MAX3232EIPWRSV - 250kbps Dual RS-232 Transceiver | Texas Instruments
Артикул: MAX3232EIPWRSV ✓ АктивенMAX3232EIPWRSV Обзор
A transceiver, also called a line driver/receiver, converts logic-level UART signals into RS-232 bipolar voltage levels and converts received RS-232 levels back into CMOS-compatible logic. The MAX3232E belongs to the RS-232 interface IC hierarchy, where it sits between a UART controller and a DB9, terminal, or other serial connector. Its charge-pump circuit generates the positive and negative voltages required by the TIA/EIA-232-F interface without a separate negative power supply.
The MAX3232E family provides plus or minus 15 kV IEC ESD protection, automatic driver slew control, and operation from both 3 V and 5 V systems. A single device supports two serial channels through two drivers and two receivers. The dual architecture is useful for console management, configuration ports, instrument control, and industrial equipment that exchanges data with legacy RS-232 equipment.
Its internal design uses a dual charge-pump circuit to produce the RS-232 voltage swings while maintaining a low-voltage CMOS supply. The driver outputs include slew-rate control to limit electromagnetic interference and help control ringing on the cable. The receiver side provides signal conditioning for reliable interpretation of the bipolar RS-232 signal, while the integrated ESD structures protect the external terminals.
Typical uses include industrial controllers, laboratory instruments, POS terminals, security equipment, and service interfaces. Since many modern computers no longer include an RS-232 port, the MAX3232E remains valuable for connecting embedded controllers and legacy peripherals. It can also translate between a 3.3 V UART and a 5 V-powered RS-232 link where appropriate logic levels and cable requirements are observed.
When laying out the circuit, place the charge-pump capacitors and the required ceramic bypass capacitor close to their associated pins. Route each RS-232 driver output directly to its connector and keep the protected connector-side traces short and away from sensitive analog or high-speed digital nets. Confirm the connector pinout, cable length, ground reference, and signal polarity before populating the board.
This page combines manufacturer specifications, ordering data, drop-in replacement options, and practical interface-design guidance in one place. It also organizes the differences among MAX3232, MAX3232E, TRS3232E, MAX3243E, and TRS3243E so engineers can shortlist a compatible transceiver without overlooking supply or logic-level details.
Аналоги без доработки для MAX3232EIPWRSV — тот же корпус, pin-to-pin совместимость. Компоненты в других корпусах, требующие переработки PCB, исключены.
Варианты в этой серии
Модели той же серии, совместимые без доработки с MAX3232EIPWRSV (тот же форм-фактор и посадочное место) — отличается по Package.
MAX3232EIPWV+T
✅ Прямая замена ⚠️ Характеристики не проверены📋 Справочный аналог (нет в каталоге)
TRS3232EIPWV+T
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
MAX3243EIPWV+T
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
TRS3243EIPWV+T
✅ Прямая замена ⚠️ Характеристики не проверены📋 Справочный аналог (нет в каталоге)
MAX3232EIPWG4
✅ Прямая заменаУточнить цену
Открыть даташит →MAX3232EIPWRSV Характеристики
| Product Type | Dual RS-232 line driver and receiver |
| Number of Drivers | 2 |
| Number of Receivers | 2 |
| Supply Voltage Range | 3 V to 5.5 V |
| Maximum Data Rate | 250 kbps |
| ESD Protection | +/-15 kV IEC ESD |
| RS-232 Standard | TIA/EIA-232-F |
| Charge-Pump Circuit | Dual charge-pump circuit |
| Тип интерфейса | RS-232 |
| Корпус | 16-pin SSOP |
| Тип монтажа | Surface Mount |
| Automotive Qualification | Not applicable |
| Статус RoHS | Compliant |
| ESD Protection Method | IEC 61000-4-2 |
Конфигурация выводов MAX3232EIPWRSV
| Контакт 1 | C1+ — Charge-pump flying capacitor positive terminal |
| Контакт 2 | C1- — Charge-pump flying capacitor negative terminal |
| Контакт 3 | T1OUT — RS-232 driver 1 output |
| Контакт 4 | R1IN — RS-232 receiver 1 input |
