Texas Instruments

LM224KDE4 - Quad 30V 1.2MHz Op Amp | Texas Instruments

MPN: LM224KDE4 ✓ فعال
30 V Vdss 14-SOIC (0.154 inch, 3.90 mm width) Package
MOQ: 1 |

LM224KDE4 جائزہ

Texas Instruments LM224KDE4 is a general-purpose quadruple operational amplifier with four independent amplifiers, a 30 V supply rating, 1.2 MHz gain-bandwidth product, and improved 2 kV ESD protection. It is packaged in a 14-pin SOIC and is specified for operation from -25°C to +85°C.

An operational amplifier is an analog signal-conditioning integrated circuit that compares two input voltages and amplifies the difference between them. Its broader hierarchy is operational amplifier -> voltage-amplifier IC -> analog amplifier -> amplifier IC -> semiconductor. The LM224K combines four general-purpose amplifiers in one package, allowing a compact circuit to perform buffering, amplification, filtering, level shifting, and feedback-control functions.

The principal features of the LM224KDE4 include four independent amplifier channels, operation from a single or split supply, a 30 V maximum supply rating, and a 1.2 MHz gain-bandwidth product. The improved 2 kV ESD protection helps the device tolerate electrostatic discharge exposure, while the -25°C to +85°C operating range supports industrial and extended-temperature applications.

Each channel uses a differential input stage, high-gain voltage-amplification stage, and output stage optimized for general-purpose analog signal paths. Because the four amplifiers share a common supply architecture but operate independently, engineers can use them for simultaneous sensing, buffering, error amplification, or active filtering when sufficient decoupling is provided.

Typical uses include industrial sensor interfaces, low-frequency active filters, transducer conditioning, control-loop error amplifiers, and general instrumentation. The 14-pin SOIC is also convenient for prototypes and repair assemblies because its four amplifiers can replace separate single or dual amplifier packages when board area is limited.

For reliable operation, place the supply bypass capacitor close to the positive and ground pins and route high-current return paths away from sensitive input nodes. Check output swing, input common-mode range, load capability, and stability against the required signal amplitude before closing the feedback loop.

This page combines manufacturer specifications, lifecycle information, package guidance, structured comparisons, and practical replacement guidance to support component selection, PCB layout, sourcing, and second-source qualification.

کے لیے ڈراپ اِن متبادل LM224KDE4 — یکساں پیکیج، پن سے پن مطابقت پذیر۔ مختلف پیکیج والے پرزے جن کے لیے PCB دوبارہ کام درکار ہو، شامل نہیں ہیں۔

اس سیریز میں مختلف ورژن

اسی سیریز کے ماڈلز جو ڈراپ اِن مطابقت رکھتے ہیں LM224KDE4 (یکساں فارم فیکٹر اور فٹ پرنٹ) — میں مختلف Package, Mounting Type, Architecture, Operating Temperature Range, Product Type.

Texas Instruments
Package: 14-pin SOIC
Mounting Type: Surface-mount SOIC
Architecture: Four independent high-gain, frequency-compensated amplifiers
موازنہ کریں LM224KDE4 →
Texas Instruments
Package: 14-SOIC
Product Type: Standard general-purpose operational amplifier
موازنہ کریں LM224KDE4 →

LM224KADR

✅ ڈراپ-اِن
📦 14-SOIC
Same 14-SOIC footprint and four-channel configuration; published comparison identifies consistent 1.2 MHz performance and no terminal changes

📋 حوالہ جاتی متبادل (کیٹلاگ میں نہیں)

LM224ADR

✅ ڈراپ-اِن ⚠️ تفصیلات غیر تصدیق شدہ
Texas Instruments
📦 14-SOIC
Quad general-purpose operational amplifier · 4 circuits · Four independent high-gain, frequency-compensated amplifiers · 1.2 MHz · 0.5 V/µs · 3 mV · 30 V · ±1.5 V to ±16 V

قیمت کے لیے رابطہ کریں

ڈیٹا شیٹ دیکھیں →

LM224DR

✅ ڈراپ-اِن ⚠️ تفصیلات غیر تصدیق شدہ
Texas Instruments
📦 14-SOIC
Standard general-purpose operational amplifier · 4 circuits · 14-SOIC · Surface mount

✓ اسٹاک میں

$0.1641 / یونٹ

ڈیٹا شیٹ دیکھیں →

LM224DG4

✅ ڈراپ-اِن ⚠️ تفصیلات غیر تصدیق شدہ
Texas Instruments
📦 14-SOIC
Quadruple operational amplifier · 4 circuits · 3 V to 32 V · 14-pin SOIC · Surface mount · Standard general-purpose amplifier · 4 · Single or split supply

