Texas Instruments

LM358LVIDR - Dual 5.5V 1MHz Op Amp | Texas Instruments

MPN: LM358LVIDR ✓ Hoạt động
2.7 V to 5.5 V Vdss 8-pin SOIC Package
MOQ: 1 |

LM358LVIDR Tóm tắt

The Texas Instruments LM358LVIDR is a dual-channel, low-voltage operational amplifier specified for a 2.7 V to 5.5 V supply, 1 MHz gain-bandwidth product, and operation from a single 5 V rail. It is packaged in an 8-pin SOIC. The device provides two independent amplifiers in one package, reducing board area when dual-channel signal conditioning is required.

An operational amplifier, or op amp, is a voltage-controlled differential amplifier whose open-loop gain is high at low frequencies. In practical circuits, negative feedback causes the amplifier to follow a defined gain rather than operate as an open-loop comparator. The LM358LV belongs to the broader hierarchy of analog integrated circuits, specifically low-voltage operational amplifiers used for signal conditioning, buffering, amplification, and feedback in battery-powered and cost-sensitive equipment.

The LM358LVIDR's 2.7 V to 5.5 V operating range targets low-voltage systems where higher-voltage standard LM358 devices may be unnecessary. Its 1 MHz gain-bandwidth product supports general-purpose signal processing, while the dual configuration allows two related functions to share one package. Texas Instruments identifies applications including large appliances, smoke detectors, and personal electronics, where low supply voltage and cost are important design constraints.

This low-voltage member of the LM3xxLV family is intended to provide an alternative to the single LM321, dual LM358, and quad LM324 in applications sensitive to cost. Because the maximum supply is only 5.5 V, circuit designers must distinguish it from the wider-input-voltage standard LM358 and ensure that external transients do not exceed the device's operating limits. The same distinction applies when evaluating a footprint-compatible part.

Typical uses include sensor-signal conditioning, audio and communication interfaces, control-loop support, and low-voltage analog measurement systems. In a smoke detector or appliance control board, for example, two amplifier channels can condition a sensor signal and support an output or feedback function without requiring two separate single-channel packages.

When designing around the LM358LVIDR, verify the complete power rail, including startup overshoot and inductive coupling, against the 5.5 V maximum. Place input and output compensation capacitors close to their associated pins, maintain a low-impedance ground return, and check output-swing requirements across the intended load and common-mode range.

This product page combines the Texas Instruments family specifications with a focused drop-in assessment, package-aware comparison, application guidance, and practical PCB considerations for engineers evaluating the LM358LVIDR.

Bộ thay thế dễ dàng lắp đặt cho LM358LVIDR — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.

LM358LVD

✅ Drop-In ⚠️ Thông số chưa được xác minh
📦 8-pin SOIC
Same LM358LV 2.7 V to 5.5 V low-voltage family and 1 MHz class; order-code temperature and packing options must be checked

📋 Tham chiếu thay thế (không có trong danh mục)

LM358LVIDR Tỷ lệ tối đa & tính chất điện

Number of Channels 2 channels
Amplifier Type Single-supply operational amplifier
Supply Voltage Range 2.7 V to 5.5 V
Maximum Supply Voltage 5.5 V
Gain-Bandwidth Product 1 MHz
Hộp 8-pin SOIC
Kiểu lắp đặt Surface mount
Trạng thái RoHS unknown
REACH Status unknown
AEC-Q100 Qualification not_applicable

Hướng dẫn cấu hình chân LM358LVIDR 8-pin soic

Cấu hình chân cho LM358LVIDR (8-pin soic gói). Thành phần số hiệu này có chân đầu vào, đầu ra và nguồn cung cấp. Tham khảo tài liệu thông số kỹ thuật của nhà sản xuất để biết cấu hình chân bù, bù trừ và chân kích hoạt. Hoàn hảo cho điều kiện tín hiệu và mạch khuếch đại.

Bảng cấu hình chân 8-pin soic cho LM358LVIDR

Không có dữ liệu chân cụ thể sẵn có cho LM358LVIDR.

Tham khảo: tài liệu kỹ thuật cho cấu hình chân đầy đủ.

Ứng dụng tiêu biểu

LM358LVIDR phù hợp cho 6 Áp dụngs: Low-Voltage Sensor Signal Conditioning, Smoke and Gas Detector Signal Path, Large Appliance Control Board, Portable and Personal Electronics, Audio Interface Buffering, Industrial Feedback and Control Loops.

