Analog Devices

MAX202EEUE+ - 5V 120kbps RS-232 Transceiver | Analog Devices

MPN: MAX202EEUE+ ✓ Aktif
5 V Vdss 16-pin TSSOP Package
MOQ: 1 |

MAX202EEUE+ Ringkasan

The Analog Devices MAX202EEUE+ is a dual-channel, full-duplex RS-232 transceiver with two drivers and two receivers, a 5 V single-supply operating requirement, data rates up to 120 kbps, and high ±15 kV ESD HBM protection. The device is packaged in a 16-pin TSSOP package designated EUE.

An RS-232 transceiver is an interface IC that converts logic-level signals into RS-232-compatible levels and converts received RS-232 signals back into logic-level voltages. The MAX202EEUE+ belongs to the RS-232 interface IC hierarchy, where the MAX202E family combines integrated charge-pump circuitry, drivers, and receivers for single-supply operation. Its implementation supports RS-232 and V.28 communications while meeting EIA/TIA-232E and CCITT V.28 specifications at rates up to 120 kbps under load.

The principal features include two transmit channels, two receive channels, full-duplex operation, a 5 V supply, and ±15 kV human-body-model ESD protection. The integrated charge pump generates the bipolar voltage required by the RS-232 drivers, eliminating the need for an external negative supply. Dual-channel architecture allows two independent communication paths in one package, reducing board area compared with separate single-channel interface devices.

The MAX202EEUE+ family is intended for harsh communication environments where electrostatic discharge is a practical concern. Because the drivers and receivers satisfy EIA/TIA-232E and CCITT V.28 requirements at 120 kbps, the device is suitable for legacy serial links, industrial control ports, instrument interfaces, and service equipment. The 16-pin TSSOP package is surface mountable and can be placed on compact, high-density circuit boards.

Typical uses include PC-to-instrument RS-232 links, industrial controller data ports, configuration interfaces, and embedded systems that communicate with legacy peripherals. When connecting the device, keep the transceiver-side and logic-side ground strategy consistent with the connected equipment, place charge-pump capacitors close to their pins, and provide adequate input bypassing. Route the RS-232 traces away from sensitive analog and high-speed digital paths where practical.

The primary design trade-off is that this is a 5 V RS-232 interface rather than a modern differential interface. It supports established RS-232 infrastructure, but designers should not substitute it for RS-485 or RS-422 requirements involving longer cables, multidrop buses, or differential noise immunity. Verify connector pin assignments and signal direction before replacing an existing circuit.

This page combines the manufacturer family specifications with package details, application guidance, comparison parameters, and practical integration notes. It focuses on the distinctions engineers need when confirming supply voltage, channel count, data rate, ESD protection, package compatibility, and drop-in replacement options for the MAX202EEUE+.

Pilihan pengganti yang segera untuk MAX202EEUE+ — sama paket, pin-pin kompatibel. Bahagian paket yang berbeza memerlukan kerja ulang PCB diasingkan.

Varietas dalam siri ini

Model serupa yang kompatibel dengan pengganti yang segera MAX202EEUE+ (sama faktor bentuk dan kaki) — berbeza dalam Supply Voltage, Number of Drivers, Number of Receivers, Package, Charge Pump.

Analog Devices
Supply Voltage: 5 V nominal, tolerant of ±10% supply variation
Number of Drivers: 2 channels
Number of Receivers: 2 channels
Bandingkan Dengan MAX202EEUE+ →
Analog Devices
Supply Voltage: +5 V single supply
Package: 16-TSSOP
Bandingkan Dengan MAX202EEUE+ →

MAX202EUE

✅ Masuk Drop-In
📦 TSSOP-16
Same 16-pin TSSOP MAX202E architecture; ordering suffix and grade details must be verified, with no verified numerical performance difference

📋 Alternatif rujukan (tidak dalam katalog)

MAX202EUE+

✅ Masuk Drop-In
Analog Devices
📦 TSSOP-16
RS-232 Transceiver · 2 · 2 · +5 V single supply · Up to 120 kbps (loaded, EIA/TIA-232E) · 4 x 0.1 uF · EIA/TIA-232E, CCITT V.28 · 16-TSSOP

