LM2902DR2G - Quad 3-26V Operational Amplifier | onsemi
MPN: LM2902DR2G ✓ فعالLM2902DR2G جائزہ
A general-purpose operational amplifier is a voltage-amplifying active device that uses differential inputs and feedback to control gain, filtering, buffering, and signal conditioning. The quad LM2902 family combines four amplifiers within one semiconductor package, reducing board area and simplifying designs that require multiple independent analog channels. The LM2902DR2G is associated with the onsemi LM2902 family and is identified by distributor listings as a single-supply quad operational amplifier in a 14-SOIC package.
The key device characteristics are the four-amplifier configuration, 3 V to 26 V supply range, 14-SOIC package, and general-purpose single-supply operation. These specifications make the device suitable for industrial control systems, sensor interfaces, low-frequency signal conditioning, audio and communications support circuits, and general instrumentation. Because the LM2902 is a general-purpose amplifier rather than a precision or high-speed part, designers should verify input bias current, output swing, noise, slew rate, and stability requirements against the manufacturer datasheet for the actual operating conditions.
In a typical single-supply design, the LM2902 is powered from a positive supply while the signal source and reference point are biased near ground. Decoupling capacitors should be placed close to the supply pins, and unused amplifier inputs should be biased so that they remain in a defined operating state. Feedback-network values determine gain and bandwidth, so resistor and capacitor tolerances directly influence signal accuracy. The device should also be evaluated for output-current capability and thermal rise when driving capacitive loads or operating at elevated temperatures.
Common uses include sensor signal conditioning, low-level instrumentation, control-loop input stages, active filtering, waveform conditioning, and general-purpose buffering. The 14-SOIC package provides a familiar footprint for designs using standard through-hole assembly, although the exposed thermal behavior and electrical limits remain important at higher ambient temperatures. The LM2902DR2G is therefore best suited to cost-sensitive, low-to-moderate-frequency analog systems where four channels and single-supply convenience matter more than precision or high bandwidth.
This page summarizes the device identity, package, operating range, sourcing information, drop-in alternatives, application guidance, and engineering considerations for engineers evaluating LM2902DR2G. The manufacturer datasheet should be consulted for the complete electrical characteristics, recommended operating conditions, pinout, and application details before final circuit release.
کے لیے ڈراپ اِن متبادل LM2902DR2G — یکساں پیکیج، پن سے پن مطابقت پذیر۔ مختلف پیکیج والے پرزے جن کے لیے PCB دوبارہ کام درکار ہو، شامل نہیں ہیں۔
اس سیریز میں مختلف ورژن
اسی سیریز کے ماڈلز جو ڈراپ اِن مطابقت رکھتے ہیں LM2902DR2G (یکساں فارم فیکٹر اور فٹ پرنٹ) — میں مختلف Amplifier Type, Package, Input Type, Slew Rate, Number of Channels.
LM2902DG
✅ ڈراپ-اِنقیمت کے لیے رابطہ کریں
ڈیٹا شیٹ دیکھیں →NCV2902DR2G
✅ ڈراپ-اِن📋 حوالہ جاتی متبادل (کیٹلاگ میں نہیں)
LM324DR2G
✅ ڈراپ-اِنقیمت کے لیے رابطہ کریں
ڈیٹا شیٹ دیکھیں →LM224DR2G
✅ ڈراپ-اِن📋 حوالہ جاتی متبادل (کیٹلاگ میں نہیں)
LP2902M/NOPB
✅ ڈراپ-اِن📋 حوالہ جاتی متبادل (کیٹلاگ میں نہیں)
LM2902DR2G زیادہ سے زیادہ ریٹنگز اور برقی خصوصیات
| Amplifier Type | General-purpose operational amplifier |
| Number of Channels | 4 |
| Supply Voltage Range | 3 V to 26 V |
| Supply Type | Single supply |
| پیکیج | 14-SOIC |
| ماؤنٹنگ ٹائپ | Surface mount |
| Application Category | Instrumentation, operational amplifiers, buffer amplifiers |
| Input Type | Differential input |
| آپریٹنگ درجہ حرارت رینج | -40 C to +105 C |
| RoHS اسٹیٹس | Compliant |
| REACH Status | Unaffected |
| MSL | 1 (unlimited) |
| AEC-Q100 Qualification | Not applicable |
| پن کی تعداد | 14 |
LM2902DR2G پن کنفیگریشن
| پن 1 | OUT A — Output of amplifier A |
| پن 2 | IN- A — Inverting input of amplifier A |
| پن 3 | IN+ A — Non-inverting input of amplifier A |
| پن 4 | V- — Negative supply or ground connection |
| پن 5 | IN+ B — Non-inverting input of amplifier B |
| پن 6 | IN- B — Inverting input of amplifier B |
| پن 7 | OUT B — Output of amplifier B |
| پن 8 | OUT C — Output of amplifier C |
| پن 9 | IN- C — Inverting input of amplifier C |
| پن 10 | IN+ C — Non-inverting input of amplifier C |
| پن 11 | V+ — Positive supply input |
| پن 12 | IN+ D — Non-inverting input of amplifier D |
| پن 13 | IN- D — Inverting input of amplifier D |
| پن 14 | OUT D — Output of amplifier D |
عام استعمالات
LM2902DR2G کے لیے موزوں ہے 6 ایپلیکیشنs: Sensor Signal Conditioning, Industrial Instrumentation, Control-System Interface, Active Filtering, Audio Interface Conditioning, General-Purpose Buffering.
