Analog Devices

MAX232AEUE+T 5V RS-232 Transceiver | Analog Devices

MPN: MAX232AEUE+T ✓ فعال
+5 V Vdss 16-pin TSSOP Package
MOQ: 1 |

MAX232AEUE+T جائزہ

Analog Devices MAX232AEUE+T is a +5 V-powered, dual transmitter/receiver RS-232 interface IC packaged in a 16-pin TSSOP. It provides two full-duplex RS-232 driver channels and two receiver channels for translating between TTL/CMOS logic levels and balanced, bipolar RS-232 signals. The device is intended for EIA/TIA-232E, V.28, and V.24 communications interfaces where +12 V and -12 V supplies are unavailable.

An RS-232 transceiver is an interface IC that bridges digital logic and a serial communications port. The transmitter converts TTL/CMOS signals into RS-232 levels, while the receiver converts RS-232 inputs into logic-compatible signals. In the broader device hierarchy, the MAX232AEUE+T belongs to the line-driver/receiver class, interface IC family, and semiconductor category used to connect a UART or other digital controller to an RS-232 port.

The MAX232AEUE+T is identified as a 2/2 full-RS-232 transceiver, meaning that it contains two driver outputs and two receiver inputs. Its +5 V supply operation allows implementation around conventional 5 V digital systems. The MAX232A family is listed in production, and the 16-pin TSSOP package is approximately 4.40 mm wide. Its dual-channel arrangement is useful where two serial ports must share a compact board footprint.

The manufacturer describes the MAX220 through MAX249 family as supporting EIA/TIA-232E and V.28/V.24 interfaces, especially where positive and negative 12 V rails are not available. The MAX232A therefore concentrates the RS-232 electrical layer beneath an existing UART or microprocessor serial interface. Exact slew rate, propagation delay, receiver thresholds, and charge-pump capacitor requirements should be confirmed in the MAX232A data sheet before a new circuit is released.

Typical uses include industrial serial adapters, laboratory instrument interfaces, configuration ports, embedded equipment links, and legacy computer peripherals. The two transmitters and two receivers permit full-duplex communication on each RS-232 channel. Board-level design must preserve the required charge-pump capacitors, logic-side supply decoupling, and clearances between logic and high-voltage RS-232 nets.

Keep input and output transceivers close to their associated connector or signal source, and route differential RS-232 traces away from sensitive clocks and analog signals. Confirm the package pin numbering against the MAX232A data sheet before assigning PCB nets. The narrow TSSOP body also requires careful assembly planning because its lead pitch and body width leave limited routing space.

This page organizes the verified MAX232A family information, exact MAX232AEUE+T package identification, sourcing details, interface standards, and replacement considerations into an engineering-focused reference. It also distinguishes the directly documented device from related family members whose package, channel count, or electrical details differ.

کے لیے ڈراپ اِن متبادل MAX232AEUE+T — یکساں پیکیج، پن سے پن مطابقت پذیر۔ مختلف پیکیج والے پرزے جن کے لیے PCB دوبارہ کام درکار ہو، شامل نہیں ہیں۔

اس سیریز میں مختلف ورژن

اسی سیریز کے ماڈلز جو ڈراپ اِن مطابقت رکھتے ہیں MAX232AEUE+T (یکساں فارم فیکٹر اور فٹ پرنٹ) — میں مختلف Interface Standard, Number of Receivers.

Analog Devices
Interface Standard: Full RS-232
Number of Receivers: 2 receivers
موازنہ کریں MAX232AEUE+T →

MAX232AEUP+T

✅ ڈراپ-اِن ⚠️ تفصیلات غیر تصدیق شدہ
📦 16-pin TSSOP
Same MAX232A 2/2 RS-232 architecture and 16-pin TSSOP footprint; ordering-code qualification and temperature/finish details must be confirmed in the manufacturer ordering table.

📋 حوالہ جاتی متبادل (کیٹلاگ میں نہیں)

MAX232AEUA+T

✅ ڈراپ-اِن ⚠️ تفصیلات غیر تصدیق شدہ
📦 16-pin TSSOP
Same MAX232A 2/2 RS-232 architecture and 16-pin TSSOP footprint; exact temperature and lead-finish ordering attributes may differ by 0-10%.

