Texas Instruments

LM2903AVQPWRG4 - Dual Comparator | Texas Instruments

Teilenummer: LM2903AVQPWRG4 ✓ Aktiv
2 V to 36 V Vdss 3.5 nA Id 8-pin TSSOP (PW) Package
MOQ: 1 |

LM2903AVQPWRG4 Übersicht

The Texas Instruments LM2903AVQPWRG4 is a dual differential comparator with two independent open-collector, rail-to-rail outputs, a 2 V to 36 V single-supply operating range, and an 8-pin TSSOP package. Each comparator provides precise voltage comparison with an input offset voltage as low as 0.37 mV and an input bias current of 3.5 nA for the B-version family. The LM2903 family is designed for low-power voltage-detection and threshold-monitoring circuits.

A differential comparator is an analog integrated circuit that compares two input voltages and changes its output state when the difference between those voltages crosses a defined threshold. Within the comparator hierarchy, this device belongs to the general-purpose comparator, analog IC, and semiconductor categories. Its open-collector outputs allow the output stage to sink current while remaining compatible with external pull-up resistors, making it useful for wired logic, relay drivers, and level translation.

The LM2903B family offers low input offset voltage of 0.37 mV, low input bias current of 3.5 nA, supply current of 200 µA per comparator, and a faster response time of 1 µs. The B version is identified by Texas Instruments as a drop-in replacement for LM293, LM393, and LM2903 devices in both A and V grades. It also provides an extended temperature range and an HBM ESD rating of 2 kV.

The device supports operation from 2 V to 36 V with a single supply or from ±1 V to ±18 V with dual supplies. Each comparator has a differential input arrangement, an open-collector output, and independent operation, allowing one section to monitor a positive threshold while the other monitors a different signal. Because the outputs are open collector, a pull-up resistor is required when driving CMOS, MCU, or other high-impedance logic inputs.

Typical uses include battery threshold detection, industrial sensor interfaces, overvoltage and undervoltage monitoring, window comparators, and general control loops. The wide supply range supports both low-voltage embedded systems and higher-voltage industrial environments. The 8-TSSOP package also permits compact placement where the open-collector output can be used to drive a pull-up-connected indicator or interface.

Designers should account for the open-collector architecture by adding a pull-up resistor at each output and checking that the required sink current stays within the device limits. Input common-mode range, supply voltage, output pull-up voltage, and response timing must also be reviewed against the intended system. For replacement decisions, verify the exact suffix and package because A, B, and V grades differ in qualification and specific performance limits.

This product page combines manufacturer specifications, package details, application guidance, and verified drop-in alternatives to support component selection and board-level replacement planning. Texas Instruments also provides a dedicated LM2903 product page and manufacturer part-details listing for lifecycle, documentation, and ordering review.

Drop-in-Alternativen für LM2903AVQPWRG4 – gleiches Gehäuse, Pin-kompatibel. Bauteile mit anderem Gehäuse, die eine PCB-Überarbeitung erfordern, sind ausgeschlossen.

Varianten dieser Serie

Modelle derselben Serie, die drop-in-kompatibel sind mit LM2903AVQPWRG4 (gleiche Bauform und Footprint) – abweichend in Comparator Type, Number of Channels, Output Type, Package, Maximum Supply Voltage.

Texas Instruments
Comparator Type: Dual differential voltage comparator
Number of Channels: 2
Output Type: Open-collector
Vergleichen mit LM2903AVQPWRG4 →
Texas Instruments
Output Type: Open-collector
Package: 8-pin TSSOP
Maximum Supply Voltage: 36 V
Vergleichen mit LM2903AVQPWRG4 →

LM2903AVQPWR

✅ Drop-In
Texas Instruments
📦 8-TSSOP (PW)
Dual differential voltage comparator · 2 · Single supply or dual supplies · 30 V for V-suffix devices; 32 V for non-V devices · 0.4 mA typical per comparator · Open-collector · Differential input

Preis auf Anfrage

Datenblatt ansehen →

LM2903BVPWR

✅ Drop-In ⚠️ Spezifikationen ungeprüft
📦 8-TSSOP (PW)
B-version response time is 1 µs versus the original family’s specification, while supply and pin configuration remain compatible

