ISL8563ECB - 3V RS232/RS562 Transceiver | Renesas | 18-SOIC
MPN: ISL8563ECB ✓ فعالISL8563ECB جائزہ
A transceiver is an interface integrated circuit that converts logic-level signals between a host controller and a physical communications link. The ISL8563E belongs to the RS232 transceiver category, where a transmitter translates CMOS/TTL levels into RS232-compatible levels and a receiver performs the inverse conversion. Supporting both EIA/TIA-232 and EIA/TIA-562 operation lets the same device serve conventional RS232 links and lower-voltage, higher-noise-tolerant RS562 applications while remaining a 3 V-compatible interface IC.
The principal operating features are a 3.0 V minimum supply, a 5.5 V maximum supply, two transmit channels, two receive channels, and 5 Mbps data-rate capability. Its broad supply range permits use in both 3.3 V and 5 V equipment. The manufacturer states that the transmitter and receiver circuits meet EIA/TIA-562 and EIA/TIA-232 specifications even when VCC is 3.0 V, providing design flexibility where the downstream system does not use a 5 V logic rail.
The ISL8563ECB also provides ±15 kV ESD protection on exposed RS-562 pins using the IEC 61000-4-2 air-gap and human-body-model methods. This protection is important on cables that leave an enclosure because electrostatic discharge events can otherwise damage a transceiver input or output. The 18-SOIC package is 0.295 inches, or 7.50 mm, wide and remains suitable for conventional surface-mount PCB assembly.
Typical applications include multi-drop industrial serial links, data acquisition equipment, instrumentation, POS terminals, industrial controllers, and communications interfaces requiring both RS232 and RS562 compatibility. In these systems, the device provides the electrical interface between a low-voltage digital controller and an external serial cable. Designers should select cable protection, grounding, and connector details for the installation because the IC cannot substitute for an earth-ground connection or complete surge-protection network.
A key design consideration is that the 18-SOIC footprint has 18 leads and requires a sufficiently wide land pattern; the package should not be confused with a narrow 8-pin SOIC. Review the manufacturer pin-description table before assigning signal names, and observe the stated supply range, receiver enable or shutdown behavior, and output-slew requirements during PCB review. The exposed interface pins should be routed away from unprotected board edges when practical.
This page organizes the verified technical characteristics, sourcing information, documented standards, and practical replacement considerations for engineers evaluating the ISL8563ECB. It also highlights the distinctions that matter when comparing this Renesas device with a 3.3 V RS562 transceiver in an 18-lead wide-SOIC package.
کے لیے ڈراپ اِن متبادل ISL8563ECB — یکساں پیکیج، پن سے پن مطابقت پذیر۔ مختلف پیکیج والے پرزے جن کے لیے PCB دوبارہ کام درکار ہو، شامل نہیں ہیں۔
MAX563CWN+T
✅ ڈراپ-اِن📋 حوالہ جاتی متبادل (کیٹلاگ میں نہیں)
ISL8563ECB تفصیلات
| Product Type | Dual RS232 and RS562 transceiver |
| Transmitter Channels | 2 channels |
| Receiver Channels | 2 channels |
| Supply Voltage Range | 3.0 V to 5.5 V |
| Minimum Operating Supply | 3.0 V |
| Maximum Operating Supply | 5.5 V |
| Maximum Data Rate | 5 Mbps |
| Supported Standards | EIA/TIA-232 and EIA/TIA-562 |
| ESD Protection | ±15 kV on RS-562 transmitter outputs and receiver inputs |
| ESD Test Method | IEC 61000-4-2 air-gap and human-body-model methods |
| پیکیج | 18-SOIC, 0.295 inch (7.50 mm) width |
| ماؤنٹنگ ٹائپ | Surface mount |
| RoHS اسٹیٹس | Compliant |
ISL8563ECB 18-soic, 0.295 inch (7.50 mm) width پن کنفیگریشن گائیڈ
ISL8563ECB (18-soic, 0.295 inch (7.50 mm) width پیکیج) کے لیے پن کنفیگریشن۔ پن نمبرنگ، فنکشنز اور کنکشن ڈایاگرامز مینوفیکچرر کے ڈیٹا شیٹ میں بیان کیے گئے ہیں۔ درست فٹ پرنٹ اور سولڈرنگ رہنما ہدایات کے لیے اسی سے رجوع کریں۔
کے لیے تفصیلی پن آؤٹ ڈیٹا دستیاب نہیں ISL8563ECB.
رجوع کریں ڈیٹا شیٹ مکمل پن کنفیگریشن کے لیے۔
عام استعمالات
ISL8563ECB کے لیے موزوں ہے 6 ایپلیکیشنs: Industrial Serial Data Acquisition, Instrumentation and Test Equipment, POS and Retail Terminal Interfaces, Embedded Controller Communication, Network and Communications Equipment, Medical and Diagnostic Equipment.
Industrial Serial Data Acquisition
The ISL8563ECB is appropriate for industrial measurement equipment that must collect data over RS232 or RS562 links. Two transmit channels and two receive channels allow one interface IC to serve bidirectional or multi-channel communication, while the 3.0 V to 5.5 V supply range supports 3.3 V and 5 V control hardware. Operation from a 3.0 V supply helps meet the stated EIA/TIA-232 and EIA/TIA-562 requirements in low-voltage systems. The ±15 kV ESD protection on exposed RS-562 pins adds useful connector-side resilience, although industrial installations still need correctly engineered grounding and surge protection.
تجویز کردہ
Instrumentation and Test Equipment
The ISL8563ECB fits laboratory and production-test instruments that exchange commands and measurement data with external fixtures or computers. A 5 Mbps maximum data rate supports high-throughput serial communication, while the 18-pin wide-SOIC format remains compatible with conventional surface-mount assembly methods. The integrated transmitter and receiver channels reduce the number of separate interface components needed for bidirectional ports. Its 3.0 V minimum supply is especially useful where the instrument controller operates at 3.3 V and maintaining EIA/TIA-232 compatibility remains important.
