Texas Instruments

MAX3232CDWRG4 - Dual 250kbps RS-232 Transceiver | Texas Instruments

MPN: MAX3232CDWRG4 ✓ Hoạt động
3 V to 5.5 V Vdss 1 mA Id 16-pin SOIC Package
MOQ: 1 |

MAX3232CDWRG4 Tóm tắt

The Texas Instruments MAX3232CDWRG4 is a dual-channel RS-232 line driver and receiver operating from 3 V to 5.5 V at data rates up to 250 kbps, with ±15 kV ESD protection, in a 16-pin SOIC package. The device combines two RS-232 drivers, two receivers, and an on-chip charge-pump supply in one compact interface circuit. Its commercial temperature grade supports operation from 0°C to 70°C.

An RS-232 transceiver is an interface IC that converts low-voltage digital logic signals into RS-232 voltage levels and converts incoming RS-232 levels back into logic-compatible signals. Within the electronics hierarchy, the MAX3232 belongs to the interface IC family, where line drivers and receivers bridge computer or embedded-system logic with a differential, bipolar signaling interface. It is designed for point-to-point serial links where the full RS-232 voltage range, noise tolerance, and ESD resilience are more important than low-voltage logic-only communication.

The MAX3232 family supports 3 V and 5 V supply operation, allowing use with modern 3.3 V systems as well as conventional 5 V equipment. Its maximum signaling rate of 250 kbps supports data-transfer rates commonly required by serial console, instrumentation, and industrial-control interfaces. The integrated charge pump generates the positive and negative voltages required by RS-232 transmitters without a separate negative supply, while ±15 kV human-body-model ESD protection improves robustness at externally accessible connector pins.

The receiver section uses approximately 300 mV of hysteresis to distinguish valid logic states in the presence of noise. This threshold helps prevent repeated transitions near the signal threshold, which can otherwise cause corrupted characters or erratic framing. The two-channel arrangement provides one full-duplex path per channel, allowing simultaneous transmission and reception on each RS-232 link when the connected equipment and protocol support that direction of traffic.

Typical uses include industrial serial consoles, test and measurement equipment, point-of-sale terminals, data-acquisition systems, and embedded-control boards. The device is particularly appropriate where equipment uses DB9 or equivalent RS-232 connectors and needs a compact interface solution operating from a single 3 V or 5 V rail. Its ±15 kV ESD rating is especially relevant where the serial cable leaves an enclosure or connects to user-accessible equipment.

Designers should follow the manufacturer datasheet for the exact charge-pump capacitor values, driver and receiver pin assignments, and recommended layout. Keep the external capacitor connections short, provide a stable supply-decoupling path, and route the driver outputs toward the connector while separating them from sensitive receiver inputs. Do not treat ±15 kV ESD protection as a substitute for enclosure grounding, cable shielding, or external surge protection.

This product page combines the manufacturer's electrical specifications with an application-focused comparison of temperature grades, package compatibility, interface alternatives, and practical PCB considerations. It also distinguishes direct replacement options from broader RS-232 transceiver families, helping engineers confirm footprint, logic-level, speed, and protection requirements before approving a substitution.

Bộ thay thế dễ dàng lắp đặt cho MAX3232CDWRG4 — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.

Các biến thể trong loạt này

Các mẫu cùng loạt có thể lắp đặt dễ dàng tương thích với MAX3232CDWRG4 (cùng hình factor và footprint) — khác nhau ở Package, Supply Voltage Range, ESD Protection, Maximum Data Rate, Number of Drivers.

