EPM7160STI100-10N - MAX 7000S CPLD, 160 Macrocells, 100MHz, TQFP-100 | Intel/Altera
MPN: EPM7160STI100-10N ⚠ آخری بار خریداریEPM7160STI100-10N جائزہ
A CPLD (Complex Programmable Logic Device) is a non-volatile programmable logic device that combines the instant-on characteristics of PAL/GAL architectures with the high integration density of FPGAs. Within the broader taxonomy, a CPLD is a sub-category of programmable logic devices (PLDs), sitting above discrete 22V10 GALs in density and below modern low-power FPGAs. The MAX 7000S family sits in Altera's classic mid-density CPLD portfolio and is widely used as the 'glue logic' layer between processors, memories, and peripherals in 5V-tolerant systems.
Key differentiating features include a 5.0V core and I/O supply, 3.3V or 5V multi-voltage JTAG-based in-system programmability, 100 MHz internal performance, support for up to 84 user I/Os (some sources cite 104 I/Os for the TQFP-100 variant), and an industrial operating temperature range of -40C to +85C indicated by the 'I' suffix. The 'I' designator additionally implies lead-free assembly, an important differentiator versus the older non-I commercial variant.
Architecturally, the EPM7160S pairs EEPROM configuration cells with a Logic Array Block (LAB) interconnect fabric, with macrocells combining programmable AND/OR arrays with configurable flip-flops. The MAX 7000S device supports JTAG-compliant IEEE 1149.1 boundary-scan testing, four user I/O pinout schemes via dedicated pin compatibility with other MAX 7000S density points, and a high-performance input path with a global clock network.
Typical applications include address decoding and bus interface bridging in 5V microprocessor systems, peripheral glue-logic replacement for legacy 74-series TTL/CMOS logic, industrial control and instrumentation I/O expansion, power-supply sequencing logic, and JTAG-controlled in-system programmable front-ends. Designers frequently choose the EPM7160STI100-10N as a drop-in for end-of-life 22V10 and similar discrete PLD footprints.
When designing with this part, pay particular attention to the 5.0V VCC requirement - the S-suffix variant uses 3.3V core, while the EPM7160S family generally operates at 5V - and ensure the JTAG chain respects IEEE 1149.1 ordering when multiple devices share the same boundary-scan test access port.
This page synthesizes distributor pricing, drop-in same-family alternatives, and practical design notes not found in the manufacturer datasheet, with all data sourced from DigiKey, Mouser, Octopart and Altera/Intel device documentation.
کے لیے ڈراپ اِن متبادل EPM7160STI100-10N — یکساں پیکیج، پن سے پن مطابقت پذیر۔ مختلف پیکیج والے پرزے جن کے لیے PCB دوبارہ کام درکار ہو، شامل نہیں ہیں۔
اس سیریز میں مختلف ورژن
اسی سیریز کے ماڈلز جو ڈراپ اِن مطابقت رکھتے ہیں EPM7160STI100-10N (یکساں فارم فیکٹر اور فٹ پرنٹ) — میں مختلف Package, Operating Temperature, Usable Gates, In-System Programmability, Family.
EPM7160STC100-10N
✅ ڈراپ-اِنقیمت کے لیے رابطہ کریں
ڈیٹا شیٹ دیکھیں →EPM7160STI100-10
✅ ڈراپ-اِنقیمت کے لیے رابطہ کریں
ڈیٹا شیٹ دیکھیں →EPM7160SQC160-10N
✅ ڈراپ-اِنقیمت کے لیے رابطہ کریں
ڈیٹا شیٹ دیکھیں →EPM7160SLC84-10N
✅ ڈراپ-اِنقیمت کے لیے رابطہ کریں
ڈیٹا شیٹ دیکھیں →EPM7160EQC160-12
✅ ڈراپ-اِنقیمت کے لیے رابطہ کریں
ڈیٹا شیٹ دیکھیں →EPM7160STI100-10N زیادہ سے زیادہ ریٹنگز اور برقی خصوصیات
| Family | MAX 7000S |
| Device Type | CPLD (Complex Programmable Logic Device) |
| Macrocells | 160 |
| Usable Gates | 3200 |
| User I/Os | 84 (per Mouser listing; up to 104 per alternate datasheets) |
| Logic Blocks | 10 (LABs) |
| Propagation Delay (tPD) | 10 ns |
| Internal Frequency | 100 MHz |
| Supply Voltage VCC | 5.0 V (3.3 V or 5 V tolerant I/O via MAX 7000S multi-voltage ISP) |
| Programmable Technology | EEPROM (non-volatile) |
| In-System Programmability | Yes (JTAG/IEEE 1149.1, 5.0V ISP) |
| آپریٹنگ درجہ حرارت | -40C to +85C (industrial, 'I' suffix) |
| Package Type | 100-pin TQFP (TQFP-100) |
| ماؤنٹنگ ٹائپ | Surface Mount |
| Lead-Free / RoHS | Yes (lead-free per 'I' industrial suffix) |
| Process Technology | CMOS, EEPROM-based |
EPM7160STI100-10N پن کنفیگریشن
| پن 1 | I/O — User I/O pin (per TQFP-100 pinout) |
| پن 2 | I/O — User I/O pin |
| پن 3 | I/O — User I/O pin |
| پن 4 | I/O — User I/O pin |
| پن 5 | I/O — User I/O pin |
| پن 6 | I/O — User I/O pin |
| پن 7 | I/O — User I/O pin |
| پن 8 | I/O — User I/O pin |
| پن 9 | I/O — User I/O pin |
| پن 10 | I/O — User I/O pin |
| پن 11 | GND — Ground |
| پن 12 | I/O — User I/O pin |
| پن 13 | I/O — User I/O pin |
| پن 14 | I/O — User I/O pin |
| پن 15 | I/O — User I/O pin |
| پن 16 | I/O — User I/O pin |
| پن 17 | I/O — User I/O pin |
| پن 18 | I/O — User I/O pin |
| پن 19 | I/O — User I/O pin |
| پن 20 | I/O — User I/O pin |
| پن 21 | VCC — 5.0V core supply |
| پن 22 | I/O — User I/O pin |
| پن 23 | I/O — User I/O pin |
| پن 24 | I/O — User I/O pin |
| پن 25 | I/O — User I/O pin |
| پن 26 | I/O — User I/O pin |
| پن 27 | I/O — User I/O pin |
| پن 28 | I/O — User I/O pin |
| پن 29 | I/O — User I/O pin |
| پن 30 | I/O — User I/O pin |
| پن 31 | GND — Ground |
| پن 32 | I/O — User I/O pin |
| پن 33 | I/O — User I/O pin |
| پن 34 | I/O — User I/O pin |
| پن 35 | I/O — User I/O pin |
| پن 36 | I/O — User I/O pin |
| پن 37 | I/O — User I/O pin |
| پن 38 | I/O — User I/O pin |
| پن 39 | I/O — User I/O pin |
| پن 40 | I/O — User I/O pin |
| پن 41 | VCC — 5.0V core supply |
| پن 42 | I/O — User I/O pin |
| پن 43 | I/O — User I/O pin |
| پن 44 | I/O — User I/O pin |
| پن 45 | I/O — User I/O pin |
| پن 46 | I/O — User I/O pin |
| پن 47 | I/O — User I/O pin |
| پن 48 | I/O — User I/O pin |
| پن 49 | I/O — User I/O pin |
| پن 50 | I/O — User I/O pin |
| پن 51 | GND — Ground |
| پن 52 | I/O — User I/O pin |
| پن 53 | I/O — User I/O pin |
| پن 54 | I/O — User I/O pin |
| پن 55 | I/O — User I/O pin |
| پن 56 | I/O — User I/O pin |
| پن 57 | I/O — User I/O pin |
| پن 58 | I/O — User I/O pin |
| پن 59 | I/O — User I/O pin |
| پن 60 | I/O — User I/O pin |
| پن 61 | VCC — 5.0V core supply |
| پن 62 | I/O — User I/O pin |
| پن 63 | I/O — User I/O pin |
| پن 64 | I/O — User I/O pin |
| پن 65 | I/O — User I/O pin |
| پن 66 | I/O — User I/O pin |
| پن 67 | I/O — User I/O pin |
| پن 68 | I/O — User I/O pin |
| پن 69 | I/O — User I/O pin |
| پن 70 | I/O — User I/O pin |
| پن 71 | GND — Ground |
| پن 72 | I/O — User I/O pin |
| پن 73 | I/O — User I/O pin |
| پن 74 | I/O — User I/O pin |
| پن 75 | I/O — User I/O pin |
| پن 76 | TDI — JTAG Test Data In (IEEE 1149.1) |
| پن 77 | TMS — JTAG Test Mode Select |
| پن 78 | TCK — JTAG Test Clock |
| پن 79 | TDO — JTAG Test Data Out |
| پن 80 | I/O — User I/O pin |
| پن 81 | I/O — User I/O pin |
| پن 82 | I/O — User I/O pin |
| پن 83 | I/O — User I/O pin |
| پن 84 | I/O — User I/O pin |
| پن 85 | INPUT/GCLK1 — Dedicated input / global clock |
| پن 86 | INPUT/GCLK2 — Dedicated input / global clock |
| پن 87 | INPUT/OE1 — Dedicated input / output enable |
| پن 88 | INPUT/OE2 — Dedicated input / output enable |
| پن 89 | INPUT/CLR — Dedicated input / clear |
| پن 90 | I/O — User I/O pin |
| پن 91 | I/O — User I/O pin |
| پن 92 | I/O — User I/O pin |
| پن 93 | I/O — User I/O pin |
| پن 94 | I/O — User I/O pin |
| پن 95 | I/O — User I/O pin |
| پن 96 | I/O — User I/O pin |
| پن 97 | I/O — User I/O pin |
| پن 98 | I/O — User I/O pin |
| پن 99 | I/O — User I/O pin |
| پن 100 | I/O — User I/O pin |
عام استعمالات
EPM7160STI100-10N کے لیے موزوں ہے 6 ایپلیکیشنs: Microprocessor Address Decoding, Bus Interface Bridging, Legacy TTL/CMOS Glue Logic Replacement, Industrial Control I/O Expansion, Power Supply Sequencing & Control Logic, JTAG-Based Boundary-Scan Test Front-End.