📋 حوالہ جاتی متبادل (کیٹلاگ میں نہیں)

MAX232AEUE+T تفصیلات

Product Type RS-232 dual transmitter/receiver interface IC
سپلائی وولٹیج +5 V
Number of Transmitters 2 channels
Number of Receivers 2 channels
Interface Standard EIA/TIA-232E, V.28, and V.24
پیکیج 16-pin TSSOP
Package Width 4.40 mm
Package Width (Imperial) 0.173 inch
ماؤنٹنگ ٹائپ Surface mount
Production Status Production
Driver Output Type Full RS-232

MAX232AEUE+T 0.173 inch پن کنفیگریشن گائیڈ

MAX232AEUE+T (0.173 inch پیکیج) کے لیے پن کنفیگریشن۔ پن نمبرنگ، فنکشنز اور کنکشن ڈایاگرامز مینوفیکچرر کے ڈیٹا شیٹ میں بیان کیے گئے ہیں۔ درست فٹ پرنٹ اور سولڈرنگ رہنما ہدایات کے لیے اسی سے رجوع کریں۔

MAX232AEUE+T کے لیے 0.173 inch پیکیج پن آؤٹ ڈایاگرام

کے لیے تفصیلی پن آؤٹ ڈیٹا دستیاب نہیں MAX232AEUE+T.

رجوع کریں ڈیٹا شیٹ مکمل پن کنفیگریشن کے لیے۔

عام استعمالات

MAX232AEUE+T کے لیے موزوں ہے 6 ایپلیکیشنs: Industrial Serial Adapter, Laboratory Instrument Control Port, Embedded Configuration Interface, Legacy Computer Peripheral, Point-to-Point Communication Link, Data Acquisition Equipment.

🏭

Industrial Serial Adapter

The MAX232AEUE+T is suitable for an industrial serial adapter that converts a 5 V controller UART into an EIA/TIA-232E-compatible port. Its two transmitters and two receivers allow two bidirectional RS-232 channels to share one compact 16-pin TSSOP. The device eliminates the need for positive and negative 12 V interface rails, although the charge-pump capacitors and bypass capacitor still require correct placement. For an enclosure-mounted adapter, keep the RS-232 traces away from switching supplies and route the driver outputs toward the connector with minimal loop area. The dual-channel arrangement is especially useful when equipment must expose both a primary control port and a secondary service or diagnostic port.

🔧

Laboratory Instrument Control Port

The MAX232AEUE+T can provide the physical RS-232 layer for a laboratory instrument controlled by a 5 V embedded controller. Two transmitters and two receivers support separate command and response channels or two instrument buses, while the single +5 V supply simplifies integration with digital logic. Maintain a clean separation between logic-side traces and the bipolar RS-232 side, and verify the data sheet's charge-pump capacitor values and receiver thresholds during schematic review. This arrangement reduces the number of external level-shifting rails compared with a discrete ±12 V driver implementation.

🖥️

Embedded Configuration Interface

The MAX232AEUE+T fits an embedded configuration port where a service technician connects a computer or terminal to equipment that otherwise operates from +5 V. Its two full-duplex channels can carry a primary configuration link and an auxiliary diagnostic link, and the 16-pin TSSOP preserves board area in compact control systems. The UART or processor must be configured for the interface's electrical conventions, and the board should include the manufacturer-required charge-pump capacitors close to the device. Use a protected connector or enclosure arrangement when the port will be accessible in uncontrolled environments.

💻

Legacy Computer Peripheral

The MAX232AEUE+T is appropriate for a legacy computer peripheral that exposes an RS-232 port from a +5 V controller. Because the MAX232A family supports EIA/TIA-232E, V.28, and V.24 communications interfaces, it can bridge a modern digital controller to established RS-232 equipment without separate positive and negative 12 V rails. The 2/2 channel count can serve two peripheral connections if the wiring plan allows it. Confirm connector pin assignment, ground continuity, and software flow control because the transceiver solves voltage translation, not protocol or cable-direction issues.

🌐

Point-to-Point Communication Link

The MAX232AEUE+T can establish two point-to-point RS-232 links between two +5 V systems. Each transmitter drives one receiver, creating full-duplex communication when the transmit and receive conductors are paired correctly. This is useful in equipment racks, test fixtures, and short industrial links where a multi-drop RS-485 bus would be inappropriate. The driver and receiver stages perform only the electrical interface, so cable length, ground reference, and protocol timing remain separate design constraints. Confirm the MAX232A electrical limits and connector protection requirements before deploying long or noisy interconnects.