| Контакт 5 | R1OUT — Logic-level receiver 1 output |
| Контакт 6 | T2IN — Logic-level driver 2 input |
| Контакт 7 | T2OUT — RS-232 driver 2 output |
| Контакт 8 | R2IN — RS-232 receiver 2 input |
| Контакт 9 | GND — Ground |
| Контакт 10 | V+ — Positive charge-pump output |
| Контакт 11 | VCC — Positive supply input |
| Контакт 12 | V- — Negative charge-pump output |
| Контакт 13 | C2+ — Charge-pump flying capacitor positive terminal |
| Контакт 14 | C2- — Charge-pump flying capacitor negative terminal |
| Контакт 15 | R2OUT — Logic-level receiver 2 output |
| Контакт 16 | T1IN — Logic-level driver 1 input |
Типичное применение
MAX3232EIPWRSV подходит для 6 применениеs: Industrial Console and Configuration Port, Laboratory Instrument Control Interface, Point-of-Sale and Retail Terminal Interface, Embedded UART to Legacy Peripheral Bridge, Security and Access-Control Systems, Data Acquisition and Remote Control Equipment.
Industrial Console and Configuration Port
The MAX3232EIPWRSV fits a service console that must connect a modern controller to a legacy RS-232 terminal. Its 250 kbps maximum data rate provides ample margin for typical asynchronous console traffic, while the 3 V to 5.5 V supply range supports both 3.3 V and 5 V system rails. The integrated dual charge-pump circuit produces the required RS-232 voltage swings without a negative supply. Place the charge-pump and bypass capacitors close to their pins, route T1OUT and T2OUT toward the connector, and keep the ESD-protected terminal traces short to improve industrial noise immunity.
Рекомендуется
Laboratory Instrument Control Interface
The MAX3232EIPWRSV provides a compact interface between an embedded controller and a test instrument that retains an RS-232 port. The dual-channel arrangement can support one command channel and one status channel without adding another transceiver. Operation from 3 V to 5.5 V allows the interface to share the instrument controller's supply, and plus or minus 15 kV IEC ESD protection adds resilience at the exposed connector. Verify the instrument's TIA/EIA-232-F signal polarity and use a cable with the correct D-sub wiring rather than assuming DB9 pin assignments are universal.
Рекомендуется
Point-of-Sale and Retail Terminal Interface
The MAX3232EIPWRSV is suitable for point-of-sale equipment, receipt printers, or scanners that communicate through an RS-232 service port. The 250 kbps signaling capability is well above normal peripheral baud rates, and the 3 V to 5.5 V operating range supports compact embedded systems with either 3.3 V or 5 V rails. The dual driver and receiver arrangement allows two RS-232 links in a small footprint. Keep the connector-side routing compact, provide a reliable chassis and signal-ground strategy, and confirm the peripheral's voltage-level and handshake requirements before production release.
Рекомендуется
Embedded UART to Legacy Peripheral Bridge
The MAX3232EIPWRSV bridges a CMOS UART from a controller or microcontroller to a legacy peripheral that exposes only RS-232. Its dual charge-pump circuit generates the bipolar RS-232 levels required by the peripheral while the device continues to operate from a low-voltage supply. A 250 kbps maximum rate supports asynchronous data transfer well beyond the baud rates normally used by legacy peripherals. Use one driver and one receiver for a single-ended link, or use both channels when the peripheral supports two-way control and status signaling.
Рекомендуется
Security and Access-Control Systems
The MAX3232EIPWRSV can serve as the maintenance interface for access-control panels, cameras, or alarm controllers that retain an RS-232 commissioning port. Its plus or minus 15 kV IEC ESD protection is valuable when the connector may be touched by installers or exposed to discharged static, although it does not replace enclosure-level surge protection. The 3 V to 5.5 V supply range simplifies integration with low-voltage controllers, and the dual-channel capability can serve two independent service interfaces. Route the driver outputs directly to the connector and avoid sharing unprotected external traces with sensitive sensor wiring.
