LM224KAD - 4-Channel 32V Op Amp | Texas Instruments
MPN: LM224KAD ✓ فعالLM224KAD جائزہ
An operational amplifier is an analog building block that uses high-gain differential amplification to compare an inverting input with a non-inverting input. When negative feedback is applied, the amplifier adjusts its output to reduce the difference between those inputs. The LM224 family belongs to the broader operational amplifier, analog signal-conditioning, and semiconductor hierarchies, providing a practical way to buffer sensors, amplify small signals, and implement general analog control functions.
Four independent amplifier channels are integrated into one package, reducing board area in designs requiring multiple analog functions. The 1.2 MHz gain-bandwidth product supports common low-frequency signal-conditioning tasks, while the wide 3 V to 32 V operating range accommodates single 5 V, 12 V, 24 V, and ±15 V systems. A 14-pin SOIC provides a familiar surface-mount footprint for conventional PCB assembly and prototype rework. The product listing identifies 2 kV ESD protection, improving handling tolerance in applications exposed to electrostatic discharge.
The LM224 architecture supports operation from a single positive supply or split supplies, allowing the same amplifier family to serve industrial control, instrumentation, and test-equipment designs. Its low-power general-purpose positioning makes it especially useful when four amplifiers are required but precision, rail-to-rail input/output, or very high bandwidth is not required. Input and output limits must still be respected, and the unused amplifier channel should be configured according to the manufacturer’s recommended practice rather than left floating.
Typical uses include 24 V industrial sensor interfaces, temperature-transducer amplification, low-frequency active filters, actuator-signal conditioning, and instrumentation buffers. The wide supply range is particularly useful where the same board must operate across multiple nominal rails. In applications using ±15 V supplies, the device operates near the stated ±16 V capability, while designers should preserve margin for load regulation and transient behavior.
When laying out a design, place input and feedback components close to the corresponding amplifier pins to minimize parasitic feedback and noise pickup. Decoupling capacitors should connect to a low-impedance ground plane, and unused channels need stable biasing. Input common-mode and output swing limits must be checked against the actual supply voltages because the LM224 is not a rail-to-rail amplifier.
This page combines the exact LM224KAD order information, verified product attributes, family-level alternatives, and practical circuit-placement guidance. It also explains where the LM224 fits among general-purpose quad operational amplifiers, helping engineers distinguish it from higher-precision, low-noise, rail-to-rail, or wider-bandwidth amplifier families before making a drop-in sourcing decision.
کے لیے ڈراپ اِن متبادل LM224KAD — یکساں پیکیج، پن سے پن مطابقت پذیر۔ مختلف پیکیج والے پرزے جن کے لیے PCB دوبارہ کام درکار ہو، شامل نہیں ہیں۔
اس سیریز میں مختلف ورژن
اسی سیریز کے ماڈلز جو ڈراپ اِن مطابقت رکھتے ہیں LM224KAD (یکساں فارم فیکٹر اور فٹ پرنٹ) — میں مختلف Package, Product Type, Mounting Type, Supply Configuration, Amplifier Type.