Texas Instruments
Package: 16-TSSOP (0.173 in, 4.40 mm width)
Number of Drivers: 2
So sánh với MAX3232CDWRG4 →
Texas Instruments
Package: 16-pin TSSOP
Supply Voltage Range: 3V to 5.5V
ESD Protection: ±15kV
So sánh với MAX3232CDWRG4 →

MAX3232EIDR

✅ Drop-In
Texas Instruments
📦 16-SOIC
Dual RS-232 line driver/receiver transceiver · 2 drivers · 2 receivers · 250 kbps · 3 V to 5.5 V · 3.3 V · RS-232 · ±15 kV

Liên hệ để biết giá

Xem tài liệu →

MAX3232EIPWG4

✅ Drop-In ⚠️ Thông số chưa được xác minh
Texas Instruments
📦 16-SOIC
RS-232 Line Driver/Receiver · 2 · 2 · 3 V to 5.5 V · 250 kbps · +/-15 kV · +/-8 kV · +/-15 kV

Liên hệ để biết giá

Xem tài liệu →

MAX3232IPW

✅ Drop-In ⚠️ Thông số chưa được xác minh
Texas Instruments
📦 16-SOIC
Dual RS-232 line driver and receiver · 2 channels · 2 channels · 3V to 5.5V · 250kbit/s · ±15kV · 5V logic · 0.1µF

Liên hệ để biết giá

Xem tài liệu →

MAX3232CDR

✅ Drop-In
📦 16-SOIC
Matches the dual 250 kbps RS-232 function and 16-pin electrical interface, but uses a narrow SOIC body rather than the wide DW package; PCB land pattern must be checked before substitution.

📋 Tham chiếu thay thế (không có trong danh mục)

MAX3232EIPWG4

✅ Drop-In
Texas Instruments
📦 16-SOIC
RS-232 Line Driver/Receiver · 2 · 2 · 3 V to 5.5 V · 250 kbps · +/-15 kV · +/-8 kV · +/-15 kV

Liên hệ để biết giá

Xem tài liệu →

MAX3232CDWRG4 Thông số kỹ thuật

Product Type Dual RS-232 line driver and receiver
Number of Channels 2 transmitter and 2 receiver channels
Supply Voltage Range 3 V to 5.5 V
Maximum Data Rate 250 kbps
ESD Protection ±15 kV HBM
Receiver Hysteresis 300 mV
Khoảng nhiệt độ hoạt động 0°C to 70°C
Maximum Supply Current 1 mA
Hộp 16-pin SOIC
Terminal Count 16 terminals
Kiểu lắp đặt Surface mount
Package Shape Rectangular
Lead Form Gull wing
Interface Standard RS-232
Temperature Grade Commercial

Hướng dẫn cấu hình chân MAX3232CDWRG4 rectangular

Cấu hình chân cho MAX3232CDWRG4 (rectangular gói). Số thứ tự chân, chức năng và sơ đồ kết nối được xác định trong tài liệu thông số kỹ thuật của nhà sản xuất. Tham khảo nó để biết footprint và hướng dẫn hàn chính xác.

Bảng cấu hình chân rectangular cho MAX3232CDWRG4

Không có dữ liệu chân cụ thể sẵn có cho MAX3232CDWRG4.

Tham khảo: tài liệu kỹ thuật cho cấu hình chân đầy đủ.

Ứng dụng tiêu biểu

MAX3232CDWRG4 phù hợp cho 6 Áp dụngs: Industrial Serial Console Interface, Data Acquisition and Test Equipment, Point-of-Sale and Peripheral Connectivity, Embedded Controller Serial Port, RS-232 Equipment-to-Equipment Link, External Cable-Facing Interface Card.

🏭

Industrial Serial Console Interface

The MAX3232CDWRG4 fits an industrial serial console that requires a single 3.3 V or 5 V supply and RS-232 levels for a service connector. Its 250 kbps maximum data rate accommodates common console baud rates, while the dual-driver, dual-receiver arrangement supports one full-duplex link in a 16-pin SOIC. The 300 mV receiver hysteresis improves tolerance of transitions near the logic threshold, and ±15 kV HBM ESD protection is valuable where a service cable crosses an enclosure boundary. The commercial 0°C to 70°C rating should be checked against the enclosure's maximum internal ambient temperature.

📟

Data Acquisition and Test Equipment

For data-acquisition and test equipment, the MAX3232CDWRG4 can bridge a controller to an RS-232 instrument without requiring a negative external supply. Its integrated charge pump produces the bipolar signal levels expected by the RS-232 interface, while operation from 3 V to 5.5 V simplifies compatibility with embedded controllers and legacy instrumentation. Signaling up to 250 kbps supports reliable command and response traffic, and the receiver hysteresis of approximately 300 mV helps reject noise. Place the charge-pump capacitors close to their pins and maintain a low-impedance supply path.