📊

Data Acquisition Equipment

The MAX232AEUE+T can serve as the RS-232 interface for data-acquisition equipment that uses a 5 V control plane while connecting to a host computer or service terminal. The two receiver channels can accept status or command information, and the two transmitter channels can carry responses or sampled data. Its narrow 16-pin TSSOP package is useful where connector placement and routing space are constrained. Place the interface away from high-current analog sections, observe the manufacturer's charge-pump capacitor layout, and use controlled grounding to prevent ground currents from coupling into measurement circuitry.

What is the MAX232AEUE+T?
The MAX232AEUE+T is a +5 V-powered, dual transmitter/receiver RS-232 interface IC from Analog Devices. It provides two full-RS-232 transmitter channels and two receiver channels in a 16-pin TSSOP package. According to the MAX232A manufacturer page, the device is intended for EIA/TIA-232E, V.28, and V.24 communications interfaces, particularly where positive and negative 12 V supplies are not available.
What are the key specifications of MAX232AEUE+T that engineers should know?
The MAX232AEUE+T combines two RS-232 transmitters, two receivers, and +5 V operation in a 16-pin TSSOP package. Analog Devices identifies the MAX232A as production and describes it as a multichannel RS-232 driver/receiver family part supporting EIA/TIA-232E, V.28, and V.24. The verified package width is 4.40 mm, or 0.173 inch. Exact data rate, propagation delay, and operating temperature should be taken from the manufacturer data sheet.
Where can I download the MAX232AEUE+T datasheet PDF?
The MAX232AEUE+T data sheet can be obtained through the official MAX232A product page at analog.com/en/products/max232a.html. That page identifies the family as the +5 V-powered MAX232A multichannel RS-232 driver/receiver and provides the manufacturer documentation. The product-page snippet explicitly references Data Sheet Rev. 18, so use the revision linked by the manufacturer and verify its document identifier against the downloaded PDF before releasing a design.
Where can I find the MAX232AEUE+T pinout?
The MAX232AEUE+T pin assignment is found in the pin-description and package diagrams of the official MAX232A data sheet. The exact ordering code uses a 16-pin TSSOP package, approximately 4.40 mm wide. Use the manufacturer diagram to map supply, charge-pump, receiver, driver, and ground pins because the ordering suffix, package code, exposed-pad arrangement, and lead numbering must all be checked against the selected revision.
Is MAX232AEUE+T suitable for a 5 V UART interface?
Yes, the MAX232AEUE+T is designed for +5 V-powered RS-232 interface circuits and can sit between a 5 V UART or digital controller and an RS-232 port. Its two transmitters and two receivers support two bidirectional channels when the corresponding driver and receiver are connected together. The circuit still requires correct charge-pump capacitance, supply decoupling, grounding, and connector-level protection according to the manufacturer application guidance.
How does MAX232AEUE+T differ from MAX3232?
MAX232AEUE+T is a two-transmitter, two-receiver RS-232 interface in a 16-pin TSSOP, while the MAX3232 family uses a different product family with different supply and channel configurations. The MAX3232EUE+T part identified in the MAX3232 family is also associated with a 16-pin TSSOP, but a shared body size alone does not establish pin-to-pin compatibility. Confirm the MAX3232E data sheet pin table and all logic-side requirements before treating it as a direct replacement.
What is the best drop-in replacement for MAX232AEUE+T?
The best replacement is the part that preserves the 16-pin TSSOP footprint, pin functions, 2/2 channel arrangement, +5 V supply architecture, and required charge-pump behavior. MAX232AEUE+ is the same listed electrical configuration but represents the non-tape-and-reel ordering form rather than an engineering alternative. A qualified same-family ordering option can be considered when its package code and temperature grade are confirmed against the manufacturer data sheet; functional RS-232 parts in other packages are not drop-in replacements.
