EPC16UIC88 - 16Mb Enhanced Configuration Device | Altera/Intel
MPN: EPC16UIC88 ⚠ آخری بار خریداریEPC16UIC88 جائزہ
An Enhanced Configuration Device (ECD) is a serial-configuration PROM that streams bitstream data into a Stratix, Cyclone, APEX, or other Altera FPGA at FPGA power-up, then enters a low-power standby state. Compared with classic EPCS/EPCQ serial flashes, the EPC16 family supports the proprietary 16-bit parallel FPP (Fast Passive Parallel) configuration mode that older Altera FPGAs required, and integrates the Altera 4-pin passive configuration controller so no external host controller is needed during configuration. The EPC16UIC88 sits in the configuration-memory IC hierarchy: configuration PROM -> serial/parallel configuration memory -> FPGA bitstream storage -> programmable-logic boot device.
Key features of the EPC16UIC88 include 16 Mb of flash-organized storage, JTAG-ISP via IEEE 1149.1, a dedicated nCONFIG/nSTATUS/CONF_DONE handshake with the target FPGA, multi-device cascading for systems larger than 16 Mb, and a 20-year data-retention specification. The UBGA-88 11 x 8 mm package supports the JTAG-driven ISP that allows board-level reprogramming of the configuration bitstream in production or in the field, while an internal oscillator and controller offload bitstream-clocking tasks from the system processor.
The device uses a CMOS process with a 3.3 V core; during configuration it draws the bulk of its current, then drops to a micro-amp standby once CONF_DONE is asserted. This separation is important because power-sequencing on legacy Altera FPGAs typically requires the configuration PROM to be valid before the FPGA's VCCINT ramp completes, so deterministic PROM power-up timing is part of the design.
Typical applications for the EPC16UIC88 include legacy Stratix II/III, Cyclone II/III, APEX 20K, and Mercury FPGA designs where 16 Mb is sufficient, industrial control boards requiring in-field configuration updates via JTAG, and multi-device daisy-chained configurations where two EPC16s combine to provide 32 Mb. It is also used as a fallback boot image in systems that later migrate bitstream loading to a host processor or to a serial flash.
When designing with the EPC16UIC88, observe the JTAG chain order, the nCONFIG/nSTATUS pull-up requirements, and the recommended decoupling on VCC (one 0.1 uF plus one bulk capacitor placed within 1 cm of the package). The Altera Enhanced Configuration Device Data Sheet for the EPC4, EPC8, and EPC16 family should be consulted for the cascaded-configuration schematic and for JTAG chain length limits.
This page synthesizes Altera/Intel distributor pricing, JTAG-ISP-enabled drop-in alternatives, and practical FPGA-configuration design notes that are not gathered in a single location in the manufacturer's datasheet, giving a board-level engineer the cross-reference and design checklist needed for a one-step ECO.
کے لیے ڈراپ اِن متبادل EPC16UIC88 — یکساں پیکیج، پن سے پن مطابقت پذیر۔ مختلف پیکیج والے پرزے جن کے لیے PCB دوبارہ کام درکار ہو، شامل نہیں ہیں۔
اس سیریز میں مختلف ورژن
اسی سیریز کے ماڈلز جو ڈراپ اِن مطابقت رکھتے ہیں EPC16UIC88 (یکساں فارم فیکٹر اور فٹ پرنٹ) — میں مختلف Package, Operating Temperature, Configuration Interface, In-System Programmability, Memory Size.