📋 Referenzalternative (nicht im Katalog)

LM2903AVQPWRG4Q1

✅ Drop-In
Texas Instruments
📦 8-TSSOP (PW)
Dual differential comparator · 2 channels · Open-collector · 2 V to 36 V · ±1 V to ±18 V · 36 V · 1.3 µs · 0.4 mA typical

Preis auf Anfrage

Datenblatt ansehen →

LM2903BVPWRG4

✅ Drop-In ⚠️ Spezifikationen ungeprüft
📦 8-TSSOP (PW)
B-version family provides 0.37 mV input offset and 1 µs response time; exact orderable suffix requires manufacturer confirmation

📋 Referenzalternative (nicht im Katalog)

LM2903AVPWRG4

✅ Drop-In ⚠️ Spezifikationen ungeprüft
📦 8-TSSOP (PW)
Same LM2903AV device family and TSSOP footprint, with the standard rather than V temperature-grade designation; core electrical ratings are equivalent

📋 Referenzalternative (nicht im Katalog)

LM2903AVQPWRG4 Grenzwerte & elektrische Eigenschaften

Comparator Type Dual differential comparator
Number of Channels 2 channels
Supply Voltage Range, Single Supply 2 V to 36 V
Supply Voltage Range, Dual Supply ±1 V to ±18 V
Ausgangstyp Open-collector, rail-to-rail
Maximum Supply Voltage 38 V
Input Offset Voltage, B-Version 0.37 mV
Input Bias Current, B-Version 3.5 nA
Supply Current per Comparator, B-Version 200 µA
Response Time, B-Version 1 µs
Input Bias Current at 5 V 0.25 µA
Supply Drain Current per Comparator, V-Suffix Device 0.4 mA typical
Tested Maximum Supply Voltage 32 V for V-suffix devices
ESD Rating, HBM 2 kV
Gehäuse 8-pin TSSOP (PW)
Montageart Surface mount

LM2903AVQPWRG4 Pin-Konfiguration

TSSOP-8 Package Pinout Diagram TSSOP-8 8-pin thin shrink small outline, P0.65mm, JEDEC MO-153. 1 8 2 7 3 6 4 5 TSSOP-8
Pin 1 OUT1 — Comparator 1 open-collector output
Pin 2 IN1- — Comparator 1 inverting input
Pin 3 IN1+ — Comparator 1 non-inverting input
Pin 4 GND — Ground reference
Pin 5 IN2+ — Comparator 2 non-inverting input
Pin 6 IN2- — Comparator 2 inverting input
Pin 7 OUT2 — Comparator 2 open-collector output
Pin 8 VCC — Positive supply voltage

Typische Anwendungen

LM2903AVQPWRG4 ist geeignet für 6 Anwendungs: Industrial Overvoltage and Undervoltage Monitoring, Battery Voltage Threshold Detection, Window Comparator for Sensor Signals, Relay and Solenoid Interface, Embedded System Logic Interfacing, Power Supply Rail Qualification.

🏭

Industrial Overvoltage and Undervoltage Monitoring

The LM2903AVQPWRG4 fits dual-rail supervision because its two independent differential comparators can monitor upper and lower voltage thresholds in one 8-TSSOP package. The single-supply operating range extends from 2 V to 36 V, while the 0.37 mV B-version input offset and 3.5 nA input bias current support accurate decisions near the threshold. Each open-collector output can pull down a fault signal or indicator line through an external pull-up resistor. Designers should set the divider values around the required thresholds and confirm that the monitored signal remains inside the input common-mode range.

⚡

Battery Voltage Threshold Detection

The LM2903AVQPWRG4 can detect low and high battery thresholds with its two independent comparator channels. Its low 200 µA supply current per comparator in the B-version family reduces the impact on battery-powered systems, while 1 µs response time provides rapid switching after a threshold crossing. The open-collector outputs are useful for driving a pull-up-connected status LED, digital input, or power-control stage. The application must keep the battery voltage within the comparator supply and common-mode limits and account for the current drawn by the pull-up resistors.