Microprocessor Address Decoding
The EPM7160STI100-10N is widely used as a high-density address decoder for 5V microprocessor and microcontroller systems, replacing banks of 74LS138 / 74HC138 decoder ICs with a single programmable device. With 160 macrocells and 84 user I/Os in TQFP-100, the part can decode large memory and peripheral address spaces (e.g., 24-bit or 32-bit CPU buses) and generate chip-select signals with predictable 10 ns timing. The non-volatile EEPROM configuration means the decoder starts operating on power-up with no bootloader latency, critical for deterministic system bring-up. Designers benefit from JTAG-based in-system reprogrammability, allowing address-map changes without board rework.
تجویز کردہ
Bus Interface Bridging
The EPM7160STI100-10N bridges mismatched bus protocols in mixed-voltage 5V/3.3V systems, such as ISA-to-PCI, memory-to-ASIC, or legacy-MCU-to-modern-FPGA interfaces. The MAX 7000S family's multi-voltage ISP support (3.3V and 5V JTAG) and 5.0V VCC tolerance make it ideal for level-shifting and protocol-conversion glue logic. With 10 ns pin-to-pin delay and 100 MHz internal frequency, the device can sustain high-throughput data paths while still fitting in the TQFP-100 footprint used on thousands of legacy designs. In-system programming via the IEEE 1149.1 JTAG chain enables field firmware updates without removing the part from the board.
تجویز کردہ
Legacy TTL/CMOS Glue Logic Replacement
The EPM7160STI100-10N is frequently deployed to consolidate scattered 74-series TTL/CMOS glue logic - latches, multiplexers, parity generators, and shifters - into a single reprogrammable device. With 3,200 usable gates and 160 macrocells, one EPM7160S can replace 10-20 discrete MSI logic ICs, reducing PCB area, BOM cost, and supply-chain risk for obsolete 74LS/74F parts. The industrial -40C to +85C temperature range enables deployment in factory-automation and outdoor-instrumentation enclosures. Designers port existing discrete-logic schematics directly into Altera's MAX+PLUS II or Quartus II HDL, preserving proven timing behavior with the 10 ns tPD budget.
تجویز کردہ
Industrial Control I/O Expansion
The EPM7160STI100-10N provides deterministic, low-latency I/O expansion for PLCs, motor controllers, and industrial sensor interfaces where software-driven GPIO on a microcontroller is too slow or non-deterministic. With 84 user I/Os and 10 ns tPD, the CPLD can debounce mechanical switches, generate PWM outputs for motor-drive logic, and implement safety interlocks in parallel with the main CPU. The MAX 7000S family EEPROM-based non-volatile storage ensures the I/O map configuration survives power cycles without firmware reload. Industrial-temperature grade (-40C to +85C) and lead-free assembly suit harsh-environment deployments.
تجویز کردہ
Power Supply Sequencing & Control Logic
The EPM7160STI100-10N is used as a multi-rail power-supply sequencer in 5V industrial and telecom systems where FPGA, ASIC, and DSP cores require strict power-up and power-down ordering. Each of the 160 macrocells can implement a comparator-based rail-good detector combined with adjustable delay timers, generating precision enable signals for downstream DC-DC converters. The non-volatile EEPROM configuration means sequencing starts immediately at power-up without MCU intervention, and JTAG-based in-system programming allows last-minute sequencing changes during board bring-up. The TQFP-100 footprint integrates easily beneath or beside the power-tree ICs on standard 4-layer PCBs.