تجویز کردہ
POS and Retail Terminal Interfaces
The ISL8563ECB can support serial links between retail terminals, receipt printers, scanners, and service equipment. Two receive channels are useful when a terminal must monitor more than one peripheral, while the transmitter channels support outbound command and status links. Its 3.0 V to 5.5 V operating range accommodates compact systems built around either 3.3 V or 5 V processors. The EIA/TIA-562 capability can provide greater tolerance for noisy point-to-point cabling than a purely logic-level interface, provided the cable and grounding arrangement are appropriate.
تجویز کردہ
Embedded Controller Communication
The ISL8563ECB gives an embedded controller a compact interface to RS232 or RS562 peripherals without requiring separate driver and receiver ICs. Its 3.0 V minimum operating voltage permits use with 3.3 V control logic, while operation up to 5.5 V supports legacy 5 V systems. The 18-pin wide-SOIC package provides adequate lead spacing for automated assembly and inspection. Designers should place supply decoupling close to the device, preserve the datasheet's enable and shutdown connections, and use a connector design that supports the required cable shield and signal-ground arrangement.
تجویز کردہ
Network and Communications Equipment
The ISL8563ECB is suitable for communication equipment that uses RS232 or RS562 for local management, configuration, or service ports. The 5 Mbps capability supports short, controlled links between equipment and maintenance systems, while the dual-channel organization can simplify multiport equipment. The device's ability to operate at a 3.0 V supply is useful in modern 3.3 V network hardware. Installation requirements remain important because long unshielded cables can introduce noise and reflections; use controlled-impedance routing where appropriate and avoid treating the ESD rating as a substitute for external surge suppression.
تجویز کردہ
Medical and Diagnostic Equipment
The ISL8563ECB can be used in diagnostic and monitoring equipment requiring a legacy serial connection to a host computer, analyzer, or service interface. Two transmitters and two receivers allow bidirectional and multi-channel links within one package, and the 3.0 V to 5.5 V supply range supports both low-voltage portable platforms and 5 V instruments. The documented ±15 kV ESD protection on connector-facing RS-562 pins improves robustness against routine electrostatic discharge. Medical-system qualification, isolation, and applicable regulatory requirements must be evaluated independently for the complete equipment.
تجویز کردہ
تجویز کردہ پروڈکٹس کا خلاصہ
کے لیے انجینئرنگ ریفرنس ڈیٹا ISL8563ECB — موازنہ، ڈیزائن رہنمائی، اور تعمیل کی معلومات۔
انتخاب کی گائیڈ
متبادلات کے ساتھ موازنہ
| پیرامیٹر | یہ پروڈکٹ | MAX563CWN+T |
|---|---|---|
| Package | 18-SOIC, 0.295 inch (7.50 mm) width | 18-pin WSOIC |
| Brand | Renesas Electronics | Maxim Integrated |
| Product Type | Dual RS232 and RS562 transceiver | Dual EIA/TIA-562 transceiver |
| Transmitter Channels | 2 channels | 2 channels |
| Receiver Channels | 2 channels | 2 channels |
| Supply Voltage Range | 3.0 V to 5.5 V | 3.3 V powered |
| Communication Standards | EIA/TIA-232 and EIA/TIA-562 | EIA/TIA-562 |
اہم امتیازی خصوصیات
- Broader supported communication standard set (بمقابلہMAX563CWN+T)
- Wider supply-voltage operating range (بمقابلہMAX563CWN+T)
- Documented ESD protection on connector-facing RS-562 pins (بمقابلہMAX563CWN+T)
ڈیزائن نوٹس
Create the PCB footprint from the manufacturer drawing for the 18-SOIC package rather than using a generic narrow-SOIC pattern. The documented body width is 0.295 inch, or 7.50 mm, so lead span and row spacing must match that drawing. Place the power-decoupling capacitor close to VCC and ground, and provide a low-impedance ground-plane path beneath the transceiver. Confirm exposed and enable-related pin assignments against the pin-description table before routing.
Do not assume every 18-lead RS562 transceiver is pin- and behavior-compatible. The ISL8563ECB supports a 3.0 V to 5.5 V supply and both EIA/TIA-232 and EIA/TIA-562, while the MAX563CWN+T is described as a 3.3 V EIA/TIA-562 device with active receivers during shutdown. Check supply limits, enable polarity, receiver outputs, transmitter pins, and shutdown states before approving a substitution. PCB artwork compatibility alone does not establish electrical equivalence.
Treat connector-facing RS-562 nets as potential high-voltage and high-transient nodes even though the IC specifies ±15 kV ESD protection. Keep those traces away from clocks, data buses, and analog inputs; provide a direct return path; and use chassis or board grounding consistent with the installation. If cables leave the enclosure or cross industrial environments, add appropriately rated surge and overvoltage protection rather than relying solely on the transceiver's internal ESD structures.
Operate the ISL8563ECB only within its specified 3.0 V to 5.5 V supply range. If the system rail can overshoot during power-off or hot-plug events, verify that the transient remains within the absolute maximum limits in the manufacturer datasheet. A 3.3 V supply is within range, but noise on the rail can affect communication margin; include local high-frequency bypass and keep the supply return path short.
تعمیل کی معلومات
The product listing identifies the ISL8563ECB as RoHS compliant. The manufacturer datasheet documents ±15 kV ESD protection tested under IEC 61000-4-2 air-gap and human-body-model methods; this is an ESD test method rather than product-level IEC certification. Other compliance attributes are unknown.