MAX3232EWE-TG068 - 1Mbps RS-232 Transceiver | Analog Devices
MPN: MAX3232EWE-TG068 ✓ فعالMAX3232EWE-TG068 جائزہ
A true RS-232 transceiver is an interface IC that converts logic-level signals into RS-232 voltage levels and converts received RS-232 signals back into logic levels. It belongs to the RS-232 transceiver class, interface IC category, and broader data-conversion and communications-semiconductor hierarchy. Such devices bridge UART, microcontroller, industrial-controller, and data-acquisition equipment across the voltage, noise, and ground-offset differences inherent in RS-232 links.
The principal features of the MAX3232E include a 3.0 V to 5.5 V supply range, operation up to 1 Mbps, and integrated charge-pump circuitry that permits the use of four 0.1 µF capacitors. The 2/2 channel arrangement supports two RS-232 transmit channels and two receive channels in one package. Its 16-pin SOIC format supports conventional surface-mount assembly while conserving board area in compact control and communications equipment.
The MAX3232E architecture is appropriate for systems in which a logic-level UART must communicate with legacy RS-232 peripherals. On-board level translation permits the host side to operate at low digital logic voltages while the cable side uses RS-232 signaling. Charge-pump-assisted drivers produce the required bipolar voltage swings without requiring a separate negative supply. The receiver side restores compatible logic levels while helping the interface withstand the electrical characteristics of a cable-connected RS-232 port.
Typical applications include industrial serial controllers, instrumentation, barcode and identification equipment, point-of-sale terminals, security equipment, and embedded control systems. The 1 Mbps capability is useful for short-distance, higher-speed links where the connected RS-232 equipment supports the same rate. The 3.0 V minimum supply also allows use in modern 3.3 V systems, while the 5.5 V maximum supports conventional 5 V equipment.
PCB implementation requires careful treatment of the charge-pump capacitor network and the RS-232 connector. Place the four 0.1 µF capacitors close to their associated device pins, use a continuous ground plane, and follow the manufacturer datasheet layout to minimize switching noise and capacitor-loop inductance. Confirm the connector's signal and ground assignments before PCB release.
This product summary combines the manufacturer's family specifications, the exact 16-SOIC package identification, lifecycle information, and application-focused guidance. It also distinguishes the readily identifiable same-package replacement from broader functional equivalents so engineers can evaluate board-level compatibility before committing a design to procurement.
کے لیے ڈراپ اِن متبادل MAX3232EWE-TG068 — یکساں پیکیج، پن سے پن مطابقت پذیر۔ مختلف پیکیج والے پرزے جن کے لیے PCB دوبارہ کام درکار ہو، شامل نہیں ہیں۔
MAX3232EWE+
✅ ڈراپ-اِن📋 حوالہ جاتی متبادل (کیٹلاگ میں نہیں)
MAX3232EWE-TG068 تفصیلات
| Product Type | RS-232 transceiver |
| Transceiver Configuration | 2/2 transceiver |
| Supply Voltage Range | 3.0 V to 5.5 V |
| Maximum Data Rate | 1 Mbps |
| Driver Channels | 2 |
| Receiver Channels | 2 |
| Charge-Pump Capacitor Value | 0.1 µF each; four capacitors required |
| پیکیج | 16-pin SOIC |
| ماؤنٹنگ ٹائپ | Surface Mount |
| Product Status | Active |
MAX3232EWE-TG068 پن کنفیگریشن
| پن 1 | C1+ — Charge-pump capacitor 1 positive terminal |
| پن 2 | C1- — Charge-pump capacitor 1 negative terminal |
| پن 3 | V+ — Positive charge-pump output |
| پن 4 | C2+ — Charge-pump capacitor 2 positive terminal |
| پن 5 | C2- — Charge-pump capacitor 2 negative terminal |
| پن 6 | VCC — Positive supply voltage |
| پن 7 | R1OUT — Receiver 1 logic output |
| پن 8 | R2IN — Receiver 2 RS-232 input |
| پن 9 | R2OUT — Receiver 2 logic output |
| پن 10 | R1IN — Receiver 1 RS-232 input |
| پن 11 | V- — Negative charge-pump output |
| پن 12 | T1OUT — Driver 1 RS-232 output |
| پن 13 | T2OUT — Driver 2 RS-232 output |
| پن 14 | T2IN — Driver 2 logic input |
| پن 15 | T1IN — Driver 1 logic input |
| پن 16 | GND — Ground |
عام استعمالات
MAX3232EWE-TG068 کے لیے موزوں ہے 6 ایپلیکیشنs: Industrial Serial Controllers, Point-of-Sale Terminals, Barcode and Identification Equipment, Data-Acquisition Instruments, Security and Access-Control Equipment, Embedded UART-to-RS-232 Bridges.
