LM324DTBG - Quad 3-32V Op Amp | onsemi | TSSOP-14
MPN: LM324DTBG ✓ فعالLM324DTBG جائزہ
A quad operational amplifier combines four independent amplifier sections in one package. An operational amplifier is a voltage-feedback amplifier whose differential input is amplified by a high open-loop gain. The LM324 belongs to the broader hierarchy of analog signal-chain ICs, amplifier ICs, and general-purpose operational amplifiers. Four sections in one package reduce board area and can simplify designs requiring several low-frequency signal stages.
The LM324DTBG provides four amplifier circuits, a 1 MHz gain-bandwidth product, and a 0.6 V/µs slew rate. These characteristics suit audio-frequency control loops, sensor conditioning, low-frequency active filters, and general-purpose voltage amplification. The 3 V to 32 V supply range also supports single-supply operation from conventional 5 V and 24 V industrial rails, subject to the device's detailed operating limits.
The LM324 series uses true differential inputs, which is important when each amplifier receives two independently changing input voltages. A 5 mV input offset voltage characterizes the practical dc error around the signal path. The 1 MHz gain-bandwidth product limits the frequency range over which closed-loop gain can remain stable, while the 0.6 V/µs slew rate governs large-signal response. These are general-purpose figures rather than high-speed or precision-amplifier ratings.
Typical applications include four-channel sensor buffering, industrial control interfaces, low-frequency active filters, audio preamplifier stages, and general instrumentation. The same quad package can also implement four independent amplifier functions, such as comparator-style signal conditioning, differential-to-single-ended conversion, or distributed gain stages. Because the device is not specified as a rail-to-rail amplifier, input and output common-mode limits must be respected in each design.
For stable operation, follow the manufacturer datasheet when selecting input and output compensation components, grounding the unused amplifier sections, and setting gain through appropriate feedback networks. Keep sensitive input traces short, place bypass capacitance close to the supply pins, and verify common-mode and output-swing limits against the actual signal range. The TSSOP-14 footprint also requires adequate copper area and assembly-process clearance.
This product page combines the LM324DTBG electrical identity, package information, sourcing structure, comparison criteria, and practical design guidance. It helps engineers evaluate whether this 3 V to 32 V, 1 MHz quad operational amplifier is appropriate for a new design or an existing 14-TSSOP circuit before beginning detailed circuit simulation and qualification.
کے لیے ڈراپ اِن متبادل LM324DTBG — یکساں پیکیج، پن سے پن مطابقت پذیر۔ مختلف پیکیج والے پرزے جن کے لیے PCB دوبارہ کام درکار ہو، شامل نہیں ہیں۔
اس سیریز میں مختلف ورژن
اسی سیریز کے ماڈلز جو ڈراپ اِن مطابقت رکھتے ہیں LM324DTBG (یکساں فارم فیکٹر اور فٹ پرنٹ) — میں مختلف Number of Amplifiers, Package, Packaging, Temperature Grade.
LM324DTBR2G
✅ ڈراپ-اِنقیمت کے لیے رابطہ کریں
ڈیٹا شیٹ دیکھیں →LM324DTBG زیادہ سے زیادہ ریٹنگز اور برقی خصوصیات
| Amplifier Type | General Purpose |
| Number of Amplifiers | 4 circuits |
| Supply Voltage Range | 3 V to 32 V |
| Gain-Bandwidth Product | 1 MHz |
| Slew Rate | 0.6 V/µs |
| Input Offset Voltage | 5 mV |
| Input Type | True differential inputs |
| پیکیج | 14-TSSOP, 0.173 inch / 4.40 mm width |
| ماؤنٹنگ ٹائپ | Surface mount |
| Packaging | Tube |
| Temperature Grade | Commercial |
LM324DTBG 14-tssop, 0.173 inch / 4.40 mm width پن کنفیگریشن گائیڈ
LM324DTBG (14-tssop, 0.173 inch / 4.40 mm width پیکیج) کے لیے پن کنفیگریشن۔ اس اینالاگ کمپوننٹ میں اِن پٹ، آؤٹ پٹ اور پاور سپلائی پنز شامل ہیں۔ آفسیٹ نل، کمپنسیشن اور اِن ایبل پن کنفیگریشنز کے لیے مینوفیکچرر کے ڈیٹا شیٹ سے رجوع کریں۔ سگنل کنڈیشننگ اور ایمپلیفائر سرکٹس کے لیے مثالی۔
کے لیے تفصیلی پن آؤٹ ڈیٹا دستیاب نہیں LM324DTBG.
