LT1167CS8 - Precision Sensor INA | Analog Devices
MPN: LT1167CS8 ✓ فعالLT1167CS8 جائزہ
An instrumentation amplifier is a differential amplifier optimized for measuring small signals embedded in larger common-mode voltages. The LT1167CS8 combines high input impedance, precise gain control, and common-mode rejection in one compact package. This makes it suitable within the measurement-instrumentation amplifier category for bridge sensors, biomedical signals, and precision analog front ends where a conventional operational amplifier would require additional matching resistors or differential input stages.
The defining feature is single-resistor gain programming. Setting the external gain resistor between the designated gain pins establishes gains from 1 to 10,000 without the dual-resistor networks often required by three-amplifier instrumentation amplifiers. A 7.5 nV/√Hz noise density at 1 kHz supports low-noise measurement, while the 0.9 mA typical supply current supports low-power operation across a 2.3 V to 15 V supply range.
Its three-amplifier architecture provides differential input handling and high common-mode rejection. The manufacturer states that two external 5 kΩ resistors allow the LT1167 to pass the IEC 1000-4-2 Level 4 electrostatic-discharge specification. This protection capability is useful when the sensor interface can be connected to an external cable or touch-accessible equipment.
Typical uses include strain-gauge and load-cell front ends, isolated sensor measurement, precision bridge excitation, medical instrumentation, and low-level process-control signals. The 8-pin SOIC package also reduces board area compared with discrete multi-amplifier and precision-resistor implementations, simplifying signal-chain integration.
Design attention should be concentrated on gain-resistor selection, input filtering, reference grounding, supply bypassing, and common-mode-range checks. Stable gain requires suitable resistor construction and layout, while high-gain operation amplifies thermal and layout-induced errors. Confirm the complete operating limits and pin assignments in the manufacturer datasheet before releasing a PCB.
This product page consolidates manufacturer specifications, package and pin information, qualified same-footprint alternatives, application guidance, and design checks into a practical engineering reference for selecting and implementing the LT1167CS8.
کے لیے ڈراپ اِن متبادل LT1167CS8 — یکساں پیکیج، پن سے پن مطابقت پذیر۔ مختلف پیکیج والے پرزے جن کے لیے PCB دوبارہ کام درکار ہو، شامل نہیں ہیں۔
اس سیریز میں مختلف ورژن
اسی سیریز کے ماڈلز جو ڈراپ اِن مطابقت رکھتے ہیں LT1167CS8 (یکساں فارم فیکٹر اور فٹ پرنٹ) — میں مختلف Gain Range, Number of Circuits, Package, Voltage Noise Density.
LT1167CS8#PBF
✅ ڈراپ-اِن📋 حوالہ جاتی متبادل (کیٹلاگ میں نہیں)
LT1167IS8#PBF
✅ ڈراپ-اِن📋 حوالہ جاتی متبادل (کیٹلاگ میں نہیں)
LT1167AIS8#PBF
✅ ڈراپ-اِن📋 حوالہ جاتی متبادل (کیٹلاگ میں نہیں)
LT1167CS8-1#TRPBF
✅ ڈراپ-اِن📋 حوالہ جاتی متبادل (کیٹلاگ میں نہیں)
LT1161CSW#TRPBF
✅ ڈراپ-اِن📋 حوالہ جاتی متبادل (کیٹلاگ میں نہیں)
LT1167CS8 زیادہ سے زیادہ ریٹنگز اور برقی خصوصیات
| Product Type | Precision instrumentation amplifier |
| Number of Circuits | 1 circuit |
| Gain Range | 1 to 10,000 V/V |
| Gain Programming Method | One external resistor |
| Voltage Noise Density | 7.5 nV/√Hz at 1 kHz |
| Typical Supply Current | 0.9 mA |
| Supply Voltage Range | 2.3 V to 15 V |
| Maximum Supply Voltage | ±18 V |
| ESD Protection | IEC 1000-4-2 Level 4 with two external 5 kΩ resistors |
| پیکیج | 8-pin SOIC |
| ماؤنٹنگ ٹائپ | Surface mount |
LT1167CS8 پن کنفیگریشن
| پن 1 | RG — Gain-setting resistor terminal |
| پن 2 | -IN — Inverting input |
| پن 3 | +IN — Non-inverting input |
| پن 4 | -VS — Negative supply |
| پن 5 | REF — Reference input |
| پن 6 | OUT — Amplified output |
| پن 7 | +VS — Positive supply |
| پن 8 | RG — Gain-setting resistor terminal |
عام استعمالات
LT1167CS8 کے لیے موزوں ہے 6 ایپلیکیشنs: Strain-Gauge Bridge Measurement, Medical and Biopotential Front Ends, Industrial Process-Signal Conditioning, Portable Sensor and IoT Devices, Balanced Audio and Communication Inputs, Precision Data-Acquisition Front End.