🧩

Low-Voltage Sensor Signal Conditioning

The LM358LVIDR fits low-voltage sensor interfaces because its two channels can amplify and buffer signals within a 2.7 V to 5.5 V supply. Its 1 MHz gain-bandwidth product provides useful bandwidth for general-purpose pressure, temperature, and position sensing without requiring a high-speed amplifier. Place the active device close to the sensor input, use a low-impedance ground reference, and verify that the signal remains inside the amplifier's common-mode and output-swing limits. Stability must be checked against the selected feedback network and the capacitance presented by the sensor and wiring.

🏭

Smoke and Gas Detector Signal Path

Texas Instruments identifies smoke detectors as an application for the LM358LV family, making the LM358LVIDR suitable for low-voltage sensing and control blocks. Two amplifier channels can support signal conditioning and feedback or threshold-related functions within one 8-pin SOIC. Because detector designs may use battery backup, supply transients, and long standby periods, the circuit must maintain the rail within 2.7 V to 5.5 V and verify power consumption and startup behavior for the complete assembly.

⚡

Large Appliance Control Board

The LM358LVIDR is appropriate for low-voltage control sections of large appliances where a dual amplifier can condition feedback or sensor signals while running from a 5 V rail. The 1 MHz bandwidth accommodates many slow control loops, and the SOIC-8 package supports compact surface-mount layouts. Designers should isolate switching supplies and motor-drive nodes from sensitive analog wiring, verify the rail during compressor and relay transitions, and include local bypass capacitance close to the device.

📱

Portable and Personal Electronics

The 2.7 V minimum supply makes the LM358LVIDR relevant to portable and personal-electronics products operating from 3 V or 5 V rails. Its dual-channel configuration can reduce the component count when the product needs both signal conditioning and an additional buffered analog function. The 1 MHz bandwidth is well matched to audio-adjacent, control, and sensor paths rather than high-frequency signal chains. Battery life depends on the complete circuit, so confirm quiescent current and leakage requirements for the operating mode.

🎧

Audio Interface Buffering

The LM358LVIDR can provide general-purpose buffering and modest gain stages in a 5 V audio interface, subject to its 1 MHz bandwidth and output-swing limits. Using the two channels for input attenuation and output buffering can simplify a low-cost analog path. Keep the feedback network short, terminate unused channels according to the manufacturer's recommendations, and avoid using this device where the full rail-to-rail swing or very low noise of a dedicated audio amplifier is required.

🏭

Industrial Feedback and Control Loops

The LM358LVIDR is suitable for low-voltage industrial feedback loops where the control rail remains within 2.7 V to 5.5 V. The dual package can amplify a feedback signal and condition a reference or sensor input, while the 1 MHz bandwidth supports loops far below that frequency. For factory equipment, isolate the analog section from motor and switching noise, use a defined ground strategy, and verify that startup, load transients, and fault conditions cannot push the device outside its 5.5 V supply limit.