Hubungi untuk harga

Lihat Datasheet →

MAX202ECUE+T

✅ Masuk Drop-In
Analog Devices
📦 TSSOP-16
Dual RS-232 transceiver with 2 drivers and 2 receivers · 2 channels · 2 channels · 5 V nominal, tolerant of ±10% supply variation · 120 kbps when loaded · EIA/TIA-232E and CCITT V.28 · ±15 kV human body model · Integrated, no external charge-pump capacitors required

Hubungi untuk harga

Lihat Datasheet →

MAX202EEUE+ Spesifikasi

Product Type Dual RS-232 transceiver
Number of Drivers 2
Number of Receivers 2
Duplex Full duplex
Tegangan Pemberi Arus 5 V
Maximum Data Rate 120 kbps
ESD Protection ±15 kV HBM
Interface Standard EIA/TIA-232E
Interface Standard CCITT V.28
Communication Protocol RS-232
Charge Pump Integrated
Kemasan 16-pin TSSOP
Jenis Pemasangan Surface mount

Panduan Konfigurasi Pin MAX202EEUE+ 16-pin tssop

Konfigurasi pin untuk MAX202EEUE+ (16-pin tssop pakai). Penomeran pin, fungsi, dan garis bentuk koneksi ditakrifkan dalam dokumen pengeluar. Rujuk dokumen untuk kebentuk dan pedoman pengasman.

Garis bentuk pengecah pakai 16-pin tssop untuk MAX202EEUE+

Tiada data garisan pin yang diperoleh untuk MAX202EEUE+.

Rujuk kepada lembaran data untuk konfigurasi pin penuh.

Aplikasi Biasa

MAX202EEUE+ patut untuk 6 aplikasis: Industrial Instrument Communication, Legacy PC Serial Port, Embedded Equipment Configuration Port, Point-to-Point Data Link, Test and Measurement Interface, Service and Diagnostic Connector.

🏭

Industrial Instrument Communication

The MAX202EEUE+ suits short-distance RS-232 links between an industrial instrument and a controller because it combines two drivers, two receivers, and ±15 kV HBM ESD protection in one 16-pin TSSOP package. The 5 V single-supply operation and integrated charge pump simplify system power design. At data rates up to 120 kbps, the interface can support legacy configuration and service ports. Designers should route the cable-side traces away from sensitive circuitry and use the manufacturer pin description when assigning driver outputs and receiver inputs.

🖥️

Legacy PC Serial Port

The MAX202EEUE+ provides the electrical interface required between modern controller logic and an RS-232 peripheral. Two full-duplex channels support simultaneous transmit and receive paths, while the integrated charge pump generates the required bipolar driver voltage from a single 5 V supply. Operation to 120 kbps covers many legacy serial-port protocols. The TSSOP-16 package reduces board area, but connector protection and correct logic-to-transceiver signal mapping remain essential during installation.

🔧

Embedded Equipment Configuration Port

The MAX202EEUE+ is appropriate for service and configuration ports on embedded equipment that must communicate with a host through RS-232. Two channels allow separate command and diagnostic paths, and the 5 V operating requirement fits systems already using a 5 V control rail. Its ±15 kV HBM protection adds valuable resilience at an exposed connector boundary. Use short, properly referenced cable-side routing and place bypass and charge-pump capacitors close to their associated pins according to the manufacturer layout guidance.

🌐

Point-to-Point Data Link

The MAX202EEUE+ supports a full-duplex point-to-point RS-232 data link at rates up to 120 kbps. This makes it suitable for legacy equipment where one controller exchanges commands and status with a remote peripheral through dedicated TX and RX conductors. Integrated charge-pump circuitry avoids a separate negative rail, while two transmit and two receive channels can serve two independent links. The design must observe RS-232 signal polarity and ground references rather than treating the interface as a balanced differential bus.