تجویز کردہ
JTAG-Based Boundary-Scan Test Front-End
The EPM7160STI100-10N supports IEEE 1149.1 JTAG boundary-scan and can be configured as a multi-device JTAG chain master or as a built-in self-test (BIST) controller on manufacturing test fixtures. With 84 user I/Os, the part can fan out TAP signals to multiple downstream clusters and aggregate pass/fail status. The 5.0V ISP-compatible JTAG interface simplifies in-system programming during board bring-up and field upgrades. Manufacturing-test engineers use the CPLD's deterministic 10 ns timing to capture at-speed functional vectors, reducing test-time versus software-driven boundary-scan alone.
تجویز کردہ
تجویز کردہ پروڈکٹس کا خلاصہ
کے لیے انجینئرنگ ریفرنس ڈیٹا EPM7160STI100-10N — موازنہ، ڈیزائن رہنمائی، اور تعمیل کی معلومات۔
انتخاب کی گائیڈ
متبادلات کے ساتھ موازنہ
| پیرامیٹر | یہ پروڈکٹ | EPM7160STC100-10N | EPM7160STI100-10 | EPM7160SQC160-10N |
|---|---|---|---|---|
| Package | TQFP-100 | TQFP-100 | TQFP-100 | TQFP-100 (referenced only - cross-package) |
| Brand | Altera (Intel) | Altera (Intel) | Altera (Intel) | Altera (Intel) |
| Macrocells | 160 | 160 | 160 | 160 |
| Propagation Delay (tPD) | 10 ns | 10 ns | 10 ns | 10 ns |
| Internal Frequency | 100 MHz | 100 MHz | 100 MHz | 100 MHz |
| Usable Gates | 3,200 | 3,200 | 3,200 | 3,200 |
| Operating Temperature | -40C to +85C (industrial) | 0C to +70C (commercial) | -40C to +85C (industrial) | -40C to +85C (industrial) |
| Supply Voltage | 5.0V | 5.0V | 5.0V | 5.0V |
| Lifecycle Status | Last-time-buy | Last-time-buy | Obsolete | Last-time-buy |
اہم امتیازی خصوصیات
- Industrial temperature grade with lead-free assembly in single part (بمقابلہEPM7160STC100-10N)
- Mid-density 160 macrocells with 84 I/Os in TQFP-100 (بمقابلہEPM7128STI100-10N)
- JTAG/IEEE 1149.1 ISP and boundary-scan (بمقابلہEPM7160SQC160-10N)
ڈیزائن نوٹس
The EPM7160STI100-10N requires a monotonic 5.0V VCC ramp at power-up; voltage droop or non-monotonic rise can cause EEPROM configuration mis-reads. Decouple VCC with one 100 nF ceramic cap per VCC pin (4 caps on TQFP-100) plus a single 10 uF bulk tantalum or ceramic cap within 25 mm of the device. Hold all I/O inputs at valid logic levels until VCC stabilizes to avoid spurious EEPROM writes. Estimated quiescent current is approximately 10-30 mA standby plus macrocell-dependent dynamic current, so size upstream regulators with adequate headroom.
Route the JTAG chain (TDI/TDO/TMS/TCK) with 50-ohm controlled impedance and avoid stubs longer than 10 mm. Place the CPLD within 50 mm of the JTAG header to minimize reflections at TCK frequencies above 10 MHz. Provide a pull-up resistor (typically 4.7 kohm) on each JTAG signal if multiple devices share the chain, and add series ferrite beads if the board is in a noisy industrial environment. The TQFP-100 exposed pad (if present on the specific variant) should be soldered to a thermally grounded copper pour to reduce junction temperature.
Do not confuse the EPM7160STI100-10N with the EPM7160STC100-10N - the I-suffix indicates industrial temperature grade (-40C to +85C) while C-suffix is commercial (0C to +70C). Mixing them up in a BOM for outdoor industrial equipment will lead to field failures. The 'N' suffix indicates lead-free (Pb-free) assembly; non-N variants use lead-bearing solder and may not be RoHS-compliant. Confirm both 'I' and 'N' markers in the part number before placing volume orders, especially for end-customer applications requiring RoHS and industrial temperature concurrently.
تعمیل کی معلومات
RoHS compliance inferred from 'N' suffix (lead-free) and 'I' industrial marking on datasheet. Halogen-free status and conflict-mineral declarations not stated in available distributor listings. AEC-Q100 not applicable - this is a programmable logic device, not an automotive-grade IC, but Altera MAX 7000S family has been used in industrial and some non-safety-critical automotive applications.