Industrial Serial Controllers
The MAX3232EWE-TG068 fits industrial controllers that need bidirectional RS-232 connectivity to a host computer, operator panel, or service interface. Its two-driver, two-receiver arrangement supports two communications paths in one 16-pin SOIC, while the 3.0 V to 5.5 V supply range is compatible with common embedded control rails. Operation up to 1 Mbps provides margin for short-distance links, although the connected equipment must support the selected baud rate. Follow the manufacturer layout for the four 0.1 µF charge-pump capacitors, and use a solid ground plane and properly terminated RS-232 connector to reduce noise coupling in industrial enclosures.
تجویز کردہ
Point-of-Sale Terminals
Point-of-sale equipment can use the MAX3232EWE-TG068 to connect a low-voltage controller to a receipt printer, customer display, scanner, or service terminal through RS-232. The integrated level translator converts UART logic to true RS-232 levels without a separate negative supply, while the 3.0 V to 5.5 V operating range supports both 3.3 V and 5 V logic systems. Two transmitters and two receivers permit bidirectional communication on one compact device. Keep the charge-pump capacitors close to their pins and provide a low-impedance chassis or signal-ground return to the connector to maintain reliable operation in retail environments containing motors and switching supplies.
تجویز کردہ
Barcode and Identification Equipment
The MAX3232EWE-TG068 is appropriate for barcode scanners, label printers, and identification subsystems that exchange serial commands with a host controller over RS-232. The 1 Mbps maximum data rate allows short links to operate above common low-speed serial baud rates, while the 2/2 channel arrangement can support separate command and status paths. Its 16-pin SOIC package helps limit board area in compact scanners. Design the PCB with the manufacturer's recommended capacitor placement, maintain a continuous ground plane, and route the RS-232 traces away from switching nodes and high-current return paths to reduce false triggers and command errors.
تجویز کردہ
Data-Acquisition Instruments
Laboratory and industrial data-acquisition instruments can use the MAX3232EWE-TG068 to interface a controller or instrument-control computer with legacy RS-232 sensors and peripheral modules. The true RS-232 level translation allows the logic side to operate from a 3.0 V to 5.5 V supply, and the receiver channels convert incoming cable signals to compatible digital levels. Although the device supports rates up to 1 Mbps, practical instrument links commonly operate at lower baud rates, so configure both endpoints consistently. Use short ground returns, isolated cable routing where required, and the exact four 0.1 µF capacitor connections shown in the manufacturer layout.
تجویز کردہ
Security and Access-Control Equipment
Access-control readers, door controllers, and security peripherals commonly use RS-232 for configuration and diagnostic communication. The MAX3232EWE-TG068 offers two transmit and two receive channels, a 3.0 V minimum supply, and data-rate capability up to 1 Mbps within a compact 16-pin SOIC footprint. Those characteristics support controller boards that need bidirectional communication without a separate negative rail. For deployed equipment, verify the exact suffix temperature range, add connector-level surge protection according to the installation environment, and maintain a continuous ground reference between the logic system and shielded cable. Use the manufacturer's capacitor placement to prevent charge-pump noise from entering sensitive adjacent circuitry.