رجوع کریں ڈیٹا شیٹ مکمل پن کنفیگریشن کے لیے۔
عام استعمالات
LM324DTBG کے لیے موزوں ہے 6 ایپلیکیشنs: Industrial Sensor Signal Conditioning, Low-Frequency Active Filtering, Audio Preamplifier Stages, General-Purpose Instrumentation Buffering, Control-System Interface Circuits, Portable Battery-Powered Analog Front End.
Industrial Sensor Signal Conditioning
The LM324DTBG fits four-channel industrial sensor conditioning because it combines four true differential-input amplifiers, a 3 V to 32 V supply range, and a 1 MHz gain-bandwidth product in one 14-TSSOP package. Each section can buffer a transducer output before conversion or control circuitry, reducing board space while preserving a common amplifier topology. The 0.6 V/µs slew rate is adequate for many low-frequency sensors, while the 5 mV input offset rating must be weighed against measurement accuracy. Keep input traces short, reference the unused sections according to the datasheet, and confirm common-mode headroom before accepting sensor signals near either supply rail.
تجویز کردہ
Low-Frequency Active Filtering
Each section of the LM324DTBG can implement a low-frequency active filter stage with a 1 MHz gain-bandwidth product and 0.6 V/µs slew rate. Four independent amplifiers allow a compact fourth-order or multi-band filter without requiring four separate packages, provided the closed-loop gain and stability requirements are satisfied. A 24 V industrial rail falls within the LM324DTBG's 3 V to 32 V operating range, although the signal must remain inside the amplifier's common-mode and output-swing limits. Use the manufacturer's recommended compensation for non-inverting and inverting topologies, and validate gain, phase margin, and output amplitude in simulation before fabrication.
تجویز کردہ
Audio Preamplifier Stages
The LM324DTBG can provide low-frequency audio preamplification where four buffered signal paths are needed. Its 0.6 V/µs slew rate supports ordinary audio-band signals, and the 1 MHz gain-bandwidth product allows useful closed-loop gain at frequencies well above the audio band. The device is a general-purpose rather than low-noise audio amplifier, so input-referred noise and distortion should be checked against the system requirement. It is more appropriate for microphone preamplifier, line-level buffering, and headphone-driver support stages than for a demanding high-fidelity audio signal chain. Confirm output swing into the selected load and avoid relying on rail-to-rail behavior at low supply voltages.
تجویز کردہ
General-Purpose Instrumentation Buffering
The LM324DTBG is appropriate for instrumentation buffering when four measurement channels can share a general-purpose amplifier architecture. True differential inputs allow each amplifier to respond to the difference between two sensor or source nodes, while the 3 V to 32 V range supports both low-voltage and industrial supply environments. Its 5 mV input offset voltage is the primary accuracy consideration for precision measurements, so applications requiring tighter calibration should use a precision quad amplifier instead. Route high-impedance sources with short traces, guard sensitive inputs against leakage, and check bias-current effects using the detailed electrical characteristics in the onsemi LM324 datasheet.
تجویز کردہ
Control-System Interface Circuits
The four amplifiers in the LM324DTBG can implement interface, error, drive, and signal-conditioning functions for a compact control system. A 3 V to 32 V supply range allows operation from a 5 V logic-oriented rail or a 24 V industrial bus-derived supply, provided regulation and transient requirements are met upstream. The 1 MHz bandwidth is suitable for many slow control loops, while the 0.6 V/µs slew rate determines how quickly the outputs can follow larger excursions. Common-mode range and output swing must be checked against sensor and actuator levels. A 14-TSSOP footprint saves board area, but thermal dissipation and assembly clearance remain important at sustained output loads.
