Microchip Technology

KSZ8794CNXIC - 4-Port Managed Ethernet Switch | Microchip

MPN: KSZ8794CNXIC ✓ 啟用中
10/100BASE-T/TX Rds(on) 64-QFN, 8 mm x 8 mm Package 10/100 Mbps Speed
MOQ: 1 |

KSZ8794CNXIC 概覽

The Microchip Technology KSZ8794CNXIC is a highly integrated, Layer 2 managed Ethernet switch with three 10/100 Mbps copper ports and one 10/100/1000 Mbps uplink port, housed in a 64-QFN 8 mm by 8 mm package. Its configurable RGMII, MII, and RMII uplink interface supports flexible host connections while the four-port architecture combines copper-port switching with a Gigabit uplink.

An Ethernet switch is a semiconductor that connects multiple network endpoints through one uplink to a host, router, or wider network. The managed designation means the KSZ8794 provides Layer 2 switch functions rather than operating only as a basic repeater or hub. Within the networking hierarchy, it combines Ethernet switching, a 10/100BASE-T/TX PHY for copper ports, and a configurable Gigabit serial interface for the uplink.

The KSZ8794CNX is intended for cost-sensitive systems requiring three 10/100 Mbps copper ports and one Gigabit uplink. Its integrated design reduces the number of discrete network components required in industrial controllers, residential gateways, embedded equipment, and network appliances. Microchip identifies internal biasing, low power consumption, on-chip termination, and a small package outline as major cost and design benefits.

The uplink can operate with RGMII, MII, or RMII, allowing system architects to match the switch to processors, FPGAs, and other Ethernet-capable controllers according to timing, pin-count, and design-complexity requirements. This flexibility is particularly useful when one platform must support several host interfaces or when a product family needs to reuse related switch designs.

Typical implementation places the KSZ8794CNX between three copper-connected devices and a higher-speed network uplink. In an industrial controller, the copper ports can connect local sensors, service interfaces, or production equipment while the uplink carries aggregated traffic. In a residential gateway, the same arrangement supports three local Ethernet endpoints and a Gigabit connection to an access network or router.

Hardware implementation should follow the KSZ8794CNX Hardware Design Checklist, including guidance on magnetics, termination, layout, and interface implementation. The device also has an associated silicon errata and data-sheet clarification document, so production designs should account for the applicable silicon revision and current manufacturer documentation.

This page consolidates the verified switch architecture, interface options, package information, hardware-design guidance, errata context, and sourcing details into an engineering-focused overview. It also identifies which detailed electrical, timing, environmental, and pin-level values require confirmation from the current manufacturer datasheet before schematic release or PCB signoff.

直接替換替代品,適用於 KSZ8794CNXIC — 相同封裝,腳位對腳位相容。需重新設計 PCB 的不同封裝零件不列入。

此系列的變體

與下列產品可直接替換的同系列型號: KSZ8794CNXIC (相同外形與佔位).

此產品無可直接替換的替代品。

申請替代品

KSZ8794CNXIC 最大額定值與電氣特性

Device Type Layer 2 managed Ethernet switch
Copper Port Count 3 ports
Copper Port Speed 10/100 Mbps
Uplink Port Count 1 port
Uplink Port Speed 10/100/1000 Mbps
Uplink Interface Options RGMII, MII, RMII
Ethernet Standards 10/100BASE-T/TX
Network Layer Layer 2
封裝 64-QFN, 8 mm x 8 mm
安裝類型 Surface mount
Termination On-chip termination
Biasing Internal biasing
Design Focus Low power consumption
Target Market Cost-sensitive applications
RoHS 狀態 Compliant
REACH Status unknown
Moisture Sensitivity Level unknown
Automotive Qualification not_applicable

KSZ8794CNXIC 64-qfn, 8 mm x 8 mm 腳位配置指南

KSZ8794CNXIC(64-qfn, 8 mm x 8 mm 封裝)的腳位配置。 腳位編號、功能與連接圖定義於製造商資料手冊中。請參閱該手冊以取得確切的封裝尺寸與焊接指引。

KSZ8794CNXIC 的 64-qfn, 8 mm x 8 mm 封裝腳位圖

無詳細腳位定義資料: KSZ8794CNXIC.