Can MAX232AEUE+T replace MAX3232EUE+T?
Do not assume that MAX232AEUE+T can replace MAX3232EUE+T solely because both are associated with 16-pin TSSOP packages. The MAX232AEUE+T is documented as a 2/2 transmitter/receiver RS-232 device, while the MAX3232E family has a different channel arrangement and device architecture. A valid substitution requires a complete pin-by-pin comparison, including supply pins, receiver enable behavior, driver outputs, charge-pump connections, and package dimensions.
When should I choose MAX232AEUE+T over another 16-pin RS-232 transceiver?
Choose MAX232AEUE+T when the design requires a production +5 V RS-232 transceiver with two transmitters, two receivers, and a 16-pin TSSOP footprint. It is a logical choice for compact dual-port equipment using EIA/TIA-232E, V.28, or V.24 signaling. Select another device only when it offers a necessary voltage, temperature, ESD, channel-count, or data-rate advantage while retaining the same pinout and charge-pump architecture.
Is MAX232AEUE+T in stock?
The current stock status should be requested through the Request a Quote form on this page. The manufacturer lists the MAX232A family in production, while exact assembly, quantity, and delivery availability can vary by ordering code and shipping destination. Submit the complete MPN MAX232AEUE+T, target quantity, and delivery location so the quote can be matched to the correct 16-pin TSSOP configuration.
What is the price of MAX232AEUE+T?
Use the Request a Quote form on this page for current pricing and volume availability for MAX232AEUE+T. The price can depend on order quantity, package, lead time, and fulfillment terms, so it is best not to rely on an unverified historical catalog amount. Include the target quantity and required ship date in the request to obtain a current quotation for the exact ordering code.
What is the lead time for MAX232AEUE+T?
Request the current lead time through the Request a Quote form on this page. Analog Devices lists the MAX232A family in production, but manufacturing capacity, assembly packaging, and distributor schedules can change independently of that lifecycle statement. A reliable delivery commitment requires the requested quantity, ship-to country, and target date, particularly for scheduled production and higher-volume orders.
Where to buy MAX232AEUE+T online?
Use the Request a Quote form on this page to purchase MAX232AEUE+T and confirm current availability, minimum order quantity, and lead time. The form is the appropriate channel because the exact MAX232AEUE+T ordering code, 16-pin TSSOP package, quantity, and delivery conditions should be matched together. This avoids ambiguity with the closely related MAX232AEUE+ tape-and-reel and other MAX232A package variants.
What can replace MAX232AEUE+T?
A replacement for MAX232AEUE+T must be pin-to-pin compatible with the 16-pin TSSOP MAX232AEUE+T footprint and preserve its two-driver, two-receiver RS-232 functions. The closest same-family ordering option is the equivalent ordering form selected after checking the package and temperature codes, but packaging-only variants are not distinct engineering alternatives. Other manufacturers should be accepted only when a manufacturer cross-reference explicitly identifies pin-to-pin compatibility.
Is MAX232AEUE+T the same as MAX232AEUE+?
MAX232AEUE+T and MAX232AEUE+ identify the same MAX232AEUE device family, but the ordering codes indicate different delivery packaging: the +T form is associated with tape-and-reel handling. Both are listed as 2/2 full-RS-232 transceivers in a 16-pin TSSOP. For PCB assembly and purchasing, treat MAX232AEUE+T as the exact requested MPN and verify its package markings rather than treating it as a different electrical design.