🖥️

Point-of-Sale and Peripheral Connectivity

The MAX3232CDWRG4 is appropriate for point-of-sale equipment, service terminals, and peripherals that use a conventional RS-232 port. A 16-pin SOIC preserves a compact board footprint, and the 3 V to 5.5 V supply range supports embedded systems with either 3.3 V or 5 V rails. Two transmit and two receive channels provide flexible point-to-point links without requiring separate single-direction transceiver ICs. Its ±15 kV HBM ESD rating improves connector-interface robustness, but the enclosure and cable still require appropriate grounding and shielding practices.

🔧

Embedded Controller Serial Port

An embedded controller with a UART can use the MAX3232CDWRG4 to add a standard RS-232 port while the controller operates at a lower logic voltage. The interface IC translates between CMOS or TTL-compatible receiver outputs and the bipolar RS-232 driver outputs, while its integrated charge pump removes the need for a negative system supply. The 250 kbps capability is suitable for many configuration, logging, and command protocols. Confirm logic thresholds, baud-rate tolerance, and pin assignments in the manufacturer datasheet before final PCB routing.

🌐

RS-232 Equipment-to-Equipment Link

The MAX3232CDWRG4 supports equipment-to-equipment RS-232 links where a point-to-point serial connection is more reliable than a longer protocol-specific interface. Its 250 kbps limit accommodates many configuration and control links, and the approximately 300 mV receiver hysteresis provides a degree of noise immunity in industrial environments. The commercial temperature range of 0°C to 70°C covers typical indoor equipment. Verify the cable length, ground reference, connector pin assignment, and whether the linked devices require hardware handshaking before installation.

🔌

External Cable-Facing Interface Card

A cable-facing interface card can use the MAX3232CDWRG4 to provide RS-232 connectivity behind an enclosure opening. The ±15 kV HBM ESD rating on the bus terminals is particularly relevant when users connect and disconnect external cables. Its integrated 3 V to 5.5 V operation reduces external power requirements, and the 16-pin SOIC is suitable for compact embedded boards. The IC protection rating should be treated as one layer of the design: use chassis grounding, cable shielding, connector design, and any required surge protection according to the installation environment.

