Analog Devices

LT1167CS8 - Precision Sensor INA | Analog Devices

部品番号: LT1167CS8 ✓ 生産中
7.5 nV/√Hz at 1 kHz Vdss 0.9 mA Id 8-pin SOIC Package
MOQ: 1 |

LT1167CS8 概要

Analog Devices LT1167CS8 is a low-power, precision instrumentation amplifier with a single-resistor gain setting from 1 to 10,000, 7.5 nV/√Hz voltage noise at 1 kHz, and an 8-pin SOIC package. It operates from ±18 V according to the manufacturer product documentation and is designed for accurate amplification of low-level differential sensor signals.

An instrumentation amplifier is a differential amplifier optimized for measuring small signals embedded in larger common-mode voltages. The LT1167CS8 combines high input impedance, precise gain control, and common-mode rejection in one compact package. This makes it suitable within the measurement-instrumentation amplifier category for bridge sensors, biomedical signals, and precision analog front ends where a conventional operational amplifier would require additional matching resistors or differential input stages.

The defining feature is single-resistor gain programming. Setting the external gain resistor between the designated gain pins establishes gains from 1 to 10,000 without the dual-resistor networks often required by three-amplifier instrumentation amplifiers. A 7.5 nV/√Hz noise density at 1 kHz supports low-noise measurement, while the 0.9 mA typical supply current supports low-power operation across a 2.3 V to 15 V supply range.

Its three-amplifier architecture provides differential input handling and high common-mode rejection. The manufacturer states that two external 5 kΩ resistors allow the LT1167 to pass the IEC 1000-4-2 Level 4 electrostatic-discharge specification. This protection capability is useful when the sensor interface can be connected to an external cable or touch-accessible equipment.

Typical uses include strain-gauge and load-cell front ends, isolated sensor measurement, precision bridge excitation, medical instrumentation, and low-level process-control signals. The 8-pin SOIC package also reduces board area compared with discrete multi-amplifier and precision-resistor implementations, simplifying signal-chain integration.

Design attention should be concentrated on gain-resistor selection, input filtering, reference grounding, supply bypassing, and common-mode-range checks. Stable gain requires suitable resistor construction and layout, while high-gain operation amplifies thermal and layout-induced errors. Confirm the complete operating limits and pin assignments in the manufacturer datasheet before releasing a PCB.

This product page consolidates manufacturer specifications, package and pin information, qualified same-footprint alternatives, application guidance, and design checks into a practical engineering reference for selecting and implementing the LT1167CS8.

ドロップイン代替品: LT1167CS8 — 同一パッケージでピン互換。PCBの作り直しが必要な異なるパッケージの部品は除外されています。

このシリーズのバリエーション

同一シリーズでドロップイン互換のモデル: LT1167CS8 (同一形状・フットプリント) — 相違点: Gain Range, Number of Circuits, Package, Voltage Noise Density.

Analog Devices
Gain Range: 1 to 10000
Number of Circuits: 1
Package: 8-Lead SOIC
比較対象 LT1167CS8 →

LT1167CS8#PBF

✅ ドロップイン
📦 8-pin SOIC
Same gain range of 1 to 10,000 and 7.5 nV/√Hz at 1 kHz; lead-free finish differs from the non-PBF LT1167CS8

📋 参考代替品(カタログ未掲載)

LT1167IS8#PBF

✅ ドロップイン
📦 8-pin SOIC
Same 1 to 10,000 gain range and 8-pin SOIC footprint; industrial temperature grade differs from the standard CS grade

📋 参考代替品(カタログ未掲載)

LT1167AIS8#PBF

✅ ドロップイン
📦 8-pin SOIC
Same 1 to 10,000 gain architecture and 8-pin SOIC footprint; automotive temperature grade differs from the standard CS grade

📋 参考代替品(カタログ未掲載)

LT1167CS8-1#TRPBF

✅ ドロップイン
📦 8-pin SOIC
Same 1 to 10,000 gain range and 8-pin SOIC footprint; grade-1 accuracy designation differs from the standard CS grade

📋 参考代替品(カタログ未掲載)

LT1161CSW#TRPBF

✅ ドロップイン
📦 8-pin SOIC
Same single-resistor gain-programming family and 8-pin SOIC footprint; maximum gain is 100 rather than 10,000, a 99% reduction in gain range

📋 参考代替品(カタログ未掲載)