請參閱 資料表 以查看完整腳位配置。

典型應用

KSZ8794CNXIC 適用於 6 應用s: Industrial Control Gateway, Residential Network Gateway, Embedded Equipment Ethernet Interface, Network Appliance with Local Ports, Process and Factory Automation Hub, Secure Edge and IoT Gateway.

🏭

Industrial Control Gateway

The KSZ8794CNXIC fits an industrial controller that must consolidate three local 10/100 Mbps Ethernet endpoints before connecting to a higher-speed network. Its three copper ports can serve sensors, service equipment, or machine-side controllers, while the fourth port provides a 10/100/1000 Mbps uplink. The configurable RGMII, MII, or RMII interface lets the design align with the controller processor or FPGA. Microchip identifies the device for cost-sensitive systems and provides a dedicated hardware design checklist. Final deployment still requires confirmation of electrical limits, isolation requirements, magnetics, operating temperature, and environmental qualifications for the specific machine.

🌐

Residential Network Gateway

A residential gateway can use the KSZ8794CNXIC to provide three 10/100 Mbps local Ethernet connections and one Gigabit uplink. This arrangement avoids requiring separate switching for every attached device while keeping the uplink capable of 1000 Mbps traffic. The managed Layer 2 architecture supports controlled network behavior, and the configurable host interface can accommodate different embedded processors or FPGA designs. According to Microchip, internal biasing, on-chip termination, low power consumption, and the small 64-QFN 8 mm by 8 mm package support compact, cost-sensitive gateway implementations. Board-level validation should follow the current hardware design checklist.

🔧

Embedded Equipment Ethernet Interface

The KSZ8794CNXIC is suitable for embedded equipment that needs to expose several wired Ethernet connections to a host processor. Ports 1 through 3 operate as 10/100 Mbps copper links, while Port 4 provides a configurable uplink that can use RGMII, MII, or RMII. This flexibility helps equipment designers balance host interface width, signal timing, and PCB complexity against the requirement for a Gigabit uplink. The integrated switch is especially relevant where three separate PHY or switch assemblies would increase board area and component count. Engineers should verify the exact PHY implementation, magnetics strategy, termination, reference clock, and management firmware requirements against the manufacturer documentation.

🖥️

Network Appliance with Local Ports

A compact network appliance can use the KSZ8794CNXIC to provide local Ethernet service ports and a fast uplink to a router or core switch. Three 10/100 Mbps ports handle legacy or lower-bandwidth endpoints, while the 10/100/1000 Mbps uplink prevents the four-port assembly from constraining aggregation traffic. The managed Layer 2 feature set is useful when the host software needs control over port behavior and status. Microchip highlights the device's low power consumption and package size as benefits for compact systems. During schematic design, confirm host-interface mode, PHY magnetics, internal versus external termination requirements, thermal conditions, and the exact pin assignments for the 64-QFN footprint.

⚙️

Process and Factory Automation Hub

The KSZ8794CNXIC can act as the Ethernet aggregation point in a process or factory automation hub. Local equipment uses the three 10/100 Mbps copper ports, and plant infrastructure or an edge controller receives traffic through the Gigabit uplink. A Layer 2 managed switch is appropriate when the supervising controller requires port-level configuration and status information. The KSZ8794CNXIC's RGMII, MII, and RMII choices support different host-controller arrangements, including processor- and FPGA-based systems. Because industrial deployments can impose stricter temperature, surge, isolation, and regulatory requirements, engineers should confirm those specifications in the manufacturer datasheet and apply the KSZ8794CNX hardware design checklist before layout release.

🧩

Secure Edge and IoT Gateway

The KSZ8794CNXIC is appropriate for an IoT or secure-edge gateway that must collect traffic from several local wired endpoints and forward it over a Gigabit uplink. The three 10/100 Mbps copper ports provide basic device connectivity, while the managed switch supports a Layer 2 architecture commonly used by embedded network software. Its configurable uplink can connect to an application processor through RMII for a reduced pin-count design, MII for conventional separated clocking, or RGMII for higher-bandwidth parallel signaling. According to Microchip, the device targets cost-sensitive applications and emphasizes low power use, internal biasing, and on-chip termination. Validate security-control firmware, thermal margins, and network timing before deployment.