🔧

Test and Measurement Interface

The MAX202EEUE+ can bridge legacy RS-232 test equipment to a control system while providing two full-duplex channels in a compact surface-mount package. Its 120 kbps capability is appropriate for many serial control protocols, and ±15 kV HBM protection improves robustness at accessible test ports. The single 5 V supply simplifies integration beside digital test circuitry. Confirm the exact connector wiring and device ground arrangement to avoid ground-loop or signal-polarity problems.

⚡

Service and Diagnostic Connector

The MAX202EEUE+ is useful in service-oriented equipment that exposes an RS-232 diagnostic connector. The device provides the two drivers and two receivers needed for full-duplex diagnostics while operating from 5 V, and its ±15 kV HBM protection is relevant when service personnel connect cables to the system. The TSSOP-16 package supports compact board layouts. System designers should still apply appropriate enclosure grounding, connector shielding, and external surge protection when the cable environment exceeds direct human-body ESD exposure.

What is the MAX202EEUE+?
The MAX202EEUE+ is a dual-channel, full-duplex RS-232 transceiver with two drivers, two receivers, 5 V single-supply operation, and ±15 kV HBM ESD protection in a 16-pin TSSOP package. According to the Analog Devices MAX202E-MAX241E datasheet, its drivers and receivers meet EIA/TIA-232E and CCITT V.28 specifications at data rates up to 120 kbps when loaded.
What are the key specifications of MAX202EEUE+ that engineers should know?
The MAX202EEUE+ provides two drivers and two receivers, full-duplex RS-232 operation, a 5 V supply, and operation up to 120 kbps. It also includes an integrated charge pump and ±15 kV human-body-model ESD protection. The Analog Devices family datasheet identifies EIA/TIA-232E and CCITT V.28 compliance, while the EUE package is a 16-pin TSSOP configuration.
Where can I download the MAX202EEUE+ datasheet PDF?
The MAX202EEUE+ datasheet PDF can be downloaded from the official Analog Devices MAX202E-MAX241E datasheet link on this page. The document covers the MAX202E-MAX213E, MAX232E, and MAX241E transceiver family and includes general descriptions, features, specifications, pin information, and application guidance for the MAX202EEUE+.
Where can I find the MAX202EEUE+ pinout?
The MAX202EEUE+ pinout is found in the pin-description section of the official MAX202E-MAX241E manufacturer datasheet. Use that table when assigning power, ground, driver outputs, receiver inputs, and charge-pump capacitor connections. The EUE configuration uses a 16-pin TSSOP package, so verify pin numbering against the package drawing before laying out or modifying a PCB.
What is the MAX202EEUE+ supply voltage and data rate?
The MAX202EEUE+ operates from a single 5 V supply and supports data rates up to 120 kbps. According to the Analog Devices MAX202E-MAX241E datasheet, the devices use integrated charge-pump circuitry for single +5 V operation. This combination is intended for conventional RS-232 links rather than modern differential serial interfaces.
How much ESD protection does the MAX202EEUE+ provide?
The MAX202EEUE+ provides high ±15 kV human-body-model ESD protection. The Analog Devices MAX202E-MAX241E datasheet describes this protection as part of a family designed for RS-232 and V.28 communications in harsh environments. It does not eliminate the need for sensible connector grounding, cable design, and system-level surge protection.
When should I choose MAX202EEUE+ for an RS-232 interface?
Choose the MAX202EEUE+ when the design needs two full-duplex RS-232 channels from a single 5 V rail and benefits from integrated charge-pump and ±15 kV HBM protection. It is appropriate for legacy equipment, industrial control ports, and instrument links operating up to 120 kbps. It is not the proper choice when the specification requires RS-485, RS-422, or a multidrop bus.
Is the MAX202EEUE+ suitable for industrial equipment?
The MAX202EEUE+ can be used in industrial RS-232 equipment when the operating-temperature and qualification requirements of the assembled product are met. Its ±15 kV HBM protection and EIA/TIA-232E and CCITT V.28 compliance support robust short-distance point-to-point links. Confirm the exact temperature range and lifecycle status in the Analog Devices product documentation before release.
What is the difference between MAX202EEUE+ and MAX202EUE?
The MAX202EEUE+ and MAX202EUE identify closely related catalog entries in the MAX202E family, but ordering-code differences can reflect packaging, grade, or marking conventions. Both appear with a 16-pin TSSOP interface configuration in distributor records. Confirm the manufacturer ordering table, temperature grade, reel form, and full suffix before treating one as a drop-in procurement substitute.
Can MAX202EEUE+ replace MAX202ECUE+T?
The MAX202EEUE+ can be considered for MAX202ECUE+T substitution because both catalog entries use a 16-pin TSSOP configuration and the same MAX202E RS-232 family. The replacement decision still requires checking temperature grade, packing form, and exact suffix decoding. Board compatibility alone does not guarantee equivalent qualification or procurement form.
What can replace the MAX202EEUE+?
The closest documented drop-in choices are MAX202EUE, MAX202EUE+, and MAX202ECUE+T, all appearing in 16-pin TSSOP RS-232 catalog entries. Each should be checked for suffix, temperature grade, and packaging details before substitution. The manufacturer MAX202E family remains the safest option when exact legacy behavior and qualification must be preserved.
What is the best Analog Devices equivalent for MAX202EEUE+?
The MAX202EUE and MAX202EUE+ catalog entries are the closest Analog Devices alternatives because they use the same 16-pin TSSOP RS-232 device family and preserve the two-driver, two-receiver architecture. MAX202ECUE+T is another same-package family option. Verify ordering information and operating-grade requirements before approving a replacement.
Where can I buy MAX202EEUE+ online?
Use the Request a Quote form on this page to request MAX202EEUE+ availability, current commercial terms, and lead time. The form avoids static pricing that can become outdated and connects the request directly with XAIPART. Provide the required quantity, package form, and any date-sensitive production requirements in the request.
What is the price of MAX202EEUE+?
Use the Request a Quote form on this page for the current MAX202EEUE+ unit price and quantity terms. Commercial pricing can vary with order quantity, packaging form, market conditions, and supply status, so a static price should not be copied into a design quotation. The request form is the appropriate route for a current, order-specific response.
What is the lead time and stock status for MAX202EEUE+?
Request current MAX202EEUE+ stock status, minimum order quantity, and lead time through the Request a Quote form on this page. Availability can vary with the exact ordering suffix, reel or tube requirement, order quantity, and production schedule. Include your required delivery date so the commercial response reflects the actual build plan.