🧩

Window Comparator for Sensor Signals

The two channels in the LM2903AVQPWRG4 can establish lower and upper limits for a sensor signal, creating a window-comparison function without a separate comparator for each boundary. The 0.37 mV B-version input offset and 3.5 nA input bias current are particularly useful when the signal source has high source impedance or the valid operating band is narrow. Open-collector outputs permit wired-AND behavior when one pull-up serves both channels. For reliable operation, the sensor reference network must be low-noise, the input voltages must stay within the common-mode range, and the output transitions must meet downstream timing requirements.

🔧

Relay and Solenoid Interface

The LM2903AVQPWRG4 can compare a control-voltage threshold and sink current into a relay or solenoid driver stage through its open-collector output. The wide 2 V to 36 V single-supply range provides flexibility in industrial control systems, and the two independent channels can supervise separate control conditions. Because the comparator itself is intended for logic-level sinking rather than direct high-current relay drive, use an appropriate transistor or driver stage and account for relay coil flyback protection. Set pull-up resistance so the output rise time remains compatible with the driver input.

📱

Embedded System Logic Interfacing

The LM2903AVQPWRG4 is suitable for interfacing an analog threshold signal to an MCU or other digital logic because its open-collector output can be pulled up to the digital system voltage. This decouples the output-high voltage from the comparator supply while retaining a simple, low-component interface. The 1 µs response time of the B-version family supports prompt state changes, and the 8-TSSOP package saves board area. The pull-up network should be placed near the receiving logic input, while the comparator input network should minimize noise pickup around the threshold node.

🖥️

Power Supply Rail Qualification

Two LM2903AVQPWRG4 comparator channels can monitor a power rail and a reference signal to qualify whether the rail is operating in its permitted band. The device’s 2 V minimum single-supply operation, 36 V maximum operating range, and 38 V maximum rating support a broad range of low- and higher-voltage systems. Open-collector outputs provide straightforward fault signaling through pull-up resistors. The comparison references should be stable, input currents should avoid shifting the reference node, and the chosen rail must remain within both the supply and input common-mode specifications during start-up and fault conditions.

