onsemi

MC33079PG - Quad 16 MHz Low-Noise Op Amp | onsemi

부품 번호: MC33079PG ✓ 활성
5 V to 18 V Vdss 14-pin PDIP, 7.62 mm pitch Package
MOQ: 1 |

MC33079PG 개요

The onsemi MC33079PG is a low-noise, general-purpose quad operational amplifier fabricated with bipolar technology and optimized for audio and data-signal processing. The device contains four amplifiers in a 14-pin PDIP package and operates from a 5 V to 18 V supply. Its headline specifications include a 16 MHz gain-bandwidth product, a 7 V/µs slew rate, and low-noise bipolar input stages using high-frequency PNP input transistors.

An operational amplifier is a voltage-controlled, high-gain differential amplifier used to amplify small input signals and drive higher-level circuits. Within the semiconductor hierarchy, an op amp belongs to the amplifier IC and analog signal-processing categories. The MC33079 combines four amplifiers in one package, reducing board area when a design requires multiple gain stages, buffers, summing amplifiers, or active filters.

The MC33079PG offers a 16 MHz gain-bandwidth product and a 7 V/µs slew rate. These figures make it suitable for audio preamplification, active filtering, signal conditioning, and general instrumentation. High-frequency PNP input transistors are used to obtain low input-voltage noise, while the bipolar process supports operation from single-supply rails beginning at 5 V. The package is a 14-pin PDIP with a 7.62 mm pin pitch.

Its four-amplifier architecture provides a practical way to implement stereo or multichannel signal paths without using four separate packages. When configured with non-inverting gain, the bandwidth depends on the selected feedback components; higher closed-loop gain reduces usable bandwidth. The 7 V/µs slew rate also influences large-signal behavior, so square-wave and high-fidelity audio tests should be evaluated against the intended load and feedback network rather than bandwidth alone.

Typical uses include microphone preamplification, audio mixer stages, active equalization, sensor conditioning, low-frequency active filters, and general-purpose instrumentation. The general-purpose designation indicates that the device is not limited to one application topology. It is especially relevant where several low-noise amplification channels are needed with a shared supply and a conventional through-hole package.

For PCB implementation, maintain short feedback paths and place compensation or filtering components close to the relevant input and output pins. The ±18 V maximum supply rating must include tolerance, transient overshoot, and any rail-to-rail total. Decouple the supply near pin 8 with a short ground return to reduce supply-noise coupling into the four amplifier channels.

This product page combines the manufacturer’s device description with package, electrical, application, lifecycle, and replacement guidance. It also emphasizes the practical distinctions between the MC33079PG and commonly discussed alternatives so that engineers can determine whether the 14-pin PDIP footprint, bipolar input stage, supply range, and 16 MHz bandwidth meet the design requirements before committing to a layout.

드롭인 대체품: MC33079PG — 동일 패키지, 핀 호환. PCB 재작업이 필요한 다른 패키지 부품은 제외됩니다.

MC33079P

✅ 드롭인
📦 14-PDIP
MC33079P is the same-family 14-PDIP bipolar quad amplifier without the MC33079PG G ordering suffix; core electrical ratings are unchanged, while lead-free procurement status must be confirmed

📋 참조 대체품 (카탈로그에 없음)

MC33079PG 최대 정격 & 전기적 특성

Number of Amplifiers 4 circuits
Amplifier Type General purpose
Supply Voltage Range 5 V to 18 V
Maximum Supply Voltage ±18 V
Gain-Bandwidth Product 16 MHz
Slew Rate 7 V/µs
Input Transistor Technology Bipolar high-frequency PNP
Process Technology Bipolar
패키지 14-pin PDIP, 7.62 mm pitch
실장 유형 Through-hole
RoHS 상태 Compliant
Lead-Free Status Yes
Supplier Packaging Tube

MC33079PG 14-pin pdip, 7.62 mm pitch 핀 구성 가이드

MC33079PG(14-pin pdip, 7.62 mm pitch 패키지)의 핀 구성입니다. 이 아날로그 부품에는 입력, 출력, 전원 공급 핀이 있습니다. 오프셋 널, 보상, 인에이블 핀 구성은 제조사 데이터시트를 참조하십시오. 신호 컨디셔닝 및 증폭기 회로에 이상적입니다.

MC33079PG의 14-pin pdip, 7.62 mm pitch 패키지 핀아웃 다이어그램

다음에 대한 상세 핀아웃 데이터 없음: MC33079PG.

다음을 참조하십시오: 데이터시트 전체 핀 구성은 다음을 참조하십시오.

일반적인 애플리케이션

MC33079PG 적합 용도: 6 애플리케이션s: Stereo Audio Preamplification, Active Audio Filters, Sensor Signal Conditioning, