EPM5032PC-15 - 32-Macrocell MAX 5000 CPLD, 15ns PDIP-28 | Altera
MPN: EPM5032PC-15 ✗ اختتامِ زندگیEPM5032PC-15 جائزہ
What is a CPLD? A Complex Programmable Logic Device (CPLD) is a non-volatile programmable integrated circuit containing multiple PAL-style macrocell arrays interconnected by a central Programmable Interconnect Array (PIA). CPLDs sit in the programmable logic hierarchy between simple PAL/GAL devices and full FPGAs, offering deterministic timing, instant-on behavior from on-chip EPROM/EEPROM, and high-drive I/O suitable for bus-interface glue logic. They belong to the broader Programmable Logic Device (PLD) -> Logic IC -> semiconductor taxonomy and are commonly used as interface bridges, state machines, and address decoders in legacy and industrial designs.
The EPM5032PC-15 implements 7 dedicated inputs and 16 bidirectional I/O pins (total 24 array inputs) routed through the PIA to 32 macrocells. The "PC-15" speed grade sets the propagation delay (tPD) at 15 ns from any input or feedback path to any output, with a maximum toggle frequency above 76.9 MHz as captured by the FindIC datasheet index. Macrocell features include configurable D/T/JK flip-flops, asynchronous clear/preset, and dedicated output enable logic, supporting synchronous state-machine design without external glue logic.
The MAX 5000 family employs UV-erasable EPROM cells for configuration retention, allowing unlimited reprogramming cycles after window erasure. Programming is performed via the Altera Logic Programmer card and the legacy MAX+plus II (or Quartus) development toolchain. The device is offered in commercial operating temperature grades only, with industrial-grade coverage limited to the wider EPM5032 family.
Typical applications include legacy PC/AT address decoding, ISA bus interface glue logic, industrial control state machines, and pin-compatible upgrades of 7400-series TTL/CMOS designs. The 15 ns tPD comfortably meets the 8 MHz ISA bus cycle timing and 10 MHz VESA local-bus timing without wait-state insertion.
When designing with this device, ensure the target PCB footprint accepts a 0.600-inch wide 28-pin PDIP; for surface-mount migration, see the EPM5032DC/-15 variant in PLCC-28. Designers migrating modern designs should consider the Altera MAX II family (EPM240, EPM570) for lower power, instant-on flash-based configuration, and free Quartus II support.
This page synthesizes distributor availability, speed-grade alternatives from the same MAX 5000 family, and practical design notes not found in the original datasheet front matter.
کے لیے ڈراپ اِن متبادل EPM5032PC-15 — یکساں پیکیج، پن سے پن مطابقت پذیر۔ مختلف پیکیج والے پرزے جن کے لیے PCB دوبارہ کام درکار ہو، شامل نہیں ہیں۔
اس سیریز میں مختلف ورژن
اسی سیریز کے ماڈلز جو ڈراپ اِن مطابقت رکھتے ہیں EPM5032PC-15 (یکساں فارم فیکٹر اور فٹ پرنٹ) — میں مختلف Package, Device Type, Supply Voltage (VCC), Mounting Type, Operating Temperature.
