LM358APT - Dual Low-Power Op Amp in 8-TSSOP | STMicroelectronics
MPN: LM358APT ✓ فعالLM358APT جائزہ
An operational amplifier is an analog building block that amplifies the difference between two input voltages. The LM358 combines two such amplifier channels in one compact package, reducing component count and simplifying PCB routing. In a dual amplifier, one channel can perform signal conditioning while the other provides feedback, filtering, or an independent control function. Its low-power biasing makes it appropriate for battery-operated and embedded systems where each active circuit consumes power continuously.
The principal benefits of the LM358APT are integration, low power consumption, and flexible single- or dual-supply operation. Two amplifiers in one package conserve board area and can reduce the number of external ICs required for comparison, conditioning, and current-feedback applications. Because both channels share the same supply pins, the circuit designer can also establish common rail and ground references throughout the analog section of the board.
The LM358 architecture is widely used in general-purpose analog designs because each channel provides high open-loop voltage gain, differential input capability, and internal frequency compensation. These characteristics simplify closed-loop amplifier design without requiring an external compensation network. Engineers commonly use the device around sensor interfaces, transducers, audio preamplifier stages, and slow closed-loop control loops.
Typical uses include conditioning a bridge or resistive sensor, buffering an analog-to-digital converter input, amplifying instrumentation signals, implementing window comparators, and driving the input stage of a power-control circuit. Its internal compensation and dual-channel organization are particularly useful in compact embedded products where each additional package increases board cost and routing complexity.
PCB layout should keep input and feedback traces short, place input-biasing resistors close to the relevant pins, and route the ground connection directly to the package ground pin. Decoupling capacitors should be connected with minimal trace length. Because an operational amplifier can respond to unintended feedback caused by parasitic capacitance, clean layout is often more important than adding large external capacitors to compensate for poor routing.
This page combines the LM358APT catalog identity, package information, cross-reference options, and practical PCB guidance. It also organizes pin-level information, application guidance, and design cautions so engineers can evaluate the part quickly before starting a board layout or prototype build.
کے لیے ڈراپ اِن متبادل LM358APT — یکساں پیکیج، پن سے پن مطابقت پذیر۔ مختلف پیکیج والے پرزے جن کے لیے PCB دوبارہ کام درکار ہو، شامل نہیں ہیں۔
اس سیریز میں مختلف ورژن
اسی سیریز کے ماڈلز جو ڈراپ اِن مطابقت رکھتے ہیں LM358APT (یکساں فارم فیکٹر اور فٹ پرنٹ) — میں مختلف Amplifier Type, Package.
OPA2192IP
✅ ڈراپ-اِن📋 حوالہ جاتی متبادل (کیٹلاگ میں نہیں)
OPA277UA
✅ ڈراپ-اِنقیمت کے لیے رابطہ کریں
ڈیٹا شیٹ دیکھیں →TLV9002IPWR
✅ ڈراپ-اِن📋 حوالہ جاتی متبادل (کیٹلاگ میں نہیں)
MCP6001-I/SS
✅ ڈراپ-اِن📋 حوالہ جاتی متبادل (کیٹلاگ میں نہیں)
TLV2462IPWR
✅ ڈراپ-اِن📋 حوالہ جاتی متبادل (کیٹلاگ میں نہیں)
RC4558PZ
✅ ڈراپ-اِن📋 حوالہ جاتی متبادل (کیٹلاگ میں نہیں)
LM358APT زیادہ سے زیادہ ریٹنگز اور برقی خصوصیات
| Amplifier Type | Standard general-purpose operational amplifier |
| Number of Amplifier Channels | 2 channels |
| Number of Circuits | 2 circuits |
| پیکیج | 8-TSSOP |
| ماؤنٹنگ ٹائپ | Surface mount |
LM358APT پن کنفیگریشن
| پن 1 | OUT A — Amplifier A output |
| پن 2 | IN A- — Amplifier A inverting input |
| پن 3 | IN A+ — Amplifier A non-inverting input |
| پن 4 | V- — Negative supply connection |
| پن 5 | IN B+ — Amplifier B non-inverting input |
| پن 6 | IN B- — Amplifier B inverting input |
| پن 7 | OUT B — Amplifier B output |
| پن 8 | V+ — Positive supply connection |
عام استعمالات
LM358APT کے لیے موزوں ہے 6 ایپلیکیشنs: Sensor Signal Conditioning, Audio Preamplifier Stages, Industrial Control and Monitoring, Battery-Powered Embedded Systems, Analog-to-Digital Converter Input Buffering, Window Comparators and Threshold Detection.
Sensor Signal Conditioning
The LM358APT is well suited to conditioning resistive, bridge, or level-sensing signals that require modest amplification and filtering. The two independent channels allow one stage to amplify a sensor output while the other provides feedback, buffering, or active filtering. Because the device is specified as a low-power dual general-purpose amplifier, it is appropriate for compact battery-powered instruments where continuous analog operation must balance accuracy against energy use. Confirm that the sensor's common-mode voltage stays inside the amplifier input range and that output swing remains sufficient at the selected supply voltage.