Data referensi kejuruteraan untuk MAX202EEUE+ — perbandingan, panduan rancangan, dan maklumat kesediaan

Panduan Pilihan

Choose the MAX202EEUE+ for a 5 V RS-232 design requiring two full-duplex channels, data rates up to 120 kbps, and ±15 kV HBM protection in a 16-pin TSSOP package. Its integrated charge pump simplifies single-rail power design, while two drivers and two receivers support command, status, or diagnostic links. MAX202EUE and MAX202EUE+ are closely related catalog choices in the same package and family, but the complete ordering suffix must be checked for grade and packing details. MAX202ECUE+T is also a package-compatible family option and should be selected only after confirming its temperature grade and procurement form. None of these alternatives is appropriate for a requirement that actually specifies RS-485, RS-422, a multidrop bus, or a higher-speed interface. For exposed industrial cables, assess the broader grounding and surge-protection design rather than relying only on the IC-level ESD rating.

Perbandingan dengan Gantian

Parametr Produk Ini MAX202EUE MAX202EUE+ MAX202ECUE+T
Brand Analog Devices Analog Devices Analog Devices Analog Devices
Package TSSOP-16 TSSOP-16 TSSOP-16 TSSOP-16
Product Type Dual RS-232 transceiver Dual RS-232 transceiver Dual RS-232 transceiver Dual RS-232 transceiver
Number of Drivers 2 2 2 2
Number of Receivers 2 2 2 2
Supply Voltage 5 V 5 V 5 V 5 V
Maximum Data Rate 120 kbps 120 kbps 120 kbps 120 kbps
ESD Protection ±15 kV HBM ±15 kV HBM ±15 kV HBM ±15 kV HBM
Duplex Full duplex Full duplex Full duplex Full duplex
Charge Pump Integrated Integrated Integrated Integrated
Interface Standards EIA/TIA-232E and CCITT V.28 EIA/TIA-232E and CCITT V.28 EIA/TIA-232E and CCITT V.28 EIA/TIA-232E and CCITT V.28

