MAX202EEUE+ - 5V 120kbps RS-232 Transceiver | Analog Devices
MPN: MAX202EEUE+ ✓ فعالMAX202EEUE+ جائزہ
An RS-232 transceiver is an interface IC that converts logic-level signals into RS-232-compatible levels and converts received RS-232 signals back into logic-level voltages. The MAX202EEUE+ belongs to the RS-232 interface IC hierarchy, where the MAX202E family combines integrated charge-pump circuitry, drivers, and receivers for single-supply operation. Its implementation supports RS-232 and V.28 communications while meeting EIA/TIA-232E and CCITT V.28 specifications at rates up to 120 kbps under load.
The principal features include two transmit channels, two receive channels, full-duplex operation, a 5 V supply, and ±15 kV human-body-model ESD protection. The integrated charge pump generates the bipolar voltage required by the RS-232 drivers, eliminating the need for an external negative supply. Dual-channel architecture allows two independent communication paths in one package, reducing board area compared with separate single-channel interface devices.
The MAX202EEUE+ family is intended for harsh communication environments where electrostatic discharge is a practical concern. Because the drivers and receivers satisfy EIA/TIA-232E and CCITT V.28 requirements at 120 kbps, the device is suitable for legacy serial links, industrial control ports, instrument interfaces, and service equipment. The 16-pin TSSOP package is surface mountable and can be placed on compact, high-density circuit boards.
Typical uses include PC-to-instrument RS-232 links, industrial controller data ports, configuration interfaces, and embedded systems that communicate with legacy peripherals. When connecting the device, keep the transceiver-side and logic-side ground strategy consistent with the connected equipment, place charge-pump capacitors close to their pins, and provide adequate input bypassing. Route the RS-232 traces away from sensitive analog and high-speed digital paths where practical.
The primary design trade-off is that this is a 5 V RS-232 interface rather than a modern differential interface. It supports established RS-232 infrastructure, but designers should not substitute it for RS-485 or RS-422 requirements involving longer cables, multidrop buses, or differential noise immunity. Verify connector pin assignments and signal direction before replacing an existing circuit.
This page combines the manufacturer family specifications with package details, application guidance, comparison parameters, and practical integration notes. It focuses on the distinctions engineers need when confirming supply voltage, channel count, data rate, ESD protection, package compatibility, and drop-in replacement options for the MAX202EEUE+.
کے لیے ڈراپ اِن متبادل MAX202EEUE+ — یکساں پیکیج، پن سے پن مطابقت پذیر۔ مختلف پیکیج والے پرزے جن کے لیے PCB دوبارہ کام درکار ہو، شامل نہیں ہیں۔
اس سیریز میں مختلف ورژن
اسی سیریز کے ماڈلز جو ڈراپ اِن مطابقت رکھتے ہیں MAX202EEUE+ (یکساں فارم فیکٹر اور فٹ پرنٹ) — میں مختلف Supply Voltage, Number of Drivers, Number of Receivers, Package, Charge Pump.
MAX202EUE
✅ ڈراپ-اِن📋 حوالہ جاتی متبادل (کیٹلاگ میں نہیں)
MAX202EUE+
✅ ڈراپ-اِنقیمت کے لیے رابطہ کریں
ڈیٹا شیٹ دیکھیں →MAX202ECUE+T
✅ ڈراپ-اِنقیمت کے لیے رابطہ کریں
ڈیٹا شیٹ دیکھیں →MAX202EEUE+ تفصیلات
| Product Type | Dual RS-232 transceiver |
| Number of Drivers | 2 |
| Number of Receivers | 2 |
| Duplex | Full duplex |
| سپلائی وولٹیج | 5 V |
| Maximum Data Rate | 120 kbps |
| ESD Protection | ±15 kV HBM |
| Interface Standard | EIA/TIA-232E |
| Interface Standard | CCITT V.28 |
| Communication Protocol | RS-232 |
| Charge Pump | Integrated |
| پیکیج | 16-pin TSSOP |
| ماؤنٹنگ ٹائپ | Surface mount |
MAX202EEUE+ 16-pin tssop پن کنفیگریشن گائیڈ
MAX202EEUE+ (16-pin tssop پیکیج) کے لیے پن کنفیگریشن۔ پن نمبرنگ، فنکشنز اور کنکشن ڈایاگرامز مینوفیکچرر کے ڈیٹا شیٹ میں بیان کیے گئے ہیں۔ درست فٹ پرنٹ اور سولڈرنگ رہنما ہدایات کے لیے اسی سے رجوع کریں۔
کے لیے تفصیلی پن آؤٹ ڈیٹا دستیاب نہیں MAX202EEUE+.
