LM2903AVQPWRG4 - Dual Comparator | Texas Instruments
MPN: LM2903AVQPWRG4 ✓ فعالLM2903AVQPWRG4 جائزہ
A differential comparator is an analog integrated circuit that compares two input voltages and changes its output state when the difference between those voltages crosses a defined threshold. Within the comparator hierarchy, this device belongs to the general-purpose comparator, analog IC, and semiconductor categories. Its open-collector outputs allow the output stage to sink current while remaining compatible with external pull-up resistors, making it useful for wired logic, relay drivers, and level translation.
The LM2903B family offers low input offset voltage of 0.37 mV, low input bias current of 3.5 nA, supply current of 200 µA per comparator, and a faster response time of 1 µs. The B version is identified by Texas Instruments as a drop-in replacement for LM293, LM393, and LM2903 devices in both A and V grades. It also provides an extended temperature range and an HBM ESD rating of 2 kV.
The device supports operation from 2 V to 36 V with a single supply or from ±1 V to ±18 V with dual supplies. Each comparator has a differential input arrangement, an open-collector output, and independent operation, allowing one section to monitor a positive threshold while the other monitors a different signal. Because the outputs are open collector, a pull-up resistor is required when driving CMOS, MCU, or other high-impedance logic inputs.
Typical uses include battery threshold detection, industrial sensor interfaces, overvoltage and undervoltage monitoring, window comparators, and general control loops. The wide supply range supports both low-voltage embedded systems and higher-voltage industrial environments. The 8-TSSOP package also permits compact placement where the open-collector output can be used to drive a pull-up-connected indicator or interface.
Designers should account for the open-collector architecture by adding a pull-up resistor at each output and checking that the required sink current stays within the device limits. Input common-mode range, supply voltage, output pull-up voltage, and response timing must also be reviewed against the intended system. For replacement decisions, verify the exact suffix and package because A, B, and V grades differ in qualification and specific performance limits.
This product page combines manufacturer specifications, package details, application guidance, and verified drop-in alternatives to support component selection and board-level replacement planning. Texas Instruments also provides a dedicated LM2903 product page and manufacturer part-details listing for lifecycle, documentation, and ordering review.
کے لیے ڈراپ اِن متبادل LM2903AVQPWRG4 — یکساں پیکیج، پن سے پن مطابقت پذیر۔ مختلف پیکیج والے پرزے جن کے لیے PCB دوبارہ کام درکار ہو، شامل نہیں ہیں۔
اس سیریز میں مختلف ورژن
اسی سیریز کے ماڈلز جو ڈراپ اِن مطابقت رکھتے ہیں LM2903AVQPWRG4 (یکساں فارم فیکٹر اور فٹ پرنٹ) — میں مختلف Comparator Type, Number of Channels, Output Type, Package, Maximum Supply Voltage.
LM2903AVQPWR
✅ ڈراپ-اِنقیمت کے لیے رابطہ کریں
ڈیٹا شیٹ دیکھیں →LM2903BVPWR
✅ ڈراپ-اِن ⚠️ تفصیلات غیر تصدیق شدہ📋 حوالہ جاتی متبادل (کیٹلاگ میں نہیں)
LM2903AVQPWRG4Q1
✅ ڈراپ-اِنقیمت کے لیے رابطہ کریں
ڈیٹا شیٹ دیکھیں →LM2903BVPWRG4
✅ ڈراپ-اِن ⚠️ تفصیلات غیر تصدیق شدہ📋 حوالہ جاتی متبادل (کیٹلاگ میں نہیں)
LM2903AVPWRG4
✅ ڈراپ-اِن ⚠️ تفصیلات غیر تصدیق شدہ📋 حوالہ جاتی متبادل (کیٹلاگ میں نہیں)
LM2903AVQPWRG4 زیادہ سے زیادہ ریٹنگز اور برقی خصوصیات
| Comparator Type | Dual differential comparator |
| Number of Channels | 2 channels |
| Supply Voltage Range, Single Supply | 2 V to 36 V |
| Supply Voltage Range, Dual Supply | ±1 V to ±18 V |
| آؤٹ پٹ کی قسم | Open-collector, rail-to-rail |
| Maximum Supply Voltage | 38 V |
| Input Offset Voltage, B-Version | 0.37 mV |
| Input Bias Current, B-Version | 3.5 nA |
| Supply Current per Comparator, B-Version | 200 µA |
| Response Time, B-Version | 1 µs |
| Input Bias Current at 5 V | 0.25 µA |
| Supply Drain Current per Comparator, V-Suffix Device | 0.4 mA typical |
