MAX350CAP+ - Dual 4:1 Analog Multiplexer | Analog Devices
MPN: MAX350CAP+ ✓ فعالMAX350CAP+ جائزہ
An analog multiplexer is an interface IC that connects multiple signal sources to a shared destination while allowing a controller to select the active path. The MAX350 family belongs to the broader switch and multiplexer hierarchy, where its 4:1 configurations provide four inputs per circuit and reduce the number of external routing connections required in a PCB.
The MAX350CAP+ provides two 4:1 circuits in one package, with maximum on-resistance of 100 ohms. On-resistance matching between switches is specified at 16 ohms maximum, while variation across the specified signal range is limited to 10 ohms maximum. The low-voltage architecture supports dual supplies from ±2.7 V to ±8 V or a single supply from +2 V to +16 V.
Because these are CMOS analog switches, the device conducts equally well in either direction. The serial control interface allows an external controller to select among the four channels in each circuit, reducing the number of parallel logic connections compared with a mechanically switched multiplexer. Charge injection of 1 pC and channel capacitance of 2 pF are useful considerations when precision transient or bandwidth behavior matters.
Typical uses include signal-routing modules, programmable test equipment, industrial control interfaces, data-acquisition systems, and communication equipment. The dual 4:1 arrangement is especially useful where two independent groups of analog inputs must be selected under software control while maintaining a compact 20-pin SSOP footprint.
When assigning PCB tracks, keep protected or high-impedance signal paths short and use the pin-description table in the manufacturer datasheet. Check the actual signal amplitude, bandwidth, supply arrangement, and control-logic levels against the electrical characteristics before treating the 100-ohm maximum on-resistance as acceptable insertion loss.
This page combines manufacturer specifications, sourcing information, compatible family options, and practical interface-design guidance. It also distinguishes verified drop-in options from related MAX349 and MAX350 devices so engineers can select by channel configuration, package, pinout, and supply requirements rather than by multiplexer function alone.
کے لیے ڈراپ اِن متبادل MAX350CAP+ — یکساں پیکیج، پن سے پن مطابقت پذیر۔ مختلف پیکیج والے پرزے جن کے لیے PCB دوبارہ کام درکار ہو، شامل نہیں ہیں۔
اس سیریز میں مختلف ورژن
اسی سیریز کے ماڈلز جو ڈراپ اِن مطابقت رکھتے ہیں MAX350CAP+ (یکساں فارم فیکٹر اور فٹ پرنٹ) — میں مختلف Maximum On-Resistance, Package.
MAX350EWN+
✅ ڈراپ-اِنقیمت کے لیے رابطہ کریں
ڈیٹا شیٹ دیکھیں →MAX350CAP
✅ ڈراپ-اِن📋 حوالہ جاتی متبادل (کیٹلاگ میں نہیں)
MAX350CAP+ تفصیلات
| Product Type | Serially controlled dual 4:1 analog multiplexer |
| Number of Circuits | 2 circuits |
| Multiplexer Configuration | Dual 4:1 |
| Maximum On-Resistance | 100 ohms |
| On-Resistance Matching Between Switches | 16 ohms maximum |
| On-Resistance Flatness Over Signal Range | 10 ohms maximum |
| Signal Conduction Direction | Bidirectional |
| Dual Supply Voltage Range | ±2.7 V to ±8 V |
| Single Supply Voltage Range | +2 V to +16 V |
| Channel Capacitance | 2 pF |
| Charge Injection | 1 pC |
| پیکیج | 20-pin SSOP |
| Control Interface | Serial |
| Technology | CMOS analog switch |
| Manufacturer Lifecycle Status | Production |
MAX350CAP+ 20-pin ssop پن کنفیگریشن گائیڈ
MAX350CAP+ (20-pin ssop پیکیج) کے لیے پن کنفیگریشن۔ پن نمبرنگ، فنکشنز اور کنکشن ڈایاگرامز مینوفیکچرر کے ڈیٹا شیٹ میں بیان کیے گئے ہیں۔ درست فٹ پرنٹ اور سولڈرنگ رہنما ہدایات کے لیے اسی سے رجوع کریں۔
کے لیے تفصیلی پن آؤٹ ڈیٹا دستیاب نہیں MAX350CAP+.
