KSZ8794CNXIC - 4-Port Managed Ethernet Switch | Microchip
MPN: KSZ8794CNXIC ✓ فعالKSZ8794CNXIC جائزہ
An Ethernet switch is a semiconductor that connects multiple network endpoints through one uplink to a host, router, or wider network. The managed designation means the KSZ8794 provides Layer 2 switch functions rather than operating only as a basic repeater or hub. Within the networking hierarchy, it combines Ethernet switching, a 10/100BASE-T/TX PHY for copper ports, and a configurable Gigabit serial interface for the uplink.
The KSZ8794CNX is intended for cost-sensitive systems requiring three 10/100 Mbps copper ports and one Gigabit uplink. Its integrated design reduces the number of discrete network components required in industrial controllers, residential gateways, embedded equipment, and network appliances. Microchip identifies internal biasing, low power consumption, on-chip termination, and a small package outline as major cost and design benefits.
The uplink can operate with RGMII, MII, or RMII, allowing system architects to match the switch to processors, FPGAs, and other Ethernet-capable controllers according to timing, pin-count, and design-complexity requirements. This flexibility is particularly useful when one platform must support several host interfaces or when a product family needs to reuse related switch designs.
Typical implementation places the KSZ8794CNX between three copper-connected devices and a higher-speed network uplink. In an industrial controller, the copper ports can connect local sensors, service interfaces, or production equipment while the uplink carries aggregated traffic. In a residential gateway, the same arrangement supports three local Ethernet endpoints and a Gigabit connection to an access network or router.
Hardware implementation should follow the KSZ8794CNX Hardware Design Checklist, including guidance on magnetics, termination, layout, and interface implementation. The device also has an associated silicon errata and data-sheet clarification document, so production designs should account for the applicable silicon revision and current manufacturer documentation.
This page consolidates the verified switch architecture, interface options, package information, hardware-design guidance, errata context, and sourcing details into an engineering-focused overview. It also identifies which detailed electrical, timing, environmental, and pin-level values require confirmation from the current manufacturer datasheet before schematic release or PCB signoff.
کے لیے ڈراپ اِن متبادل KSZ8794CNXIC — یکساں پیکیج، پن سے پن مطابقت پذیر۔ مختلف پیکیج والے پرزے جن کے لیے PCB دوبارہ کام درکار ہو، شامل نہیں ہیں۔
اس سیریز میں مختلف ورژن
اسی سیریز کے ماڈلز جو ڈراپ اِن مطابقت رکھتے ہیں KSZ8794CNXIC (یکساں فارم فیکٹر اور فٹ پرنٹ).
اس پروڈکٹ کے لیے کوئی ڈراپ اِن متبادل دستیاب نہیں۔
متبادل کی درخواست کریںKSZ8794CNXIC زیادہ سے زیادہ ریٹنگز اور برقی خصوصیات
| Device Type | Layer 2 managed Ethernet switch |
| Copper Port Count | 3 ports |
| Copper Port Speed | 10/100 Mbps |
| Uplink Port Count | 1 port |
| Uplink Port Speed | 10/100/1000 Mbps |
| Uplink Interface Options | RGMII, MII, RMII |
| Ethernet Standards | 10/100BASE-T/TX |
| Network Layer | Layer 2 |
| پیکیج | 64-QFN, 8 mm x 8 mm |
| ماؤنٹنگ ٹائپ | Surface mount |
| Termination | On-chip termination |
| Biasing | Internal biasing |
| Design Focus | Low power consumption |
| Target Market | Cost-sensitive applications |
| RoHS اسٹیٹس | Compliant |
| REACH Status | unknown |
| Moisture Sensitivity Level | unknown |
| Automotive Qualification | not_applicable |
KSZ8794CNXIC 64-qfn, 8 mm x 8 mm پن کنفیگریشن گائیڈ
KSZ8794CNXIC (64-qfn, 8 mm x 8 mm پیکیج) کے لیے پن کنفیگریشن۔ پن نمبرنگ، فنکشنز اور کنکشن ڈایاگرامز مینوفیکچرر کے ڈیٹا شیٹ میں بیان کیے گئے ہیں۔ درست فٹ پرنٹ اور سولڈرنگ رہنما ہدایات کے لیے اسی سے رجوع کریں۔
کے لیے تفصیلی پن آؤٹ ڈیٹا دستیاب نہیں KSZ8794CNXIC.
