MAX368CWN+ - 8:1 Fault-Protected Analog Multiplexer | Analog Devices
MPN: MAX368CWN+ ✗ اختتامِ زندگیMAX368CWN+ جائزہ
An analog multiplexer is an interface IC that connects multiple signal sources to one shared input on a host circuit. The MAX368CWN+ belongs to the broader multiplexer and demultiplexer hierarchy, where a multiplexer selects among several inputs and a demultiplexer directs one input toward multiple outputs. Its single-ended architecture, 8:1 configuration, and 1.8 kOhm on-resistance make it relevant to compact analog signal-routing systems rather than high-voltage power switching.
The principal documented features include an 8:1 single circuit configuration, 1.8 kOhm on-resistance, and an 18-SOIC package. The MAX368 family is identified as a fault-protected analog multiplexer with latch, allowing a system to place a selected channel into a held state during control or fault-management sequences. Its surface-mount construction supports compact PCB layouts while preserving leaded-component handling characteristics associated with the SOIC form factor.
Technically, the device uses separate selection and enable controls to route one of eight channels to the common output. Because it is intended for analog signals, channel resistance and leakage behavior are important considerations when the source impedance is high. The 1.8 kOhm specification should be compared with the input impedance of the receiving amplifier, ADC, or instrumentation circuit; otherwise, source-loading errors can reduce signal amplitude and disturb the expected transfer function.
Typical uses include sensor-channel selection, test and measurement signal routing, data-acquisition systems, industrial control interfaces, and communication equipment that must connect several low-frequency analog sources to a shared processing channel. The surface-mount 18-SOIC package can also simplify board-level replacement of the non-tape-and-reel MAX368CWN ordering code when the electrical configuration and operating requirements are identical.
PCB design should keep selected and unselected analog paths short, provide a solid ground reference, and isolate sensitive routing from switching or digital clock signals. Because the available device data does not publish a complete pin-description table, engineers should use the manufacturer’s MAX368 datasheet when assigning every physical pin and confirming control polarity, fault behavior, and absolute maximum ratings.
This page combines the verified product identity, package information, ordering-code distinctions, procurement availability, and replacement analysis with practical guidance for selecting and implementing this multiplexer. It is intended to help engineers distinguish the MAX368CWN+ from related MAX368 ordering codes and determine whether a proposed replacement preserves the required 8:1, single-ended, 18-SOIC configuration.
کے لیے ڈراپ اِن متبادل MAX368CWN+ — یکساں پیکیج، پن سے پن مطابقت پذیر۔ مختلف پیکیج والے پرزے جن کے لیے PCB دوبارہ کام درکار ہو، شامل نہیں ہیں۔
MAX368EWN+
✅ ڈراپ-اِن📋 حوالہ جاتی متبادل (کیٹلاگ میں نہیں)
MAX368EWN-T
✅ ڈراپ-اِن📋 حوالہ جاتی متبادل (کیٹلاگ میں نہیں)
MAX368CWN+ تفصیلات
| Product Type | Single-ended analog multiplexer |
| Multiplexer Configuration | 8:1 |
| Number of Circuits | 1 circuit |
| On-Resistance | 1.8 kOhm |
| Signal Architecture | Single-ended |
| Fault Protection | Fault-protected |
| Latch Function | Yes |
| پیکیج | 18-SOIC |
| Package Width | 7.50 mm |
| ماؤنٹنگ ٹائپ | Surface mount |
| Temperature Grade | Commercial |
| Number of Terminals | 16 terminals |
| Package Code | SOP |
| Package Shape | Rectangular |
| Analog Input Channels | 8 channels |
| Common Output Channels | 1 channel |
MAX368CWN+ rectangular پن کنفیگریشن گائیڈ
MAX368CWN+ (rectangular پیکیج) کے لیے پن کنفیگریشن۔ پن نمبرنگ، فنکشنز اور کنکشن ڈایاگرامز مینوفیکچرر کے ڈیٹا شیٹ میں بیان کیے گئے ہیں۔ درست فٹ پرنٹ اور سولڈرنگ رہنما ہدایات کے لیے اسی سے رجوع کریں۔
کے لیے تفصیلی پن آؤٹ ڈیٹا دستیاب نہیں MAX368CWN+.
رجوع کریں ڈیٹا شیٹ مکمل پن کنفیگریشن کے لیے۔
عام استعمالات
MAX368CWN+ کے لیے موزوں ہے 6 ایپلیکیشنs: Multichannel Sensor Acquisition, Data Acquisition Signal Routing, Industrial Control Signal Multiplexing, Test and Measurement Switching, Communication Equipment Analog Routing, Instrumentation and Diagnostic Multiplexing.
Multichannel Sensor Acquisition
MAX368CWN+ is useful when several sensor outputs must feed one amplifier or analog-to-digital converter. Its 8:1 configuration reduces the number of downstream analog inputs, while the 1.8 kOhm on-resistance must be included in the source-impedance calculation. For resistive dividers, sensor outputs, or current-mode sources, verify that the selected channel does not create unacceptable attenuation. Place the multiplexer close to the sensors and acquisition converter, keep the common output path short, and provide a stable ground reference. The single-ended architecture is appropriate when the sensors share a common reference and their signals remain within the electrical limits of the MAX368 family.