رجوع کریں ڈیٹا شیٹ مکمل پن کنفیگریشن کے لیے۔
عام استعمالات
MAX350CAP+ کے لیے موزوں ہے 6 ایپلیکیشنs: Programmable Test-Signal Routing, Data-Acquisition Signal Multiplexing, Communication Interface Routing, Industrial Control Signal Selection, Medical and Sensor Signal Routing, Programmable Instrumentation and Calibration.
Programmable Test-Signal Routing
The MAX350CAP+ fits programmable test modules that must route several low-level analog sources to a common measurement path. Two independent 4:1 sections allow one group of signals to be selected while another group is handled simultaneously, reducing the number of external relays and routing components. Its maximum on-resistance of 100 ohms is suitable when the source impedance is low and cable or fixture capacitance dominates the bandwidth limitation. Serial control simplifies microcontroller or FPGA-based selection, while bidirectional conduction supports loopback and two-ended instrumentation. The 20-pin SSOP package also keeps the routing section compact, although the final input bandwidth and settling behavior should be verified with the complete test fixture.
تجویز کردہ
Data-Acquisition Signal Multiplexing
The MAX350CAP+ can select among four analog inputs in each of two acquisition channels, allowing multiple sensors or conditioned signals to share ADC front-end circuitry. The dual 4:1 arrangement is useful when two measurement groups must be sampled without duplicating complete analog routing paths. Its 2 pF channel capacitance and 1 pC charge injection are important when the multiplexer sits close to a high-impedance sensor amplifier. The 100-ohm maximum on-resistance should be included in the source-impedance calculation because amplifier bias current can create an additional offset. Serial control reduces parallel control wiring, and the 20-pin SSOP package is practical for compact multi-channel measurement boards.
تجویز کردہ
Communication Interface Routing
The MAX350CAP+ is suitable for low-voltage communication boards that require software-controlled routing among several analog or mixed-signal paths. Bidirectional conduction allows the same switch network to support transmit, receive, or loopback arrangements, and the dual 4:1 configuration provides two independent routing sections within one package. Its maximum on-resistance of 100 ohms can be suitable for low-impedance sensor lines or baseband paths, but it must be checked against line loading and attenuation requirements. Serial addressing minimizes GPIO usage compared with discrete control logic. For higher-speed signals, validate channel capacitance, propagation behavior, and external buffering rather than assuming generic multiplexer functionality guarantees the target bandwidth.
تجویز کردہ
Industrial Control Signal Selection
The MAX350CAP+ can route four control or measurement signals into each of two shared paths in an industrial controller. This arrangement helps designers consolidate field-interface wiring while retaining independent selection for two equipment subsystems. The device supports single-supply operation from +2 V to +16 V as well as dual supplies from ±2.7 V to ±8 V, giving flexibility when the board mixes positive, negative, and ground-referenced signals. Serial control supports deterministic configuration from a microcontroller or embedded controller. Because the on-resistance can reach 100 ohms, verify drive strength at the source and sensitivity at the receiving input, and provide appropriate protection for external industrial wiring.
تجویز کردہ
Medical and Sensor Signal Routing
The MAX350CAP+ can provide compact analog routing for low-level sensor interfaces where multiple conditioned inputs must be selected before amplification. The dual 4:1 organization allows two independent sensor groups to share a limited set of downstream analog channels, while serial control makes the selection sequence easy to coordinate with a sensor controller. Its 2 pF channel capacitance and 1 pC charge injection are relevant to high-impedance front ends, but the complete amplifier topology must be evaluated for offset and transient error. The MAX350CAP+ is not designated as an AEC-Q100 automotive part, and medical suitability must be established at the system level through applicable validation and regulatory procedures.