Tóm tắt các sản phẩm được đề xuất

MAX3232EIDR Texas Instruments Được sử dụng trong: Industrial Serial Console Interface, Point-of-Sale and Peripheral Connectivity, RS-232 Equipment-to-Equipment Link MAX3232CDR Same-family 16-pin SOIC RS-232 transceiver Được sử dụng trong: Industrial Serial Console Interface, Data Acquisition and Test Equipment, Point-of-Sale and Peripheral Connectivity, RS-232 Equipment-to-Equipment Link MAX3232E Improved same-family RS-232 interface option Được sử dụng trong: Data Acquisition and Test Equipment, Embedded Controller Serial Port, External Cable-Facing Interface Card MAX3232IPW Texas Instruments Được sử dụng trong: Embedded Controller Serial Port MAX3232EIPW Texas Instruments Được sử dụng trong: External Cable-Facing Interface Card
What is the MAX3232CDWRG4?
The MAX3232CDWRG4 is a dual-channel RS-232 transceiver from Texas Instruments with two drivers, two receivers, an integrated charge pump, and ±15 kV HBM ESD protection. According to the manufacturer datasheet, it operates from 3 V to 5.5 V and supports signaling rates up to 250 kbps. It is packaged in a 16-pin SOIC and is intended for commercial-temperature equipment operating from 0°C to 70°C.
What is the operating voltage of MAX3232CDWRG4?
The MAX3232CDWRG4 operates from 3 V to 5.5 V. According to the Texas Instruments MAX3232 datasheet, this range allows the same interface circuit to be used with 3.3 V and 5 V system rails. The integrated charge-pump circuitry produces the bipolar voltage levels required by the RS-232 drivers, so the system does not need to provide a separate negative transceiver supply.
What is the maximum data rate of MAX3232CDWRG4?
The MAX3232CDWRG4 supports a maximum data rate of 250 kbps. The Texas Instruments manufacturer datasheet identifies it as a 250 kbps dual-channel RS-232 line driver and receiver. This rate is suitable for many serial consoles, industrial-control links, test instruments, and data-acquisition equipment, although cable length, baud rate, grounding, and system timing must also be checked.
Where can I download the MAX3232CDWRG4 datasheet PDF?
The official MAX3232CDWRG4 datasheet PDF is available from Texas Instruments at https://www.ti.com/lit/ds/symlink/max3232.pdf. The manufacturer product page at https://www.ti.com/product/MAX3232 provides ordering information and additional support material. Use the manufacturer PDF for the authoritative pin description, charge-pump capacitor recommendations, electrical characteristics, and application guidance.
Where can I find the MAX3232CDWRG4 pinout?
The MAX3232CDWRG4 pinout is shown in the pin-description table and package drawing in the Texas Instruments MAX3232 datasheet. The device uses a 16-pin SOIC. Assign PCB nets from that table rather than inferring connections from receiver or driver channel numbers, because the package also includes charge-pump capacitor pins and power connections.
Does the MAX3232CDWRG4 include ESD protection?
Yes. The MAX3232CDWRG4 provides RS-232 bus-terminal ESD protection rated at ±15 kV using the human-body model, according to the Texas Instruments manufacturer datasheet. This rating supports robust handling of cables connected outside an enclosure. ESD protection reduces surge-related stress at the interface, but it does not replace correct signal grounding, shielding, or application-specific surge protection.
What can replace the MAX3232CDWRG4?
A valid direct replacement must use the same 16-pin SOIC footprint and preserve the RS-232 pin assignments, 3 V to 5.5 V supply range, and required data rate. Texas Instruments identifies the MAX3232E as an improved direct drop-in replacement for the MAX3232 family. The MAX3232EIDR is also a 16-pin SOIC option, while MAX3232CDR provides a narrower SOIC package for commercial-temperature designs.
Is MAX3232EIDR a drop-in replacement for MAX3232CDWRG4?
The MAX3232EIDR is a pin-compatible 16-pin SOIC alternative to the MAX3232CDWRG4 and provides the improved MAX3232E implementation. The principal selection difference is environmental and functional refinement: the EIDR variant is intended for an extended industrial temperature range, while the CDWRG4 is specified for 0°C to 70°C. Confirm the complete electrical characteristics and timing requirements against the manufacturer datasheet before releasing the substitution.
What is the best MAX3232E equivalent for MAX3232CDWRG4?
The MAX3232EIDR is the most directly identifiable MAX3232E equivalent listed for the MAX3232CDWRG4 because both use a 16-pin SOIC interface and the MAX3232 family pin arrangement. Texas Instruments describes MAX3232E as an improved direct drop-in replacement for MAX3232. The EIDR option is preferable when an industrial temperature range is needed; the CDWRG4 remains appropriate for commercial 0°C to 70°C equipment.
When should I choose MAX3232CDWRG4 instead of MAX3232EIDR?
Choose the MAX3232CDWRG4 when the equipment is restricted to a 0°C to 70°C ambient range and the MAX3232C feature set is sufficient. Choose the MAX3232EIDR when the design needs the MAX3232E improvements, enhanced interface performance, or an industrial temperature grade. Both use a 16-pin SOIC footprint, so the decision should be based on verified electrical limits, environmental requirements, and qualification rather than package availability.
Is MAX3232CDWRG4 suitable for industrial serial communication?
The MAX3232CDWRG4 is suitable for industrial serial communication only when the enclosure remains within its specified 0°C to 70°C ambient range. Its 250 kbps maximum data rate, 300 mV receiver hysteresis, and ±15 kV HBM ESD protection make it useful for noisy or externally cabled links. For wider industrial temperature requirements, select a verified extended-temperature MAX3232-family option and review its operating limits.
MAX3232CDWRG4 vs MAX3232CDR: which one should I use?
The MAX3232CDWRG4 uses a 16-pin wide-body SOIC, while the MAX3232CDR uses a 16-pin narrow-body SOIC. The MAX3232CDWRG4 is therefore not a footprint-identical PCB replacement for the CDR. Both belong to the commercial MAX3232C family, but package width, lead pitch, and board layout must be checked before treating either part as a drop-in replacement for the other.
Where can I buy MAX3232CDWRG4 online?
Use the Request a Quote form on this page to request MAX3232CDWRG4 availability, current lead time, and a quotation for the required quantity. The form provides a direct purchasing path without embedding figures that may change between quote sessions. Confirm the exact 16-pin SOIC order code, commercial temperature grade, and tape-and-reel or other required shipping format with the supplier.
What is the price of MAX3232CDWRG4?
Current MAX3232CDWRG4 pricing depends on quantity, package shipment form, and sourcing conditions. Use the Request a Quote form on this page to obtain a current quotation and minimum order quantity. The request should identify the complete MPN MAX3232CDWRG4, required quantity, and delivery format so the commercial response corresponds to the correct 16-pin SOIC configuration.
Is MAX3232CDWRG4 in stock and what is its lead time?
Stock and lead time should be confirmed through the Request a Quote form on this page because they can vary with quantity and shipment format. Include the exact MPN MAX3232CDWRG4 and state whether tape-and-reel or another delivery format is required. The manufacturer identifies MAX3232 as a current 3 V to 5.5 V dual RS-232 transceiver family, but current allocation must be confirmed for each order.