LM224DG4
✅ ڈراپ-اِنقیمت کے لیے رابطہ کریں
ڈیٹا شیٹ دیکھیں →LM224KDR
✅ ڈراپ-اِنقیمت کے لیے رابطہ کریں
ڈیٹا شیٹ دیکھیں →LM224AD
✅ ڈراپ-اِنقیمت کے لیے رابطہ کریں
ڈیٹا شیٹ دیکھیں →LM224ADR
✅ ڈراپ-اِنقیمت کے لیے رابطہ کریں
ڈیٹا شیٹ دیکھیں →LM224KAD زیادہ سے زیادہ ریٹنگز اور برقی خصوصیات
| Amplifier Type | General-purpose operational amplifier |
| Number of Channels | 4 channels |
| Single-Supply Voltage Range | 3 V to 32 V |
| Dual-Supply Voltage Range | ±16 V |
| Typical Gain-Bandwidth Product | 1.2 MHz |
| ESD Protection | 2 kV |
| پیکیج | 14-pin SOIC |
| پن کی تعداد | 14 pins |
| ماؤنٹنگ ٹائپ | Surface mount |
| Shipping Package | Tube |
| Product Class | Standard general-purpose amplifier |
| Temperature Grade | Industrial grade |
| Input Type | Differential input |
LM224KAD tube پن کنفیگریشن گائیڈ
LM224KAD (tube پیکیج) کے لیے پن کنفیگریشن۔ اس اینالاگ کمپوننٹ میں اِن پٹ، آؤٹ پٹ اور پاور سپلائی پنز شامل ہیں۔ آفسیٹ نل، کمپنسیشن اور اِن ایبل پن کنفیگریشنز کے لیے مینوفیکچرر کے ڈیٹا شیٹ سے رجوع کریں۔ سگنل کنڈیشننگ اور ایمپلیفائر سرکٹس کے لیے مثالی۔
کے لیے تفصیلی پن آؤٹ ڈیٹا دستیاب نہیں LM224KAD.
رجوع کریں ڈیٹا شیٹ مکمل پن کنفیگریشن کے لیے۔
عام استعمالات
LM224KAD کے لیے موزوں ہے 6 ایپلیکیشنs: Industrial Sensor Signal Conditioning, Temperature Transducer Amplification, Active Audio and Communications Filters, Control-System Analog Outputs, Portable Test and Measurement Equipment, Power-Supply and Battery Monitoring.
Industrial Sensor Signal Conditioning
The LM224KAD fits industrial sensor interfaces that operate from a 24 V control rail and require several low-frequency analog channels on one board. Its four independent amplifier sections can buffer thermocouple, resistive, pressure, or level-sensor signals before conversion, while the 3 V to 32 V single-supply range provides headroom above a nominal 24 V rail. The 1.2 MHz gain-bandwidth product is appropriate for signals well below the amplifier’s useful closed-loop bandwidth. Because LM224KAD is an industrial-grade ordering option, engineers should still verify its exact temperature limits, input common-mode range, offset voltage, and output-swing limits for the installed enclosure.
تجویز کردہ
Temperature Transducer Amplification
The LM224KAD can amplify the small differential output of resistive temperature sensors when the system uses one supply rail and requires several channels. Each amplifier can be configured as a non-inverting or inverting stage with external resistors, and the 32 V maximum supply capability accommodates industrial excitation and signal-conditioning rails. Its 1.2 MHz typical gain-bandwidth product is substantially faster than many low-frequency temperature-measurement systems require. Designers should calculate resistor noise and offset contributions for the desired gain, then confirm that input and output voltages remain inside the device's specified common-mode and swing limits.
تجویز کردہ
Active Audio and Communications Filters
LM224KAD is suitable for low-frequency active filtering in audio, communications, and instrumentation systems where four channels are needed in a common package. Its 1.2 MHz typical gain-bandwidth product supports stages whose closed-loop bandwidth remains well below the unity-gain limit, while the dual-supply capability reaches ±16 V for bipolar signal paths. The amplifier is a general-purpose choice rather than a dedicated low-noise audio part, so noise, distortion, slew rate, and input-voltage-range requirements should be checked before using it in a high-fidelity chain. External resistors and capacitors determine the filter response and should be selected against the complete gain-bandwidth behavior.
تجویز کردہ
Control-System Analog Outputs
The LM224KAD can condition low-level control signals in industrial panels, actuator interfaces, and analog I/O modules powered from 12 V or 24 V rails. Four channels reduce the component count when a board requires voltage buffers, error amplifiers, comparators with hysteresis, or simple active drive stages. Its 32 V supply capability leaves useful margin in 24 V systems, while operation down to 3 V permits use in lower-voltage control subsections. Output-current capability and saturation behavior must be checked against the load. For signals that must reach the positive supply rail, include an output-limiting network or select a rail-to-rail amplifier instead.