رجوع کریں ڈیٹا شیٹ مکمل پن کنفیگریشن کے لیے۔
عام استعمالات
KSZ8794CNXIC کے لیے موزوں ہے 6 ایپلیکیشنs: Industrial Control Gateway, Residential Network Gateway, Embedded Equipment Ethernet Interface, Network Appliance with Local Ports, Process and Factory Automation Hub, Secure Edge and IoT Gateway.
Industrial Control Gateway
The KSZ8794CNXIC fits an industrial controller that must consolidate three local 10/100 Mbps Ethernet endpoints before connecting to a higher-speed network. Its three copper ports can serve sensors, service equipment, or machine-side controllers, while the fourth port provides a 10/100/1000 Mbps uplink. The configurable RGMII, MII, or RMII interface lets the design align with the controller processor or FPGA. Microchip identifies the device for cost-sensitive systems and provides a dedicated hardware design checklist. Final deployment still requires confirmation of electrical limits, isolation requirements, magnetics, operating temperature, and environmental qualifications for the specific machine.
Residential Network Gateway
A residential gateway can use the KSZ8794CNXIC to provide three 10/100 Mbps local Ethernet connections and one Gigabit uplink. This arrangement avoids requiring separate switching for every attached device while keeping the uplink capable of 1000 Mbps traffic. The managed Layer 2 architecture supports controlled network behavior, and the configurable host interface can accommodate different embedded processors or FPGA designs. According to Microchip, internal biasing, on-chip termination, low power consumption, and the small 64-QFN 8 mm by 8 mm package support compact, cost-sensitive gateway implementations. Board-level validation should follow the current hardware design checklist.
Embedded Equipment Ethernet Interface
The KSZ8794CNXIC is suitable for embedded equipment that needs to expose several wired Ethernet connections to a host processor. Ports 1 through 3 operate as 10/100 Mbps copper links, while Port 4 provides a configurable uplink that can use RGMII, MII, or RMII. This flexibility helps equipment designers balance host interface width, signal timing, and PCB complexity against the requirement for a Gigabit uplink. The integrated switch is especially relevant where three separate PHY or switch assemblies would increase board area and component count. Engineers should verify the exact PHY implementation, magnetics strategy, termination, reference clock, and management firmware requirements against the manufacturer documentation.
Network Appliance with Local Ports
A compact network appliance can use the KSZ8794CNXIC to provide local Ethernet service ports and a fast uplink to a router or core switch. Three 10/100 Mbps ports handle legacy or lower-bandwidth endpoints, while the 10/100/1000 Mbps uplink prevents the four-port assembly from constraining aggregation traffic. The managed Layer 2 feature set is useful when the host software needs control over port behavior and status. Microchip highlights the device's low power consumption and package size as benefits for compact systems. During schematic design, confirm host-interface mode, PHY magnetics, internal versus external termination requirements, thermal conditions, and the exact pin assignments for the 64-QFN footprint.
Process and Factory Automation Hub
The KSZ8794CNXIC can act as the Ethernet aggregation point in a process or factory automation hub. Local equipment uses the three 10/100 Mbps copper ports, and plant infrastructure or an edge controller receives traffic through the Gigabit uplink. A Layer 2 managed switch is appropriate when the supervising controller requires port-level configuration and status information. The KSZ8794CNXIC's RGMII, MII, and RMII choices support different host-controller arrangements, including processor- and FPGA-based systems. Because industrial deployments can impose stricter temperature, surge, isolation, and regulatory requirements, engineers should confirm those specifications in the manufacturer datasheet and apply the KSZ8794CNX hardware design checklist before layout release.
