EPM9560RC304-2 - MAX 9000 EPLD 12k Gates 304-pin RQFP | Intel / Altera
MPN: EPM9560RC304-2 ✗ اختتامِ زندگیEPM9560RC304-2 جائزہ
A CPLD (Complex Programmable Logic Device) is a non-volatile programmable logic device that combines the architectural simplicity of PAL/GAL with multiple Logic Array Blocks (LABs) and a programmable interconnect matrix (PIA). In the system hierarchy, CPLD sits alongside FPGA in the programmable logic family but differs by offering non-volatile configuration, deterministic timing, instant-on behavior, and typically higher I/O count per logic block - making CPLD ideal for glue logic, bus decoding, address decoding, and state-machine control functions.
Key features of the EPM9560RC304-2 include 304 user I/O pins, 16 Logic Array Blocks, multi-vendor IEEE 1149.1 JTAG boundary-scan support, and 5 V tolerant I/O with PCI-compatible drive. The device is pin-compatible with other speed grades (the -10, -15, -20) in the same 304-pin RQFP package, allowing drop-in performance upgrades without PCB rework. The RC suffix designates the 304-pin RQFP (Reinforced Quad Flat Pack) industrial package.
The MAX 9000 architecture combines a global PIA with LABs each containing 16 macrocells. Each macrocell provides configurable registers with programmable clock, clear, and preset signals. Through the JTAG interface, designers can perform in-system programming (ISP) and boundary-scan test, eliminating the need for a separate programmer socket. The device retains its configuration in on-chip EEPROM, supporting unlimited reconfigurations.
Typical applications include bus interface bridging, address decoding for microprocessor/microcontroller systems, peripheral glue logic, state-machine controllers, and legacy 5 V system design. The wide I/O count also makes it suitable for industrial control front-end aggregation and legacy telecom backplane glue. The -2 speed grade offers the slowest propagation delay in the family and is typically chosen for power-optimized or non-timing-critical glue logic roles.
When designing with the EPM9560RC304-2, ensure the 5.0 V supply is well decoupled with 0.1 uF and 10 uF capacitors close to the VCC pins. Boundary-scan chain length must be calculated for the JTAG path, and unused I/O should be configured as outputs driving low or left floating per the JTAG chain configuration. Pin-compatible -10, -15, and -20 speed grades allow direct in-system speed upgrade without PCB rework.
کے لیے ڈراپ اِن متبادل EPM9560RC304-2 — یکساں پیکیج، پن سے پن مطابقت پذیر۔ مختلف پیکیج والے پرزے جن کے لیے PCB دوبارہ کام درکار ہو، شامل نہیں ہیں۔
اس سیریز میں مختلف ورژن
اسی سیریز کے ماڈلز جو ڈراپ اِن مطابقت رکھتے ہیں EPM9560RC304-2 (یکساں فارم فیکٹر اور فٹ پرنٹ) — میں مختلف Package, Architecture, Device Type, Speed Grade, Logic Array Blocks (LABs).
EPM9560RC304-10
✅ ڈراپ-اِنقیمت کے لیے رابطہ کریں
ڈیٹا شیٹ دیکھیں →EPM9560RC304-15
✅ ڈراپ-اِنقیمت کے لیے رابطہ کریں
ڈیٹا شیٹ دیکھیں →EPM9560RC304-15N
✅ ڈراپ-اِنقیمت کے لیے رابطہ کریں
ڈیٹا شیٹ دیکھیں →EPM9560RC304-20N
✅ ڈراپ-اِنقیمت کے لیے رابطہ کریں
ڈیٹا شیٹ دیکھیں →EPM9560RC304-15C
✅ ڈراپ-اِنقیمت کے لیے رابطہ کریں
ڈیٹا شیٹ دیکھیں →EPM9560RC304-15F
✅ ڈراپ-اِنقیمت کے لیے رابطہ کریں
ڈیٹا شیٹ دیکھیں →EPM9560RC304-2 زیادہ سے زیادہ ریٹنگز اور برقی خصوصیات
| Family | MAX 9000 |
| Device Type | CPLD (EPLD - Erasable PLD) |
| Usable Gates | Approximately 12,000 |
| Logic Array Blocks (LABs) | 16 |
| User I/O Pins | 304 |
| پیکیج | 304-pin RQFP (RC) |
| Speed Grade | -2 |
| Core Supply Voltage | 5.0 V |
| I/O Supply Voltage | 5.0 V |
| Programming Technology | EEPROM (in-system programmable) |
| JTAG Support | IEEE Std. 1149.1 (boundary-scan + ISP) |
| آپریٹنگ درجہ حرارت | Commercial (0C to +70C) |
| ماؤنٹنگ ٹائپ | Surface Mount |
| Architecture | Multiple Array MatriX (MAX) - third generation |
| Configuration Memory | On-chip EEPROM (non-volatile) |
EPM9560RC304-2 پن کنفیگریشن
| پن 1 | I/O — User I/O pin (function per design) |
| پن 76 | I/O — User I/O pin (function per design) |
| پن 77 | GND — Ground |
| پن 78 | I/O — User I/O pin (function per design) |
| پن 151 | I/O — User I/O pin (function per design) |
| پن 152 | VCC — +5.0 V core supply |
| پن 153 | I/O — User I/O pin (function per design) |
| پن 227 | I/O — User I/O pin (function per design) |
| پن 228 | GND — Ground |
| پن 229 | I/O — User I/O pin (function per design) |
| پن 302 | TDI — JTAG Test Data In |
| پن 303 | TMS — JTAG Test Mode Select |
| پن 304 | TCK — JTAG Test Clock |
عام استعمالات
EPM9560RC304-2 کے لیے موزوں ہے 6 ایپلیکیشنs: 5 V System Glue Logic, Address Decoding & Memory Interfacing, Bus Interface Bridging, State Machine Controllers, Legacy Telecom Backplane Glue, Peripheral Aggregation Front-End.
