MAX3232CDWRG4 - Dual 250kbps RS-232 Transceiver | Texas Instruments
MPN: MAX3232CDWRG4 ✓ فعالMAX3232CDWRG4 جائزہ
An RS-232 transceiver is an interface IC that converts low-voltage digital logic signals into RS-232 voltage levels and converts incoming RS-232 levels back into logic-compatible signals. Within the electronics hierarchy, the MAX3232 belongs to the interface IC family, where line drivers and receivers bridge computer or embedded-system logic with a differential, bipolar signaling interface. It is designed for point-to-point serial links where the full RS-232 voltage range, noise tolerance, and ESD resilience are more important than low-voltage logic-only communication.
The MAX3232 family supports 3 V and 5 V supply operation, allowing use with modern 3.3 V systems as well as conventional 5 V equipment. Its maximum signaling rate of 250 kbps supports data-transfer rates commonly required by serial console, instrumentation, and industrial-control interfaces. The integrated charge pump generates the positive and negative voltages required by RS-232 transmitters without a separate negative supply, while ±15 kV human-body-model ESD protection improves robustness at externally accessible connector pins.
The receiver section uses approximately 300 mV of hysteresis to distinguish valid logic states in the presence of noise. This threshold helps prevent repeated transitions near the signal threshold, which can otherwise cause corrupted characters or erratic framing. The two-channel arrangement provides one full-duplex path per channel, allowing simultaneous transmission and reception on each RS-232 link when the connected equipment and protocol support that direction of traffic.
Typical uses include industrial serial consoles, test and measurement equipment, point-of-sale terminals, data-acquisition systems, and embedded-control boards. The device is particularly appropriate where equipment uses DB9 or equivalent RS-232 connectors and needs a compact interface solution operating from a single 3 V or 5 V rail. Its ±15 kV ESD rating is especially relevant where the serial cable leaves an enclosure or connects to user-accessible equipment.
Designers should follow the manufacturer datasheet for the exact charge-pump capacitor values, driver and receiver pin assignments, and recommended layout. Keep the external capacitor connections short, provide a stable supply-decoupling path, and route the driver outputs toward the connector while separating them from sensitive receiver inputs. Do not treat ±15 kV ESD protection as a substitute for enclosure grounding, cable shielding, or external surge protection.
This product page combines the manufacturer's electrical specifications with an application-focused comparison of temperature grades, package compatibility, interface alternatives, and practical PCB considerations. It also distinguishes direct replacement options from broader RS-232 transceiver families, helping engineers confirm footprint, logic-level, speed, and protection requirements before approving a substitution.
کے لیے ڈراپ اِن متبادل MAX3232CDWRG4 — یکساں پیکیج، پن سے پن مطابقت پذیر۔ مختلف پیکیج والے پرزے جن کے لیے PCB دوبارہ کام درکار ہو، شامل نہیں ہیں۔
اس سیریز میں مختلف ورژن
اسی سیریز کے ماڈلز جو ڈراپ اِن مطابقت رکھتے ہیں MAX3232CDWRG4 (یکساں فارم فیکٹر اور فٹ پرنٹ) — میں مختلف Package, Supply Voltage Range, ESD Protection, Maximum Data Rate, Number of Drivers.
MAX3232EIDR
✅ ڈراپ-اِنقیمت کے لیے رابطہ کریں
ڈیٹا شیٹ دیکھیں →MAX3232EIPWG4
✅ ڈراپ-اِن ⚠️ تفصیلات غیر تصدیق شدہقیمت کے لیے رابطہ کریں
ڈیٹا شیٹ دیکھیں →MAX3232IPW
✅ ڈراپ-اِن ⚠️ تفصیلات غیر تصدیق شدہقیمت کے لیے رابطہ کریں
ڈیٹا شیٹ دیکھیں →MAX3232CDR
✅ ڈراپ-اِن📋 حوالہ جاتی متبادل (کیٹلاگ میں نہیں)
MAX3232EIPWG4
✅ ڈراپ-اِنقیمت کے لیے رابطہ کریں
ڈیٹا شیٹ دیکھیں →MAX3232CDWRG4 تفصیلات
| Product Type | Dual RS-232 line driver and receiver |
| Number of Channels | 2 transmitter and 2 receiver channels |
| Supply Voltage Range | 3 V to 5.5 V |
| Maximum Data Rate | 250 kbps |
| ESD Protection | ±15 kV HBM |
| Receiver Hysteresis | 300 mV |
| آپریٹنگ درجہ حرارت رینج | 0°C to 70°C |
| Maximum Supply Current | 1 mA |
| پیکیج | 16-pin SOIC |
| Terminal Count | 16 terminals |
| ماؤنٹنگ اسٹائل | Surface mount |
| Package Shape | Rectangular |
| Lead Form | Gull wing |
| Interface Standard | RS-232 |
| Temperature Grade | Commercial |
MAX3232CDWRG4 rectangular پن کنفیگریشن گائیڈ
MAX3232CDWRG4 (rectangular پیکیج) کے لیے پن کنفیگریشن۔ پن نمبرنگ، فنکشنز اور کنکشن ڈایاگرامز مینوفیکچرر کے ڈیٹا شیٹ میں بیان کیے گئے ہیں۔ درست فٹ پرنٹ اور سولڈرنگ رہنما ہدایات کے لیے اسی سے رجوع کریں۔
کے لیے تفصیلی پن آؤٹ ڈیٹا دستیاب نہیں MAX3232CDWRG4.