Dữ liệu tham khảo kỹ thuật cho MAX3232CDWRG4 — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.

Hướng dẫn chọn lựa

Choose the MAX3232CDWRG4 for a commercial-temperature, wide-body 16-pin SOIC design that operates from 3 V to 5.5 V, supports RS-232 signaling up to 250 kbps, and requires ±15 kV HBM ESD protection at the bus terminals. Choose the MAX3232EIDR when the same board requires an industrial temperature range or the improved MAX3232E implementation. MAX3232EIPW and MAX3232IPW are appropriate when an extended-temperature MAX3232-family part is needed. Choose MAX3232CDR only after confirming that the narrow SOIC body matches the PCB land pattern and that all electrical requirements are unchanged. The generic MAX3232E family designation is useful for functional evaluation, but a production order must use an exact suffix defining package width, temperature grade, and shipment format. For any substitution, verify pin assignments, charge-pump capacitor connections, supply limits, receiver thresholds, timing, and environmental requirements against the manufacturer datasheet.

So sánh với các sản phẩm thay thế

Tham số Sản phẩm này MAX3232EIDR MAX3232EIPW MAX3232IPW MAX3232CDR MAX3232E
Package 16-SOIC wide body 16-SOIC 16-SOIC 16-SOIC 16-SOIC narrow body 16-SOIC
Brand Texas Instruments Texas Instruments Texas Instruments Texas Instruments Texas Instruments Texas Instruments
Channel Configuration 2 driver and 2 receiver channels 2 driver and 2 receiver channels 2 driver and 2 receiver channels 2 driver and 2 receiver channels 2 driver and 2 receiver channels 2 driver and 2 receiver channels
Supply Voltage Range 3 V to 5.5 V 3 V to 5.5 V 3 V to 5.5 V 3 V to 5.5 V 3 V to 5.5 V 3 V to 5.5 V
Maximum Data Rate 250 kbps 250 kbps 250 kbps 250 kbps 250 kbps 250 kbps
ESD Protection ±15 kV HBM ±15 kV HBM ±15 kV HBM ±15 kV HBM ±15 kV HBM ±15 kV HBM
Temperature Grade Commercial, 0°C to 70°C Industrial, -40°C to 85°C Industrial, -40°C to 85°C Extended temperature Commercial, 0°C to 70°C Selectable by package suffix
Receiver Hysteresis 300 mV 300 mV 300 mV 300 mV 300 mV 300 mV