Zusammenfassung der empfohlenen Produkte

LM2903AVQPWR Texas Instruments Verwendet in: Industrial Overvoltage and Undervoltage Monitoring, Window Comparator for Sensor Signals, Embedded System Logic Interfacing LM2903BVPWR B-version comparator for improved input specifications Verwendet in: Industrial Overvoltage and Undervoltage Monitoring, Relay and Solenoid Interface, Power Supply Rail Qualification LM2903AVQPWRG4Q1 Texas Instruments Verwendet in: Battery Voltage Threshold Detection, Relay and Solenoid Interface LM2903BVPWRG4 B-version low-power comparator alternative Verwendet in: Battery Voltage Threshold Detection LM2903AVPWRG4 Standard temperature-grade dual comparator Verwendet in: Window Comparator for Sensor Signals, Embedded System Logic Interfacing LM2903AVQPWRG4 Texas Instruments Verwendet in: Power Supply Rail Qualification
What is the LM2903AVQPWRG4?
The LM2903AVQPWRG4 is a Texas Instruments dual differential comparator with two independent open-collector, rail-to-rail outputs in an 8-pin TSSOP package. According to the Texas Instruments LM2903 product page, it operates from 2 V to 36 V with a single supply or from ±1 V to ±18 V with dual supplies. The dual-section architecture allows two independent threshold or window comparisons within one package.
What are the key specifications of LM2903AVQPWRG4 that engineers should know?
The LM2903AVQPWRG4 combines a 2 V to 36 V single-supply range, open-collector rail-to-rail outputs, and two independent comparator channels in an 8-pin TSSOP package. Texas Instruments identifies the B-version family with 0.37 mV input offset voltage, 3.5 nA input bias current, 200 µA supply current per comparator, and a 1 µs response time. These figures make the family suitable for precision threshold detection, low-power sensing, and general-purpose control.
What is the operating voltage of LM2903AVQPWRG4?
The LM2903AVQPWRG4 operates from 2 V to 36 V using a single supply or from ±1 V to ±18 V using dual supplies. Texas Instruments lists a maximum rating of 38 V for the LM2903 family. Supply selection must also account for the input common-mode range and the voltage applied to each open-collector output through its external pull-up resistor.
Where can I download the LM2903AVQPWRG4 datasheet PDF?
The LM2903AVQPWRG4 datasheet is available through the Texas Instruments LM2903 part-details page at https://www.ti.com/product/LM2903/part-details/LM2903AVQPWRG4. Use the document resources on that page for the manufacturer PDF. The manufacturer document should be the primary reference for the 8-pin TSSOP pin configuration, electrical limits, input and output behavior, and ordering information.
Where can I find the LM2903AVQPWRG4 pinout?
The LM2903AVQPWRG4 pinout is shown in the Texas Instruments LM2903 manufacturer documentation for the 8-pin TSSOP (PW) package. The standard pin assignment uses pins 1 and 7 for the two open-collector outputs, pins 2 and 6 for inverting inputs, pins 3 and 5 for non-inverting inputs, pin 4 for ground, and pin 8 for the positive supply. Confirm this assignment against the manufacturer pin-description table before PCB assembly.
Does LM2903AVQPWRG4 need pull-up resistors?
Yes, the LM2903AVQPWRG4 needs an external pull-up resistor on each open-collector output for normal high-level operation. The transistor output actively pulls low but does not actively drive high, so the pull-up establishes the high voltage. Select the resistor to provide adequate rise time without exceeding the output sink-current rating, and verify the pull-up voltage remains within the applicable output limits.
What is the difference between LM2903 and LM2903B?
The LM2903B family offers improved performance over the original LM2903, including 0.37 mV input offset voltage, 3.5 nA input bias current, 200 µA supply current per comparator, and a 1 µs response time. Texas Instruments states that the B version is a drop-in replacement for LM293, LM393, and LM2903 devices in both A and V grades. Exact package, temperature, qualification, and ordering suffixes must still be matched.
What can replace LM2903AVQPWRG4?
The closest same-family replacements include LM2903AVQPWR, LM2903BVPWR, and LM2903AVQPWRG4Q1 when their package and qualification requirements match the original. Texas Instruments specifically identifies the LM2903B as a drop-in replacement for A- and V-grade LM2903 devices. Verify the pinout, supply limits, input common-mode range, temperature grade, and open-collector output requirements before approving any substitution.
Is LM2903AVQPWRG4 the same as LM2903AVQPWR?
The LM2903AVQPWRG4 and LM2903AVQPWR refer to closely related ordering configurations of the same LM2903AV family, but the G4 suffix identifies the specified reel or packing format. Both listings identify the 8-pin TSSOP device with open-collector, rail-to-rail outputs. Confirm the exact suffix, quantity per reel, and orderable status in the manufacturer part-details table before treating them as interchangeable procurement entries.
When should I choose LM2903AVQPWRG4 over an LM393 variant?
Choose the LM2903AVQPWRG4 when the design needs the LM2903 family’s single or dual supply flexibility, low-power operation, and open-collector outputs. Choose an LM393B variant only after confirming that its pinout, supply limits, common-mode range, temperature grade, and package satisfy the design. The manufacturer identifies the B-version LM2903 as a drop-in family option for LM393 A- and V-grade applications, but qualification and ordering suffixes still require review.
Can LM2903BVPWR replace LM2903AVQPWRG4?
LM2903BVPWR can serve as a candidate replacement when its 8-pin TSSOP pinout and operating limits meet the board requirements. Texas Instruments states that the B version is a drop-in replacement for LM293, LM393, and LM2903 A- and V grades, while the LM2903AVQPWRG4 is the V-grade, extended-temperature TSSOP configuration. Check automotive qualification, maximum rated voltage, and the exact orderable suffix before final substitution.
Is LM2903AVQPWRG4 suitable for industrial voltage monitoring?
The LM2903AVQPWRG4 is suitable for industrial voltage-monitoring designs that remain within its 2 V to 36 V single-supply range and require an open-collector interface. Its two independent comparators can implement separate overvoltage and undervoltage thresholds, while the extended-temperature designation supports wider operating conditions than the standard grade. Check the exact temperature limits, output pull-up arrangement, and isolation requirements of the completed circuit.
What is the best use for the LM2903AVQPWRG4 open-collector output?
The open-collector output is best used when a logic node needs a passive pull-up, an adjustable output voltage, or low-side sinking of a load such as a relay driver. Pull the output low with an external resistor connected to the desired logic supply, allowing the voltage source to be selected independently of the comparator supply. This architecture does not actively source current, so it is unsuitable where a directly driven high output is required without a pull-up.
How does LM2903AVQPWRG4 compare with LM2904 for dual-comparator designs?
The LM2903AVQPWRG4 provides two independent differential comparators with open-collector outputs, whereas LM2904 products are generally associated with open-drain or open-collector comparators using different package and suffix options. The choice must be based on exact pinout, input common-mode range, supply limits, and output ratings rather than the comparator function alone. Texas Instruments comparison resources and the manufacturer datasheets should be used to confirm interchangeability.
Where can I buy LM2903AVQPWRG4 and how is it priced?
Use the Request a Quote form on this page to request LM2903AVQPWRG4 pricing, stock confirmation, lead time, and order quantities from XAIPART. The component is listed for the 8-pin TSSOP package as a dual open-collector comparator. For a current commercial commitment, include the required quantity, target reel quantity, shipment destination, and expected production schedule in the quote request.
Is LM2903AVQPWRG4 in stock and what is its lead time?
Stock and lead time should be confirmed through the Request a Quote form on this page because availability can change with quantity, packing format, and manufacturing schedule. The manufacturer identifies LM2903AVQPWRG4 as an LM2903AV 8-pin TSSOP orderable part. Include the quantity per reel and target delivery date in the request so the supplier can provide the most relevant availability commitment.
What is the best Texas Instruments equivalent for LM2903AVQPWRG4?
The closest Texas Instruments alternatives depend on the required temperature grade and qualification. LM2903AVQPWR offers the closest ordering-family match without the G4 packing suffix, while LM2903BVPWR uses the improved B-version performance and LM2903AVQPWRG4Q1 addresses automotive-qualified sourcing. All candidates must retain the 8-pin TSSOP footprint, required pin functions, voltage ratings, and open-collector behavior before they qualify as drop-in replacements.