Sensor Signal Conditioning
LM2902DR2G is suitable for conditioning outputs from resistive, resistive-divider, and low-current sensors. A buffer channel can isolate the sensor from downstream filtering, while another channel provides gain or active offset. The four-channel arrangement allows one device to implement several analog functions in a compact 14-SOIC footprint. Designers should check the input bias current against the sensor’s source impedance, verify that the signal remains inside the input common-mode range, and confirm the output swing at the selected supply voltage.
تجویز کردہ
Industrial Instrumentation
The LM2902DR2G supports general-purpose instrumentation tasks where several low-frequency analog channels must share a single supply. It can provide input buffering, differential amplification, voltage scaling, and active filtering in one package. Its 3 V to 26 V operating range supports low-voltage and industrial supply arrangements, while the 14-SOIC package supports conventional PCB assembly. For instrumentation, preserve analog ground integrity, keep feedback loops compact, and validate offset and bias-current errors against the measurement resolution required by the system.
تجویز کردہ
Control-System Interface
LM2902DR2G can form input conditioning and actuator-drive stages around low-frequency industrial control loops. Its four channels may be assigned to sensor amplification, reference buffering, error amplification, and output buffering. The general-purpose architecture is effective when the loop bandwidth is modest and the circuit must operate from a single supply. Check the output-current capability against actuator interface requirements, add adequate local decoupling, and avoid driving long capacitive loads unless the datasheet stability conditions are met.
تجویز کردہ
Active Filtering
The LM2902DR2G can implement first-order or cascaded active filters in audio, communications, and control systems. Multiple amplifier channels make it convenient to build low-pass, high-pass, or notch stages without using separate packages. Stable operation depends on the selected gain, noise gain, feedback capacitor, and load conditions, so the design should be simulated and checked against the manufacturer’s stability guidance. Keep the filter’s ground return short and place input and feedback components close to the associated amplifier pins.
تجویز کردہ
Audio Interface Conditioning
LM2902DR2G is useful for general audio interface tasks such as input buffering, gain staging, impedance conversion, and simple active filtering. The four-channel device can support multiple signal paths in a 14-SOIC package, although it is a general-purpose amplifier rather than a dedicated low-noise audio part. Verify input-referred noise, distortion, slew rate, and output swing against the audio bandwidth and load. Decouple the supply locally and route audio return current carefully to reduce channel-to-channel coupling.
تجویز کردہ
General-Purpose Buffering
LM2902DR2G provides four general-purpose amplifier channels for buffering high-impedance sources, isolating ADC drivers, and implementing simple gain stages. Buffering reduces source-loading effects when the next circuit stage presents a substantially different impedance. Use a unity-gain configuration for straightforward isolation, and confirm stability with the intended capacitive load. The 14-SOIC package offers four channels in one footprint, but unused inputs should be tied to a defined reference rather than left floating.
تجویز کردہ
تجویز کردہ پروڈکٹس کا خلاصہ
کے لیے انجینئرنگ ریفرنس ڈیٹا LM2902DR2G — موازنہ، ڈیزائن رہنمائی، اور تعمیل کی معلومات۔
انتخاب کی گائیڈ
متبادلات کے ساتھ موازنہ
| پیرامیٹر | یہ پروڈکٹ | LM2902DG | NCV2902DR2G | LM324DR2G | LM224DR2G | LP2902M/NOPB |
|---|---|---|---|---|---|---|
| Package | 14-SOIC | 14-SOIC | 14-SOIC | 14-SOIC | 14-SOIC | 14-SOIC |
| Brand | onsemi | onsemi | onsemi | onsemi | onsemi | Texas Instruments |
| Number of Amplifiers | 4 | 4 | 4 | 4 | 4 | 4 |
اہم امتیازی خصوصیات
- Four general-purpose channels in one 14-SOIC package (بمقابلہLM324DR2G)
- Single-supply operation from 3 V to 26 V (بمقابلہLM224DR2G)
- Established onsemi LM2902 family sourcing path (بمقابلہLP2902M/NOPB)
ڈیزائن نوٹس
Place the LM2902DR2G bypass capacitor directly between the supply pin and the appropriate ground return, keeping the loop short. Route the four amplifier outputs away from sensitive input traces, and place feedback resistors and capacitors close to the corresponding amplifier pins. This reduces parasitic inductance, supply coupling, and feedback-loop pickup.
Do not leave unused amplifier inputs floating. Tie each unused input to a defined reference point while ensuring that the amplifier remains within its input common-mode range. Also verify output swing at the selected supply voltage; a single-supply circuit can leave little headroom at the lower rail even when the nominal output target is modest.
Estimated: calculate amplifier dissipation as the product of supply voltage, output voltage, and output current, then account for the input and output quiescent currents. Confirm that the resulting junction-temperature estimate stays below the manufacturer’s operating limit. The 14-SOIC package and the -40 C to +105 C ambient rating do not remove the need for thermal review at high load.
For higher-impedance sources, compare the LM2902 input bias current with the source impedance because bias current can create a voltage error. For capacitive loads, use the datasheet stability guidance and add an isolation resistor when required. These checks are especially important when the quad device drives ADC inputs, long cables, or switched-capacitor circuits.
تعمیل کی معلومات
The cross-reference listing identifies the LM2902DR2G as RoHS3 compliant, REACH unaffected, and MSL 1. Lead-free, halogen-free, and conflict-minerals status are not stated for the exact MPN.