رجوع کریں ڈیٹا شیٹ مکمل پن کنفیگریشن کے لیے۔
عام استعمالات
MAX202EEUE+ کے لیے موزوں ہے 6 ایپلیکیشنs: Industrial Instrument Communication, Legacy PC Serial Port, Embedded Equipment Configuration Port, Point-to-Point Data Link, Test and Measurement Interface, Service and Diagnostic Connector.
Industrial Instrument Communication
The MAX202EEUE+ suits short-distance RS-232 links between an industrial instrument and a controller because it combines two drivers, two receivers, and ±15 kV HBM ESD protection in one 16-pin TSSOP package. The 5 V single-supply operation and integrated charge pump simplify system power design. At data rates up to 120 kbps, the interface can support legacy configuration and service ports. Designers should route the cable-side traces away from sensitive circuitry and use the manufacturer pin description when assigning driver outputs and receiver inputs.
تجویز کردہ
Legacy PC Serial Port
The MAX202EEUE+ provides the electrical interface required between modern controller logic and an RS-232 peripheral. Two full-duplex channels support simultaneous transmit and receive paths, while the integrated charge pump generates the required bipolar driver voltage from a single 5 V supply. Operation to 120 kbps covers many legacy serial-port protocols. The TSSOP-16 package reduces board area, but connector protection and correct logic-to-transceiver signal mapping remain essential during installation.
تجویز کردہ
Embedded Equipment Configuration Port
The MAX202EEUE+ is appropriate for service and configuration ports on embedded equipment that must communicate with a host through RS-232. Two channels allow separate command and diagnostic paths, and the 5 V operating requirement fits systems already using a 5 V control rail. Its ±15 kV HBM protection adds valuable resilience at an exposed connector boundary. Use short, properly referenced cable-side routing and place bypass and charge-pump capacitors close to their associated pins according to the manufacturer layout guidance.
تجویز کردہ
Point-to-Point Data Link
The MAX202EEUE+ supports a full-duplex point-to-point RS-232 data link at rates up to 120 kbps. This makes it suitable for legacy equipment where one controller exchanges commands and status with a remote peripheral through dedicated TX and RX conductors. Integrated charge-pump circuitry avoids a separate negative rail, while two transmit and two receive channels can serve two independent links. The design must observe RS-232 signal polarity and ground references rather than treating the interface as a balanced differential bus.
تجویز کردہ
Test and Measurement Interface
The MAX202EEUE+ can bridge legacy RS-232 test equipment to a control system while providing two full-duplex channels in a compact surface-mount package. Its 120 kbps capability is appropriate for many serial control protocols, and ±15 kV HBM protection improves robustness at accessible test ports. The single 5 V supply simplifies integration beside digital test circuitry. Confirm the exact connector wiring and device ground arrangement to avoid ground-loop or signal-polarity problems.
تجویز کردہ
Service and Diagnostic Connector
The MAX202EEUE+ is useful in service-oriented equipment that exposes an RS-232 diagnostic connector. The device provides the two drivers and two receivers needed for full-duplex diagnostics while operating from 5 V, and its ±15 kV HBM protection is relevant when service personnel connect cables to the system. The TSSOP-16 package supports compact board layouts. System designers should still apply appropriate enclosure grounding, connector shielding, and external surge protection when the cable environment exceeds direct human-body ESD exposure.