What is the Microchip KSZ8794CNXIC?
The Microchip KSZ8794CNXIC is a Layer 2 managed Ethernet switch with three 10/100 Mbps copper ports and one 10/100/1000 Mbps Gigabit uplink. It uses a 64-QFN 8 mm by 8 mm package and supports RGMII, MII, and RMII uplink configurations. According to the Microchip KSZ8794 product page and manufacturer datasheet, the device is intended for cost-sensitive systems requiring integrated copper switching and a flexible Gigabit uplink.
How many Ethernet ports does the KSZ8794CNXIC provide?
The KSZ8794CNXIC provides four Ethernet-facing ports in total: three 10/100 Mbps copper ports and one 10/100/1000 Mbps uplink. The hardware design checklist confirms that Ports 1 through 3 are copper ports and Port 4 is the configurable uplink. According to Microchip documentation, Port 4 supports RGMII, MII, and RMII, enabling the switch to connect with different host-controller architectures.
Which host interfaces are supported by the KSZ8794CNXIC uplink?
The KSZ8794CNXIC uplink supports RGMII, MII, and RMII. RGMII provides a high-speed parallel interface for Gigabit connectivity, while MII and RMII support lower-speed legacy or reduced-pin host connections. According to the KSZ8794CNX Hardware Design Checklist, the uplink is configurable, so the final interface selection should be matched to the host processor or FPGA timing and board constraints.
Where can I download the KSZ8794CNXIC datasheet PDF?
The official KSZ8794CNX datasheet PDF is available from Microchip's document server at the datasheet_url on this page. It is titled "Integrated 4-Port 10/100 Managed Ethernet Switch with Gigabit RGMII/MII/RMII Interface." Use the manufacturer copy for final electrical characteristics, timing, pin descriptions, register details, and recommended application circuits because third-party copies may not reflect the latest revision.
Where can I find the KSZ8794CNXIC pinout?
The KSZ8794CNXIC pinout is in the pin-description section of the official Microchip manufacturer datasheet. The component uses a 64-QFN 8 mm by 8 mm package, so the schematic and layout should be assigned from the datasheet's exact numbered pin table rather than from a generic 64-pin diagram. Check the exposed-pad connection and ground requirements directly against the current datasheet before PCB release.
What applications suit the KSZ8794CNXIC managed Ethernet switch?
The KSZ8794CNXIC suits industrial controllers, residential gateways, embedded equipment, and network appliances that need three local 10/100 Mbps connections plus a Gigabit uplink. According to Microchip, the part targets cost-sensitive applications and combines internal biasing, on-chip termination, and low power consumption. The appropriate configuration depends on whether the host uses RGMII, MII, or RMII and on the required copper-port implementation.
What is the difference between RGMII, MII, and RMII on the KSZ8794CNXIC?
RGMII, MII, and RMII are different host-side serial-interface arrangements supported by the KSZ8794CNX uplink. RGMII supports a wide, high-speed parallel connection; MII uses separate clock and data signals; RMII reduces the signal count through a more compact interface. According to the Microchip hardware checklist, Port 4 is configurable, allowing implementation choice to follow host timing, pin availability, and PCB-complexity requirements.
What is the best drop-in replacement for the KSZ8794CNXIC?
No verified pin-to-pin drop-in replacement for the exact KSZ8794CNXIC is identified in the available cross-reference results. A valid replacement must match the 64-QFN 8 mm by 8 mm footprint, preserve all 64 electrical connections, support the same RGMII/MII/RMII uplink, and provide equivalent Layer 2, copper-port, and management functions. Do not treat a merely similar four-port Ethernet switch as a drop-in substitute.
Can a KSZ8794CNXIC be replaced by another four-port Ethernet switch?