LT1167CS8 最大定格&電気的特性

Product Type Precision instrumentation amplifier
Number of Circuits 1 circuit
Gain Range 1 to 10,000 V/V
Gain Programming Method One external resistor
Voltage Noise Density 7.5 nV/√Hz at 1 kHz
Typical Supply Current 0.9 mA
Supply Voltage Range 2.3 V to 15 V
Maximum Supply Voltage ±18 V
ESD Protection IEC 1000-4-2 Level 4 with two external 5 kΩ resistors
パッケージ 8-pin SOIC
実装タイプ Surface mount

LT1167CS8 ピン構成

SOIC-8 Package Pinout Diagram SOIC-8 8-pin small outline IC, 3.9x4.9mm, P1.27mm, JEDEC MS-012. 1 8 2 7 3 6 4 5 SOIC-8
ピン 1 RG — Gain-setting resistor terminal
ピン 2 -IN — Inverting input
ピン 3 +IN — Non-inverting input
ピン 4 -VS — Negative supply
ピン 5 REF — Reference input
ピン 6 OUT — Amplified output
ピン 7 +VS — Positive supply
ピン 8 RG — Gain-setting resistor terminal

主な用途

LT1167CS8 の用途: 6 件s: Strain-Gauge Bridge Measurement, Medical and Biopotential Front Ends, Industrial Process-Signal Conditioning, Portable Sensor and IoT Devices, Balanced Audio and Communication Inputs, Precision Data-Acquisition Front End.

🏭

Strain-Gauge Bridge Measurement

The LT1167CS8 is well suited to strain-gauge and load-cell bridges because it accepts differential inputs, provides gains from 1 to 10,000 using one external resistor, and offers 7.5 nV/√Hz noise density at 1 kHz. It can sit close to the bridge to minimize cable pickup and convert the small differential bridge voltage into a level suitable for an ADC. Keep excitation and bridge-return paths away from the gain node, and use a stable gain resistor when ratio accuracy is important. The main trade-off is that a single amplifier cannot correct bridge imbalance, temperature drift, or offset without additional calibration or compensation circuitry.

💊

Medical and Biopotential Front Ends

The LT1167CS8 can form the low-noise input stage of medical instrumentation when paired with suitable protection and isolation circuitry. Its 7.5 nV/√Hz noise density supports low-amplitude biopotential and pressure-sensor measurements, while single-resistor gain programming simplifies adjustment across multiple channels. The 8-pin SOIC footprint reduces analog-front-end area, but signal-path isolation, electrode protection, creepage, leakage, and electrode-site safety requirements remain system-level constraints. Keep the high-impedance input and gain nodes away from digital switching nodes, and validate the complete protection network against the intended medical standard.

🏭

Industrial Process-Signal Conditioning

For low-level process signals, the LT1167CS8 provides differential rejection, 7.5 nV/√Hz noise density, and programmable gains up to 10,000 in a compact package. It is useful when a pressure, displacement, or current-to-voltage sensor produces a small differential voltage superimposed on a larger common-mode level. Place the amplifier near the sensor and use a reference arrangement appropriate to the ADC input range. Compared with a discrete multi-op-amp implementation, the integrated circuit reduces component count and board area, but designers must still budget for transient protection, grounding, gain-resistor accuracy, and adequate supply bypassing.

🧩

Portable Sensor and IoT Devices

The LT1167CS8 suits compact battery-powered sensor products because its typical supply current is 0.9 mA and it operates from 2.3 V to 15 V. The single external gain resistor and 8-pin SOIC package leave more board area for sensing, processing, and radio circuitry. Low noise helps preserve small sensor signals, while the differential architecture rejects common-mode disturbance on short interconnects. Designers should power the amplifier close to its operating point to avoid wasting headroom, verify the output swing against the ADC range, and use a low-leakage gain resistor when operating at high gain.

🌐

Balanced Audio and Communication Inputs

The LT1167CS8 can amplify balanced low-level signals in professional audio, communications, and line-interface equipment where differential input and adjustable gain are useful. Its single-resistor gain setting supports gains from 1 to 10,000, enabling the same basic front-end topology to cover several signal ranges. The 7.5 nV/√Hz noise density is beneficial for quiet signal paths, while the 8-pin SOIC package simplifies compact analog boards. Input and output filtering should be designed around the intended bandwidth, and the reference network must preserve a defined output bias when the source is absent.