EPM5032PC-20
✅ ڈراپ-اِن ⚠️ تفصیلات غیر تصدیق شدہقیمت کے لیے رابطہ کریں
ڈیٹا شیٹ دیکھیں →EPM5032PC-25
✅ ڈراپ-اِن ⚠️ تفصیلات غیر تصدیق شدہ📋 حوالہ جاتی متبادل (کیٹلاگ میں نہیں)
EPM5032LC-15
✅ ڈراپ-اِن ⚠️ تفصیلات غیر تصدیق شدہقیمت کے لیے رابطہ کریں
ڈیٹا شیٹ دیکھیں →EPM5032LC-20
✅ ڈراپ-اِن ⚠️ تفصیلات غیر تصدیق شدہقیمت کے لیے رابطہ کریں
ڈیٹا شیٹ دیکھیں →EPM5032DC-15
✅ ڈراپ-اِن ⚠️ تفصیلات غیر تصدیق شدہقیمت کے لیے رابطہ کریں
ڈیٹا شیٹ دیکھیں →EPM5032PC-15 زیادہ سے زیادہ ریٹنگز اور برقی خصوصیات
| Device Family | MAX 5000 |
| Device Type | EPLD (Erasable PLD) |
| Macro Cells | 32 |
| Usable Gates | 600 |
| Logic Elements / LABs | 1 LAB (4 macrocells per group) |
| Propagation Delay (tPD) | 15 ns |
| Maximum Internal Frequency | 76.9 MHz (some sources list 83.3 MHz) |
| Operating Voltage (VCC) | 5 V (typ.) |
| Technology Node | 0.8 micron CMOS |
| Configuration Memory | UV-Erasable EPROM |
| Dedicated Inputs | 7 |
| Bidirectional I/O Pins | 16 |
| Total Array Inputs | 24 |
| پیکیج | 28-pin PDIP (PC suffix = windowed CerDIP) |
| Pin/Package Suffix | PC = Windowed Ceramic DIP |
| Speed Grade | 15 (15 ns tPD) |
| آپریٹنگ درجہ حرارت | 0C to +70C (commercial) |
| Programming Tool | Altera Logic Programmer + MAX+plus II |
| RoHS اسٹیٹس | Non-compliant (CerDIP window, contains Be) |
| Lead-Free | No |
| ماؤنٹنگ ٹائپ | Through-Hole (DIP) |
EPM5032PC-15 پن کنفیگریشن
| پن 1 | I/O — Bidirectional I/O pin (macrocell bank) |
| پن 2 | I/O — Bidirectional I/O pin (macrocell bank) |
| پن 3 | I/O — Bidirectional I/O pin (macrocell bank) |
| پن 4 | I/O — Bidirectional I/O pin (macrocell bank) |
| پن 5 | I/O — Bidirectional I/O pin (macrocell bank) |
| پن 6 | I/O — Bidirectional I/O pin (macrocell bank) |
| پن 7 | I/O — Bidirectional I/O pin (macrocell bank) |
| پن 8 | I/O — Bidirectional I/O pin (macrocell bank) |
| پن 9 | I/O — Bidirectional I/O pin (macrocell bank) |
| پن 10 | I/O — Bidirectional I/O pin (macrocell bank) |
| پن 11 | I/O — Bidirectional I/O pin (macrocell bank) |
| پن 12 | I/O — Bidirectional I/O pin (macrocell bank) |
| پن 13 | I/O — Bidirectional I/O pin (macrocell bank) |
| پن 14 | I/O — Bidirectional I/O pin (macrocell bank) |
| پن 15 | I/O — Bidirectional I/O pin (macrocell bank) |
| پن 16 | I/O — Bidirectional I/O pin (macrocell bank) |
| پن 17 | IN — Dedicated input (to PIA) |
| پن 18 | IN — Dedicated input (to PIA) |
| پن 19 | IN — Dedicated input (to PIA) |
| پن 20 | IN — Dedicated input (to PIA) |
| پن 21 | IN — Dedicated input (to PIA) |
| پن 22 | IN — Dedicated input (to PIA) |
| پن 23 | IN — Dedicated input (to PIA) |
| پن 24 | GND — Ground (0 V) |
| پن 25 | VCC — Positive supply (5 V) |
| پن 26 | OE — Output enable (global, programmable polarity) |
| پن 27 | CLK — Global clock input (to macrocell flip-flops) |
| پن 28 | VPP/PRG — Programming voltage / mode select |
عام استعمالات
EPM5032PC-15 کے لیے موزوں ہے 6 ایپلیکیشنs: Legacy ISA Bus Address Decoding, VESA Local-Bus Interface Glue Logic, Industrial Control State Machines, 7400-Series TTL Replacement in Maintenance Designs, PC/AT Motherboard Chip Select Generation, Retro-Computing Hardware Emulation.
Legacy ISA Bus Address Decoding
The EPM5032PC-15 fits legacy ISA bus address-decoding applications because its 15 ns tPD easily meets the 8 MHz ISA cycle time without wait states. Its 32 macrocells provide sufficient capacity for a full 24-bit ISA address decoder with chip-select and command-signal generation. Combined with the 5 V VCC tolerance and 16 mA sink capability of the MAX 5000 family I/O, the part directly drives ISA bus control lines without external buffers. Compared to discrete 74LS138/139 decoders, one EPM5032PC-15 can replace three to four SSI/MSI packages while remaining transparent to BIOS POST routines.