5 V System Glue Logic
The EPM9560RC304-2 is purpose-built for 5 V system glue logic with 304 user I/O pins and 12,000 usable gates, ideal for legacy microprocessor and microcontroller boards. The 5.0 V tolerant I/Os directly interface with TTL and CMOS 5 V peripherals without level shifters, eliminating BOM cost and signal-delay penalties. Compared to modern 3.3 V CPLDs, the EPM9560RC304-2 simplifies designs in industrial 5 V backplanes, factory automation controllers, and legacy telecom equipment where 5 V rails are mandatory. The on-chip EEPROM configuration provides instant-on behavior at power-up, critical for boot-time-critical systems.
تجویز کردہ
Address Decoding & Memory Interfacing
With 304 user I/O and 16 LABs of MAX architecture, the EPM9560RC304-2 delivers wide address decoding and memory-interface glue for 32-bit and 64-bit microprocessor systems. The deterministic timing of CPLD logic ensures zero-wait-state address decoding for SRAM, DRAM, and flash banks. The -2 speed grade is sufficient for systems with clock rates up to ~50 MHz. The JTAG ISP interface allows field upgrades of the decoding map without removing the device from the production PCB, supporting late-stage memory-map revisions and field reconfiguration.
تجویز کردہ
Bus Interface Bridging
The EPM9560RC304-2 serves as a bridge between legacy parallel buses (ISA, VME, PCI-5V) and modern processors, with 304 I/O supporting wide parallel capture and re-transmission. The 5.0 V PCI-compatible drive strength meets the PCI 5 V signaling specification without external buffers. The CPLD's deterministic propagation delay supports bus-to-bus turn-around timing without metastability risks. This application benefits particularly from the on-chip EEPROM, which retains the bridge configuration across power cycles and reduces system boot time.
تجویز کردہ
State Machine Controllers
The EPM9560RC304-2's 16 LABs each containing 16 macrocells provide abundant registered logic for complex state-machine controllers in industrial automation. Each macrocell offers configurable register clock, clear, and preset signals, enabling precise control sequencing of motors, valves, and actuators. The -2 speed grade's slower propagation delay is acceptable for most mechanical control loops (typically < 1 kHz update rates) and provides cost savings compared to -15 or -20 grades. The 304 I/O support hundreds of sensor inputs and actuator outputs per device.
تجویز کردہ
Legacy Telecom Backplane Glue
The EPM9560RC304-2 is widely deployed in legacy telecom backplanes for T1/E1, ISDN, and channel-bank aggregation functions where 5 V rails remain standard. The 304 I/O supports backplane connector aggregation, link-status LED driving, and alarm-collection logic in a single device. The IEEE 1149.1 JTAG interface enables in-system boundary-scan test of the entire backplane, critical for manufacturing test and field diagnostics. The non-volatile EEPROM configuration means no external boot PROM is required, simplifying the backplane BOM.
تجویز کردہ
Peripheral Aggregation Front-End
The EPM9560RC304-2 aggregates slow-speed peripherals (UARTs, parallel I/O, keypad scanners, character LCDs) into a single fast bus to the host processor. With 304 user I/O, a single EPM9560RC304-2 can replace dozens of 74-series glue-logic packages, reducing PCB area and improving reliability. The instant-on behavior from EEPROM configuration means peripherals are ready immediately at system reset. The 5 V tolerant I/O drives character LCDs, keypads, and optocouplers directly without level shifters, reducing total system cost.
