Texas Instruments

MAX3232EIPWRSV - 250kbps Dual RS-232 Transceiver | Texas Instruments

MPN: MAX3232EIPWRSV ✓ فعال
3 V to 5.5 V Vdss 16-pin SSOP Package
MOQ: 1 |

MAX3232EIPWRSV جائزہ

The Texas Instruments MAX3232EIPWRSV is a dual-channel RS-232 line driver and receiver operating from a 3 V to 5.5 V supply at up to 250 kbps. It integrates two line drivers, two line receivers, and a dual charge-pump circuit with plus or minus 15 kV IEC ESD protection on the serial-port terminals. The device is packaged in a 16-pin SSOP package.

A transceiver, also called a line driver/receiver, converts logic-level UART signals into RS-232 bipolar voltage levels and converts received RS-232 levels back into CMOS-compatible logic. The MAX3232E belongs to the RS-232 interface IC hierarchy, where it sits between a UART controller and a DB9, terminal, or other serial connector. Its charge-pump circuit generates the positive and negative voltages required by the TIA/EIA-232-F interface without a separate negative power supply.

The MAX3232E family provides plus or minus 15 kV IEC ESD protection, automatic driver slew control, and operation from both 3 V and 5 V systems. A single device supports two serial channels through two drivers and two receivers. The dual architecture is useful for console management, configuration ports, instrument control, and industrial equipment that exchanges data with legacy RS-232 equipment.

Its internal design uses a dual charge-pump circuit to produce the RS-232 voltage swings while maintaining a low-voltage CMOS supply. The driver outputs include slew-rate control to limit electromagnetic interference and help control ringing on the cable. The receiver side provides signal conditioning for reliable interpretation of the bipolar RS-232 signal, while the integrated ESD structures protect the external terminals.

Typical uses include industrial controllers, laboratory instruments, POS terminals, security equipment, and service interfaces. Since many modern computers no longer include an RS-232 port, the MAX3232E remains valuable for connecting embedded controllers and legacy peripherals. It can also translate between a 3.3 V UART and a 5 V-powered RS-232 link where appropriate logic levels and cable requirements are observed.

When laying out the circuit, place the charge-pump capacitors and the required ceramic bypass capacitor close to their associated pins. Route each RS-232 driver output directly to its connector and keep the protected connector-side traces short and away from sensitive analog or high-speed digital nets. Confirm the connector pinout, cable length, ground reference, and signal polarity before populating the board.

This page combines manufacturer specifications, ordering data, drop-in replacement options, and practical interface-design guidance in one place. It also organizes the differences among MAX3232, MAX3232E, TRS3232E, MAX3243E, and TRS3243E so engineers can shortlist a compatible transceiver without overlooking supply or logic-level details.

کے لیے ڈراپ اِن متبادل MAX3232EIPWRSV — یکساں پیکیج، پن سے پن مطابقت پذیر۔ مختلف پیکیج والے پرزے جن کے لیے PCB دوبارہ کام درکار ہو، شامل نہیں ہیں۔

اس سیریز میں مختلف ورژن

اسی سیریز کے ماڈلز جو ڈراپ اِن مطابقت رکھتے ہیں MAX3232EIPWRSV (یکساں فارم فیکٹر اور فٹ پرنٹ) — میں مختلف Package.

Texas Instruments
Package: 16-TSSOP (0.173 in, 4.40 mm width)
موازنہ کریں MAX3232EIPWRSV →

MAX3232EIPWV+T

✅ ڈراپ-اِن ⚠️ تفصیلات غیر تصدیق شدہ
📦 16-pin SSOP
Same MAX3232E electrical ratings and pin functions; alternate manufacturer reel suffix, with no stated change to the 250 kbps data rate, 3 V to 5.5 V supply, or plus or minus 15 kV ESD protection

📋 حوالہ جاتی متبادل (کیٹلاگ میں نہیں)

TRS3232EIPWV+T

✅ ڈراپ-اِن
📦 16-pin SSOP
Same dual-transceiver function and 250 kbps class, with enhanced internal features in the TRS3232E family; verify charge-pump capacitor values and logic-level details before substitution

📋 حوالہ جاتی متبادل (کیٹلاگ میں نہیں)

MAX3243EIPWV+T

✅ ڈراپ-اِن
📦 16-pin SSOP
Separate low-voltage logic-supply arrangement replaces the common-supply configuration, while the RS-232 terminal data rate remains in the same 250 kbps class

📋 حوالہ جاتی متبادل (کیٹلاگ میں نہیں)

TRS3243EIPWV+T

✅ ڈراپ-اِن ⚠️ تفصیلات غیر تصدیق شدہ
📦 16-pin SSOP
Enhanced TRS3243E transceiver with a separate logic-supply arrangement; data rate remains 250 kbps but power architecture and capacitor implementation must be checked

📋 حوالہ جاتی متبادل (کیٹلاگ میں نہیں)

MAX3232EIPWG4

✅ ڈراپ-اِن
Texas Instruments
📦 16-pin SSOP
RS-232 Line Driver/Receiver · 2 · 2 · 3 V to 5.5 V · 250 kbps · +/-15 kV · +/-8 kV · +/-15 kV

قیمت کے لیے رابطہ کریں

ڈیٹا شیٹ دیکھیں →

MAX3232EIPWRSV تفصیلات

Product Type Dual RS-232 line driver and receiver
Number of Drivers 2
Number of Receivers 2
Supply Voltage Range 3 V to 5.5 V
Maximum Data Rate 250 kbps
ESD Protection +/-15 kV IEC ESD
RS-232 Standard TIA/EIA-232-F
Charge-Pump Circuit Dual charge-pump circuit
انٹرفیس ٹائپ RS-232
پیکیج 16-pin SSOP
ماؤنٹنگ ٹائپ Surface Mount
Automotive Qualification Not applicable
RoHS اسٹیٹس Compliant
ESD Protection Method IEC 61000-4-2

MAX3232EIPWRSV پن کنفیگریشن

SSOP-16 Package Pinout Diagram SSOP-16 3.9x6.0mm, P0.635mm, JEDEC MO-150. 1 16 2 15 3 14 4 13 5 12 6 11 7 10 8 9 SSOP-16
پن 1 C1+ — Charge-pump flying capacitor positive terminal
پن 2 C1- — Charge-pump flying capacitor negative terminal
پن 3 T1OUT — RS-232 driver 1 output
پن 4 R1IN — RS-232 receiver 1 input
پن 5 R1OUT — Logic-level receiver 1 output
پن 6 T2IN — Logic-level driver 2 input
پن 7 T2OUT — RS-232 driver 2 output
پن 8 R2IN — RS-232 receiver 2 input
پن 9 GND — Ground
پن 10 V+ — Positive charge-pump output
پن 11 VCC — Positive supply input
پن 12 V- — Negative charge-pump output
پن 13 C2+ — Charge-pump flying capacitor positive terminal
پن 14 C2- — Charge-pump flying capacitor negative terminal
پن 15 R2OUT — Logic-level receiver 2 output
پن 16 T1IN — Logic-level driver 1 input

عام استعمالات

MAX3232EIPWRSV کے لیے موزوں ہے 6 ایپلیکیشنs: Industrial Console and Configuration Port, Laboratory Instrument Control Interface, Point-of-Sale and Retail Terminal Interface, Embedded UART to Legacy Peripheral Bridge, Security and Access-Control Systems, Data Acquisition and Remote Control Equipment.

🏭

Industrial Console and Configuration Port

The MAX3232EIPWRSV fits a service console that must connect a modern controller to a legacy RS-232 terminal. Its 250 kbps maximum data rate provides ample margin for typical asynchronous console traffic, while the 3 V to 5.5 V supply range supports both 3.3 V and 5 V system rails. The integrated dual charge-pump circuit produces the required RS-232 voltage swings without a negative supply. Place the charge-pump and bypass capacitors close to their pins, route T1OUT and T2OUT toward the connector, and keep the ESD-protected terminal traces short to improve industrial noise immunity.