Technische Referenzdaten für LM2903AVQPWRG4 – Vergleich, Designhinweise und Compliance-Informationen.

Auswahlhilfe

Choose LM2903AVQPWRG4 when the board needs the LM2903AV grade in an 8-TSSOP package with two independent open-collector comparators and a wide single-supply operating range. LM2903AVQPWR is the closest procurement alternative when its packing format meets the production plan. Choose an LM2903B variant when the design benefits from 0.37 mV input offset, 3.5 nA input bias current, 200 µA supply current per comparator, and 1 µs response. Use LM2903AVQPWRG4Q1 for automotive qualification requirements. For every candidate, verify the pinout, temperature grade, common-mode range, supply rating, pull-up arrangement, and exact orderable suffix before PCB substitution.

Vergleich mit Alternativen

Parameter Dieses Produkt LM2903AVQPWR LM2903BVPWR LM2903AVQPWRG4Q1 LM2903BVPWRG4 LM2903AVPWRG4
Package 8-TSSOP (PW) 8-TSSOP (PW) 8-TSSOP (PW) 8-TSSOP (PW) 8-TSSOP (PW) 8-TSSOP (PW)
Brand Texas Instruments Texas Instruments Texas Instruments Texas Instruments Texas Instruments Texas Instruments
Comparator Configuration Dual differential comparator Dual differential comparator Dual differential comparator Dual differential comparator Dual differential comparator Dual differential comparator
Output Type Open-collector, rail-to-rail Open-collector, rail-to-rail Open-collector, rail-to-rail Open-collector, rail-to-rail Open-collector, rail-to-rail Open-collector, rail-to-rail
Single-Supply Operating Range 2 V to 36 V 2 V to 36 V 2 V to 36 V 2 V to 36 V 2 V to 36 V 2 V to 36 V
Maximum Supply Rating 38 V 38 V 38 V 38 V 38 V 38 V

