LM358LVIDR - Dual 5.5V 1MHz Op Amp | Texas Instruments
MPN: LM358LVIDR ✓ فعالLM358LVIDR جائزہ
An operational amplifier, or op amp, is a voltage-controlled differential amplifier whose open-loop gain is high at low frequencies. In practical circuits, negative feedback causes the amplifier to follow a defined gain rather than operate as an open-loop comparator. The LM358LV belongs to the broader hierarchy of analog integrated circuits, specifically low-voltage operational amplifiers used for signal conditioning, buffering, amplification, and feedback in battery-powered and cost-sensitive equipment.
The LM358LVIDR's 2.7 V to 5.5 V operating range targets low-voltage systems where higher-voltage standard LM358 devices may be unnecessary. Its 1 MHz gain-bandwidth product supports general-purpose signal processing, while the dual configuration allows two related functions to share one package. Texas Instruments identifies applications including large appliances, smoke detectors, and personal electronics, where low supply voltage and cost are important design constraints.
This low-voltage member of the LM3xxLV family is intended to provide an alternative to the single LM321, dual LM358, and quad LM324 in applications sensitive to cost. Because the maximum supply is only 5.5 V, circuit designers must distinguish it from the wider-input-voltage standard LM358 and ensure that external transients do not exceed the device's operating limits. The same distinction applies when evaluating a footprint-compatible part.
Typical uses include sensor-signal conditioning, audio and communication interfaces, control-loop support, and low-voltage analog measurement systems. In a smoke detector or appliance control board, for example, two amplifier channels can condition a sensor signal and support an output or feedback function without requiring two separate single-channel packages.
When designing around the LM358LVIDR, verify the complete power rail, including startup overshoot and inductive coupling, against the 5.5 V maximum. Place input and output compensation capacitors close to their associated pins, maintain a low-impedance ground return, and check output-swing requirements across the intended load and common-mode range.
This product page combines the Texas Instruments family specifications with a focused drop-in assessment, package-aware comparison, application guidance, and practical PCB considerations for engineers evaluating the LM358LVIDR.
کے لیے ڈراپ اِن متبادل LM358LVIDR — یکساں پیکیج، پن سے پن مطابقت پذیر۔ مختلف پیکیج والے پرزے جن کے لیے PCB دوبارہ کام درکار ہو، شامل نہیں ہیں۔
LM358LVD
✅ ڈراپ-اِن ⚠️ تفصیلات غیر تصدیق شدہ📋 حوالہ جاتی متبادل (کیٹلاگ میں نہیں)
LM358LVIDR زیادہ سے زیادہ ریٹنگز اور برقی خصوصیات
| Number of Channels | 2 channels |
| Amplifier Type | Single-supply operational amplifier |
| Supply Voltage Range | 2.7 V to 5.5 V |
| Maximum Supply Voltage | 5.5 V |
| Gain-Bandwidth Product | 1 MHz |
| پیکیج | 8-pin SOIC |
| ماؤنٹنگ ٹائپ | Surface mount |
| RoHS اسٹیٹس | unknown |
| REACH Status | unknown |
| AEC-Q100 Qualification | not_applicable |
LM358LVIDR 8-pin soic پن کنفیگریشن گائیڈ
LM358LVIDR (8-pin soic پیکیج) کے لیے پن کنفیگریشن۔ اس اینالاگ کمپوننٹ میں اِن پٹ، آؤٹ پٹ اور پاور سپلائی پنز شامل ہیں۔ آفسیٹ نل، کمپنسیشن اور اِن ایبل پن کنفیگریشنز کے لیے مینوفیکچرر کے ڈیٹا شیٹ سے رجوع کریں۔ سگنل کنڈیشننگ اور ایمپلیفائر سرکٹس کے لیے مثالی۔
کے لیے تفصیلی پن آؤٹ ڈیٹا دستیاب نہیں LM358LVIDR.
رجوع کریں ڈیٹا شیٹ مکمل پن کنفیگریشن کے لیے۔
عام استعمالات
LM358LVIDR کے لیے موزوں ہے 6 ایپلیکیشنs: Low-Voltage Sensor Signal Conditioning, Smoke and Gas Detector Signal Path, Large Appliance Control Board, Portable and Personal Electronics, Audio Interface Buffering, Industrial Feedback and Control Loops.
Low-Voltage Sensor Signal Conditioning
The LM358LVIDR fits low-voltage sensor interfaces because its two channels can amplify and buffer signals within a 2.7 V to 5.5 V supply. Its 1 MHz gain-bandwidth product provides useful bandwidth for general-purpose pressure, temperature, and position sensing without requiring a high-speed amplifier. Place the active device close to the sensor input, use a low-impedance ground reference, and verify that the signal remains inside the amplifier's common-mode and output-swing limits. Stability must be checked against the selected feedback network and the capacitance presented by the sensor and wiring.