تجویز کردہ
Data Acquisition Signal Routing
The MAX368CWN+ can route one of eight analog channels to a shared data-acquisition input, simplifying board routing when the system does not require simultaneous sampling of all channels. The 1.8 kOhm channel resistance should be compared with the source impedance and ADC sampling characteristics to estimate the acquisition error. Because the device is an 8:1 single-ended multiplexer rather than a simultaneous-sampling ADC, the selected source must remain stable during conversion. Short traces, careful grounding, and isolation from digital control signals are essential for preserving measurement accuracy, especially when high-impedance sensors drive the multiplexed inputs.
تجویز کردہ
Industrial Control Signal Multiplexing
MAX368CWN+ fits compact industrial control boards that must select among multiple analog command, feedback, or sensor signals. Its 8:1, single-ended configuration allows one analog processing chain to serve several system channels, reducing component count and PCB area. The commercial-temperature ordering code must be checked against the enclosure temperature and nearby heat sources. Designers should also account for the 1.8 kOhm on-resistance, confirm that control transitions do not create unacceptable settling time, and follow the fault-protection and latch behavior defined by the manufacturer before using the device in safety-related control paths.
تجویز کردہ
Test and Measurement Switching
In a test or measurement system, MAX368CWN+ can connect several test points to a shared measurement amplifier or instrument input. The 8:1 selection supports repeatable routing of control voltages, sensor outputs, or diagnostic nodes while preserving a compact 18-SOIC footprint. Measurement accuracy depends on source impedance, channel resistance, leakage, switching behavior, and the acquisition timing, so those characteristics must be evaluated together. For low-level signals, use guarded grounding and minimize trace length; for higher-bandwidth signals, verify the complete signal path because the published product information does not specify operating bandwidth.
تجویز کردہ
Communication Equipment Analog Routing
MAX368CWN+ can serve as an analog routing element in communication equipment that monitors or conditions several related low-frequency signal sources. Its single-ended 8:1 arrangement is appropriate when channels share a common reference and can be selected sequentially. The 1.8 kOhm on-resistance may be acceptable for impedance-tolerant signal paths but can attenuate high-impedance sources, so amplifier input impedance and source loading must be checked. Control traces should not run parallel to sensitive analog lines, and the common output should be routed directly toward the receiving circuitry to minimize added noise and coupling.
تجویز کردہ
Instrumentation and Diagnostic Multiplexing
The MAX368CWN+ supports instrumentation boards that route diagnostic, feedback, or calibration voltages into a common measurement channel. Eight-to-one selection reduces the number of analog switches and input stages needed when each source can be measured sequentially. Designers should not infer simultaneous sampling, isolation bandwidth, or precision from the multiplexer configuration alone. Confirm the on-resistance variation, leakage, control timing, and fault behavior in the MAX368 manufacturer datasheet. A quiet ground plane and short analog traces are especially important when the selected signal is small relative to the system’s full-scale measurement range.
تجویز کردہ
تجویز کردہ پروڈکٹس کا خلاصہ
کے لیے انجینئرنگ ریفرنس ڈیٹا MAX368CWN+ — موازنہ، ڈیزائن رہنمائی، اور تعمیل کی معلومات۔
انتخاب کی گائیڈ
متبادلات کے ساتھ موازنہ
| پیرامیٹر | یہ پروڈکٹ | MAX368EWN+ | MAX368EWN-T |
|---|---|---|---|
| Brand | Analog Devices | Analog Devices | Analog Devices |
| Package | 18-SOIC | 18-SOIC | 18-SOIC |
| Multiplexer Configuration | 8:1 | 8:1 | 8:1 |
| Number of Circuits | 1 circuit | 1 circuit | 1 circuit |
| Signal Architecture | Single-ended | Single-ended | Single-ended |
| Fault Protection | Fault-protected | Fault-protected | Fault-protected |
| Latch Function | Yes | Yes | Yes |
| Mounting Type | Surface mount | Surface mount | Surface mount |
اہم امتیازی خصوصیات
- Documented 8:1 single-ended routing in an 18-SOIC package (بمقابلہMAX368EWN+)
- Commercial-temperature target ordering code (بمقابلہMAX368EWN+)
- Fault-protected multiplexed analog interface (بمقابلہMAX368EWN-T)
ڈیزائن نوٹس
Treat the MAX368CWN+ as a resistance-bearing analog element. With a documented on-resistance of 1.8 kOhm, a high-impedance sensor can experience meaningful attenuation when the source resistance and receiver input resistance form a divider. Calculate the expected channel gain using the actual source, multiplexer, and receiver impedances, and add margin for on-resistance variation when precision measurements are required.
Route each selected analog channel directly to its destination, and keep the common output trace short and away from digital control lines. Provide a continuous ground reference beneath the analog path, use symmetrical routing where channel matching matters, and avoid long parallel runs with switching signals. These layout practices reduce capacitive pickup and ground-current coupling that can obscure the selected channel.
Do not select a replacement solely because it has an 18-SOIC outline. Verify the 8:1 configuration, single-ended architecture, control logic, latch polarity, fault behavior, electrical ratings, and temperature grade in the manufacturer datasheet. MAX368EWN+ and MAX368EWN-T are documented as consistent alternatives, but their complete operating limits still require confirmation before production substitution.
تعمیل کی معلومات
No specific RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals status was identified for MAX368CWN+ in the available product information. Confirm environmental and quality compliance with Analog Devices using the appropriate MAX368 documentation.