Strain-Gauge Bridge Measurement
The LT1167CS8 is well suited to strain-gauge and load-cell bridges because it accepts differential inputs, provides gains from 1 to 10,000 using one external resistor, and offers 7.5 nV/√Hz noise density at 1 kHz. It can sit close to the bridge to minimize cable pickup and convert the small differential bridge voltage into a level suitable for an ADC. Keep excitation and bridge-return paths away from the gain node, and use a stable gain resistor when ratio accuracy is important. The main trade-off is that a single amplifier cannot correct bridge imbalance, temperature drift, or offset without additional calibration or compensation circuitry.
تجویز کردہ
Medical and Biopotential Front Ends
The LT1167CS8 can form the low-noise input stage of medical instrumentation when paired with suitable protection and isolation circuitry. Its 7.5 nV/√Hz noise density supports low-amplitude biopotential and pressure-sensor measurements, while single-resistor gain programming simplifies adjustment across multiple channels. The 8-pin SOIC footprint reduces analog-front-end area, but signal-path isolation, electrode protection, creepage, leakage, and electrode-site safety requirements remain system-level constraints. Keep the high-impedance input and gain nodes away from digital switching nodes, and validate the complete protection network against the intended medical standard.
تجویز کردہ
Industrial Process-Signal Conditioning
For low-level process signals, the LT1167CS8 provides differential rejection, 7.5 nV/√Hz noise density, and programmable gains up to 10,000 in a compact package. It is useful when a pressure, displacement, or current-to-voltage sensor produces a small differential voltage superimposed on a larger common-mode level. Place the amplifier near the sensor and use a reference arrangement appropriate to the ADC input range. Compared with a discrete multi-op-amp implementation, the integrated circuit reduces component count and board area, but designers must still budget for transient protection, grounding, gain-resistor accuracy, and adequate supply bypassing.
تجویز کردہ
Portable Sensor and IoT Devices
The LT1167CS8 suits compact battery-powered sensor products because its typical supply current is 0.9 mA and it operates from 2.3 V to 15 V. The single external gain resistor and 8-pin SOIC package leave more board area for sensing, processing, and radio circuitry. Low noise helps preserve small sensor signals, while the differential architecture rejects common-mode disturbance on short interconnects. Designers should power the amplifier close to its operating point to avoid wasting headroom, verify the output swing against the ADC range, and use a low-leakage gain resistor when operating at high gain.
تجویز کردہ
Balanced Audio and Communication Inputs
The LT1167CS8 can amplify balanced low-level signals in professional audio, communications, and line-interface equipment where differential input and adjustable gain are useful. Its single-resistor gain setting supports gains from 1 to 10,000, enabling the same basic front-end topology to cover several signal ranges. The 7.5 nV/√Hz noise density is beneficial for quiet signal paths, while the 8-pin SOIC package simplifies compact analog boards. Input and output filtering should be designed around the intended bandwidth, and the reference network must preserve a defined output bias when the source is absent.