کے لیے انجینئرنگ ریفرنس ڈیٹا MAX232AEUE+T — موازنہ، ڈیزائن رہنمائی، اور تعمیل کی معلومات۔

انتخاب کی گائیڈ

Choose MAX232AEUE+T for a compact +5 V equipment design that needs two RS-232 transmit channels and two receive channels in a 16-pin TSSOP. It is particularly appropriate for EIA/TIA-232E, V.28, and V.24 point-to-point interfaces where positive and negative 12 V rails are undesirable. MAX232AEUP+T and MAX232AEUA+T are same-brand ordering candidates for footprint reuse, but their exact ordering attributes and temperature limits must be confirmed before substitution. Do not select a MAX3232, MAX202, or another RS-232 interface solely because it has a similar body size; a valid drop-in alternative must preserve the pin functions, charge-pump architecture, supply arrangement, channel count, and electrical limits. For new designs with different channel counts, lower-voltage operation, stronger ESD requirements, or a different package, perform a full data-sheet comparison rather than forcing a MAX232A replacement.

متبادلات کے ساتھ موازنہ

پیرامیٹر یہ پروڈکٹ MAX232AEUP+T MAX232AEUA+T
Brand Analog Devices Analog Devices Analog Devices
Package 16-pin TSSOP 16-pin TSSOP 16-pin TSSOP
Transmitter Count 2 channels 2 channels 2 channels
Receiver Count 2 channels 2 channels 2 channels
Supply Voltage +5 V +5 V +5 V
Supported Interface Standards EIA/TIA-232E, V.28, and V.24 EIA/TIA-232E, V.28, and V.24 EIA/TIA-232E, V.28, and V.24
Driver Type Full RS-232 Full RS-232 Full RS-232
Package Width 4.40 mm (0.173 inch) 4.40 mm (0.173 inch) 4.40 mm (0.173 inch)

اہم امتیازی خصوصیات

  • Combines two transmit and two receive channels in one interface device (بمقابلہMAX232AEUP+T)
  • Uses a single +5 V supply architecture (بمقابلہMAX232AEUA+T)
  • Targets established point-to-point RS-232 standards (بمقابلہMAX232AEUP+T)

ڈیزائن نوٹس

Place the charge-pump capacitors directly beside their designated MAX232AEUE+T pins and keep their return paths short, as specified in the manufacturer application circuit. Place the logic-side bypass capacitor close to the +5 V supply pin. Keep the footprint orientation consistent with the package drawing, because the 16-pin TSSOP body is narrow and incorrect pad placement can create assembly or soldering problems.

Separate logic-side nets from RS-232 driver outputs on the PCB. Route driver outputs toward the connector with a short path and avoid routing them beneath sensitive analog sections. Connect the logic and interface grounds using the topology shown in the manufacturer reference circuit, and verify connector shield and chassis-ground treatment separately from the circuit ground.

Do not treat the MAX232AEUE+T as an RS-485 transceiver or as a replacement for a transceiver with a different channel arrangement. Confirm the complete 16-pin mapping, required capacitor values, receiver enable states, and supported temperature range against the manufacturer data sheet. Also distinguish MAX232AEUE+T from packaging-only ordering forms before releasing the BOM or placing a footprint.

تعمیل کی معلومات

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
لیڈ فری
Unknown
ہیلوجن فری
Unknown
کنفلیکٹ منرلز
Unknown

The verified product information identifies MAX232A as a production RS-232 interface family but does not provide specific RoHS, REACH, lead-free, halogen-free, or conflict-minerals declarations for MAX232AEUE+T.

ڈیٹا کی تصدیق کی تاریخ: 2026-11-17 — ڈیٹا XAIPART کی کمپوننٹ انجینئرنگ ٹیم کے ذریعے تصدیق شدہ اور ترتیب شدہ

متعلقہ تلاشیں

MAX232AEUE+T datasheet MAX232AEUE+T pinout MAX232AEUE+T datasheet pdf MAX232AEUE+T equivalent MAX232AEUE+T replacement MAX232AEUE+T cross reference MAX232AEUE+T footprint MAX232AEUE+T price MAX232AEUE+T stock Analog Devices MAX232AEUE+T MAX232AEUE 16-TSSOP MAX232AEUE RS-232 interface MAX232AEUE vs MAX232AEUP+T

متعلقہ اجزاء اور اصطلاحات

Analog Devices MAX232AEUE+T MAX232AEUP+T MAX232AEUA+T MAX232A RS-232 RS-232 transceiver line driver line receiver interface IC semiconductor EIA/TIA-232E V.28 V.24 TSSOP-16 surface mount SMD UART charge-pump capacitor full-duplex communication +5 V supply industrial serial adapter data acquisition equipment legacy computer peripheral
فوری کوٹ RFQ
مکمل تفصیلات بھریں — ہماری سیلز ٹیم 24 گھنٹوں میں جواب دے گی
پارٹ نمبر مینوفیکچرر پیکج QTY ہدف قیمت کل رقم
✓
کوٹ جمع ہو گیا!

ہم 24 گھنٹوں کے اندر آپ کے ای میل کا جواب دیں گے

1
RFQ جمع ہو گیا
2
کوٹ موصول ہو گیا
3
آرڈر دے دیا گیا
4
ادائیگی
5
بھیج دیا گیا
6
ڈیلیور شدہ
RFQ تفصیلات دیکھیں