تجویز کردہ
Portable Test and Measurement Equipment
LM224KAD works well in bench instruments and field test equipment that need several general-purpose analog channels for source buffering, differential measurement, and gain stages. The 14-SOIC package is straightforward to assemble and rework, and the wide 3 V to 32 V supply range permits use in both compact battery-derived systems and higher-voltage laboratory interfaces. A 1.2 MHz bandwidth is useful for low- and mid-frequency instrumentation but not for high-speed waveform capture. Designers should verify input bias current, offset voltage, common-mode range, and output drive against the probe, sensor, or test network before finalizing the front end.
تجویز کردہ
Power-Supply and Battery Monitoring
The four channels in LM224KAD can monitor several low-voltage signals in a power-conversion or battery-management system, including cell voltages, feedback nodes, and current-shunt outputs. The wide supply range allows the amplifier to operate from a supervisory rail while sensing signals within its valid input range, and the quad package consolidates several monitoring paths. Because the LM224 is a general-purpose amplifier, its input common-mode range and output swing must be checked carefully when cell voltages approach the positive rail. A suitable design should also account for input bias current and any leakage through high-impedance battery-monitoring nodes.
تجویز کردہ
تجویز کردہ پروڈکٹس کا خلاصہ
کے لیے انجینئرنگ ریفرنس ڈیٹا LM224KAD — موازنہ، ڈیزائن رہنمائی، اور تعمیل کی معلومات۔
انتخاب کی گائیڈ
متبادلات کے ساتھ موازنہ
| پیرامیٹر | یہ پروڈکٹ | LM224DG4 | LM224KDR | LM224AD | LM224ADR |
|---|---|---|---|---|---|
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Package | 14-SOIC | 14-SOIC - same | 14-SOIC - same | 14-SOIC - same | 14-SOIC - same |
| Amplifier Configuration | Quad general-purpose operational amplifier | Quad general-purpose operational amplifier | Quad general-purpose operational amplifier | Quad general-purpose operational amplifier | Quad general-purpose operational amplifier |
| Number of Channels | 4 channels | 4 channels | 4 channels | 4 channels | 4 channels |
اہم امتیازی خصوصیات
- Four general-purpose amplifier channels in one 14-SOIC package (بمقابلہLM224DG4)
- Wide single- and dual-supply operating capability (بمقابلہLM224AD)
- Improved 2 kV ESD protection for industrial handling environments (بمقابلہLM224ADR)
- Practical bandwidth for low-frequency multi-channel analog conditioning (بمقابلہLM224KDR)
ڈیزائن نوٹس
Place each amplifier's feedback resistors, input resistors, and optional compensation components close to the corresponding LM224KAD pins. Keep output routing away from high-impedance input nodes to reduce parasitic oscillation and sensitivity to board contamination. Connect supply-decoupling capacitors to the ground plane with short, low-inductance paths rather than routing them around the package footprint.
Do not assume that the output can swing to either supply rail. Before using LM224KAD with a 3 V, 5 V, or 12 V supply, check the output-voltage headroom under the intended load and include it in the logic-level design. Also bias every unused amplifier channel according to the manufacturer guidance; leaving an unused input floating can increase noise, disturb supply current, or produce unstable output behavior.
Use a continuous ground plane beneath and around the SOIC, and provide a low-impedance connection from the power and ground pins to the board's supply network. Keep analog input traces short and isolate them from switching-node and high-current return paths. For precision gain stages, use grounded or shielded input structures and avoid routing beneath connectors or digital clock lines that can inject noise through parasitic capacitance.
The LM224KAD can operate from 3 V to 32 V, but that range does not imply identical performance on every rail. Derive the bias currents from the actual single or dual supply, verify input common-mode range and output swing, and leave transient margin below the 32 V maximum. A regulated rail with adequate decoupling is preferable when analog signal integrity is more important than minimum component count.
تعمیل کی معلومات
No specific RoHS, REACH, lead-free, halogen-free, conflict-minerals, or automotive-qualification statement was identified for the exact LM224KAD order code. The device is listed as industrial grade, which does not by itself establish AEC-Q100 qualification.