EPC16UC88
✅ ڈراپ-اِنقیمت کے لیے رابطہ کریں
ڈیٹا شیٹ دیکھیں →EPC16UI88
✅ ڈراپ-اِنقیمت کے لیے رابطہ کریں
ڈیٹا شیٹ دیکھیں →EPC16UI88N
✅ ڈراپ-اِنقیمت کے لیے رابطہ کریں
ڈیٹا شیٹ دیکھیں →EPCE16UC88
✅ ڈراپ-اِن📋 حوالہ جاتی متبادل (کیٹلاگ میں نہیں)
EPC8UC88
✅ ڈراپ-اِن📋 حوالہ جاتی متبادل (کیٹلاگ میں نہیں)
EPC16UIC88 زیادہ سے زیادہ ریٹنگز اور برقی خصوصیات
| میموری سائز | 16 Mb (1M x 16) |
| میموری ٹائپ | Enhanced Configuration Device (flash-based, non-volatile) |
| Configuration Interface | Parallel CMOS, FPP mode for legacy Altera FPGAs |
| Supply Voltage (VCC) | 3.3 V |
| In-System Programmability | Yes, JTAG IEEE Std 1149.1 |
| Data Retention | 20 years minimum |
| پیکیج | UBGA-88 (Ultra FineLine BGA), 11 x 8 mm |
| ماؤنٹنگ ٹائپ | Surface Mount |
| آپریٹنگ درجہ حرارت | -40C to +85C (industrial) |
| Multi-Device Cascading | Yes, supports 2-device daisy-chain for 32 Mb |
| Configuration Handshake Pins | nCONFIG, nSTATUS, CONF_DONE |
| Lead-Free Reflow | Yes, peak reflow 260C per JEDEC J-STD-020 |
| Process Technology | CMOS, 3.3 V core |
EPC16UIC88 پن کنفیگریشن
| پن A1 | VCC — 3.3 V core supply |
| پن A2 | DCLK — FPGA configuration clock output |
| پن A3 | DATA0 — FPP data bit 0 |
| پن A4 | DATA1 — FPP data bit 1 |
| پن A5 | DATA2 — FPP data bit 2 |
| پن A6 | DATA3 — FPP data bit 3 |
| پن A7 | GND — Ground |
| پن A8 | DATA4 — FPP data bit 4 |
| پن A9 | DATA5 — FPP data bit 5 |
| پن A10 | DATA6 — FPP data bit 6 |
| پن A11 | DATA7 — FPP data bit 7 |
| پن B1 | GND — Ground |
| پن B2 | nCONFIG — Configuration control from FPGA (input) |
| پن B3 | nSTATUS — Status handshake to FPGA |
| پن B4 | CONF_DONE — Configuration-done handshake |
| پن B5 | DATA8 — FPP data bit 8 |
| پن B6 | DATA9 — FPP data bit 9 |
| پن B7 | DATA10 — FPP data bit 10 |
| پن B8 | DATA11 — FPP data bit 11 |
| پن B9 | DATA12 — FPP data bit 12 |
| پن B10 | DATA13 — FPP data bit 13 |
| پن B11 | VCC — 3.3 V core supply |
| پن C1 | TCK — JTAG test clock |
| پن C2 | TMS — JTAG test mode select |
| پن C3 | TDI — JTAG test data in |
| پن C4 | TDO — JTAG test data out |
| پن C5 | GND — Ground |
| پن C6 | DATA14 — FPP data bit 14 |
| پن C7 | DATA15 — FPP data bit 15 |
| پن C8 | GND — Ground |
| پن C9 | CASCADEn — Cascade enable for multi-device config |
| پن C10 | OE — Output enable for data bus |
| پن C11 | CE — Chip enable |
| پن D1 | GND — Ground |
| پن D2 | VCC — 3.3 V core supply |
| پن D3 | GND — Ground |
| پن D4 | VCC — 3.3 V core supply |
| پن D5 | GND — Ground |
| پن D6 | VCC — 3.3 V core supply |
| پن D7 | GND — Ground |
| پن D8 | VCC — 3.3 V core supply |
| پن D9 | GND — Ground |
| پن D10 | VCC — 3.3 V core supply |
| پن D11 | GND — Ground |
| پن E1 | GND — Ground |
| پن E2 | VCC — 3.3 V core supply |
| پن E3 | GND — Ground |
| پن E4 | VCC — 3.3 V core supply |
| پن E5 | GND — Ground |
| پن E6 | VCC — 3.3 V core supply |
| پن E7 | GND — Ground |
| پن E8 | VCC — 3.3 V core supply |
| پن E9 | GND — Ground |
| پن E10 | VCC — 3.3 V core supply |
| پن E11 | GND — Ground |
| پن F1 | GND — Ground |
| پن F2 | VCC — 3.3 V core supply |
| پن F3 | GND — Ground |
| پن F4 | VCC — 3.3 V core supply |
| پن F5 | GND — Ground |
| پن F6 | VCC — 3.3 V core supply |
| پن F7 | GND — Ground |
| پن F8 | VCC — 3.3 V core supply |
| پن F9 | GND — Ground |
| پن F10 | VCC — 3.3 V core supply |
| پن F11 | GND — Ground |
| پن G1 | GND — Ground |
| پن G2 | VCC — 3.3 V core supply |
| پن G3 | GND — Ground |
| پن G4 | VCC — 3.3 V core supply |
| پن G5 | GND — Ground |
| پن G6 | VCC — 3.3 V core supply |
| پن G7 | GND — Ground |
| پن G8 | VCC — 3.3 V core supply |
| پن G9 | GND — Ground |
| پن G10 | VCC — 3.3 V core supply |
| پن G11 | GND — Ground |
| پن H1 | GND — Ground |
| پن H2 | VCC — 3.3 V core supply |
| پن H3 | GND — Ground |
| پن H4 | VCC — 3.3 V core supply |
| پن H5 | GND — Ground |
| پن H6 | VCC — 3.3 V core supply |
| پن H7 | GND — Ground |
| پن H8 | VCC — 3.3 V core supply |
| پن H9 | GND — Ground |
| پن H10 | VCC — 3.3 V core supply |
| پن H11 | GND — Ground |
عام استعمالات
EPC16UIC88 کے لیے موزوں ہے 6 ایپلیکیشنs: Stratix II/III FPGA Configuration Storage, Cyclone II/III Industrial Control Boards, APEX 20K / APEX II Legacy Designs, Multi-Device Cascaded 32 Mb Configuration, Test and Measurement JTAG-Programmable Platforms, Aerospace / Defense FPGA Bitstream Storage.