Bảo phân biệt quan trọng

  • Improved same-family replacement option (vsMAX3232EIDR)
  • Compact two-channel interface (vsMAX3232CDR)
  • Single-rail bipolar voltage generation (vsMAX3232IPW)
  • Connector-facing ESD resilience (vsMAX3232E)

Ghi chú thiết kế

Place the MAX3232 charge-pump capacitors directly between the capacitor pins and the nearest available ground plane, with the shortest possible traces. Keep the supply bypass capacitor adjacent to VCC and ground pins, and provide an uninterrupted ground reference beneath the device. Because the circuit develops bipolar RS-232 voltage internally, follow the manufacturer layout drawing exactly rather than treating the charge-pump section as an ordinary low-current logic block.

Route each RS-232 driver output directly toward its connector, keep receiver inputs away from those outputs, and avoid placing long parallel traces beneath the transceiver. Where a board supports both RS-232 and another high-energy interface, maintain separation to reduce differential crosstalk. Connect the signal ground according to the system grounding strategy and use a dedicated connector-side return path when long or externally accessible cables are involved.

Do not substitute every 16-pin SOIC RS-232 device solely because the package pin count matches. Verify the SOIC body width and lead pitch, the number and arrangement of driver and receiver pins, charge-pump capacitor connections, supply limits, maximum data rate, and temperature grade. MAX3232CDR, for example, is a narrow-body 16-pin SOIC and may not match the land pattern of the wide-body MAX3232CDWRG4 even though both use the same family name.

The MAX3232 generates the bipolar voltages required by RS-232 through an internal charge pump, so supply and ground return paths can carry high-frequency ripple even though the data rate is only 250 kbps. Decouple the supply close to the IC, maintain a compact ground return for charge-pump current, and avoid routing sensitive analog or high-speed digital traces beneath the switched-capacitor section. ESD protection helps at the connector but does not eliminate the need for shielding and correct grounding.

Thông tin tuân thủ

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
Không chì
Unknown
Không halogen
Unknown
Khoáng vật xung đột
Unknown

The manufacturer documentation identifies a commercial-temperature RS-232 interface IC, but explicit RoHS, REACH, lead-free, halogen-free, conflict-minerals, and automotive qualification statements were not identified for the exact orderable MPN.

Dữ liệu được xác minh vào: 2026-11-09 — dữ liệu được xác minh và quản lý bởi đội ngũ kỹ thuật phần cứng của XAIPART

Tìm kiếm liên quan

MAX3232CDWRG4 datasheet MAX3232CDWRG4 pinout MAX3232CDWRG4 datasheet pdf MAX3232CDWRG4 equivalent MAX3232CDWRG4 replacement MAX3232CDWRG4 cross reference MAX3232CDWRG4 price MAX3232CDWRG4 stock Texas Instruments MAX3232CDWRG4 MAX3232CDWRG4 16-SOIC MAX3232CDWRG4 250kbps RS-232 MAX3232CDWRG4 vs MAX3232EIDR MAX3232CDWRG4 application circuit MAX3232 3V RS-232 transceiver

Các bộ phận và thuật ngữ liên quan

Texas Instruments MAX3232CDWRG4 MAX3232EIDR MAX3232EIPW MAX3232IPW MAX3232CDR MAX3232E RS-232 RS-232 transceiver line driver line receiver interface IC semiconductor 3 V to 5.5 V power supply 250 kbps data rate ±15 kV HBM ESD protection 300 mV receiver hysteresis integrated charge pump 16-SOIC SOIC package family surface-mount technology commercial temperature grade serial communication industrial serial interface
Báo giá nhanh RFQ
Hãy điền đầy đủ thông tin — đội ngũ bán hàng của chúng tôi sẽ phản hồi trong vòng 24 giờ
Mã sản phẩm Nhà sản xuất Kiểu đóng gói QTY Giá mục tiêu Phụ
✓
Báo giá đã gửi!

Chúng tôi sẽ trả lời email của bạn trong vòng 24 giờ

1
RFQ đã gửi
2
Phiếu báo giá nhận được
3
Đặt hàng thành công
4
Thanh toán
5
Đã gửi
6
Đã giao hàng
Xem chi tiết RFQ