قیمت کے لیے رابطہ کریں

ڈیٹا شیٹ دیکھیں →

LM224KDR

✅ ڈراپ-اِن ⚠️ تفصیلات غیر تصدیق شدہ
Texas Instruments
📦 14-SOIC
Quad general-purpose operational amplifier · 4 circuits · 30 V · 1.2 MHz · 2 kV · -25°C to +85°C · 14-pin SOIC (D) · 0.154 in (3.90 mm)

قیمت کے لیے رابطہ کریں

ڈیٹا شیٹ دیکھیں →

LM224KDE4 زیادہ سے زیادہ ریٹنگز اور برقی خصوصیات

Amplifier Type General-purpose operational amplifier
Number of Channels 4 channels
Architecture Quadruple, four independent amplifiers
Maximum Supply Voltage 30 V
Gain-Bandwidth Product 1.2 MHz
ESD Protection 2 kV
آپریٹنگ درجہ حرارت رینج -25°C to +85°C
پیکیج 14-SOIC (0.154 inch, 3.90 mm width)
پنز کی تعداد 14 pins
ماؤنٹنگ ٹائپ Surface mount
Terminal Form Gull wing
Package Shape Rectangular
Supply Configuration Single or split supply

LM224KDE4 پن کنفیگریشن

SOIC-14 (3.9mm) Package Pinout Diagram SOIC-14 14-pin small outline IC, 3.9x8.7mm, P1.27mm, JEDEC MS-012. Pin 1 by chamfer. 1 14 2 13 3 12 4 11 5 10 6 9 7 8 SOIC-14 (3.9mm)
پن 1 OUT1 — Amplifier 1 output
پن 2 IN1- — Amplifier 1 inverting input
پن 3 IN1+ — Amplifier 1 non-inverting input
پن 4 V- — Negative supply connection
پن 5 IN2+ — Amplifier 2 non-inverting input
پن 6 IN2- — Amplifier 2 inverting input
پن 7 OUT2 — Amplifier 2 output
پن 8 OUT3 — Amplifier 3 output
پن 9 IN3- — Amplifier 3 inverting input
پن 10 IN3+ — Amplifier 3 non-inverting input
پن 11 V+ — Positive supply connection
پن 12 IN4+ — Amplifier 4 non-inverting input
پن 13 IN4- — Amplifier 4 inverting input
پن 14 OUT4 — Amplifier 4 output

عام استعمالات

LM224KDE4 کے لیے موزوں ہے 6 ایپلیکیشنs: Industrial Sensor Signal Conditioning, Active Audio and Low-Frequency Filters, Transducer and Bridge Excitation Interfaces, Power Supply Control and Feedback Loops, Test and Measurement Buffering, Automotive and Equipment Control Modules.

🏭

Industrial Sensor Signal Conditioning

The LM224KDE4 is suitable for conditioning low-bandwidth industrial sensor signals because four independent amplifiers can buffer inputs, amplify small differentials, and form active filter stages within one 14-SOIC package. Its 1.2 MHz gain-bandwidth product supports general-purpose signal paths operating well below megahertz bandwidth, while the 30 V supply rating accommodates higher-voltage industrial interfaces. The 2 kV ESD rating adds useful device-level robustness near external connectors, although system-level protection remains necessary. Designers should verify input common-mode range, output swing, and offset behavior against the sensor output before selecting gain values.

🎧

Active Audio and Low-Frequency Filters

The LM224KDE4 can implement active low-pass, high-pass, and band-pass filters in audio, communications, and control circuits where four channels reduce board area. A 1.2 MHz gain-bandwidth product gives ample loop-gain margin for many sub-audio-band filters, allowing practical closed-loop operation well below the unity-gain frequency. The four independent amplifiers support separate filter stages or stereo pairs. Stable results depend on suitable resistor and capacitor values, adequate supply bypassing, and keeping input and output nodes away from high-current return paths. Prototype the filter and verify gain, phase margin, output range, and channel-to-channel behavior before production.

🧩

Transducer and Bridge Excitation Interfaces

The LM224KDE4 fits instrumentation amplifiers, bridge-sensor front ends, and programmable transducer interfaces requiring several buffered or gain-shaping stages. Its four-channel organization permits an instrumentation-amplifier core, output filter, and auxiliary buffer within a single package, while the 30 V maximum supply rating supports industrial excitation levels. At 1.2 MHz gain-bandwidth product, the device is intended for low- or moderate-bandwidth measurement paths rather than high-speed instrumentation. Validate common-mode headroom, excitation voltage, input bias-current effects, and output drive against the transducer and bridge tolerances before finalizing the gain network.