تجویز کردہ
Audio Preamplifier Stages
The LM358APT can form the input stage of a small audio preamplifier, microphone conditioner, or line-level buffer. Its internally compensated dual-amplifier architecture supports closed-loop gain settings using external resistors and permits one channel to amplify while the other drives a volume-control or monitoring path. Low-power biasing is useful in portable speakers, headphone accessories, and compact consumer audio products. The design must still verify input noise, output drive capability, output swing, and stability for the connected load and cable capacitance.
تجویز کردہ
Industrial Control and Monitoring
The LM358APT is useful in industrial control boards for amplifying sensor outputs, implementing analog alarms, and driving comparator or supervisory inputs. Two channels can be allocated to independent loops, reducing the number of amplifier packages and simplifying shared grounding around an analog controller. The low-power operation is beneficial in continuously powered monitoring equipment. For designs exposed to large transients or long sensor wiring, add appropriate input protection and verify the amplifier's common-mode range, output swing, noise immunity, and stability margin.
تجویز کردہ
Battery-Powered Embedded Systems
A low-power dual operational amplifier fits battery-operated data-acquisition, environmental monitoring, and portable instrumentation designs where two analog channels are required on a constrained board area. The LM358APT consolidates two amplifiers into one 8-TSSOP package, reducing component count and keeping the analog routing compact. Its internal compensation avoids external compensation networks in conventional closed-loop configurations. Specify the operating duty cycle, acceptable quiescent current, and off-state behavior, then confirm the required supply range and common-mode limits in the manufacturer datasheet.
تجویز کردہ
Analog-to-Digital Converter Input Buffering
The LM358APT can buffer an analog source before it reaches an ADC input, reducing loading of the source and providing an additional gain or filtering stage. One channel may drive the ADC while the other provides active filtering or a reference-buffer function. This arrangement is common in slow industrial digitization systems, panel controllers, and sensor-interface boards. Verify that the amplifier's output can reach the ADC's input range, that settling is fast enough for the sampling rate, and that the chosen gain does not amplify offset or noise beyond the measurement budget.
تجویز کردہ
Window Comparators and Threshold Detection
Two LM358APT channels can implement independent window-comparator functions or a dual-threshold detector around a control or monitoring system. Each amplifier compares its non-inverting input with a divided reference at its inverting input, and the two outputs can drive a microcontroller or logic interface. The dual arrangement reduces package count compared with two separate single amplifiers. Because this device is a general-purpose amplifier rather than a dedicated comparator, propagation delay and output-transition behavior under overdrive must be checked against the system timing requirements.
تجویز کردہ
تجویز کردہ پروڈکٹس کا خلاصہ
کے لیے انجینئرنگ ریفرنس ڈیٹا LM358APT — موازنہ، ڈیزائن رہنمائی، اور تعمیل کی معلومات۔
انتخاب کی گائیڈ
متبادلات کے ساتھ موازنہ
| پیرامیٹر | یہ پروڈکٹ | OPA2192IP | OPA277UA | TLV9002IPWR | MCP6001-I/SS | TLV2462IPWR | RC4558PZ |
|---|---|---|---|---|---|---|---|
| Brand | STMicroelectronics | Texas Instruments | Texas Instruments | Texas Instruments | Microchip Technology | Texas Instruments | Yageo |
| Package | 8-TSSOP | 8-TSSOP | 8-TSSOP | 8-TSSOP | 8-TSSOP | 8-TSSOP | 8-TSSOP |
| Amplifier Channels | 2 channels | 2 channels | 2 channels | 2 channels | 2 channels | 2 channels | 2 channels |
| Functional Category | Low-power general-purpose operational amplifier | Precision rail-to-rail operational amplifier | Precision operational amplifier | Low-power rail-to-rail operational amplifier | Low-power operational amplifier | Low-power operational amplifier | General-purpose operational amplifier |
اہم امتیازی خصوصیات
- Two general-purpose channels in a compact 8-TSSOP (بمقابلہOPA277UA)
- Conventional low-power general-purpose amplifier positioning (بمقابلہTLV9002IPWR)
- Single package supports two independent analog functions (بمقابلہMCP6001-I/SS)
ڈیزائن نوٹس
Place the LM358APT decoupling capacitor directly between the positive supply and ground pins, keeping the connection loop as small as practical. Route the ground return to the package ground pin without passing through the analog input area. If the amplifier drives an external connector, keep the sensitive input and feedback nets away from that trace. Good supply and return geometry reduces susceptibility to switching noise and prevents output instability that can otherwise be mistaken for an amplifier defect.
Keep the inverting-input node physically small because feedback-network components connect to it and parasitic capacitance there can alter stability and effective noise gain. Place feedback resistors close to the relevant input pins and connect non-inverting inputs through short, quiet traces. When the source is a high-impedance sensor, minimize leakage paths and consider guarding or shielding because input bias current can create an unintended voltage even in a correctly laid out circuit.
Do not treat the LM358APT as a rail-to-rail precision amplifier. Check the input common-mode range and output swing at the actual supply voltage, load current, and temperature before selecting the gain. Also verify the gain-bandwidth product and slew rate for the closed-loop gain and operating frequency. A signal that fits electrically but exceeds those limits can produce distortion, unexpected slew behavior, or oscillation during prototype testing.
تعمیل کی معلومات
The LM358APT catalog identity, dual amplifier configuration, and 8-TSSOP package are confirmed by distributor listings. Compliance declarations were not present in those listings and should be checked on the manufacturer product page for the exact ordering code.