تجویز کردہ
تجویز کردہ پروڈکٹس کا خلاصہ
کے لیے انجینئرنگ ریفرنس ڈیٹا MAX202EEUE+ — موازنہ، ڈیزائن رہنمائی، اور تعمیل کی معلومات۔
انتخاب کی گائیڈ
متبادلات کے ساتھ موازنہ
| پیرامیٹر | یہ پروڈکٹ | MAX202EUE | MAX202EUE+ | MAX202ECUE+T |
|---|---|---|---|---|
| Brand | Analog Devices | Analog Devices | Analog Devices | Analog Devices |
| Package | TSSOP-16 | TSSOP-16 | TSSOP-16 | TSSOP-16 |
| Product Type | Dual RS-232 transceiver | Dual RS-232 transceiver | Dual RS-232 transceiver | Dual RS-232 transceiver |
| Number of Drivers | 2 | 2 | 2 | 2 |
| Number of Receivers | 2 | 2 | 2 | 2 |
| Supply Voltage | 5 V | 5 V | 5 V | 5 V |
| Maximum Data Rate | 120 kbps | 120 kbps | 120 kbps | 120 kbps |
| ESD Protection | ±15 kV HBM | ±15 kV HBM | ±15 kV HBM | ±15 kV HBM |
| Duplex | Full duplex | Full duplex | Full duplex | Full duplex |
| Charge Pump | Integrated | Integrated | Integrated | Integrated |
| Interface Standards | EIA/TIA-232E and CCITT V.28 | EIA/TIA-232E and CCITT V.28 | EIA/TIA-232E and CCITT V.28 | EIA/TIA-232E and CCITT V.28 |
اہم امتیازی خصوصیات
- Integrated dual-channel interface in one TSSOP package (بمقابلہMAX202EUE)
- Direct 5 V single-supply RS-232 operation (بمقابلہMAX202EUE+)
- High connector-side ESD resilience (بمقابلہMAX202ECUE+T)
ڈیزائن نوٹس
Place the charge-pump capacitors and supply bypass capacitors close to their associated MAX202EEUE+ pins, following the manufacturer datasheet layout and capacitor values. Keep the high-current driver return path compact and connect the device ground directly to the interface ground reference. Avoid routing RS-232 driver traces across long distances beneath unrelated digital circuitry, where switching currents could increase radiated or coupled noise.
Do not treat MAX202EEUE+ as an RS-485 or RS-422 interface. Its RS-232 architecture uses unbalanced signaling and is intended primarily for point-to-point communication. Verify driver-output and receiver-input direction, connector numbering, and logic polarity before PCB population. Reversing an RS-232 signal path can damage the interface even when the package and supply voltage are correct.
At exposed cable connectors, combine the device's ±15 kV HBM protection with sound mechanical and grounding practices. Keep exposed interface traces away from clocks, switching supplies, and high-impedance analog inputs. Use a low-inductance ground return and consider external surge protection when connected cables extend beyond a controlled equipment enclosure or may carry industrial transients.
Preserve the manufacturer pin numbering and package orientation when using any MAX202E catalog alternative in a TSSOP-16 design. The EUE ordering codes can differ in grade or packing interpretation, so review the complete ordering table before substitution. Check that any replacement remains a 5 V, two-driver, two-receiver RS-232 device with the required ESD rating and operating-temperature range.
تعمیل کی معلومات
The manufacturer family datasheet confirms RS-232, EIA/TIA-232E, CCITT V.28, ESD-protection, supply, and data-rate characteristics, but explicit RoHS, REACH, AEC-Q100, lead-free, halogen-free, and conflict-minerals declarations were not identified for the exact ordering code.