🖥️

Precision Data-Acquisition Front End

The LT1167CS8 is appropriate ahead of high-resolution ADCs when the source is differential and the available signal is smaller than the converter's input range. Programmable gains from 1 to 10,000 let one amplifier family cover multiple sensor ranges, while 7.5 nV/√Hz noise density supports low-noise acquisition. Place the amplifier close to the ADC input to avoid adding cable or trace noise, and establish the reference level through a low-impedance network. The primary limitations are gain-resistor drift, common-mode-range restrictions, input bias-current errors, and the need to keep the gain node clean at high sensitivity.

おすすめ製品の概要

LT1167CS8#PBF Lead-free same-package LT1167 variant 使用用途: Strain-Gauge Bridge Measurement, Industrial Process-Signal Conditioning, Portable Sensor and IoT Devices, Balanced Audio and Communication Inputs LT1167CS8-1#TRPBF Grade-1 same-package LT1167 variant 使用用途: Strain-Gauge Bridge Measurement, Portable Sensor and IoT Devices LT1167AIS8#PBF Automotive-temperature-grade family variant 使用用途: Medical and Biopotential Front Ends, Precision Data-Acquisition Front End LT1167IS8#PBF Industrial-temperature-grade family variant 使用用途: Medical and Biopotential Front Ends, Industrial Process-Signal Conditioning, Precision Data-Acquisition Front End LT1161CSW#TRPBF Related single-resistor instrumentation amplifier 使用用途: Balanced Audio and Communication Inputs
What is the LT1167CS8?
The LT1167CS8 is a single-resistor gain-programmable, precision instrumentation amplifier in an 8-pin SOIC package. According to the Analog Devices LT1167 product documentation, one external resistor sets gains from 1 to 10,000, while the device consumes 0.9 mA of typical supply current. Its differential-input architecture is intended for low-level sensor signals where common-mode noise and source impedance must be handled accurately.
How is the gain of the LT1167CS8 set?
The LT1167CS8 gain is set by one external resistor connected between its gain-programming pins, with supported gains from 1 to 10,000. This single-resistor approach replaces the paired resistor network commonly used by discrete three-amplifier instrumentation-amplifier designs. For high gains, use a stable resistor and maintain a compact, low-leakage layout around the gain node because resistance and parasitic capacitance can affect gain accuracy.
What is the voltage noise of the LT1167CS8?
The LT1167CS8 has 7.5 nV/√Hz voltage-noise density at 1 kHz. According to the Analog Devices LT1167 manufacturer page, this noise performance is maintained without increasing typical power dissipation above 0.9 mA across a 2.3 V to 15 V supply range. The result suits precision bridge, strain-gauge, biomedical, and process-signal interfaces where amplifier noise could limit the smallest detectable signal.
What supply voltage does the LT1167CS8 use?
The LT1167CS8 operates from a 2.3 V to 15 V supply according to the Analog Devices product documentation, with the part also identified as a ±18 V instrumentation amplifier in distributor product information. Dual-supply operation places the signal around ground, while single-supply designs require careful reference-voltage selection so input and output signals remain within the amplifier's common-mode range.
Where can I download the LT1167CS8 datasheet PDF?
The official LT1167 datasheet and product information are available from Analog Devices at https://www.analog.com/en/products/lt1167.html. The manufacturer page provides the electrical characteristics, gain-setting information, typical applications, and package information needed to evaluate the amplifier. Use the pin-description table and recommended application circuits in that document when assigning PCB nets and choosing external components.
Where can I find the LT1167CS8 pinout?
The LT1167CS8 pinout is shown in the Analog Devices LT1167 datasheet and its 8-pin SO package drawing. The eight connections provide the differential inputs, positive and negative supplies, reference and output, and the two gain-resistor terminals. Follow the package drawing when numbering physical pins, and verify every net against the manufacturer's pin-description table before fabrication.