| Tested Maximum Supply Voltage | 32 V for V-suffix devices |
| ESD Rating, HBM | 2 kV |
| پیکیج | 8-pin TSSOP (PW) |
| ماؤنٹنگ ٹائپ | Surface mount |
LM2903AVQPWRG4 پن کنفیگریشن
| پن 1 | OUT1 — Comparator 1 open-collector output |
| پن 2 | IN1- — Comparator 1 inverting input |
| پن 3 | IN1+ — Comparator 1 non-inverting input |
| پن 4 | GND — Ground reference |
| پن 5 | IN2+ — Comparator 2 non-inverting input |
| پن 6 | IN2- — Comparator 2 inverting input |
| پن 7 | OUT2 — Comparator 2 open-collector output |
| پن 8 | VCC — Positive supply voltage |
عام استعمالات
LM2903AVQPWRG4 کے لیے موزوں ہے 6 ایپلیکیشنs: Industrial Overvoltage and Undervoltage Monitoring, Battery Voltage Threshold Detection, Window Comparator for Sensor Signals, Relay and Solenoid Interface, Embedded System Logic Interfacing, Power Supply Rail Qualification.
Industrial Overvoltage and Undervoltage Monitoring
The LM2903AVQPWRG4 fits dual-rail supervision because its two independent differential comparators can monitor upper and lower voltage thresholds in one 8-TSSOP package. The single-supply operating range extends from 2 V to 36 V, while the 0.37 mV B-version input offset and 3.5 nA input bias current support accurate decisions near the threshold. Each open-collector output can pull down a fault signal or indicator line through an external pull-up resistor. Designers should set the divider values around the required thresholds and confirm that the monitored signal remains inside the input common-mode range.
تجویز کردہ
Battery Voltage Threshold Detection
The LM2903AVQPWRG4 can detect low and high battery thresholds with its two independent comparator channels. Its low 200 µA supply current per comparator in the B-version family reduces the impact on battery-powered systems, while 1 µs response time provides rapid switching after a threshold crossing. The open-collector outputs are useful for driving a pull-up-connected status LED, digital input, or power-control stage. The application must keep the battery voltage within the comparator supply and common-mode limits and account for the current drawn by the pull-up resistors.
تجویز کردہ
Window Comparator for Sensor Signals
The two channels in the LM2903AVQPWRG4 can establish lower and upper limits for a sensor signal, creating a window-comparison function without a separate comparator for each boundary. The 0.37 mV B-version input offset and 3.5 nA input bias current are particularly useful when the signal source has high source impedance or the valid operating band is narrow. Open-collector outputs permit wired-AND behavior when one pull-up serves both channels. For reliable operation, the sensor reference network must be low-noise, the input voltages must stay within the common-mode range, and the output transitions must meet downstream timing requirements.
تجویز کردہ
Relay and Solenoid Interface
The LM2903AVQPWRG4 can compare a control-voltage threshold and sink current into a relay or solenoid driver stage through its open-collector output. The wide 2 V to 36 V single-supply range provides flexibility in industrial control systems, and the two independent channels can supervise separate control conditions. Because the comparator itself is intended for logic-level sinking rather than direct high-current relay drive, use an appropriate transistor or driver stage and account for relay coil flyback protection. Set pull-up resistance so the output rise time remains compatible with the driver input.
تجویز کردہ
Embedded System Logic Interfacing
The LM2903AVQPWRG4 is suitable for interfacing an analog threshold signal to an MCU or other digital logic because its open-collector output can be pulled up to the digital system voltage. This decouples the output-high voltage from the comparator supply while retaining a simple, low-component interface. The 1 µs response time of the B-version family supports prompt state changes, and the 8-TSSOP package saves board area. The pull-up network should be placed near the receiving logic input, while the comparator input network should minimize noise pickup around the threshold node.
