MC33079PG - Quad 16 MHz Low-Noise Op Amp | onsemi
MPN: MC33079PG ✓ فعالMC33079PG جائزہ
An operational amplifier is a voltage-controlled, high-gain differential amplifier used to amplify small input signals and drive higher-level circuits. Within the semiconductor hierarchy, an op amp belongs to the amplifier IC and analog signal-processing categories. The MC33079 combines four amplifiers in one package, reducing board area when a design requires multiple gain stages, buffers, summing amplifiers, or active filters.
The MC33079PG offers a 16 MHz gain-bandwidth product and a 7 V/µs slew rate. These figures make it suitable for audio preamplification, active filtering, signal conditioning, and general instrumentation. High-frequency PNP input transistors are used to obtain low input-voltage noise, while the bipolar process supports operation from single-supply rails beginning at 5 V. The package is a 14-pin PDIP with a 7.62 mm pin pitch.
Its four-amplifier architecture provides a practical way to implement stereo or multichannel signal paths without using four separate packages. When configured with non-inverting gain, the bandwidth depends on the selected feedback components; higher closed-loop gain reduces usable bandwidth. The 7 V/µs slew rate also influences large-signal behavior, so square-wave and high-fidelity audio tests should be evaluated against the intended load and feedback network rather than bandwidth alone.
Typical uses include microphone preamplification, audio mixer stages, active equalization, sensor conditioning, low-frequency active filters, and general-purpose instrumentation. The general-purpose designation indicates that the device is not limited to one application topology. It is especially relevant where several low-noise amplification channels are needed with a shared supply and a conventional through-hole package.
For PCB implementation, maintain short feedback paths and place compensation or filtering components close to the relevant input and output pins. The ±18 V maximum supply rating must include tolerance, transient overshoot, and any rail-to-rail total. Decouple the supply near pin 8 with a short ground return to reduce supply-noise coupling into the four amplifier channels.
This product page combines the manufacturer’s device description with package, electrical, application, lifecycle, and replacement guidance. It also emphasizes the practical distinctions between the MC33079PG and commonly discussed alternatives so that engineers can determine whether the 14-pin PDIP footprint, bipolar input stage, supply range, and 16 MHz bandwidth meet the design requirements before committing to a layout.
کے لیے ڈراپ اِن متبادل MC33079PG — یکساں پیکیج، پن سے پن مطابقت پذیر۔ مختلف پیکیج والے پرزے جن کے لیے PCB دوبارہ کام درکار ہو، شامل نہیں ہیں۔
MC33079P
✅ ڈراپ-اِن📋 حوالہ جاتی متبادل (کیٹلاگ میں نہیں)
MC33079PG زیادہ سے زیادہ ریٹنگز اور برقی خصوصیات
| Number of Amplifiers | 4 circuits |
| Amplifier Type | General purpose |
| Supply Voltage Range | 5 V to 18 V |
| Maximum Supply Voltage | ±18 V |
| Gain-Bandwidth Product | 16 MHz |
| Slew Rate | 7 V/µs |
| Input Transistor Technology | Bipolar high-frequency PNP |
| Process Technology | Bipolar |
| پیکیج | 14-pin PDIP, 7.62 mm pitch |
| ماؤنٹنگ ٹائپ | Through-hole |
| RoHS اسٹیٹس | Compliant |
| Lead-Free Status | Yes |
| Supplier Packaging | Tube |
MC33079PG 14-pin pdip, 7.62 mm pitch پن کنفیگریشن گائیڈ
MC33079PG (14-pin pdip, 7.62 mm pitch پیکیج) کے لیے پن کنفیگریشن۔ اس اینالاگ کمپوننٹ میں اِن پٹ، آؤٹ پٹ اور پاور سپلائی پنز شامل ہیں۔ آفسیٹ نل، کمپنسیشن اور اِن ایبل پن کنفیگریشنز کے لیے مینوفیکچرر کے ڈیٹا شیٹ سے رجوع کریں۔ سگنل کنڈیشننگ اور ایمپلیفائر سرکٹس کے لیے مثالی۔
کے لیے تفصیلی پن آؤٹ ڈیٹا دستیاب نہیں MC33079PG.
رجوع کریں ڈیٹا شیٹ مکمل پن کنفیگریشن کے لیے۔
عام استعمالات
MC33079PG کے لیے موزوں ہے 6 ایپلیکیشنs: Stereo Audio Preamplification, Active Audio Filters, Sensor Signal Conditioning, Industrial Control Signal Conditioning, Test and Measurement Buffering, Audio Mixing and Summing.
Stereo Audio Preamplification
The MC33079PG fits a stereo or multichannel audio preamplifier because four bipolar amplifier channels, a 16 MHz gain-bandwidth product, and a 7 V/µs slew rate are available in one 14-pin PDIP package. The low-noise PNP input stage is appropriate for amplifying microphone-level or line-level signals without adding excessive broadband noise. Place input and feedback resistors close to their associated pins, bypass the supply near pin 8, and keep each feedback loop compact. The actual signal-to-noise performance will also depend on resistor selection, source impedance, closed-loop gain, and grounding.
تجویز کردہ
Active Audio Filters
The MC33079PG can implement multiple active equalization or low-pass filter stages where a compact through-hole solution and audio-band bandwidth are desired. Its 16 MHz gain-bandwidth product leaves substantial margin above audio frequencies, while the 7 V/µs slew rate supports signals well beyond conventional audio bandwidth. Four independent amplifiers allow a stereo filter with one package or a four-channel implementation with two packages. Select resistor and capacitor values for the target cutoff and Q, then verify stability and distortion in the final load configuration.