🔧

Laboratory Instrument Control Interface

The MAX3232EIPWRSV provides a compact interface between an embedded controller and a test instrument that retains an RS-232 port. The dual-channel arrangement can support one command channel and one status channel without adding another transceiver. Operation from 3 V to 5.5 V allows the interface to share the instrument controller's supply, and plus or minus 15 kV IEC ESD protection adds resilience at the exposed connector. Verify the instrument's TIA/EIA-232-F signal polarity and use a cable with the correct D-sub wiring rather than assuming DB9 pin assignments are universal.

🖥️

Point-of-Sale and Retail Terminal Interface

The MAX3232EIPWRSV is suitable for point-of-sale equipment, receipt printers, or scanners that communicate through an RS-232 service port. The 250 kbps signaling capability is well above normal peripheral baud rates, and the 3 V to 5.5 V operating range supports compact embedded systems with either 3.3 V or 5 V rails. The dual driver and receiver arrangement allows two RS-232 links in a small footprint. Keep the connector-side routing compact, provide a reliable chassis and signal-ground strategy, and confirm the peripheral's voltage-level and handshake requirements before production release.

🔌

Embedded UART to Legacy Peripheral Bridge

The MAX3232EIPWRSV bridges a CMOS UART from a controller or microcontroller to a legacy peripheral that exposes only RS-232. Its dual charge-pump circuit generates the bipolar RS-232 levels required by the peripheral while the device continues to operate from a low-voltage supply. A 250 kbps maximum rate supports asynchronous data transfer well beyond the baud rates normally used by legacy peripherals. Use one driver and one receiver for a single-ended link, or use both channels when the peripheral supports two-way control and status signaling.

🛡️

Security and Access-Control Systems

The MAX3232EIPWRSV can serve as the maintenance interface for access-control panels, cameras, or alarm controllers that retain an RS-232 commissioning port. Its plus or minus 15 kV IEC ESD protection is valuable when the connector may be touched by installers or exposed to discharged static, although it does not replace enclosure-level surge protection. The 3 V to 5.5 V supply range simplifies integration with low-voltage controllers, and the dual-channel capability can serve two independent service interfaces. Route the driver outputs directly to the connector and avoid sharing unprotected external traces with sensitive sensor wiring.

📊

Data Acquisition and Remote Control Equipment

The MAX3232EIPWRSV supports legacy remote-control and data-acquisition equipment that uses RS-232 for configuration commands or sensor data transfer. At up to 250 kbps, it covers high-speed asynchronous instrument traffic while operating from the same 3 V to 5.5 V supply family used by embedded control hardware. The compact 16-pin SSOP package preserves board area, and the dual architecture can separate control and measurement channels. Verify cable length and grounding at the system level because both affect signal integrity even when the local transceiver meets the specified data rate.