رجوع کریں ڈیٹا شیٹ مکمل پن کنفیگریشن کے لیے۔
عام استعمالات
MAX3232CDWRG4 کے لیے موزوں ہے 6 ایپلیکیشنs: Industrial Serial Console Interface, Data Acquisition and Test Equipment, Point-of-Sale and Peripheral Connectivity, Embedded Controller Serial Port, RS-232 Equipment-to-Equipment Link, External Cable-Facing Interface Card.
Industrial Serial Console Interface
The MAX3232CDWRG4 fits an industrial serial console that requires a single 3.3 V or 5 V supply and RS-232 levels for a service connector. Its 250 kbps maximum data rate accommodates common console baud rates, while the dual-driver, dual-receiver arrangement supports one full-duplex link in a 16-pin SOIC. The 300 mV receiver hysteresis improves tolerance of transitions near the logic threshold, and ±15 kV HBM ESD protection is valuable where a service cable crosses an enclosure boundary. The commercial 0°C to 70°C rating should be checked against the enclosure's maximum internal ambient temperature.
تجویز کردہ
Data Acquisition and Test Equipment
For data-acquisition and test equipment, the MAX3232CDWRG4 can bridge a controller to an RS-232 instrument without requiring a negative external supply. Its integrated charge pump produces the bipolar signal levels expected by the RS-232 interface, while operation from 3 V to 5.5 V simplifies compatibility with embedded controllers and legacy instrumentation. Signaling up to 250 kbps supports reliable command and response traffic, and the receiver hysteresis of approximately 300 mV helps reject noise. Place the charge-pump capacitors close to their pins and maintain a low-impedance supply path.
تجویز کردہ
Point-of-Sale and Peripheral Connectivity
The MAX3232CDWRG4 is appropriate for point-of-sale equipment, service terminals, and peripherals that use a conventional RS-232 port. A 16-pin SOIC preserves a compact board footprint, and the 3 V to 5.5 V supply range supports embedded systems with either 3.3 V or 5 V rails. Two transmit and two receive channels provide flexible point-to-point links without requiring separate single-direction transceiver ICs. Its ±15 kV HBM ESD rating improves connector-interface robustness, but the enclosure and cable still require appropriate grounding and shielding practices.
تجویز کردہ
Embedded Controller Serial Port
An embedded controller with a UART can use the MAX3232CDWRG4 to add a standard RS-232 port while the controller operates at a lower logic voltage. The interface IC translates between CMOS or TTL-compatible receiver outputs and the bipolar RS-232 driver outputs, while its integrated charge pump removes the need for a negative system supply. The 250 kbps capability is suitable for many configuration, logging, and command protocols. Confirm logic thresholds, baud-rate tolerance, and pin assignments in the manufacturer datasheet before final PCB routing.
تجویز کردہ
RS-232 Equipment-to-Equipment Link
The MAX3232CDWRG4 supports equipment-to-equipment RS-232 links where a point-to-point serial connection is more reliable than a longer protocol-specific interface. Its 250 kbps limit accommodates many configuration and control links, and the approximately 300 mV receiver hysteresis provides a degree of noise immunity in industrial environments. The commercial temperature range of 0°C to 70°C covers typical indoor equipment. Verify the cable length, ground reference, connector pin assignment, and whether the linked devices require hardware handshaking before installation.
تجویز کردہ
External Cable-Facing Interface Card
A cable-facing interface card can use the MAX3232CDWRG4 to provide RS-232 connectivity behind an enclosure opening. The ±15 kV HBM ESD rating on the bus terminals is particularly relevant when users connect and disconnect external cables. Its integrated 3 V to 5.5 V operation reduces external power requirements, and the 16-pin SOIC is suitable for compact embedded boards. The IC protection rating should be treated as one layer of the design: use chassis grounding, cable shielding, connector design, and any required surge protection according to the installation environment.
تجویز کردہ
تجویز کردہ پروڈکٹس کا خلاصہ
کے لیے انجینئرنگ ریفرنس ڈیٹا MAX3232CDWRG4 — موازنہ، ڈیزائن رہنمائی، اور تعمیل کی معلومات۔
انتخاب کی گائیڈ
متبادلات کے ساتھ موازنہ
| پیرامیٹر | یہ پروڈکٹ | MAX3232EIDR | MAX3232EIPW | MAX3232IPW | MAX3232CDR | MAX3232E |
|---|---|---|---|---|---|---|
| Package | 16-SOIC wide body | 16-SOIC | 16-SOIC | 16-SOIC | 16-SOIC narrow body | 16-SOIC |
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Channel Configuration | 2 driver and 2 receiver channels | 2 driver and 2 receiver channels | 2 driver and 2 receiver channels | 2 driver and 2 receiver channels | 2 driver and 2 receiver channels | 2 driver and 2 receiver channels |
| Supply Voltage Range | 3 V to 5.5 V | 3 V to 5.5 V | 3 V to 5.5 V | 3 V to 5.5 V | 3 V to 5.5 V | 3 V to 5.5 V |
| Maximum Data Rate | 250 kbps | 250 kbps | 250 kbps | 250 kbps | 250 kbps | 250 kbps |
| ESD Protection | ±15 kV HBM | ±15 kV HBM | ±15 kV HBM | ±15 kV HBM | ±15 kV HBM | ±15 kV HBM |
| Temperature Grade | Commercial, 0°C to 70°C | Industrial, -40°C to 85°C | Industrial, -40°C to 85°C | Extended temperature | Commercial, 0°C to 70°C | Selectable by package suffix |
| Receiver Hysteresis | 300 mV | 300 mV | 300 mV | 300 mV | 300 mV | 300 mV |
اہم امتیازی خصوصیات
- Improved same-family replacement option (بمقابلہMAX3232EIDR)
- Compact two-channel interface (بمقابلہMAX3232CDR)
- Single-rail bipolar voltage generation (بمقابلہMAX3232IPW)
- Connector-facing ESD resilience (بمقابلہMAX3232E)
ڈیزائن نوٹس
Place the MAX3232 charge-pump capacitors directly between the capacitor pins and the nearest available ground plane, with the shortest possible traces. Keep the supply bypass capacitor adjacent to VCC and ground pins, and provide an uninterrupted ground reference beneath the device. Because the circuit develops bipolar RS-232 voltage internally, follow the manufacturer layout drawing exactly rather than treating the charge-pump section as an ordinary low-current logic block.
Route each RS-232 driver output directly toward its connector, keep receiver inputs away from those outputs, and avoid placing long parallel traces beneath the transceiver. Where a board supports both RS-232 and another high-energy interface, maintain separation to reduce differential crosstalk. Connect the signal ground according to the system grounding strategy and use a dedicated connector-side return path when long or externally accessible cables are involved.
Do not substitute every 16-pin SOIC RS-232 device solely because the package pin count matches. Verify the SOIC body width and lead pitch, the number and arrangement of driver and receiver pins, charge-pump capacitor connections, supply limits, maximum data rate, and temperature grade. MAX3232CDR, for example, is a narrow-body 16-pin SOIC and may not match the land pattern of the wide-body MAX3232CDWRG4 even though both use the same family name.
The MAX3232 generates the bipolar voltages required by RS-232 through an internal charge pump, so supply and ground return paths can carry high-frequency ripple even though the data rate is only 250 kbps. Decouple the supply close to the IC, maintain a compact ground return for charge-pump current, and avoid routing sensitive analog or high-speed digital traces beneath the switched-capacitor section. ESD protection helps at the connector but does not eliminate the need for shielding and correct grounding.
تعمیل کی معلومات
The manufacturer documentation identifies a commercial-temperature RS-232 interface IC, but explicit RoHS, REACH, lead-free, halogen-free, conflict-minerals, and automotive qualification statements were not identified for the exact orderable MPN.