What are the key specifications of LM358LVIDR that engineers should know?
The LM358LVIDR is a dual operational amplifier for a 2.7 V to 5.5 V supply with a 1 MHz gain-bandwidth product in an 8-pin SOIC package. Texas Instruments describes the device as an industry-standard low-voltage alternative to the LM321, LM358, and LM324. Its two independent channels support signal conditioning, buffering, and feedback functions, while its 5.5 V maximum supply requires careful rail design.
What is the operating voltage range of LM358LVIDR?
The LM358LVIDR operates from 2.7 V to 5.5 V according to the Texas Instruments LM358LV product page. This low-voltage range distinguishes the LV device from the standard LM358, which supports a substantially higher supply range. Any supply noise, startup overshoot, or coupled transient that raises the pin voltage above 5.5 V can damage the amplifier or disrupt normal operation.
Where can I download the LM358LVIDR datasheet PDF?
The official LM358LV device details and datasheet are available on the Texas Instruments product page at https://www.ti.com/product/LM358LV/part-details/LM358LVIDR. The LM358LV family documentation covers the single LM321LV, dual LM358LV, and quad LM324LV devices. Use the manufacturer's pin-description table when assigning PCB nets and checking the orderable package drawing.
Where can I find the LM358LVIDR pinout and SOIC-8 footprint?
The LM358LVIDR uses an 8-pin SOIC footprint, and its authoritative pin descriptions are shown in the Texas Instruments LM358LV datasheet. The manufacturer device page provides the downloadable documentation and orderable package information. Use that pin table for net names and the SOIC-8 land pattern for PCB layout rather than relying on a generic amplifier diagram.
Can LM358LVIDR replace a standard LM358 in a 5 V circuit?
The LM358LVIDR can serve as a footprint-compatible choice in a 5 V circuit when the complete signal and supply conditions meet its 2.7 V to 5.5 V operating range. The standard LM358 allows a higher maximum supply, so it cannot be assumed that the LV part is suitable for every original LM358 application. Verify supply transients, output swing, common-mode range, and stability requirements before substitution.
What can replace LM358LVIDR?
The closest documented same-footprint replacement is another suitably rated SOIC-8 low-voltage dual operational amplifier, but a qualified alternate must match pinout, supply range, gain-bandwidth, output swing, and load behavior. The LM358LV family part LM358LVD is the practical same-brand family alternative because it retains the low-voltage architecture and SOIC-8 ordering format. Cross-brand substitutions should be approved only after checking the original manufacturer's electrical limits.
Is LM358LVIDR the same as LM358LVD?
LM358LVIDR and LM358LVD identify orderable versions within the same LM358LV low-voltage dual-amplifier family, but their order codes can specify different packing and grade options. They should not be treated as different functional architectures. For a PCB replacement, confirm that the selected suffix maps to the same 8-pin SOIC footprint and that temperature, qualification, reel configuration, and production requirements satisfy the design.
Where can I buy LM358LVIDR online?
The LM358LVIDR can be requested through the Request a Quote form on this product page, where the required quantity, package code, and delivery requirements should be stated. The Texas Instruments product page also provides ordering information and technical documentation. Distributor listings indicate market availability, but current allocation, minimum order quantity, and lead time should be confirmed through the quote process.
What is the price of LM358LVIDR?
Current commercial terms for LM358LVIDR are obtained through the Request a Quote form on this page. The visible quote workflow is the appropriate place to request unit pricing for your required quantities rather than relying on a static marketplace figure. Include the exact suffix LM358LVIDR, SOIC-8 package requirement, target quantity, and destination when submitting the request.
What is the lead time for LM358LVIDR?
The current lead time for LM358LVIDR should be requested through the Request a Quote form on this page. Lead time can vary with order quantity, packaging configuration, production scheduling, and shipment destination. A distributor listing alone does not establish a guaranteed delivery date, so use the quote response for planning purposes rather than treating general inventory information as a firm schedule.
Is LM358LVIDR in stock?
LM358LVIDR is shown by distributors as an orderable component, but a specific stock quantity should be confirmed through the Request a Quote form on this page. Distributor status can change quickly, and an in-stock listing may not cover the exact quantity or packing configuration required by your production schedule. The quote response should be used to confirm allocation and expected dispatch timing.
What is the difference between LM358LVIDR and the standard LM358?
The principal difference is the supply-voltage class: LM358LVIDR operates from 2.7 V to 5.5 V, while the standard LM358 is intended for higher-voltage operation. Both provide two amplifiers in an 8-pin SOIC-style package, but maximum supply voltage, bias current, noise, and several other electrical limits can differ. The LV version is appropriate when the circuit intentionally operates below its lower-voltage ceiling.
When should I choose LM358LVIDR over a higher-voltage dual op amp?
Choose LM358LVIDR when the system supply is constrained to 2.7 V through 5.5 V and the application needs a general-purpose dual amplifier with approximately 1 MHz bandwidth. It is especially suitable for cost-sensitive low-voltage appliances, smoke detectors, and personal electronics. Choose a higher-voltage amplifier instead when the rail, transient margin, input range, output swing, or noise requirements exceed the LV family's limits.
Is LM358LVIDR suitable for battery-powered sensor interfaces?
The LM358LVIDR is suitable for many 3 V to 5 V battery-powered sensor interfaces because its supply range begins at 2.7 V and it provides two amplifier channels. A practical design must still confirm quiescent current, input bias current, common-mode behavior, and output swing under the actual battery voltage. Its 1 MHz bandwidth is sufficient for many general-purpose sensing and conditioning paths.
Does LM358LVIDR require external decoupling?
The LM358LVIDR should be used with appropriate power-supply bypassing to control impedance and noise at the device pins. Texas Instruments specifies stable operation with external compensation in the LM358LV datasheet, and the recommended capacitor values and layout should be followed for the selected gain and stability configuration. Place the supply bypass capacitor close to the power and ground pins to minimize parasitic inductance.
What design trade-offs should I check before using LM358LVIDR?
The main trade-offs are the 5.5 V maximum supply, 1 MHz bandwidth, and low-voltage operating class. Designers should verify rail tolerance, startup overshoot, output swing into the intended load, common-mode input limits, noise requirements, and whether the chosen feedback network is stable. These checks determine whether the low-voltage architecture provides enough margin without requiring a higher-voltage or higher-performance amplifier.

Dữ liệu tham khảo kỹ thuật cho LM358LVIDR — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.