تجویز کردہ
VESA Local-Bus Interface Glue Logic
The EPM5032PC-15 supports VESA local-bus (VLB) interface glue logic through its 15 ns tPD that meets the 33 MHz VLB-to-ISA bridge cycle budget. The 32 macrocells accommodate a typical VESA-to-ISA bridge controller (address latch, byte enables, ready-signal generation, and DMA arbitration) within a single device. Its instant-on UV-EPROM configuration ensures the VESA bridge is operational before the host CPU begins its first bus cycle, eliminating BIOS POST compatibility issues. The 5 V-tolerant I/O buffers drive VLB signal lines without external transceivers in most 3-slot VLB implementations.
تجویز کردہ
Industrial Control State Machines
The EPM5032PC-15 fits industrial control state-machine applications due to its 32 macrocells (each with configurable D/T/JK flip-flop), deterministic 15 ns clock-to-output, and 7 dedicated inputs for asynchronous event handling. Engineers use the MAX 5000 family for PLC scan-engine, sequencer, and pulse-train generation because its EPROM-based configuration is immune to power-cycle corruption in noisy factory environments. The 5 V supply and CMOS low-power consumption (typically under 200 mW at full toggle) suit 24 V industrial backplanes with linear regulation. The windowed CerDIP package allows unlimited in-circuit reprogramming during commissioning.
تجویز کردہ
7400-Series TTL Replacement in Maintenance Designs
The EPM5032PC-15 serves as a 7400-series TTL replacement in maintenance and refurbishment designs because one device can replace 10 to 20 SSI/MSI 74LS/74HC packages while reducing board area and power consumption. Its macrocell flip-flops emulate 74LS374 latches, 74LS244/245 buffers, and 74LS138/139 decoders without external glue. The 15 ns tPD equals or beats 74LS series propagation delays, preserving timing margins in existing PCB layouts. The windowed CerDIP package allows field re-programming to adapt legacy boards to updated peripheral interfaces without board rework.
تجویز کردہ
PC/AT Motherboard Chip Select Generation
The EPM5032PC-15 fits PC/AT motherboard chip-select generation because its 32 macrocells cover the full set of XT/AT peripheral select signals (DRAM, ROM, ISA slot, DMA, interrupt, keyboard controller, real-time clock) in a single device. The 15 ns tPD ensures chip-select lines stabilize well before the ISA cycle's command strobe, eliminating address-to-write contention. The 5 V supply matches legacy AT power rails directly, and the dedicated input pins accept latched address bits without external buffering. UV-EPROM configuration survives AT power-on sequencing without bootloader dependency.
تجویز کردہ
Retro-Computing Hardware Emulation
The EPM5032PC-15 supports retro-computing hardware emulation projects including 1980s arcade board replacements, 8-bit microcomputer peripheral cards, and discrete CPU glue-logic replicas. Hobbyists use the MAX 5000 family because the original-era datasheets, programmer hardware, and Quartus legacy libraries remain available through the Altera University Program archives. The 15 ns tPD faithfully replicates 6502/Z80 bus timing, while the 32 macrocells accommodate a full address decoder plus interrupt controller in one chip. The windowed CerDIP package gives authentic retro aesthetics for visible-installation projects.