⚡

Power Supply Control and Feedback Loops

The LM224KDE4 is appropriate for slow error-amplifier and feedback-control roles in linear power supplies, regulated outputs, and industrial power modules. Four channels can implement a control amplifier, output buffer, current-loop amplifier, and auxiliary monitoring channel in one package. Its 30 V supply rating is useful when the feedback network operates above typical low-voltage logic levels, and the 1.2 MHz gain-bandwidth product is sufficient for many control loops whose bandwidth is deliberately limited for noise and stability. Compensation must be designed around the amplifier gain-bandwidth behavior, output loading, and the plant delay; otherwise oscillation or slow settling may occur.

🖥️

Test and Measurement Buffering

The LM224KDE4 can buffer source impedances and condition probe signals in general-purpose test and measurement equipment. Four independent channels allow repeated buffering without requiring separate amplifier packages, and the 1.2 MHz gain-bandwidth product is useful for low-frequency measurement systems with moderate source impedance. The 14-SOIC format simplifies assembly in laboratory instruments and automated test fixtures. Designers should account for amplifier input bias current, capacitive loading, settling behavior, and output-current limits when driving long cables or high-capacitance networks. Isolation, attenuation, and high-voltage protection must be implemented separately because the device is not an instrumentation-protection barrier.

🚗

Automotive and Equipment Control Modules

The LM224KDE4 can support low-frequency control, conditioning, and interface functions in industrial equipment and non-safety automotive auxiliary circuits. Its four independent general-purpose amplifiers provide flexible routing of error signals, sensor outputs, and actuator references, while the -25°C to +85°C range covers many commercial and extended-temperature environments. The 2 kV ESD capability improves robustness but does not qualify the device for a specific automotive functional-safety or AEC-Q100 requirement by itself. Confirm the exact ordering qualification, automotive temperature requirement, transient levels, and system protection scheme before using the amplifier in a vehicle or safety-related equipment.