Penyeberangsung Jelas

  • Integrated dual-channel interface in one TSSOP package (vsMAX202EUE)
  • Direct 5 V single-supply RS-232 operation (vsMAX202EUE+)
  • High connector-side ESD resilience (vsMAX202ECUE+T)

Catatan Desain

Place the charge-pump capacitors and supply bypass capacitors close to their associated MAX202EEUE+ pins, following the manufacturer datasheet layout and capacitor values. Keep the high-current driver return path compact and connect the device ground directly to the interface ground reference. Avoid routing RS-232 driver traces across long distances beneath unrelated digital circuitry, where switching currents could increase radiated or coupled noise.

Do not treat MAX202EEUE+ as an RS-485 or RS-422 interface. Its RS-232 architecture uses unbalanced signaling and is intended primarily for point-to-point communication. Verify driver-output and receiver-input direction, connector numbering, and logic polarity before PCB population. Reversing an RS-232 signal path can damage the interface even when the package and supply voltage are correct.

At exposed cable connectors, combine the device's ±15 kV HBM protection with sound mechanical and grounding practices. Keep exposed interface traces away from clocks, switching supplies, and high-impedance analog inputs. Use a low-inductance ground return and consider external surge protection when connected cables extend beyond a controlled equipment enclosure or may carry industrial transients.

Preserve the manufacturer pin numbering and package orientation when using any MAX202E catalog alternative in a TSSOP-16 design. The EUE ordering codes can differ in grade or packing interpretation, so review the complete ordering table before substitution. Check that any replacement remains a 5 V, two-driver, two-receiver RS-232 device with the required ESD rating and operating-temperature range.

Maklumat Kesediaan

RoHS
Unknown
REACH
Unknown
AEC-Q100
Unknown
Bosong logam timbal
Unknown
Bosong halogen
Unknown
Mineral konflik
Unknown

The manufacturer family datasheet confirms RS-232, EIA/TIA-232E, CCITT V.28, ESD-protection, supply, and data-rate characteristics, but explicit RoHS, REACH, AEC-Q100, lead-free, halogen-free, and conflict-minerals declarations were not identified for the exact ordering code.

Data disahkan pada: 2026-11-13 — data yang disahkan dan disusun semula oleh pasukan kejuruteraan komponen XAIPART

Pencarian Berhubungan

MAX202EEUE+ datasheet MAX202EEUE+ pinout MAX202EEUE+ datasheet pdf MAX202EEUE+ equivalent MAX202EEUE+ replacement MAX202EEUE+ cross reference MAX202EEUE+ price MAX202EEUE+ stock Analog Devices MAX202EEUE+ MAX202EEUE+ TSSOP-16 MAX202EEUE+ 120kbps RS-232 MAX202EEUE+ industrial instrument MAX202EEUE+ vs MAX202EUE MAX202EEUE+ footprint

Komponen dan Tanda berkaitan

Analog Devices Maxim Integrated MAX202EEUE+ MAX202EUE MAX202EUE+ MAX202ECUE+T RS-232 transceiver interface IC line driver line receiver full duplex EIA/TIA-232E CCITT V.28 120 kbps 5 V power supply integrated charge pump ±15 kV HBM ESD protection TSSOP-16 TSSOP package family surface mount industrial communication legacy serial port service and diagnostic port RoHS REACH
RFRC Saring Pantas
Isikan butiran lengkap — pasukan jualan kami akan bertindak balas dalam masa 24 jam
Nombor Bahagian Pengeluar Pakej QTY Harga Target Lengkap
✓
Pesan diskon sudah disubmit!

Kami akan bertindak balas kepada emel anda dalam tempoh 24 jam

1
RFQ Diserahkan
2
kutipan Diterima
3
Order Dipesan
4
Pembayaran
5
Dihantar
6
Diantar
Lihat Perincian RFQ