Secure Edge and IoT Gateway
The KSZ8794CNXIC is appropriate for an IoT or secure-edge gateway that must collect traffic from several local wired endpoints and forward it over a Gigabit uplink. The three 10/100 Mbps copper ports provide basic device connectivity, while the managed switch supports a Layer 2 architecture commonly used by embedded network software. Its configurable uplink can connect to an application processor through RMII for a reduced pin-count design, MII for conventional separated clocking, or RGMII for higher-bandwidth parallel signaling. According to Microchip, the device targets cost-sensitive applications and emphasizes low power use, internal biasing, and on-chip termination. Validate security-control firmware, thermal margins, and network timing before deployment.
کے لیے انجینئرنگ ریفرنس ڈیٹا KSZ8794CNXIC — موازنہ، ڈیزائن رہنمائی، اور تعمیل کی معلومات۔
انتخاب کی گائیڈ
Do not select it for a four-port all-Gigabit design, a design requiring more than three copper ports, or a host that cannot support RGMII, MII, or RMII. No verified drop-in replacement was identified in the available cross-reference results, so changing manufacturers should be treated as a redesign until the footprint, exposed pad, supply rails, PHY behavior, management registers, and host timing are proven equivalent. Use the KSZ8794CNX Hardware Design Checklist and current errata before release.
متبادلات کے ساتھ موازنہ
| پیرامیٹر | یہ پروڈکٹ |
|---|---|
| Brand | Microchip Technology |
| Package | 64-QFN, 8 mm x 8 mm |
| Managed Layer | Layer 2 |
| Copper Port Count | 3 ports |
| Copper Port Speed | 10/100 Mbps |
| Uplink Port Count | 1 port |
| Uplink Port Speed | 10/100/1000 Mbps |
| Host Interface Options | RGMII, MII, RMII |
| Termination | On-chip termination |
| Design Focus | Cost-sensitive, low-power applications |
اہم امتیازی خصوصیات
- Combines three copper ports with a configurable Gigabit-class uplink (بمقابلہGeneric unmanaged four-port copper switch)
- Supports three host interface configurations (بمقابلہFixed-interface Ethernet switch)
- Integration reduces auxiliary circuit requirements (بمقابلہDiscrete Ethernet switch and PHY implementation)
- Compact package supports compact equipment (بمقابلہLarger-package managed Ethernet switch)
ڈیزائن نوٹس
Base the PCB layout on the KSZ8794CNX Hardware Design Checklist and the current manufacturer datasheet. Treat the 64-QFN footprint, exposed pad, supply connections, reference clocks, and high-speed uplink routes as one constrained design area. Keep RGMII or MII timing paths short, control return-current paths, and follow the manufacturer's recommended component placement and decoupling arrangement before making independent impedance or spacing changes.
Do not finalize supply rails, decoupling, or power sequencing from the general feature description alone. Confirm the required core and interface voltages, current limits, tolerance, startup behavior, and exposed-pad connection in the manufacturer datasheet. The KSZ8794CNX's low-power focus and internal biasing can simplify a design, but external rail quality still determines Ethernet clock and signal reliability.
Check the applicable KSZ87xx silicon errata and data-sheet clarification before freezing the design. The silicon revision can be identified from the device's top marking, and some documented clarifications may affect register interpretation or implementation. Pair that review with the hardware design checklist so the schematic, firmware configuration, magnetics selection, and PCB layout all use the same revision-specific requirements.
Select RGMII, MII, or RMII according to host timing and routing constraints rather than treating the interfaces as electrically interchangeable. RGMII uses a wide high-speed signal group, while RMII favors a smaller host connection and MII follows a more conventional separated clock-and-data arrangement. Follow the manufacturer's clock, trace-length, grounding, and decoupling guidance for the selected mode and preserve signal integrity through the complete host-to-switch path.
تعمیل کی معلومات
RoHS compliance is identified by the product information. REACH, lead-free status, halogen-free status, and conflict-minerals status are not established for the exact ordering code.