What is the operating voltage of LM224KDE4?
The LM224KDE4 supports operation with a maximum supply rating of 30 V and can be used with single or split supplies. According to the Texas Instruments LM224K product page and manufacturer datasheet, the device is designed for general-purpose analog signal conditioning rather than low-voltage-only applications. Designers should still verify the input common-mode range and output swing against their actual supply voltage before use.
What are the key specifications of LM224KDE4 that engineers should know?
The LM224KDE4 is a four-channel general-purpose operational amplifier with a 30 V maximum supply rating, 1.2 MHz gain-bandwidth product, 2 kV ESD protection, and a -25°C to +85°C operating range. It is housed in a 14-pin SOIC. According to the Texas Instruments product page and datasheet, four independent amplifiers in one package reduce component count and simplify PCB layout for instrumentation and control applications.
Where can I download the LM224KDE4 datasheet PDF?
The official LM224K information is available from the Texas Instruments product page at https://www.ti.com/product/LM224K, which provides datasheets, ordering information, and quality documentation. The LM224KDE4 ordering code identifies the 14-SOIC package. Use the document associated with LM224K from the manufacturer because package, temperature, and ordering suffixes determine the applicable part configuration.
Where can I find the LM224KDE4 pinout?
The LM224KDE4 pinout is documented in the manufacturer datasheet under the pin-configuration and pin-description tables. The device uses a conventional 14-pin SOIC with four independent operational amplifiers. Assign signals using the numbered pin-description table rather than inferring connections from neighboring amplifier packages, and use the selected package diagram when checking PCB orientation.
Is LM224KDE4 suitable for industrial applications?
Yes, the LM224KDE4 is suitable for many industrial applications because Texas Instruments specifies operation from -25°C to +85°C and improved ESD protection of 2 kV. Its four general-purpose channels can implement sensor buffering, low-frequency active filters, and control-loop amplification. For safety- or mission-critical systems, verify the exact qualification requirements and ESD test conditions before release.
What can replace the LM224KDE4?
A suitable replacement must use the same 14-SOIC footprint and maintain the required supply, common-mode, output-swing, frequency, and temperature limits. The LM224KADR is identified as a completely replaceable option because its terminals and package match the target and its main performance characteristics are consistent. Review the manufacturer datasheet and your worst-case operating conditions before approving a substitution.
Is LM224KDE4 the same as LM224ADR?
The LM224KDE4 and LM224ADR belong to the same LM224 family and use a 14-pin SOIC outline, but their orderable temperature and quality options should be checked before treating them as identical. According to Texas Instruments ordering information, suffix differences identify the intended grade or configuration. Confirm operating-temperature range, ESD rating, supply rating, and production qualification against the selected part number.
LM224KDE4 vs LM224KADR - which is better for a 14-SOIC design?
The LM224KADR is the stronger replacement candidate because the published comparison identifies consistent main performance parameters, matching terminals, and matching package, with no replacement changes required. The LM224KDE4 is the specified 30 V, 1.2 MHz, 2 kV-ESD LM224K configuration. Choose the variant whose exact ordering conditions and temperature grade meet the production requirements.
When should I choose LM224KDE4 over LM224KADR?
Choose the LM224KDE4 when its specific orderable temperature, ESD, and quality configuration matches the product requirement and is available through the intended supply channel. Choose LM224KADR when its documented terminal and package compatibility is acceptable and procurement conditions favor that ordering code. For either choice, verify supply voltage, common-mode range, output swing, and load current against the manufacturer datasheet.
Is there a cross-brand pin-compatible equivalent for LM224KDE4?
No cross-brand MPN is established as a drop-in equivalent in the available cross-reference records. A valid replacement must retain the 14-SOIC pin arrangement and satisfy the 30 V supply, 1.2 MHz bandwidth, common-mode, output-swing, and temperature requirements. Use the Request a Quote form on this page when you need an engineering review of a proposed second source, and do not substitute a different package without a PCB redesign.
What is the price of LM224KDE4?
Current commercial terms for LM224KDE4 are obtained through the Request a Quote form on this page. The form lets you request the unit price, stock position, minimum order quantity, and expected lead time for the exact 14-SOIC ordering code. Because availability and commercial terms can change, the page does not publish a static price that could become misleading.
Where can I buy LM224KDE4 online?
Use the Request a Quote form on this page to request LM224KDE4 pricing, stock, minimum order quantity, and lead time for the exact manufacturer ordering code. The component is a four-channel general-purpose operational amplifier in a 14-SOIC package. Include your target quantity, acceptable delivery date, and inspection requirements so the commercial response matches the production plan.
What is the lead time for LM224KDE4?
The current lead time for LM224KDE4 should be requested through the Request a Quote form on this page. Lead time can vary with order quantity, package configuration, quality grade, and market conditions, so it should be confirmed for each purchase rather than treated as a fixed product attribute. Provide the planned order quantity and required delivery date when submitting the request.
Is LM224KDE4 in stock?
Current stock for LM224KDE4 is confirmed through the Request a Quote form on this page. Submit the required quantity and target delivery date to receive an availability response for the exact 14-SOIC ordering code. For production planning, request quantity-break availability and lead time together so partial or split deliveries can be identified before committing the build schedule.
Does LM224KDE4 include ESD protection?
Yes, the Texas Instruments LM224K family is described as having improved 2 kV ESD protection. The LM224KDE4 combines that protection rating with a 30 V maximum supply rating, 1.2 MHz gain-bandwidth product, and -25°C to +85°C operating range. ESD protection reduces sensitivity to electrostatic events but does not replace proper handling, grounding, or external protection at exposed connectors.

کے لیے انجینئرنگ ریفرنس ڈیٹا LM224KDE4 — موازنہ، ڈیزائن رہنمائی، اور تعمیل کی معلومات۔

انتخاب کی گائیڈ

Choose LM224KDE4 for general-purpose analog designs needing four independent amplifiers in a 14-SOIC, operation up to a 30 V supply rating, a 1.2 MHz gain-bandwidth product, and a stated 2 kV ESD rating. LM224KADR is the most direct documented replacement candidate because its terminals, package, and main performance characteristics are reported as consistent, but confirm the exact ordering-grade requirements before substitution. LM224ADR, LM224DR, LM224DG4, and LM224KDR are same-family 14-SOIC options whose suffix-specific temperature and quality requirements must be checked. The LM324KDR offers a related quad-amplifier solution with lower voltage headroom, while LM2902N/PB is appropriate only when two channels are sufficient. For any second source, validate common-mode range, output swing, stability, loading, and temperature limits on the intended board.