A functionally similar four-port Ethernet switch cannot be assumed to replace the KSZ8794CNXIC without a footprint and register-level review. The replacement must retain the 64-QFN 8 mm by 8 mm pinout, exposed-pad arrangement, power architecture, copper PHY behavior, and selected RGMII/MII/RMII host interface. The available cross-reference results do not establish a verified drop-in alternative, so PCB adaptation may be necessary.
When should I choose the KSZ8794CNXIC over a generic Ethernet switch?
Choose the KSZ8794CNXIC when a design needs three 10/100 Mbps copper ports, one Gigabit uplink, and configurable RGMII/MII/RMII host connectivity in a 64-QFN package. It is particularly relevant to cost-sensitive industrial and residential systems. According to Microchip, integrated biasing, on-chip termination, and low power consumption reduce implementation burden, but exact magnetics, termination, and timing requirements still require datasheet review.
Is the KSZ8794CNXIC suitable for an industrial controller?
The KSZ8794CNXIC is suitable for many industrial-controller Ethernet architectures because it provides Layer 2 managed switching, three 10/100 Mbps copper ports, and one Gigabit uplink. The manufacturer design checklist specifically supports development of new KSZ8794CNX-based equipment. Final suitability depends on the device's detailed electrical limits, operating-temperature requirements, isolation strategy, magnetics, and environmental certification for the target equipment.
Where can I buy the KSZ8794CNXIC online?
Use the Request a Quote form on this page to request the KSZ8794CNXIC and current commercial terms. Microchip Direct listed the exact MPN as in stock with 84 units and a partial-tray configuration in the cited result, but inventory and lead time change continuously. The form is the appropriate route for current availability, minimum order quantity, delivery, and quotation requirements.
What is the price of the KSZ8794CNXIC?
Current pricing for the KSZ8794CNXIC should be requested through the Request a Quote form on this page. The available listing results do not expose a qualifying quantity-break price table for the exact MPN, so no stale unit figure is presented as a current offer. The form can provide a transaction-specific quotation, while the structured pricing fields on this page remain empty until a qualifying current listing is available.
Is the KSZ8794CNXIC in stock and what is its lead time?
Microchip Direct's cited result reported 84 units of KSZ8794CNXIC available as a partial tray, with an estimated factory lead time of 15 weeks for additional supply. Inventory and delivery dates can change without notice, so request a current quotation and production schedule through the Request a Quote form on this page. Confirm the package configuration and order quantity with the supplier before committing the BOM.
What are the key specifications engineers should know about the KSZ8794CNXIC?
The KSZ8794CNXIC is a 64-QFN managed Layer 2 Ethernet switch with three 10/100 Mbps copper ports, one 10/100/1000 Mbps uplink, and RGMII/MII/RMII host-interface support. According to the Microchip datasheet and hardware design checklist, it also uses internal biasing and on-chip termination for a cost-sensitive, low-power design. Pin mapping, electrical limits, clocking, management registers, and layout constraints should be confirmed in the manufacturer documentation.
Does the KSZ8794CNXIC comply with RoHS and REACH?
The available product information identifies the KSZ8794CNXIC as RoHS compliant, while its REACH declaration status is not established by the listed information. According to Microchip's environmental and material declaration resources, formal compliance should be confirmed for the exact ordering code and current production revision. Automotive qualification is not indicated because the KSZ8794CNXIC is positioned for industrial, residential, and cost-sensitive networking equipment rather than AEC-Q100 applications.