تجویز کردہ
Smoke and Gas Detector Signal Path
Texas Instruments identifies smoke detectors as an application for the LM358LV family, making the LM358LVIDR suitable for low-voltage sensing and control blocks. Two amplifier channels can support signal conditioning and feedback or threshold-related functions within one 8-pin SOIC. Because detector designs may use battery backup, supply transients, and long standby periods, the circuit must maintain the rail within 2.7 V to 5.5 V and verify power consumption and startup behavior for the complete assembly.
تجویز کردہ
Large Appliance Control Board
The LM358LVIDR is appropriate for low-voltage control sections of large appliances where a dual amplifier can condition feedback or sensor signals while running from a 5 V rail. The 1 MHz bandwidth accommodates many slow control loops, and the SOIC-8 package supports compact surface-mount layouts. Designers should isolate switching supplies and motor-drive nodes from sensitive analog wiring, verify the rail during compressor and relay transitions, and include local bypass capacitance close to the device.
تجویز کردہ
Portable and Personal Electronics
The 2.7 V minimum supply makes the LM358LVIDR relevant to portable and personal-electronics products operating from 3 V or 5 V rails. Its dual-channel configuration can reduce the component count when the product needs both signal conditioning and an additional buffered analog function. The 1 MHz bandwidth is well matched to audio-adjacent, control, and sensor paths rather than high-frequency signal chains. Battery life depends on the complete circuit, so confirm quiescent current and leakage requirements for the operating mode.
تجویز کردہ
Audio Interface Buffering
The LM358LVIDR can provide general-purpose buffering and modest gain stages in a 5 V audio interface, subject to its 1 MHz bandwidth and output-swing limits. Using the two channels for input attenuation and output buffering can simplify a low-cost analog path. Keep the feedback network short, terminate unused channels according to the manufacturer's recommendations, and avoid using this device where the full rail-to-rail swing or very low noise of a dedicated audio amplifier is required.
تجویز کردہ
Industrial Feedback and Control Loops
The LM358LVIDR is suitable for low-voltage industrial feedback loops where the control rail remains within 2.7 V to 5.5 V. The dual package can amplify a feedback signal and condition a reference or sensor input, while the 1 MHz bandwidth supports loops far below that frequency. For factory equipment, isolate the analog section from motor and switching noise, use a defined ground strategy, and verify that startup, load transients, and fault conditions cannot push the device outside its 5.5 V supply limit.
تجویز کردہ
تجویز کردہ پروڈکٹس کا خلاصہ
کے لیے انجینئرنگ ریفرنس ڈیٹا LM358LVIDR — موازنہ، ڈیزائن رہنمائی، اور تعمیل کی معلومات۔
انتخاب کی گائیڈ
متبادلات کے ساتھ موازنہ
| پیرامیٹر | یہ پروڈکٹ | LM358LVD |
|---|---|---|
| Brand | Texas Instruments | Texas Instruments |
| Package | 8-pin SOIC | 8-pin SOIC |
| Number of Channels | 2 channels | 2 channels |
| Supply Voltage Range | 2.7 V to 5.5 V | 2.7 V to 5.5 V |
| Maximum Supply Voltage | 5.5 V | 5.5 V |
| Gain-Bandwidth Product | 1 MHz | 1 MHz |
| Amplifier Architecture | Dual operational amplifier | Dual operational amplifier |
| RoHS Status | unknown | unknown |
| REACH Status | unknown | unknown |
اہم امتیازی خصوصیات
- Purpose-built low-voltage supply range (بمقابلہStandard LM358)
- Compact dual-channel integration (بمقابلہTwo separate single-channel amplifiers)
- General-purpose bandwidth for low-voltage control (بمقابلہHigh-speed precision amplifier)
ڈیزائن نوٹس
Design the LM358LVIDR power rail for a maximum of 5.5 V, including regulator tolerance, startup overshoot, load transients, and coupling from switching nodes. Place a local bypass capacitor close to the supply and ground pins to suppress high-frequency impedance. If the source rail can exceed 5.5 V, add appropriate limiting or isolation rather than assuming that the amplifier will tolerate the higher voltage.
Use the Texas Instruments SOIC-8 land pattern and route each channel with a short feedback loop. Keep the bypass capacitor, signal inputs, feedback components, and output traces away from high-current switching paths. A continuous ground plane under the device can improve return-path consistency, while careful placement of analog traces helps prevent common-mode pickup in sensor and audio applications.
Do not treat the LM358LV as an unrestricted substitute for the standard higher-voltage LM358. Confirm that the complete rail stays between 2.7 V and 5.5 V, that the input remains within the supported common-mode range, and that the required output swing is reachable into the chosen load. Also verify noise, bias current, settling behavior, and feedback-network stability when replacing an existing device.
تعمیل کی معلومات
The manufacturer product page and LM358LV family information identify the device as an industry-standard low-voltage operational amplifier. RoHS, REACH, halogen-free, and conflict-minerals status were not stated in the available product information and must be confirmed for the exact orderable suffix.