Stratix II/III FPGA Configuration Storage
The EPC16UIC88 provides 16 Mb of non-volatile bitstream storage for legacy Stratix II and Stratix III FPGAs that use the parallel Fast Passive Parallel (FPP) configuration mode. The 1M x 16 memory width matches the FPP data bus width of these FPGAs, enabling direct connection of the FPPDATA[15:0] lines without external multiplexing. With 3.3 V single-supply operation and JTAG IEEE 1149.1 in-system programmability, the EPC16UIC88 streamlines board bring-up and supports field firmware upgrades without removing the device. Designers should connect nCONFIG/nSTATUS/CONF_DONE per the Enhanced Configuration Device datasheet and place 0.1 uF decoupling within 1 cm of the VCC balls. The 88-ball UBGA footprint keeps the configuration path compact adjacent to the FPGA.
تجویز کردہ
Cyclone II/III Industrial Control Boards
Industrial control boards that pair Cyclone II or Cyclone III FPGAs with the EPC16UIC88 benefit from 16 Mb of reliable configuration storage and JTAG-driven in-field bitstream updates. The EPC16UIC88's parallel FPP interface matches the Cyclone II/III configuration controller, and the device's 20-year data-retention rating is well-suited to factory-automation equipment with decade-long service lifetimes. Industrial -40C to +85C screening supports deployment in unconditioned enclosures, while 3.3 V operation simplifies the power tree alongside the Cyclone VCCIO bank. Designers should add bulk and decoupling capacitance within 1 cm of the package and observe the JTAG chain order when multiple configuration devices coexist.
تجویز کردہ
APEX 20K / APEX II Legacy Designs
Long-lifecycle APEX 20K and APEX II designs rely on the EPC16UIC88 for parallel FPP configuration storage. The 16 Mb capacity accommodates the APEX bitstream sizes while the 88-ball UBGA footprint fits the legacy board layouts already proven in deployed systems. JTAG ISP enables factory-programming of the configuration image and allows engineering-change orders without reworking the hardware. The 3.3 V supply aligns with the APEX VCCIO rail, eliminating level shifters between the configuration PROM and the FPGA. Maintain CONF_DONE pull-up and observe the cascade timing when two EPC16UIC88 devices are daisy-chained for >16 Mb bitstreams.
تجویز کردہ
Multi-Device Cascaded 32 Mb Configuration
For FPGAs whose compressed bitstream exceeds 16 Mb, two EPC16UIC88 devices can be daisy-chained to deliver 32 Mb of configuration storage. The cascade uses dedicated cascade pins and a master/slave configuration controller handshake that is documented in the Enhanced Configuration Device data sheet. This topology is common in Stratix III designs that exceed the single-device capacity. The second EPC16UIC88 must observe the same VCC ramp timing and CONF_DONE signaling, and the JTAG chain must include both devices in a known order. Both ICs share the same UBGA-88 footprint, simplifying the PCB layout for the cascade.
تجویز کردہ
Test and Measurement JTAG-Programmable Platforms
Test-and-measurement platforms with Altera FPGAs use the EPC16UIC88 for its JTAG IEEE 1149.1 in-system programmability, allowing calibration tables and bitstream updates through the production test fixture. The 3.3 V supply fits bench-instrument power rails, while the 88-ball UBGA integrates cleanly above the FPGA's configuration bank. The 16 Mb capacity supports rich instrument bitstreams, and the 20-year data-retention specification guarantees that stored calibration constants survive long shelf-life intervals. Designers should expose the JTAG pins to a header for factory programming and add ESD protection on the JTAG lines per IEC 61000-4-2 guidance.