Рекомендуется
Data Acquisition and Remote Control Equipment
The MAX3232EIPWRSV supports legacy remote-control and data-acquisition equipment that uses RS-232 for configuration commands or sensor data transfer. At up to 250 kbps, it covers high-speed asynchronous instrument traffic while operating from the same 3 V to 5.5 V supply family used by embedded control hardware. The compact 16-pin SSOP package preserves board area, and the dual architecture can separate control and measurement channels. Verify cable length and grounding at the system level because both affect signal integrity even when the local transceiver meets the specified data rate.
Рекомендуется
Сводка рекомендуемых товаров
Справочные инженерные данные для MAX3232EIPWRSV — сравнение, рекомендации по проектированию и информация о соответствии.
Руководство по выбору
Сравнение с аналогами
| Параметр | Этот товар | MAX3232EIPWV+T | TRS3232EIPWV+T | MAX3243EIPWV+T | TRS3243EIPWV+T | MAX3232 |
|---|---|---|---|---|---|---|
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Package | 16-pin SSOP | 16-pin SSOP | 16-pin SSOP | 16-pin SSOP | 16-pin SSOP | 16-pin SSOP |
| Interface | RS-232 | RS-232 | RS-232 | RS-232 | RS-232 | RS-232 |
| Number of Drivers | 2 | 2 | 2 | 2 | 2 | 2 |
| Number of Receivers | 2 | 2 | 2 | 2 | 2 | 2 |
Ключевые отличия
- Single-supply RS-232 operation simplifies the host power architecture (против MAX3243EIPWV+T)
- Integrated external-terminal ESD protection (против MAX3232)
- Dual-channel interface in a compact surface-mount package (против TRS3232EIPWV+T)
Заметки по проектированию
Place the two charge-pump flying capacitors and the supply bypass capacitor close to the MAX3232EIPWRSV pins shown in the Texas Instruments application circuit. Keep the RS-232 driver outputs and receiver inputs on short, direct routes to the connector. These signals experience larger voltage transitions than the logic side, so separating them from sensitive analog traces reduces capacitive coupling. Maintain the component spacing and capacitor values specified in the manufacturer datasheet rather than substituting larger packages with different parasitics.
Keep the external RS-232 traces away from high-speed clocks and switching-node edges because the bipolar line-driver transitions can couple into nearby circuits. Use a continuous ground reference and route the cable-side ground directly to the connector return. If the cable is externally accessible, retain the transceiver's IEC 61000-4-2 protection rating in the system design and add enclosure or TVS protection when the required surge level exceeds the transceiver's capability.
Do not substitute a MAX3232-family device solely by its driver and receiver count. The MAX3232E and MAX3243E variants use different supply arrangements, while TRS3232E and TRS3243E may require different charge-pump capacitor values or interface details. Compare the exact pin function, package drawing, logic levels, and capacitor network for every revision before releasing a substitution. Also verify DB9 signal names and polarity because connector numbering is not consistent across RS-232 equipment.
The MAX3232EIPWRSV uses slew control on the RS-232 drivers, but the external cable still radiates common-mode energy. Route the two driver outputs as short PCB traces and avoid adding large loops or test pads that increase their effective length. Keep the connector mechanically fixed to the chassis where possible, use a suitable shield or filtered connector for enclosure entry, and maintain a low-impedance return path between the interface ground and the equipment reference network.
Информация о соответствии
The product listing identifies the MAX3232EIPWRSV as RoHS compliant. The Texas Instruments product page identifies plus or minus 15 kV IEC ESD protection and compliance with TIA/EIA-232-F. This RS-232 interface IC is not an automotive-qualified product.