Is the LT1167CS8 suitable for strain-gauge and bridge sensors?
The LT1167CS8 is suitable for strain-gauge and bridge-sensor interfaces because it combines differential input, single-resistor gain programming up to 10,000, and 7.5 nV/√Hz noise density at 1 kHz. Place it close to the bridge and excitation source, use a dedicated reference return, and keep high-impedance gain-node traces short to avoid adding leakage and noise to the measurement.
LT1167CS8 vs LT1167IS8#PBF - which is better for industrial use?
The LT1167IS8#PBF is generally the better selection when an industrial temperature grade is required, while the LT1167CS8 serves the standard commercial-temperature application. Both use the same 8-pin SOIC format and the same single-resistor gain-programming architecture. The exact temperature limits and grade-specific electrical parameters should be checked in the manufacturer documentation before substituting one for the other.
When should I choose the LT1167CS8 over a multi-amplifier design?
Choose the LT1167CS8 when the design needs differential input, one-resistor gain programming, and low power in a compact 8-pin SOIC. It replaces several discrete amplifiers and precision resistor networks while supporting gains from 1 to 10,000. A multi-amplifier design may still be preferable when independent gain adjustment, unusual common-mode ranges, or specialized isolation features are required.
Can the LT1167CS8 be used in medical instrumentation?
The LT1167CS8 can serve as the analog front end in medical instrumentation when the signal amplitude, frequency, safety architecture, and applicable equipment requirements are suitable. Its 7.5 nV/√Hz noise density and single-resistor gains of 1 to 10,000 are useful for low-level biopotential and sensor measurements. Medical-system compliance depends on the complete design and is not established by the amplifier alone.
What can replace the LT1167CS8?
The closest qualified drop-in choices are the same-family Analog Devices LT1167CS8#PBF, LT1167IS8#PBF, LT1167AIS8#PBF, and LT1167CS8-1#TRPBF, all using the same 8-pin SOIC footprint. Their availability, temperature grade, marking, and orderable suffix must be checked for the intended assembly. A generic SOIC instrumentation amplifier should not be assumed to be pin-compatible without a complete pin-function and parameter comparison.
Is there a verified cross-brand drop-in replacement for the LT1167CS8?
No verified cross-brand, pin-compatible replacement is identified for the LT1167CS8 in the available cross-reference results. The documented alternatives are primarily Analog Devices and legacy Linear Technology family variants. If an original component is unavailable, request a quote on this page and provide the required gain range, supply voltage, common-mode range, temperature grade, and acceptable footprint for engineering review.
How should the LT1167CS8 gain resistor be selected?
Select the LT1167CS8 gain resistor from the gain equation and required gain error in the manufacturer datasheet. Use a resistor with suitable initial tolerance, low temperature coefficient, and suitable power rating for the implemented gain. At high gain values, resistor leakage, contamination, moisture, and leakage from PCB surfaces can become significant, so protect the gain node and use clean, low-residue assembly practices.
How does the LT1167CS8 handle electrostatic discharge?
The LT1167CS8 can pass the IEC 1000-4-2 Level 4 electrostatic-discharge specification when fitted with two external 5 kΩ resistors, according to the Analog Devices product page. Those resistors must be positioned according to the manufacturer guidance. ESD qualification does not eliminate the need for enclosure design, grounding, cable management, and system-level surge protection.
Where can I buy the LT1167CS8, and what is its price?
The LT1167CS8 can be requested through the Request a Quote form on this page, where package, quantity, and delivery requirements can be reviewed with XAIPART. Current price, stock, and lead time are confirmed through that form rather than stated as static figures. Include the exact LT1167CS8 marking and required tube or reel packaging in the request.