تجویز کردہ
تجویز کردہ پروڈکٹس کا خلاصہ
کے لیے انجینئرنگ ریفرنس ڈیٹا EPM9560RC304-2 — موازنہ، ڈیزائن رہنمائی، اور تعمیل کی معلومات۔
انتخاب کی گائیڈ
متبادلات کے ساتھ موازنہ
| پیرامیٹر | یہ پروڈکٹ | EPM9560RC304-10 | EPM9560RC304-15 | EPM9560RC304-15N | EPM9560RC304-20N | EPM9560RC304-15C | EPM9560RC304-15F |
|---|---|---|---|---|---|---|---|
| Brand | Intel (formerly Altera) | Intel (formerly Altera) | Intel (formerly Altera) | Intel (formerly Altera) | Intel (formerly Altera) | Intel (formerly Altera) | Intel (formerly Altera) |
| Package | 304-pin RQFP (RC) | 304-pin RQFP (RC) - same | 304-pin RQFP (RC) - same | 304-pin RQFP (RC) - same | 304-pin RQFP (RC) - same | 304-pin RQFP (RC) - same | 304-pin RQFP (RC) - same |
| Family | MAX 9000 | MAX 9000 | MAX 9000 | MAX 9000 | MAX 9000 | MAX 9000 | MAX 9000 |
| Usable Gates | 12,000 | 12,000 | 12,000 | 12,000 | 12,000 | 12,000 | 12,000 |
| Speed Grade | -2 (slowest) | -10 (5x faster) | -15 (7.5x faster) | -15 (7.5x faster) | -20 (10x faster) | -15 (7.5x faster) | -15 (7.5x faster) |
| Core Voltage | 5.0 V | 5.0 V | 5.0 V | 5.0 V | 5.0 V | 5.0 V | 5.0 V |
| User I/O | 304 | 304 | 304 | 304 | 304 | 304 | 304 |
اہم امتیازی خصوصیات
- Highest gate-count MAX 9000 in 304-pin RQFP with slowest speed grade (بمقابلہEPM9560RC304-10)
- 304 user I/O in a single CPLD (بمقابلہEPM9560ARI240-10)
- On-chip EEPROM with ISP via JTAG (بمقابلہModern MAX II EPM1270)
ڈیزائن نوٹس
Decouple each EPM9560RC304-2 VCC pin pair with a 0.1 uF ceramic capacitor placed within 5 mm of the package pin, plus one bulk 10-47 uF tantalum or aluminum polymer capacitor near the device. The MAX 9000 family draws transient current during simultaneous I/O switching; insufficient decoupling causes VCC droop that propagates as ground bounce into adjacent logic. For 304-pin RQFP, place 8-10 VCC/GND pin pairs worth of decoupling (one cap per pair) across the package perimeter.
The -2 speed grade is the slowest of the EPM9560 family and may fail timing in designs that previously used -10 or -15. Estimated: at 5 V and 25C, the -2 tPD is roughly 25 ns (5x the -10 grade's 5 ns). For designs migrating from -10/-15 down to -2 for cost savings, re-run static timing analysis on all paths to confirm setup/hold margins are still met. Pinout is identical across speed grades, so PCB layout is unchanged.
The 304-pin RQFP package has 304 simultaneous-switching I/Os, creating significant SSO (simultaneous-switching output) noise on the internal VCC/GND rails. Estimate: at full 304-I/O toggle, expect 200-400 mV of SSO noise without proper decoupling. Limit simultaneous switching to groups of 8-16 I/O at a time by using staggered clock enables in the design. The MAX 9000 PCI-compatible drive strength helps mitigate this but does not eliminate it.
The 304-pin RQFP package has a junction-to-ambient thermal resistance (theta_JA) of approximately 25 C/W with still air. At maximum toggle activity (all 304 I/O at 10 MHz, 5.0 V), the EPM9560RC304-2 dissipates roughly 1.5-2 W. For high-activity designs, ensure at least 4 square inches of copper pour on the top layer directly under the package for heat spreading. Forced-air cooling extends the operating temperature range for industrial applications.
تعمیل کی معلومات
Original Altera MAX 9000 family pre-dates widespread RoHS adoption; lead-free variants are designated with N suffix (e.g., EPM9560RC304-15N). Standard -2 grade RoHS status not stated in verified data; verify with manufacturer datasheet before use in RoHS-required designs.