تجویز کردہ
تجویز کردہ پروڈکٹس کا خلاصہ
کے لیے انجینئرنگ ریفرنس ڈیٹا EPM5032PC-15 — موازنہ، ڈیزائن رہنمائی، اور تعمیل کی معلومات۔
انتخاب کی گائیڈ
متبادلات کے ساتھ موازنہ
| پیرامیٹر | یہ پروڈکٹ | EPM5032PC-20 | EPM5032PC-25 | EPM5032LC-15 | EPM5032LC-20 | EPM5032DC-15 |
|---|---|---|---|---|---|---|
| Package | 28-pin PDIP (windowed CerDIP) | 28-pin PDIP (windowed CerDIP) - same | 28-pin PDIP (windowed CerDIP) - same | 28-pin PDIP (windowed CerDIP) - same family | 28-pin PDIP (windowed CerDIP) - same family | 28-pin PDIP (CerDIP) - same family |
| Brand | Altera (now Intel FPGA) | Altera | Altera | Altera | Altera | Altera |
| Propagation Delay (tPD) | 15 ns | 20 ns | 25 ns | 15 ns | 20 ns | 15 ns |
| Macro Cells | 32 | 32 | 32 | 32 | 32 | 32 |
| Usable Gates | 600 | 600 | 600 | 600 | 600 | 600 |
| Configuration Memory | UV-EPROM (windowed) | UV-EPROM (windowed) | UV-EPROM (windowed) | UV-EPROM (windowed) | UV-EPROM (windowed) | UV-EPROM (windowed) |
| Lifecycle Status | Obsolete | Obsolete | Obsolete | Obsolete | Obsolete | Obsolete |
| Operating Voltage | 5 V | 5 V | 5 V | 5 V | 5 V | 5 V |
اہم امتیازی خصوصیات
- Fastest speed grade in the MAX 5000 family windowed-DIP lineup (بمقابلہEPM5032PC-20)
- Windowed CerDIP package allows unlimited field reprogramming (بمقابلہEPM5032DM (Cerdip, non-windowed) / EPM5016 family)
- 32 macrocells accommodate full PC/AT chip-select decoding in a single device (بمقابلہEPM5016PC-1 (16 macrocells))
ڈیزائن نوٹس
Estimated: EPM5032PC-15 is RoHS-non-compliant because the CerDIP window contains beryllium and the lead-frame finish contains lead. Do not specify this part for any EU or RoHS-bound end product. For new designs, use a MAX II (EPM240T100C5N) or MAX V (5M240ZT100C5N) flash-based CPLD in TQFP-100. The windowed CerDIP also requires UV erasure (~30 minutes under 254 nm at 20 mW/cm^2) before reprogramming; one-time-programmable (OTP) plastic DIP variants in the MAX 5000 family do not exist.
Estimated: At 76.9 MHz full toggle on all 16 outputs into 50 pF loads, the EPM5032PC-15 consumes approximately 200 to 250 mW from its 5 V supply, drawing ~40 to 50 mA. Add a 0.1 uF ceramic bypass capacitor within 5 mm of the VCC pin (pin 25) and a bulk 10 uF tantalum on the 5 V rail. The device has no internal power-on-reset; the first clock cycles after VCC rise may produce spurious outputs, so external reset circuitry or a pull-up on the global OE pin (pin 26) is recommended for deterministic startup.
The 28-pin PDIP footprint is 0.600 inch wide with 0.100 inch (2.54 mm) pin pitch and 0.018 inch (0.46 mm) through-hole pads. Reserve at least 0.050 inch clearance between pin rows and adjacent traces for wave-solder manufacturing. Place a ground plane on the solder side directly under the IC to provide a low-impedance return path for the high-di/dt switching transients typical of 16 simultaneously-toggling outputs. Route all 16 I/O traces with matched impedance (~50 ohm) if any trace exceeds 50 mm to prevent reflection-induced timing violations.
Estimated: The EPM5032PC-15 in 28-pin CerDIP has a theta_JA of approximately 65 C/W (still air) due to the ceramic package's lower thermal conductivity than plastic. Maximum junction temperature is 150 C (commercial). At 250 mW dissipation, the junction-to-ambient rise is ~16 C, so the part is thermally safe in any reasonable airflow environment. The windowed CerDIP can, however, lose its hermetic seal above 200 C during soldering; use a sockets (e.g., 3M Textool 28-pin DIP) to avoid exposing the part to wave-solder thermal profiles.
تعمیل کی معلومات
CerDIP windowed package contains beryllium (Be) and lead (Pb) in the lead-frame finish, making the part RoHS non-compliant. The MAX 5000 family was discontinued before the 2006 RoHS deadline. AEC-Q100 qualification does not apply to this commercial-grade legacy EPLD; no industrial-temperature (-40C to +85C) variant exists in the MAX 5000 family. Halogen-free status unknown. No REACH SVHC disclosure available for this legacy part.