تجویز کردہ
Sensor Signal Conditioning
The MC33079PG is useful for conditioning low-level sensor signals when the design requires several amplification or buffering channels on a shared 5 V to 18 V supply. The bipolar input stage supports low-noise signal acquisition, and the four-channel package can implement gain, filtering, buffering, and output-drive functions without four separate ICs. For strain, temperature, or bridge-sensor interfaces, choose resistor networks with low excess noise and pay attention to offset, bias current, and common-mode limits. Keep sensitive inputs away from switching nodes and provide a low-impedance reference return.
تجویز کردہ
Industrial Control Signal Conditioning
The MC33079PG can condition control and measurement signals in industrial electronics that use conventional through-hole construction and require four general-purpose amplifier channels. Its 7 V/µs slew rate allows it to process control signals that change faster than static voltage set points, while the 16 MHz gain-bandwidth product supports moderate-bandwidth feedback networks. Include the supply tolerance and transient margin within the ±18 V absolute maximum. Use grounded guard structures, short feedback paths, and solid supply bypassing to prevent switching equipment from coupling noise into precision control loops.
تجویز کردہ
Test and Measurement Buffering
The MC33079PG is appropriate for buffering and gain stages in bench instrumentation, interface boards, and general-purpose measurement systems. Four amplifiers allow source-follower buffers, differential amplifiers, summing networks, and active filters to share one package while operating from a common 5 V to 18 V rail. The bipolar architecture and low-noise input stage help preserve small measured signals, but source impedance and resistor noise can dominate the total error budget. Check output-current demand against the load and avoid using the amplifier as a precision current source.
تجویز کردہ
Audio Mixing and Summing
The MC33079PG is well suited to audio mixing, summing, and distribution circuits because four amplifiers are packaged together and each channel has a 16 MHz gain-bandwidth product. These amplifiers can combine several line-level sources through resistive summing networks, followed by buffering or controlled gain stages. Use the low-frequency bandwidth and slew rate when calculating large-signal behavior, and maintain adequate output headroom on the single-supply rail. The PCB should include a clean analog ground return, local supply bypass, and short routing from each summing node to its input pin.
تجویز کردہ
تجویز کردہ پروڈکٹس کا خلاصہ
کے لیے انجینئرنگ ریفرنس ڈیٹا MC33079PG — موازنہ، ڈیزائن رہنمائی، اور تعمیل کی معلومات۔
انتخاب کی گائیڈ
متبادلات کے ساتھ موازنہ
| پیرامیٹر | یہ پروڈکٹ | MC33079P |
|---|---|---|
| Brand | onsemi | onsemi |
| Package | 14-PDIP, 7.62 mm pitch | 14-PDIP |
| Number of Amplifiers | 4 circuits | 4 circuits |
| Amplifier Type | General purpose | General purpose |
| Supply Voltage Range | 5 V to 18 V | 5 V to 18 V |
| Maximum Supply Voltage | ±18 V | ±18 V |
| Gain-Bandwidth Product | 16 MHz | 16 MHz |
| Slew Rate | 7 V/µs | 7 V/µs |
| Input Stage | Bipolar high-frequency PNP | Bipolar high-frequency PNP |
| Ordering Suffix | G | Non-G ordering code |
اہم امتیازی خصوصیات
- Four low-noise bipolar amplifiers in one through-hole package (بمقابلہOPA1654)
- Directly compatible with the existing MC33079 family PCB design (بمقابلہMC33079P)
- Audio-focused bandwidth and slew-rate combination (بمقابلہOPA1654)
ڈیزائن نوٹس
Place the supply bypass capacitor immediately between the positive supply and ground pins, with its ground connection routed directly to the device ground pin. Keep each amplifier's feedback resistors adjacent to the corresponding output and inverting-input pins to minimize parasitic feedback and oscillation. Sensitive input traces should remain away from supply routing and other high-impedance nodes. Because the MC33079PG uses through-hole leads, maintain adequate spacing for assembly tooling and avoid forcing the package during insertion.
The MC33079PG operates from 5 V to 18 V and has a ±18 V maximum supply rating. Treat the upper operating limit as a design constraint rather than a transient target; include supply tolerance, startup overshoot, and inductive coupling in the worst-case calculation. Decouple the shared supply close to the IC because all four channels draw from it. Verify the output-swing requirements at the actual load, especially near the supply rails, and ensure downstream biasing does not exceed the amplifier output-current capability.
Use a compact analog layout with separate input, feedback, and output regions. Begin each feedback loop at the output pin and route it directly to the inverting-input pin without passing around unrelated channels. Place input biasing and compensation networks close to the associated amplifier. The 14-pin PDIP footprint also requires adequate board-edge clearance and through-hole alignment; inspect the package drawing before defining the footprint because exposed-pad and DIP packages are not interchangeable.
Do not treat the OPA1654 or OPA1644A as direct PCB drop-ins for the MC33079PG. The MC33079PG uses a 14-pin PDIP footprint, while the discussed OPA1654 is offered in a 14-pin surface-mount package, and their input stages have different bias-current and power characteristics. Likewise, confirm the exact input, output, supply, and offset pin assignments before fitting any MC33079 family ordering code. Review the manufacturer pin-connection diagram during schematic capture and compare it mechanically with the assembled board.
تعمیل کی معلومات
The component record identifies MC33079PG as RoHS-compliant, lead-free, and green. No separate REACH, halogen-free, conflict-minerals, or automotive qualification declaration is identified.