تجویز کردہ
Precision Data-Acquisition Front End
The LT1167CS8 is appropriate ahead of high-resolution ADCs when the source is differential and the available signal is smaller than the converter's input range. Programmable gains from 1 to 10,000 let one amplifier family cover multiple sensor ranges, while 7.5 nV/√Hz noise density supports low-noise acquisition. Place the amplifier close to the ADC input to avoid adding cable or trace noise, and establish the reference level through a low-impedance network. The primary limitations are gain-resistor drift, common-mode-range restrictions, input bias-current errors, and the need to keep the gain node clean at high sensitivity.
تجویز کردہ
تجویز کردہ پروڈکٹس کا خلاصہ
کے لیے انجینئرنگ ریفرنس ڈیٹا LT1167CS8 — موازنہ، ڈیزائن رہنمائی، اور تعمیل کی معلومات۔
انتخاب کی گائیڈ
متبادلات کے ساتھ موازنہ
| پیرامیٹر | یہ پروڈکٹ | LT1167CS8#PBF | LT1167IS8#PBF | LT1167AIS8#PBF | LT1167CS8-1#TRPBF | LT1161CSW#TRPBF |
|---|---|---|---|---|---|---|
| Package | 8-pin SOIC | 8-pin SOIC | 8-pin SOIC | 8-pin SOIC | 8-pin SOIC | 8-pin SOIC |
| Brand | Analog Devices | Analog Devices | Analog Devices | Analog Devices | Analog Devices | Analog Devices |
| Product Type | Precision instrumentation amplifier | Precision instrumentation amplifier | Precision instrumentation amplifier | Precision instrumentation amplifier | Precision instrumentation amplifier | Single-resistor gain-programmable instrumentation amplifier |
| Gain Range | 1 to 10,000 V/V | 1 to 10,000 V/V | 1 to 10,000 V/V | 1 to 10,000 V/V | 1 to 10,000 V/V | 1 to 100 V/V |
| Gain Programming | One external resistor | One external resistor | One external resistor | One external resistor | One external resistor | One external resistor |
اہم امتیازی خصوصیات
- Wider programmable gain range within the same 8-pin SOIC footprint (بمقابلہLT1161CSW#TRPBF)
- Single-resistor gain programming reduces external matching components (بمقابلہLT1161CSW#TRPBF)
- Documented low-noise performance for precision signal chains (بمقابلہLT1167IS8#PBF)
ڈیزائن نوٹس
Place the LT1167CS8 close to the sensor or source and route the differential inputs as a short, closely coupled pair. Keep the gain-programming resistor and gain-node traces compact because parasitic capacitance and leakage can alter gain at high sensitivity. Avoid routing these nodes beneath digital clocks, switching-regulator nodes, or high-impedance leakage paths. Connect the reference and ground returns using the topology shown in the manufacturer's application circuits.
Do not assume that every 8-pin instrumentation amplifier is interchangeable with the LT1167CS8. Verify pin functions, gain-resistor connection, reference behavior, input and output common-mode limits, and supply range before substitution. The LT1161CSW#TRPBF, for example, is limited to a maximum gain of 100 rather than 10,000, so it cannot replace the LT1167CS8 in a high-gain application without redesigning the gain network.
For externally connected sensors, the Analog Devices documentation specifies two external 5 kΩ resistors for IEC 1000-4-2 Level 4 ESD capability. Implement those resistors in the signal path as directed by the manufacturer and combine them with appropriate common-mode and ground protection. ESD protection is only one layer of the design; enclosure grounding, cable routing, surge protection, and system-level fault recovery must also be addressed.
Decouple each supply rail close to the LT1167CS8 with the capacitance and ESR recommendations from the manufacturer datasheet. Verify startup behavior, output settling, and supply sequencing in single-supply operation because the reference level determines the usable output range. The device's typical 0.9 mA supply current is low, but accuracy also depends on clean rails and stable reference grounding.
تعمیل کی معلومات
The target LT1167CS8 and several ordered suffixes are listed with lead-free PBF or TRPBF markings, but no explicit compliance declaration for this exact non-PBF target MPN was identified. IEC 1000-4-2 Level 4 ESD capability is stated by the manufacturer when two external 5 kΩ resistors are used.