin PDIP package. The Renesas DG406 and DG407 datasheet also describes the internal logic-threshold voltage reference and the family's compatibility with DG506A and DG507A devices. Supply limits, timing, and temperature ratings should be read directly from the manufacturer specifications.

کے لیے انجینئرنگ ریفرنس ڈیٹا DG406DJZ — موازنہ، ڈیزائن رہنمائی، اور تعمیل کی معلومات۔

انتخاب کی گائیڈ

Choose the DG406DJZ when a new or legacy design requires a single 16:1 analog multiplexer in a 28-pin PDIP footprint, TTL- and CMOS-compatible address decoding, and device-level enable control. It is especially appropriate for data acquisition, test equipment, audio routing, and control systems where one shared analog node must reach multiple sources. Select the Vishay DG406DJ when its manufacturer-specific electrical ratings, qualification, and lifecycle are better suited to the board, provided the pinout and timing are verified. The Renesas DG406DJ+ is a natural same-family candidate for a modern replacement, but its plus-marked ordering code should be checked for specification revisions. The Analog Devices DG406DJ and legacy Intersil DG406DJZ options can support board-reuse strategies, although each requires direct comparison against the current production datasheet. In every case, verify supply voltage, allowable analog signal range, enable truth table, channel matching, and on-resistance effects before releasing a PCB revision.

متبادلات کے ساتھ موازنہ

پیرامیٹر یہ پروڈکٹ DG406DJ DG406DJ+ DG406DJZ-E3 DG406DJ DG406DJZ
Brand Renesas Electronics Vishay Intertechnology Renesas Electronics Vishay Intertechnology Analog Devices Intersil Corporation
Package 28-pin PDIP 28-pin PDIP - same 28-pin PDIP - same 28-pin PDIP - same 28-pin PDIP - same 28-pin PDIP - same
Multiplexer Configuration 16:1 16:1 16:1 16:1 16:1 16:1
Number of Circuits 1 circuit 1 circuit 1 circuit 1 circuit 1 circuit 1 circuit
Number of Channels 16 channels 16 channels 16 channels 16 channels 16 channels 16 channels

اہم امتیازی خصوصیات

  • Maintains the established 28-pin PDIP routing architecture (بمقابلہDG406DN+)
  • Provides the full 16-channel single-ended mux function (بمقابلہDG407DJZ)
  • Uses a standard 100 ohm maximum on-state resistance (بمقابلہDG406DJ)

ڈیزائن نوٹس

Route the common analog node and selected channel traces as short, direct paths, and place the DG406DJZ near the source or destination that imposes the tighter impedance and settling requirements. Keep the four select inputs and enable line away from sensitive analog traces because their switching transitions can couple into the multiplexed node. A continuous ground plane and a short return path for digital control signals will reduce susceptibility to channel crosstalk.

Do not select a replacement from package appearance alone. Confirm the complete 28-pin PDIP pin assignment, 16:1 configuration, logic levels, enable truth table, supply limits, analog signal range, and maximum on-state resistance. The DG406DJ and DG406DJ+ share the principal architecture, but manufacturer-specific timing and absolute-maximum-rating differences can still affect an existing board revision.

Include the 100 ohm maximum on-state resistance, source impedance, capacitance, and acquisition time when evaluating settling error. For a high-impedance sensor or ADC input, the mux resistance can dominate the charging network and cause incomplete settling between channel changes. Increase the available acquisition interval or use a lower-impedance buffer, then verify the result against the manufacturer's switching and channel-matching characteristics.

Define valid logic states for all select and enable inputs during reset, power-up, and firmware faults. Floating control inputs can create unintended channel transitions or uncertain device-enable behavior. Use the datasheet truth table, pull resistors where appropriate, and controller initialization that writes a known address and enable state before the analog system begins acquisition.

تعمیل کی معلومات

RoHS
Compliant
REACH
Unknown
AEC-Q100
Not Applicable
لیڈ فری
Yes
ہیلوجن فری
Unknown
کنفلیکٹ منرلز
Unknown

The DG406DJZ is identified as lead free and RoHS compliant. It is not identified as an AEC-Q100 qualified automotive component.

ڈیٹا کی تصدیق کی تاریخ: 2026-11-16 — ڈیٹا XAIPART کی کمپوننٹ انجینئرنگ ٹیم کے ذریعے تصدیق شدہ اور ترتیب شدہ

متعلقہ تلاشیں

DG406DJZ datasheet DG406DJZ datasheet pdf DG406DJZ pinout DG406DJZ equivalent DG406DJZ replacement DG406DJZ cross reference DG406DJZ vs DG406DJ Renesas DG406DJZ DG406 16:1 analog multiplexer DG406DJZ 28-pin PDIP DG406DJZ data acquisition DG406DJZ price DG406DJZ stock

متعلقہ اجزاء اور اصطلاحات

Renesas Electronics DG406DJZ DG406 DG406DJ DG406DJ+ DG406DJZ-E3 DG407 DG506A DG507A Vishay Intertechnology Analog Devices Intersil Corporation CMOS analog multiplexer analog switch multiplexer interface IC semiconductor 16:1 multiplexing TTL-compatible logic CMOS-compatible logic on-state resistance enable input 28-pin PDIP through-hole package data acquisition sample-and-hold RoHS lead-free electronics
فوری کوٹ RFQ
مکمل تفصیلات بھریں — ہماری سیلز ٹیم 24 گھنٹوں میں جواب دے گی
پارٹ نمبر مینوفیکچرر پیکج QTY ہدف قیمت کل رقم
✓
کوٹ جمع ہو گیا!

ہم 24 گھنٹوں کے اندر آپ کے ای میل کا جواب دیں گے

1
RFQ جمع ہو گیا
2
کوٹ موصول ہو گیا
3
آرڈر دے دیا گیا
4
ادائیگی
5
بھیج دیا گیا
6
ڈیلیور شدہ
RFQ تفصیلات دیکھیں