エンジニアリング参考データ: LT1167CS8 — 比較、設計ガイダンス、コンプライアンス情報。

選定ガイド

Choose the LT1167CS8 for precision differential sensor measurements that need one-resistor gain programming, 7.5 nV/√Hz noise density, and operation from a compact 8-pin SOIC. Select LT1167IS8#PBF when the industrial temperature grade is required, or LT1167AIS8#PBF for the automotive-grade family option. LT1167CS8-1#TRPBF is appropriate when the grade-1 precision designation is specified. LT1167CS8#PBF provides a lead-finish option for the same electrical and package family. Consider LT1161CSW#TRPBF only when its maximum gain of 100 is sufficient; its 10,000-times lower maximum gain prevents it from serving as a functional replacement for high-gain LT1167CS8 designs. In every case, verify the exact suffix, temperature range, pin functions, supply limits, and gain accuracy before releasing production artwork.

代替品との比較

パラメータ この製品 LT1167CS8#PBF LT1167IS8#PBF LT1167AIS8#PBF LT1167CS8-1#TRPBF LT1161CSW#TRPBF
Package 8-pin SOIC 8-pin SOIC 8-pin SOIC 8-pin SOIC 8-pin SOIC 8-pin SOIC
Brand Analog Devices Analog Devices Analog Devices Analog Devices Analog Devices Analog Devices
Product Type Precision instrumentation amplifier Precision instrumentation amplifier Precision instrumentation amplifier Precision instrumentation amplifier Precision instrumentation amplifier Single-resistor gain-programmable instrumentation amplifier
Gain Range 1 to 10,000 V/V 1 to 10,000 V/V 1 to 10,000 V/V 1 to 10,000 V/V 1 to 10,000 V/V 1 to 100 V/V
Gain Programming One external resistor One external resistor One external resistor One external resistor One external resistor One external resistor

主な差別化要因

  • Wider programmable gain range within the same 8-pin SOIC footprint (vs LT1161CSW#TRPBF)
  • Single-resistor gain programming reduces external matching components (vs LT1161CSW#TRPBF)
  • Documented low-noise performance for precision signal chains (vs LT1167IS8#PBF)

設計ノート

Place the LT1167CS8 close to the sensor or source and route the differential inputs as a short, closely coupled pair. Keep the gain-programming resistor and gain-node traces compact because parasitic capacitance and leakage can alter gain at high sensitivity. Avoid routing these nodes beneath digital clocks, switching-regulator nodes, or high-impedance leakage paths. Connect the reference and ground returns using the topology shown in the manufacturer's application circuits.

Do not assume that every 8-pin instrumentation amplifier is interchangeable with the LT1167CS8. Verify pin functions, gain-resistor connection, reference behavior, input and output common-mode limits, and supply range before substitution. The LT1161CSW#TRPBF, for example, is limited to a maximum gain of 100 rather than 10,000, so it cannot replace the LT1167CS8 in a high-gain application without redesigning the gain network.

For externally connected sensors, the Analog Devices documentation specifies two external 5 kΩ resistors for IEC 1000-4-2 Level 4 ESD capability. Implement those resistors in the signal path as directed by the manufacturer and combine them with appropriate common-mode and ground protection. ESD protection is only one layer of the design; enclosure grounding, cable routing, surge protection, and system-level fault recovery must also be addressed.

Decouple each supply rail close to the LT1167CS8 with the capacitance and ESR recommendations from the manufacturer datasheet. Verify startup behavior, output settling, and supply sequencing in single-supply operation because the reference level determines the usable output range. The device's typical 0.9 mA supply current is low, but accuracy also depends on clean rails and stable reference grounding.

コンプライアンス情報

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
鉛フリー
Unknown
ハロゲンフリー
Unknown
紛争鉱物
Unknown

The target LT1167CS8 and several ordered suffixes are listed with lead-free PBF or TRPBF markings, but no explicit compliance declaration for this exact non-PBF target MPN was identified. IEC 1000-4-2 Level 4 ESD capability is stated by the manufacturer when two external 5 kΩ resistors are used.

データ検証日: 2026-11-14 — データはXAIPARTの部品エンジニアリングチームによって検証・管理されています

関連検索

lt1167cs8 trpbf lt1167cs8 pbf LT1167CS8 datasheet LT1167CS8 datasheet pdf LT1167CS8 pinout LT1167CS8 equivalent LT1167CS8 replacement LT1167CS8 cross reference LT1167CS8 vs LT1161CSW LT1167CS8 price LT1167CS8 SOIC-8 footprint LT1167CS8 strain gauge amplifier Analog Devices LT1167CS8 LT1167CS8 7.5 nV/Hz

関連部品&用語

Analog Devices LT1167CS8 LT1167CS8#PBF LT1167IS8#PBF LT1167AIS8#PBF LT1167CS8-1#TRPBF LT1161CSW#TRPBF instrumentation amplifier precision instrumentation amplifier single-resistor gain-programmable amplifier differential amplifier amplifier IC semiconductor 7.5 nV/√Hz voltage-noise density gain range common-mode rejection input offset voltage gain error supply current IEC 1000-4-2 Level 4 ESD protection 8-pin SOIC SOIC family surface-mount package strain-gauge bridge medical instrumentation industrial process control precision data acquisition
クイック見積RFQ
詳細をすべてご記入ください — 営業チームが24時間以内にご返信いたします
部品番号 メーカー パッケージ QTY 目標価格 小計
✓
見積を送信しました!

24時間以内にメールでご返信いたします

1
RFQ送信済み
2
見積受領
3
注文済み
4
お支払い
5
発送済み
6
配達済み
RFQの詳細を表示