工程參考資料,適用於 KSZ8794CNXIC — 比較、設計指引及合規資訊。

選型指南

Choose the KSZ8794CNXIC when a system needs exactly three 10/100 Mbps copper connections and one 10/100/1000 Mbps uplink, particularly in a cost-sensitive industrial controller, residential gateway, or embedded appliance. Its managed Layer 2 architecture, configurable RGMII/MII/RMII uplink, internal biasing, and on-chip termination can reduce implementation complexity. The MPN is most appropriate when the host can support one of these uplink modes and the board can implement the required Ethernet magnetics, power rails, reference clock, and 64-QFN layout.

Do not select it for a four-port all-Gigabit design, a design requiring more than three copper ports, or a host that cannot support RGMII, MII, or RMII. No verified drop-in replacement was identified in the available cross-reference results, so changing manufacturers should be treated as a redesign until the footprint, exposed pad, supply rails, PHY behavior, management registers, and host timing are proven equivalent. Use the KSZ8794CNX Hardware Design Checklist and current errata before release.

與替代品比較

參數 本產品
Brand Microchip Technology
Package 64-QFN, 8 mm x 8 mm
Managed Layer Layer 2
Copper Port Count 3 ports
Copper Port Speed 10/100 Mbps
Uplink Port Count 1 port
Uplink Port Speed 10/100/1000 Mbps
Host Interface Options RGMII, MII, RMII
Termination On-chip termination
Design Focus Cost-sensitive, low-power applications

主要差異化特點

  • Combines three copper ports with a configurable Gigabit-class uplink (對比Generic unmanaged four-port copper switch)
  • Supports three host interface configurations (對比Fixed-interface Ethernet switch)
  • Integration reduces auxiliary circuit requirements (對比Discrete Ethernet switch and PHY implementation)
  • Compact package supports compact equipment (對比Larger-package managed Ethernet switch)

設計說明

Base the PCB layout on the KSZ8794CNX Hardware Design Checklist and the current manufacturer datasheet. Treat the 64-QFN footprint, exposed pad, supply connections, reference clocks, and high-speed uplink routes as one constrained design area. Keep RGMII or MII timing paths short, control return-current paths, and follow the manufacturer's recommended component placement and decoupling arrangement before making independent impedance or spacing changes.

Do not finalize supply rails, decoupling, or power sequencing from the general feature description alone. Confirm the required core and interface voltages, current limits, tolerance, startup behavior, and exposed-pad connection in the manufacturer datasheet. The KSZ8794CNX's low-power focus and internal biasing can simplify a design, but external rail quality still determines Ethernet clock and signal reliability.

Check the applicable KSZ87xx silicon errata and data-sheet clarification before freezing the design. The silicon revision can be identified from the device's top marking, and some documented clarifications may affect register interpretation or implementation. Pair that review with the hardware design checklist so the schematic, firmware configuration, magnetics selection, and PCB layout all use the same revision-specific requirements.

Select RGMII, MII, or RMII according to host timing and routing constraints rather than treating the interfaces as electrically interchangeable. RGMII uses a wide high-speed signal group, while RMII favors a smaller host connection and MII follows a more conventional separated clock-and-data arrangement. Follow the manufacturer's clock, trace-length, grounding, and decoupling guidance for the selected mode and preserve signal integrity through the complete host-to-switch path.

合規資訊

RoHS
Compliant
REACH
Unknown
AEC-Q100
Not Applicable
無鉛
Unknown
無鹵
Unknown
衝突礦產
Unknown

RoHS compliance is identified by the product information. REACH, lead-free status, halogen-free status, and conflict-minerals status are not established for the exact ordering code.

相關搜尋

KSZ8794CNXIC KSZ8794CNXIC datasheet KSZ8794CNXIC datasheet pdf KSZ8794CNXIC pinout KSZ8794CNXIC 64-QFN KSZ8794CNXIC RGMII MII RMII KSZ8794CNXIC equivalent KSZ8794CNXIC replacement KSZ8794CNXIC hardware design checklist KSZ8794CNXIC price KSZ8794CNXIC stock Microchip KSZ8794CNXIC KSZ8794CNXIC managed Ethernet switch KSZ8794CNXIC industrial controller

相關元件與詞彙

Microchip Technology KSZ8794CNXIC KSZ8794CNX KSZ8794 Ethernet switch managed Ethernet switch Layer 2 switch Ethernet interface IC 10/100BASE-T/TX Gigabit Ethernet RGMII MII RMII 64-QFN QFN family surface mount SMD internal biasing on-chip termination industrial controller residential gateway network appliance RoHS KSZ87xx silicon errata hardware design checklist
快速報價 RFQ
請填寫完整詳細資料 — 我們的業務團隊將於 24 小時內回覆
料號 製造商 封裝 QTY 目標價格 小計
✓
報價已提交!

我們將於 24 小時內回覆您的電子郵件

1
詢價已提交
2
已收到報價
3
已下單
4
付款
5
已出貨
6
已送達
檢視詢價單詳情