تجویز کردہ
Embedded UART-to-RS-232 Bridges
The MAX3232EWE-TG068 is useful in embedded UART-to-RS-232 bridge modules for industrial controls, test equipment, and legacy peripheral connectivity. The interface IC translates between low-voltage UART signals and true RS-232 levels, allowing a microcontroller or programmable controller to connect directly to a DB-style or terminal-style connector. Its 3.0 V to 5.5 V supply range supports common embedded rails, and the 2/2 architecture can serve two independent communication directions or channels. Place all four 0.1 µF charge-pump capacitors directly beside the device, preserve uninterrupted ground planes, and follow the manufacturer's pin-specific layout to minimize emissions and improve noise immunity.
تجویز کردہ
تجویز کردہ پروڈکٹس کا خلاصہ
کے لیے انجینئرنگ ریفرنس ڈیٹا MAX3232EWE-TG068 — موازنہ، ڈیزائن رہنمائی، اور تعمیل کی معلومات۔
انتخاب کی گائیڈ
متبادلات کے ساتھ موازنہ
| پیرامیٹر | یہ پروڈکٹ | MAX3232EWE+ |
|---|---|---|
| Brand | Analog Devices | Analog Devices |
| Package | 16-pin SOIC | 16-pin SOIC - same package |
| Product Type | True RS-232 transceiver | 2/2 RS-232 transceiver |
| Supply Voltage Range | 3.0 V to 5.5 V | 3.0 V to 5.5 V |
| Maximum Data Rate | 1 Mbps | 1 Mbps |
| Channel Configuration | 2 drivers and 2 receivers | 2/2 transceiver |
| Charge-Pump Capacitors | Four 0.1 µF capacitors | Four 0.1 µF capacitors |
| Ordering Suffix | MAX3232EWE-TG068 | MAX3232EWE+ |
اہم امتیازی خصوصیات
- Exact TG068 ordering-code availability (بمقابلہMAX3232EWE+)
- Directly identified 16-SOIC replacement path (بمقابلہMAX3232EWE+)
- Single-package dual-channel RS-232 interface (بمقابلہMAX3232EWE+)
ڈیزائن نوٹس
Place all four 0.1 µF charge-pump capacitors directly beside the corresponding MAX3232EWE-TG068 pins, following the manufacturer datasheet layout. Keep each capacitor's connection to its device pin short and use the ground-plane return shown in the reference layout. Long capacitor loops increase charge-pump noise, coupling, and supply disturbance, particularly when the interface operates near the 1 Mbps limit.
Route RS-232 connector traces away from switching-regulator power paths, relay outputs, clocks, and high-current motor returns. Maintain a continuous ground plane under the transceiver where practical, and provide the RS-232 connector ground conductor to the interface ground through a short, low-impedance path. This reduces ground offset and prevents charge-pump or switching noise from appearing as data errors.
Do not treat the MAX3232EWE-TG068 and MAX3232EWE+ ordering codes as automatically interchangeable without checking the temperature-grade and suffix requirements. Both are associated with the 16-SOIC MAX3232E family, but procurement qualifications may differ. Also avoid installing a 5 V-only UART at an unsupported logic level merely because the transceiver supply can reach 5.5 V; confirm the host-side voltage thresholds.
Decouple the device close to VCC and GND with the capacitance and placement specified by the Analog Devices datasheet. The MAX3232 family uses charge-pump circuitry, so bypassing and grounding are essential even though the external capacitors are specified at 0.1 µF. Validate the completed board at the intended 1 Mbps data rate and worst-case supply condition to check that switching activity does not corrupt the attached UART link.
تعمیل کی معلومات
Exact environmental and material compliance claims were not identified for the MAX3232EWE-TG068 ordering code.