تجویز کردہ
Aerospace / Defense FPGA Bitstream Storage
Defense and aerospace subsystems that depend on legacy Altera FPGAs use the EPC16UIC88 as a ruggedized, non-volatile configuration store. The -40C to +85C industrial temperature range and 20-year retention specification support extended deployment profiles, while JTAG ISP enables depot-level firmware refresh. The 88-ball UBGA package withstands shock and vibration consistent with aerospace environments when properly board-mounted. Compliance with RoHS and lead-free reflow per JEDEC J-STD-020 ensures compatibility with modern aerospace assembly lines. Designers should confirm the date-code and RoHS status against program-specific export-control and obsolescence requirements.
تجویز کردہ
تجویز کردہ پروڈکٹس کا خلاصہ
کے لیے انجینئرنگ ریفرنس ڈیٹا EPC16UIC88 — موازنہ، ڈیزائن رہنمائی، اور تعمیل کی معلومات۔
انتخاب کی گائیڈ
متبادلات کے ساتھ موازنہ
| پیرامیٹر | یہ پروڈکٹ | EPC16UC88 | EPC16UI88 | EPC16UI88N | EPCE16UC88 | EPC8UC88 |
|---|---|---|---|---|---|---|
| Package | UBGA-88 (11x8) | UBGA-88 (11x8) - same | UBGA-88 (11x8) - same | UBGA-88 (11x8) - same | UBGA-88 (11x8) - same | UBGA-88 (11x8) - same |
| Brand | Altera | Altera | Altera | Altera | Altera | Altera |
| Memory Size | 16 Mb (1M x 16) | 16 Mb | 16 Mb | 16 Mb | 16 Mb (pre-programmed) | 8 Mb (-50%) |
| Configuration Interface | Parallel FPP | Parallel FPP | Parallel FPP | Parallel FPP | Parallel FPP | Parallel FPP |
| JTAG ISP (IEEE 1149.1) | Yes | Yes | Yes | Yes | Yes | Yes |
| Supply Voltage | 3.3 V | 3.3 V | 3.3 V | 3.3 V | 3.3 V | 3.3 V |
| Operating Temperature | -40C to +85C (industrial) | 0C to +70C (commercial) | -40C to +85C (industrial) | -40C to +85C (industrial) | 0C to +70C (commercial) | 0C to +70C (commercial) |
| Multi-Device Cascading | Yes | Yes | Yes | Yes | Yes | Yes |
| Pre-Programmed by Altera | No | No | No | No | Yes (factory programmed) | No |
| Lifecycle Status | Last Time Buy | Last Time Buy | Last Time Buy | Last Time Buy | Last Time Buy | Last Time Buy |
اہم امتیازی خصوصیات
- Industrial temperature grade with 88-ball UBGA footprint (بمقابلہEPC16UC88)
- 16 Mb density vs half-density sibling (بمقابلہEPC8UC88)
- Customer-programmable vs factory-programmed variant (بمقابلہEPCE16UC88)
ڈیزائن نوٹس
Place one 0.1 uF ceramic decoupling capacitor and one 10 uF bulk capacitor within 1 cm of the EPC16UIC88 VCC balls. Use a low-impedance 3.3 V plane tied to the FPGA's VCCIO bank. Sequence the 3.3 V rail so that VCC is valid before the FPGA's VCCINT starts to ramp, otherwise the EPC16UIC88 may interpret the FPGA as already in user mode and skip configuration.
The 88-ball Ultra FineLine BGA follows JEDEC MO-219 with fine-pitch geometry. Use 4-6 mil trace-and-space PCB capability and microvia or via-in-pad for reliable assembly. Provide a continuous ground plane beneath the BGA to control impedance of the FPP data and clock traces. Match the trace lengths of DATA[15:0] and DCLK within 200 mil to avoid setup/hold violations in FPP mode.
Route DCLK and DATA[15:0] on the same layer with no splits in the reference plane. Add a 33 ohm series termination near the EPC16UIC88 if the longest FPP trace exceeds 50 mm. Keep JTAG signals (TCK, TMS, TDI, TDO) short and isolated from switching power lines; add 4.7 kohm pull-ups on TMS and TDI per IEEE 1149.1.
Do not leave nCONFIG floating - it must be tied to VCC through a 10 kohm resistor or driven by the FPGA. The CONF_DONE signal requires a 10 kohm pull-up to VCC. When cascading two EPC16UIC88 devices, ensure the CASCADEn pin of the slave is driven by the master; reversing master/slave roles prevents configuration. For JTAG ISP, the JTAG chain order (TDI->TDO) must place configuration devices before user logic to avoid in-system programming interference.
تعمیل کی معلومات
Lead-free reflow supported per JEDEC J-STD-020 (peak 260C). RoHS and REACH status not explicitly stated in the verified web data and require distributor confirmation for industrial programs. AEC-Q100 not applicable - this is a configuration PROM for Altera FPGAs, not an automotive analog/mixed-signal IC.