تجویز کردہ پروڈکٹس کا خلاصہ

MAX3243EIPWV+T RS-232 transceiver with separate logic-supply architecture استعمال ہوتا ہے: Industrial Console and Configuration Port, Point-of-Sale and Retail Terminal Interface, Security and Access-Control Systems TRS3232EIPWV+T Enhanced family-compatible RS-232 interface استعمال ہوتا ہے: Industrial Console and Configuration Port, Laboratory Instrument Control Interface, Security and Access-Control Systems MAX3232EIPWV+T Direct same-family transceiver option استعمال ہوتا ہے: Laboratory Instrument Control Interface, Embedded UART to Legacy Peripheral Bridge, Data Acquisition and Remote Control Equipment TRS3243EIPWV+T Enhanced dual RS-232 interface option استعمال ہوتا ہے: Point-of-Sale and Retail Terminal Interface, Data Acquisition and Remote Control Equipment MAX3232 Manufacturer-identified legacy drop-in family استعمال ہوتا ہے: Embedded UART to Legacy Peripheral Bridge
What is the operating voltage range of MAX3232EIPWRSV?
The MAX3232EIPWRSV operates from a 3 V to 5.5 V supply. According to the Texas Instruments MAX3232E manufacturer datasheet, this range allows the same interface circuit to serve 3.3 V and 5 V systems. The internal charge pumps generate the positive and negative voltages required at the RS-232 terminals, while the logic side remains compatible with the host supply. External bypass and charge-pump capacitors must still be placed exactly as shown in the datasheet application circuit.
What is the maximum data rate of MAX3232EIPWRSV?
The MAX3232EIPWRSV supports data rates up to 250 kbps. Texas Instruments specifies this figure for the MAX3232E dual RS-232 transceiver in the manufacturer datasheet. The device is appropriate for asynchronous UART links operating substantially below that limit, including console, configuration, and instrument-control ports. Cable length, baud rate, connector wiring, and grounding remain system-level constraints and must be checked even when the selected transceiver meets the required signaling rate.
Where can I download the MAX3232EIPWRSV datasheet PDF?
The MAX3232EIPWRSV datasheet is available from Texas Instruments through the official MAX3232E product page and the direct MAX3232 datasheet PDF link listed on this page. The document covers the electrical characteristics, charge-pump circuit, typical application, pin descriptions, and RS-232 interface information for the MAX3232E family. Use the pin-description table and ordering-information section when assigning PCB tracks or confirming the suffix-specific package.
What is the MAX3232EIPWRSV pinout?
The MAX3232EIPWRSV uses a 16-pin SSOP arrangement with one driver input, two driver outputs, two receiver inputs, two receiver outputs, charge-pump capacitor terminals, supply pins, and ground. According to the Texas Instruments MAX3232E manufacturer datasheet, the standard MAX3232 pin sequence is C1+, C1-, T1OUT, R1IN, R1OUT, T2IN, T2OUT, R2IN, GND, V+, VCC, V-, C2+, C2-, R2OUT, and T1IN. Verify the pin-description table before assigning connector signals.
What can replace the MAX3232EIPWRSV?
The closest same-family replacements include the MAX3232EIPWV+T and, for designs that can tolerate different internal functions, MAX3243EIPWV+T and TRS3232EIPWV+T in compatible 16-pin variants. Texas Instruments identifies the MAX3232E as an improved direct drop-in replacement for the original MAX3232. A replacement should always be checked for exact package drawing, pin function, supply arrangement, and capacitor values rather than relying only on the family name.
Is the MAX3232EIPWRSV the same as the MAX3232EIPWR?
The MAX3232EIPWRSV and MAX3232EIPWR belong to the same MAX3232E family, but the final package or ordering suffix must be checked before treating them as interchangeable. The target ordering code uses the V package designation, while the IPWR listing identifies the PW variant. Both are associated with 16-lead surface-mount options, but package drawings, lead widths, and reel codes can differ. Confirm the mechanical drawing and pin list for the exact suffix placed on the order.
What are the key specifications engineers should know about MAX3232EIPWRSV?
The key MAX3232EIPWRSV specifications are a 3 V to 5.5 V supply range, two RS-232 drivers, two receivers, a 250 kbps maximum data rate, and plus or minus 15 kV IEC ESD protection. The device also uses a dual charge-pump circuit and meets the TIA/EIA-232-F interface requirements described in the Texas Instruments manufacturer datasheet. Its 16-pin SSOP package supports compact surface-mount designs where the required charge-pump and bypass capacitors fit.
Where can I buy MAX3232EIPWRSV online?
Use the Request a Quote form on this page to request MAX3232EIPWRSV availability, current unit pricing, and a shipment quotation. The form provides a direct purchasing channel without requiring a static price table that can become outdated. When requesting a quote, include the required quantity, target reel or cut-tape format, and any date-code or traceability requirements so the order can be prepared correctly.
How much does MAX3232EIPWRSV cost?
Current pricing for the MAX3232EIPWRSV is generated through the Request a Quote form on this page. The displayed commercial tier reflects the selected quantity and order configuration at the time the quotation is produced. Submit the required quantity and packaging preference to receive the applicable unit price and total order value. Volume breaks, reel quantities, and sourcing conditions should be confirmed on the quotation rather than inferred from a generic single-unit figure.
What is the lead time for MAX3232EIPWRSV?
Request the current MAX3232EIPWRSV lead time through the Request a Quote form on this page. Lead time depends on the requested quantity, manufacturing availability, and shipment destination. Include the required quantity and production schedule when submitting the request. For scheduled programs, confirm buffer stock and any lot or date-code requirements before committing the component to a board build.
Is MAX3232EIPWRSV in stock?
The current stock position for MAX3232EIPWRSV is available through the Request a Quote form on this page. Submit the required quantity and reel or cut-tape packaging preference to obtain an availability confirmation. Because inventory can change between quotation requests, treat the answer on the quotation as the controlling commitment rather than relying on a cached landing-page availability statement.
MAX3232EIPWRSV vs MAX3232EIPWR - which package should I choose?
Choose the suffix that matches the PCB footprint and required reel format rather than selecting by electrical function alone. The MAX3232EIPWRSV ordering code identifies the V package designation, while MAX3232EIPWR identifies the PW variant. Although both are members of the MAX3232E family, their mechanical drawings and shipping formats may differ. Compare the official package drawings and pin assignments, and use the exact ordering code required by your assembler.
When should I choose MAX3232EIPWRSV instead of MAX3243E?
Choose the MAX3232EIPWRSV for a conventional RS-232 link where both logic and supply operation follow the MAX3232E arrangement. A MAX3243E-family device adds a separate low-voltage logic supply arrangement and should be selected when the host UART requires a distinct 3.3 V logic rail. The MAX3232EIPWRSV offers the simpler 3 V to 5.5 V implementation at up to 250 kbps with plus or minus 15 kV IEC ESD protection.
Is MAX3232EIPWRSV suitable for an industrial RS-232 controller?
The MAX3232EIPWRSV is suitable for industrial RS-232 controller links when the 3 V to 5.5 V supply, 250 kbps data rate, and TIA/EIA-232-F interface requirements fit the system. Its plus or minus 15 kV IEC ESD protection strengthens the external serial-port connection in electrically noisy environments. The enclosure, cable routing, ground reference, and isolation strategy still determine the field reliability of the complete communication port.
What is the best cross-brand equivalent for MAX3232EIPWRSV?
There is no cross-brand equivalent identified in the manufacturer comparison data for the exact MAX3232EIPWRSV ordering code. Texas Instruments instead identifies MAX3232, MAX3232E, and TRS3232E as related devices and explicitly describes the MAX3232E as an improved direct drop-in replacement for MAX3232. For a second-source design, compare the candidate's pinout, supply voltage, logic levels, data rate, charge-pump capacitor values, and package drawing before approving any substitute.