Hướng dẫn chọn lựa

Choose the LM358LVIDR for cost-sensitive 2.7 V to 5.5 V systems that need two general-purpose amplifier channels in an 8-pin SOIC. It is particularly suitable for smoke-detector, appliance-control, portable-device, sensor-conditioning, and low-voltage feedback circuits where approximately 1 MHz bandwidth is sufficient. LM358LVD is the practical same-brand family alternative when the SOIC footprint and low-voltage electrical class are preserved, although temperature and order-code options must be checked. A standard LM358 remains preferable when the circuit can operate above 5.5 V or requires its wider supply range. Before replacing another amplifier, verify common-mode range, output swing, input offset, bias current, noise, load drive, and compensation requirements. The LV part is a functional choice for properly bounded 3 V and 5 V circuits, not a universal substitute for every standard-LM358 application.

So sánh với các sản phẩm thay thế

Tham số Sản phẩm này LM358LVD
Brand Texas Instruments Texas Instruments
Package 8-pin SOIC 8-pin SOIC
Number of Channels 2 channels 2 channels
Supply Voltage Range 2.7 V to 5.5 V 2.7 V to 5.5 V
Maximum Supply Voltage 5.5 V 5.5 V
Gain-Bandwidth Product 1 MHz 1 MHz
Amplifier Architecture Dual operational amplifier Dual operational amplifier
RoHS Status unknown unknown
REACH Status unknown unknown

Bảo phân biệt quan trọng

  • Purpose-built low-voltage supply range (vsStandard LM358)
  • Compact dual-channel integration (vsTwo separate single-channel amplifiers)
  • General-purpose bandwidth for low-voltage control (vsHigh-speed precision amplifier)

Ghi chú thiết kế

Design the LM358LVIDR power rail for a maximum of 5.5 V, including regulator tolerance, startup overshoot, load transients, and coupling from switching nodes. Place a local bypass capacitor close to the supply and ground pins to suppress high-frequency impedance. If the source rail can exceed 5.5 V, add appropriate limiting or isolation rather than assuming that the amplifier will tolerate the higher voltage.

Use the Texas Instruments SOIC-8 land pattern and route each channel with a short feedback loop. Keep the bypass capacitor, signal inputs, feedback components, and output traces away from high-current switching paths. A continuous ground plane under the device can improve return-path consistency, while careful placement of analog traces helps prevent common-mode pickup in sensor and audio applications.

Do not treat the LM358LV as an unrestricted substitute for the standard higher-voltage LM358. Confirm that the complete rail stays between 2.7 V and 5.5 V, that the input remains within the supported common-mode range, and that the required output swing is reachable into the chosen load. Also verify noise, bias current, settling behavior, and feedback-network stability when replacing an existing device.

Thông tin tuân thủ

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
Không chì
Unknown
Không halogen
Unknown
Khoáng vật xung đột
Unknown

The manufacturer product page and LM358LV family information identify the device as an industry-standard low-voltage operational amplifier. RoHS, REACH, halogen-free, and conflict-minerals status were not stated in the available product information and must be confirmed for the exact orderable suffix.

Tìm kiếm liên quan

LM358LVIDR datasheet LM358LVIDR pinout LM358LVIDR datasheet pdf LM358LVIDR specifications Texas Instruments LM358LVIDR LM358LVIDR equivalent LM358LVIDR replacement LM358LVIDR cross reference LM358LVIDR SOIC-8 footprint LM358LVIDR 5.5V 1MHz LM358LVIDR application circuit LM358LVIDR price LM358LVIDR stock LM358LVIDR vs LM358LVD

Các bộ phận và thuật ngữ liên quan

Texas Instruments LM358LVIDR LM358LVD LM358LV LM358 LM321LV LM324LV dual operational amplifier low-voltage operational amplifier analog integrated circuit semiconductor single-supply amplifier signal conditioning voltage buffering gain-bandwidth product common-mode input range output swing feedback network SOIC-8 surface-mount package smoke detector large appliance portable electronics industrial control battery-powered sensor
Báo giá nhanh RFQ
Hãy điền đầy đủ thông tin — đội ngũ bán hàng của chúng tôi sẽ phản hồi trong vòng 24 giờ
Mã sản phẩm Nhà sản xuất Kiểu đóng gói QTY Giá mục tiêu Phụ
✓
Báo giá đã gửi!

Chúng tôi sẽ trả lời email của bạn trong vòng 24 giờ

1
RFQ đã gửi
2
Phiếu báo giá nhận được
3
Đặt hàng thành công
4
Thanh toán
5
Đã gửi
6
Đã giao hàng
Xem chi tiết RFQ