تجویز کردہ
Power Supply Rail Qualification
Two LM2903AVQPWRG4 comparator channels can monitor a power rail and a reference signal to qualify whether the rail is operating in its permitted band. The device’s 2 V minimum single-supply operation, 36 V maximum operating range, and 38 V maximum rating support a broad range of low- and higher-voltage systems. Open-collector outputs provide straightforward fault signaling through pull-up resistors. The comparison references should be stable, input currents should avoid shifting the reference node, and the chosen rail must remain within both the supply and input common-mode specifications during start-up and fault conditions.
تجویز کردہ
تجویز کردہ پروڈکٹس کا خلاصہ
کے لیے انجینئرنگ ریفرنس ڈیٹا LM2903AVQPWRG4 — موازنہ، ڈیزائن رہنمائی، اور تعمیل کی معلومات۔
انتخاب کی گائیڈ
متبادلات کے ساتھ موازنہ
| پیرامیٹر | یہ پروڈکٹ | LM2903AVQPWR | LM2903BVPWR | LM2903AVQPWRG4Q1 | LM2903BVPWRG4 | LM2903AVPWRG4 |
|---|---|---|---|---|---|---|
| Package | 8-TSSOP (PW) | 8-TSSOP (PW) | 8-TSSOP (PW) | 8-TSSOP (PW) | 8-TSSOP (PW) | 8-TSSOP (PW) |
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Comparator Configuration | Dual differential comparator | Dual differential comparator | Dual differential comparator | Dual differential comparator | Dual differential comparator | Dual differential comparator |
| Output Type | Open-collector, rail-to-rail | Open-collector, rail-to-rail | Open-collector, rail-to-rail | Open-collector, rail-to-rail | Open-collector, rail-to-rail | Open-collector, rail-to-rail |
| Single-Supply Operating Range | 2 V to 36 V | 2 V to 36 V | 2 V to 36 V | 2 V to 36 V | 2 V to 36 V | 2 V to 36 V |
| Maximum Supply Rating | 38 V | 38 V | 38 V | 38 V | 38 V | 38 V |
اہم امتیازی خصوصیات
- Dual independent comparator channels in one compact package (بمقابلہLM2903AVQPWR)
- Improved B-version input and response performance (بمقابلہLM2903AVQPWR)
- Automotive-qualified sourcing path in the same family (بمقابلہLM2903AVQPWRG4)
ڈیزائن نوٹس
Do not treat the open-collector output as a push-pull logic output. Each output requires a pull-up resistor because the device can sink the logic-low current but cannot actively source the logic-high current. Select the pull-up voltage for the receiving circuit, calculate the resistor against the permitted sink current, and verify that the resulting output rise time satisfies the downstream timing requirement.
Keep the reference divider, threshold node, and comparator input traces away from switching nodes and high-current return paths. Place the input network close to the relevant pins and route the two channels to minimize differential pickup, since an offset as low as 0.37 mV can be corrupted by nearby switching energy. Provide a direct ground return and maintain a short, low-impedance path from the device ground pin to the circuit reference.
Confirm the maximum supply voltage for the complete operating environment, including transients and inductive coupling. The LM2903 family has a 38 V maximum rating and supports operation from 2 V to 36 V on a single supply, but rating headroom does not eliminate the need for supply-noise control. Add filtering or clamping appropriate to the source while ensuring that the comparator input and output absolute maximum ratings are not exceeded.
When both comparator outputs feed the same pull-up node for wired-AND behavior, verify that one output can sink the combined current without violating its output limits. Also check whether the shared node introduces a slower rising edge than the receiving circuit permits. Separate pull-ups are preferable when independent rise times or independently scaled output currents are required.
تعمیل کی معلومات
The exact compliance declarations are not stated in the manufacturer material cited on this page. AEC-Q100 is not marked as not_applicable only because this is a general-purpose comparator; qualification must be checked for any automotive-grade alternative.