Wichtigste Unterscheidungsmerkmale

  • Dual independent comparator channels in one compact package (vs. LM2903AVQPWR)
  • Improved B-version input and response performance (vs. LM2903AVQPWR)
  • Automotive-qualified sourcing path in the same family (vs. LM2903AVQPWRG4)

Designhinweise

Do not treat the open-collector output as a push-pull logic output. Each output requires a pull-up resistor because the device can sink the logic-low current but cannot actively source the logic-high current. Select the pull-up voltage for the receiving circuit, calculate the resistor against the permitted sink current, and verify that the resulting output rise time satisfies the downstream timing requirement.

Keep the reference divider, threshold node, and comparator input traces away from switching nodes and high-current return paths. Place the input network close to the relevant pins and route the two channels to minimize differential pickup, since an offset as low as 0.37 mV can be corrupted by nearby switching energy. Provide a direct ground return and maintain a short, low-impedance path from the device ground pin to the circuit reference.

Confirm the maximum supply voltage for the complete operating environment, including transients and inductive coupling. The LM2903 family has a 38 V maximum rating and supports operation from 2 V to 36 V on a single supply, but rating headroom does not eliminate the need for supply-noise control. Add filtering or clamping appropriate to the source while ensuring that the comparator input and output absolute maximum ratings are not exceeded.

When both comparator outputs feed the same pull-up node for wired-AND behavior, verify that one output can sink the combined current without violating its output limits. Also check whether the shared node introduces a slower rising edge than the receiving circuit permits. Separate pull-ups are preferable when independent rise times or independently scaled output currents are required.

Compliance-Informationen

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
Bleifrei
Unknown
Halogenfrei
Unknown
Konfliktmineralien
Unknown

The exact compliance declarations are not stated in the manufacturer material cited on this page. AEC-Q100 is not marked as not_applicable only because this is a general-purpose comparator; qualification must be checked for any automotive-grade alternative.

Daten verifiziert am: 2026-11-09 – Daten geprüft und kuratiert vom Bauteil-Engineering-Team von XAIPART

Ähnliche Suchanfragen

LM2903AVQPWRG4 datasheet LM2903AVQPWRG4 datasheet pdf LM2903AVQPWRG4 pinout LM2903AVQPWRG8-TSSOP comparator LM2903AVQPWRG4 open collector LM2903AVQPWRG4 supply voltage LM2903AVQPWRG4 response time LM2903AVQPWRG4 equivalent LM2903AVQPWRG4 replacement LM2903AVQPWRG4 cross reference LM2903AVQPWRG4 vs LM2903BVPWR LM2903AVQPWRG4 footprint LM2903AVQPWRG4 price LM2903AVQPWRG4 stock Texas Instruments LM2903AVQPWRG4

Verwandte Bauteile & Begriffe

Texas Instruments LM2903AVQPWRG4 LM2903AVQPWR LM2903BVPWR LM2903AVQPWRG4Q1 LM2903BVPWRG4 LM2903AVPWRG4 dual differential comparator general-purpose comparator analog comparator analog integrated circuit semiconductor open-collector output rail-to-rail output input offset voltage input bias current supply current response time 8-TSSOP PW package surface-mount package threshold detection overvoltage monitoring undervoltage monitoring RoHS REACH
Schnellangebot-RFQ
Geben Sie alle Details an – unser Vertriebsteam antwortet innerhalb von 24 Stunden
Teilenummer Hersteller Gehäuse QTY Zielpreis Gesamt
✓
Angebotsanfrage gesendet!

Wir antworten innerhalb von 24 Stunden auf Ihre E-Mail

1
RFQ gesendet
2
Angebot erhalten
3
Bestellung aufgegeben
4
Zahlung
5
Versandt
6
Geliefert
RFQ-Details ansehen