تجویز کردہ
Programmable Instrumentation and Calibration
The MAX350CAP+ supports compact calibration and instrumentation systems by allowing a controller to select among several reference or stimulus paths. Each 4:1 circuit can present one of four sources to a common destination, making it useful for gain-setting networks, calibration tables, and configurable front ends. Bidirectional conduction also permits source-and-measurement sharing, and the specified 16-ohm maximum matching between switches helps limit channel-to-channel calibration error. The serial control interface reduces the number of discrete select lines. For precision measurements, include the maximum 100-ohm on-resistance, source impedance, injected charge, and switch capacitance in the error budget, and use the manufacturer characterization data for the actual signal range.
تجویز کردہ
تجویز کردہ پروڈکٹس کا خلاصہ
کے لیے انجینئرنگ ریفرنس ڈیٹا MAX350CAP+ — موازنہ، ڈیزائن رہنمائی، اور تعمیل کی معلومات۔
انتخاب کی گائیڈ
متبادلات کے ساتھ موازنہ
| پیرامیٹر | یہ پروڈکٹ | MAX350EWN+ | MAX350CAP |
|---|---|---|---|
| Package | 20-pin SSOP | 20-pin SSOP | 20-pin SSOP |
| Brand | Analog Devices | Analog Devices | Analog Devices |
| Multiplexer Configuration | Dual 4:1 | Dual 4:1 | Dual 4:1 |
| Maximum On-Resistance | 100 ohms | 100 ohms maximum for the MAX350 family | 100 ohms |
| On-Resistance Matching | 16 ohms maximum | 16 ohms maximum for the MAX350 family | 16 ohms maximum |
| On-Resistance Flatness | 10 ohms maximum | 10 ohms maximum for the MAX350 family | 10 ohms maximum |
| Signal Conduction | Bidirectional | Bidirectional | Bidirectional |
| Dual Supply Range | ±2.7 V to ±8 V | ±2.7 V to ±8 V | ±2.7 V to ±8 V |
| Single Supply Range | +2 V to +16 V | +2 V to +16 V | +2 V to +16 V |
| Channel Capacitance | 2 pF | 2 pF | 2 pF |
| Charge Injection | 1 pC | 1 pC | 1 pC |
| Control Interface | Serial | Serial | Serial |
اہم امتیازی خصوصیات
- Two independent 4:1 routing sections in one package (بمقابلہMAX349EAP)
- Low maximum on-resistance with controlled matching (بمقابلہMAX349EAP)
- Bidirectional routing in a compact interface package (بمقابلہMAX349EAP)
ڈیزائن نوٹس
Include the switch's maximum 100-ohm on-resistance, 2 pF channel capacitance, and 1 pC charge injection in the receiver error budget. At high source impedance, the 100-ohm contribution can shift amplifier bias and introduce gain error, while charge injection creates a transient whenever the serial selection changes. Place the MAX350CAP+ near the amplifier input when trace capacitance and switching transients are significant, and use the manufacturer pin-description table when assigning the common and selectable terminals.
Decouple each supply rail close to the MAX350CAP+ with low-inductance ceramic and bulk capacitance selected for the board's supply impedance and switching environment. Keep the analog ground return path continuous and connect it according to the manufacturer package and layout guidance. The device supports single and dual supplies, so do not assume that a grounded common node is electrically interchangeable with a mid-supply reference. Confirm the actual signal range, control thresholds, and absolute voltage limits for the selected supply arrangement.
Route each selected analog channel with a geometry that minimizes coupling to adjacent high-impedance inputs and digital control traces. Maintain short connections between the multiplexer, source, and destination devices, and avoid long parallel runs beneath serial-control nets. Because the device is available in a 20-pin SSOP package, verify courtyard clearance, soldering profile, and exposed lead accessibility during board assembly. Do not infer the complete pin assignment from circuit position; use the pin-description table in the manufacturer datasheet.
تعمیل کی معلومات
The manufacturer product page identifies MAX350 as a production device. Specific RoHS, REACH, AEC-Q100, lead-free, halogen-free, and conflict-minerals declarations require confirmation from the applicable product documentation.