کے لیے انجینئرنگ ریفرنس ڈیٹا MAX3232EIPWRSV — موازنہ، ڈیزائن رہنمائی، اور تعمیل کی معلومات۔

انتخاب کی گائیڈ

Choose the MAX3232EIPWRSV when the design needs a straightforward dual-channel RS-232 interface running from a 3 V to 5.5 V system supply and requires the enhanced MAX3232E family behavior, including plus or minus 15 kV IEC ESD protection. Use the MAX3243EIPWV+T when the host UART needs a separately controlled low-voltage logic rail, but review its power architecture and capacitor network first. Consider the TRS3232EIPWV+T for an enhanced family option, while validating its specific electrical and application details. The original MAX3232 can serve legacy designs because Texas Instruments identifies MAX3232E as an improved direct drop-in replacement. In every case, verify the exact suffix package drawing, pin function, capacitor values, connector wiring, and cable grounding before approving a substitution.

متبادلات کے ساتھ موازنہ

پیرامیٹر یہ پروڈکٹ MAX3232EIPWV+T TRS3232EIPWV+T MAX3243EIPWV+T TRS3243EIPWV+T MAX3232
Brand Texas Instruments Texas Instruments Texas Instruments Texas Instruments Texas Instruments Texas Instruments
Package 16-pin SSOP 16-pin SSOP 16-pin SSOP 16-pin SSOP 16-pin SSOP 16-pin SSOP
Interface RS-232 RS-232 RS-232 RS-232 RS-232 RS-232
Number of Drivers 2 2 2 2 2 2
Number of Receivers 2 2 2 2 2 2

اہم امتیازی خصوصیات

  • Single-supply RS-232 operation simplifies the host power architecture (بمقابلہMAX3243EIPWV+T)
  • Integrated external-terminal ESD protection (بمقابلہMAX3232)
  • Dual-channel interface in a compact surface-mount package (بمقابلہTRS3232EIPWV+T)

ڈیزائن نوٹس

Place the two charge-pump flying capacitors and the supply bypass capacitor close to the MAX3232EIPWRSV pins shown in the Texas Instruments application circuit. Keep the RS-232 driver outputs and receiver inputs on short, direct routes to the connector. These signals experience larger voltage transitions than the logic side, so separating them from sensitive analog traces reduces capacitive coupling. Maintain the component spacing and capacitor values specified in the manufacturer datasheet rather than substituting larger packages with different parasitics.