تجویز کردہ
Portable Battery-Powered Analog Front End
The LM324DTBG can serve as a battery-powered analog front end when the design operates within its 3 V to 32 V supply range and accepts general-purpose accuracy. Four amplifier sections allow signal conditioning, gain, filtering, and output buffering in a compact surface-mount footprint. The 5 mV input offset rating should be compared with the smallest signal that must be resolved, while the 0.6 V/µs slew rate should be checked against the required waveform rise time. Low supply voltage also reduces available output swing and common-mode range, making bias-point analysis essential. Battery operation additionally requires attention to device quiescent current, leakage into high-impedance sources, and the resulting power budget.
تجویز کردہ
تجویز کردہ پروڈکٹس کا خلاصہ
کے لیے انجینئرنگ ریفرنس ڈیٹا LM324DTBG — موازنہ، ڈیزائن رہنمائی، اور تعمیل کی معلومات۔
انتخاب کی گائیڈ
متبادلات کے ساتھ موازنہ
| پیرامیٹر | یہ پروڈکٹ | LM324DTBR2G |
|---|---|---|
| Package | 14-TSSOP | 14-TSSOP |
| Brand | onsemi | onsemi |
| Amplifier Configuration | Quad | Quad |
| Number of Circuits | 4 circuits | 4 circuits |
| Amplifier Type | General Purpose | General Purpose |
| Gain-Bandwidth Product | 1 MHz | 1 MHz |
اہم امتیازی خصوصیات
- Four general-purpose amplifiers are integrated into one 14-TSSOP package (بمقابلہLM324DTBR2G)
- Wide supply operating range supports low-voltage and industrial rails (بمقابلہLM324DTBR2G)
- Slew rate is specified for practical low-frequency signal movement (بمقابلہLM324DTBR2G)
- True differential inputs support direct difference-signal conditioning (بمقابلہLM324DTBR2G)
ڈیزائن نوٹس
Do not assume that a quad operational amplifier can process signals at the full supply range. Before assigning the LM324DTBG to a sensor or control interface, compare the signal excursion with the input common-mode range and compare the required load current with the output-current and swing limits. The 5 mV input offset voltage also means that a small sensor signal may require a more accurate amplifier. Use the manufacturer datasheet for the exact bias-point and output-swing limits.
Place bypass capacitors close to the supply and ground pins, use a low-impedance ground plane, and keep each amplifier's feedback and compensation components close to its TSSOP pins. Treat the four amplifier sections independently: route the input and output of each section directly to its intended pins, and configure unused sections according to the onsemi recommendations. This prevents high-current output loops and switching-node paths from coupling into sensitive amplifier inputs.
Estimated: device power dissipation equals the average supply voltage multiplied by total supply current under the intended operating condition. These operating values are not specified here, so no fixed dissipation or junction-temperature result can be assigned. Calculate the loss for both idle and maximum-load states, then use the onsemi thermal information together with the actual TSSOP copper area to determine whether additional thermal spreading is required.
The 1 MHz gain-bandwidth product and 0.6 V/µs slew rate set the useful frequency and large-signal boundaries of the LM324DTBG. Avoid asking the device to deliver closed-loop gain or output amplitude beyond those limits, because the result can be gain compression, slew-rate distortion, or reduced stability margin. Simulate the complete feedback network with realistic loading, and include output-capacitance and parasitic effects when the amplifier drives cables or sampling stages.
تعمیل کی معلومات
The LM324 family appears in comparisons that mention RoHS and REACH, but an explicit status for this exact onsemi ordering code was not identified. AEC-Q100, lead-free, halogen-free, and conflict-minerals status therefore remain unknown.