متبادلات کے ساتھ موازنہ

پیرامیٹر یہ پروڈکٹ LM224KADR LM224ADR LM224DR LM224DG4 LM224KDR
Brand Texas Instruments Texas Instruments Texas Instruments Texas Instruments Texas Instruments Texas Instruments
Package 14-SOIC 14-SOIC 14-SOIC 14-SOIC 14-SOIC 14-SOIC
Number of Channels 4 channels 4 channels 4 channels 4 channels 4 channels 4 channels
Gain-Bandwidth Product 1.2 MHz 1.2 MHz 1.2 MHz 1.2 MHz 1.2 MHz 1.2 MHz
Supply Configuration Single or split supply Single or split supply Single or split supply Single or split supply Single or split supply Single or split supply
Amplifier Type General-purpose operational amplifier General-purpose operational amplifier General-purpose operational amplifier General-purpose operational amplifier General-purpose operational amplifier General-purpose operational amplifier

اہم امتیازی خصوصیات

  • Documented no-change replacement option (بمقابلہLM224KADR)
  • Four independent amplifiers in one package (بمقابلہLM2902N/PB)
  • Higher supply rating than the related LM324 option (بمقابلہLM324KDR)
  • Improved ESD capability within the LM224 family (بمقابلہLM224ADR)

ڈیزائن نوٹس

Place the positive-supply bypass capacitor directly between the V+ pin and ground, and connect the negative or ground return through a low-impedance path. For split supplies, decouple each supply rail at the device. Keep the capacitor loop short because the four amplifiers can draw transient current when driving capacitive loads. A compact supply-and-ground layout helps prevent output disturbance from appearing as an input signal.

Route each inverting-input trace away from the outputs, supply pins, and other high-impedance input nodes. When an amplifier is configured with a high-gain feedback network, keep the feedback resistor and compensation components close to the relevant input and output pins. This minimizes parasitic capacitance and feedback-loop pickup, which can reduce phase margin or cause oscillation in otherwise stable 1.2 MHz-capable designs.

Do not assume that a matching 14-SOIC footprint guarantees electrical equivalence. Before replacing LM224KDE4, compare maximum supply voltage, input common-mode range, output swing, gain-bandwidth product, slew rate, output-current capability, operating temperature, and ESD rating. Also verify that the alternative uses the same amplifier-to-pin channel arrangement, because package outlines can match while functional assignments differ.

Estimate the maximum signal frequency from the closed-loop gain and the 1.2 MHz gain-bandwidth product, then include additional margin for filter Q, load capacitance, and feedback-component tolerances. For high-Q filters or long feedback loops, prototype the network with realistic loading and probe the phase margin. This is especially important when multiple channels share a board with digital switching circuitry or long unprotected input wiring.

تعمیل کی معلومات

RoHS
Unknown
REACH
Unknown
AEC-Q100
Unknown
لیڈ فری
Unknown
ہیلوجن فری
Unknown
کنفلیکٹ منرلز
Unknown

The available product and distributor information does not establish the requested compliance statuses. Confirm RoHS, REACH, AEC-Q100, lead-free, halogen-free, and conflict-minerals documentation for the selected ordering code before regulatory submission.

ڈیٹا کی تصدیق کی تاریخ: 2026-11-15 — ڈیٹا XAIPART کی کمپوننٹ انجینئرنگ ٹیم کے ذریعے تصدیق شدہ اور ترتیب شدہ

متعلقہ تلاشیں

LM224KDE4 datasheet LM224KDE4 pinout LM224KDE4 datasheet pdf LM224KDE4 specifications LM224KDE4 equivalent LM224KDE4 replacement LM224KDE4 cross reference LM224KDE4 vs LM224KADR LM224KDE4 SOIC-14 footprint LM224KDE4 application circuit Texas Instruments LM224KDE4 LM224KDE4 price LM224KDE4 stock LM224KDE4 30V 1.2MHz amplifier

متعلقہ اجزاء اور اصطلاحات

Texas Instruments LM224KDE4 LM224K LM224KADR LM224ADR LM224DR LM224DG4 LM224KDR LM324KDR LM2902N/PB operational amplifier general-purpose amplifier quad operational amplifier analog signal conditioning voltage-feedback amplifier 14-SOIC SOIC family surface mount SMD gain-bandwidth product ESD protection input common-mode range output swing single supply split supply
فوری کوٹ RFQ
مکمل تفصیلات بھریں — ہماری سیلز ٹیم 24 گھنٹوں میں جواب دے گی
پارٹ نمبر مینوفیکچرر پیکج QTY ہدف قیمت کل رقم
✓
کوٹ جمع ہو گیا!

ہم 24 گھنٹوں کے اندر آپ کے ای میل کا جواب دیں گے

1
RFQ جمع ہو گیا
2
کوٹ موصول ہو گیا
3
آرڈر دے دیا گیا
4
ادائیگی
5
بھیج دیا گیا
6
ڈیلیور شدہ
RFQ تفصیلات دیکھیں