Keep the external RS-232 traces away from high-speed clocks and switching-node edges because the bipolar line-driver transitions can couple into nearby circuits. Use a continuous ground reference and route the cable-side ground directly to the connector return. If the cable is externally accessible, retain the transceiver's IEC 61000-4-2 protection rating in the system design and add enclosure or TVS protection when the required surge level exceeds the transceiver's capability.

Do not substitute a MAX3232-family device solely by its driver and receiver count. The MAX3232E and MAX3243E variants use different supply arrangements, while TRS3232E and TRS3243E may require different charge-pump capacitor values or interface details. Compare the exact pin function, package drawing, logic levels, and capacitor network for every revision before releasing a substitution. Also verify DB9 signal names and polarity because connector numbering is not consistent across RS-232 equipment.

The MAX3232EIPWRSV uses slew control on the RS-232 drivers, but the external cable still radiates common-mode energy. Route the two driver outputs as short PCB traces and avoid adding large loops or test pads that increase their effective length. Keep the connector mechanically fixed to the chassis where possible, use a suitable shield or filtered connector for enclosure entry, and maintain a low-impedance return path between the interface ground and the equipment reference network.

تعمیل کی معلومات

RoHS
Compliant
REACH
Unknown
AEC-Q100
Not Applicable
لیڈ فری
Unknown
ہیلوجن فری
Unknown
کنفلیکٹ منرلز
Unknown

The product listing identifies the MAX3232EIPWRSV as RoHS compliant. The Texas Instruments product page identifies plus or minus 15 kV IEC ESD protection and compliance with TIA/EIA-232-F. This RS-232 interface IC is not an automotive-qualified product.

ڈیٹا کی تصدیق کی تاریخ: 2026-11-09 — ڈیٹا XAIPART کی کمپوننٹ انجینئرنگ ٹیم کے ذریعے تصدیق شدہ اور ترتیب شدہ

متعلقہ تلاشیں

max3232eipwr datasheet MAX3232EIPWRSV datasheet MAX3232EIPWRSV datasheet pdf MAX3232EIPWRSV pinout MAX3232EIPWRSV SSOP-16 MAX3232EIPWRSV replacement MAX3232EIPWRSV equivalent MAX3232EIPWRSV cross reference MAX3232EIPWRSV vs MAX3243EIPWV+T MAX3232EIPWRSV application circuit MAX3232EIPWRSV ESD protection MAX3232EIPWRSV price Texas Instruments MAX3232EIPWRSV MAX3232EIPWRSV RS-232 transceiver

متعلقہ اجزاء اور اصطلاحات

Texas Instruments MAX3232EIPWRSV MAX3232E MAX3232 TRS3232E MAX3243E TRS3243E RS-232 transceiver line driver line receiver RS-232 interface IC UART transceiver dual charge-pump circuit TIA/EIA-232-F IEC 61000-4-2 ESD protection 250 kbps 3 V to 5.5 V supply 16-pin SSOP SSOP package family surface mount industrial console laboratory instrument control legacy peripheral bridge
فوری کوٹ RFQ
مکمل تفصیلات بھریں — ہماری سیلز ٹیم 24 گھنٹوں میں جواب دے گی
پارٹ نمبر مینوفیکچرر پیکج QTY ہدف قیمت کل رقم
✓
کوٹ جمع ہو گیا!

ہم 24 گھنٹوں کے اندر آپ کے ای میل کا جواب دیں گے

1
RFQ جمع ہو گیا
2
کوٹ موصول ہو گیا
3
آرڈر دے دیا گیا
4
ادائیگی
5
بھیج دیا گیا
6
ڈیلیور شدہ
RFQ تفصیلات دیکھیں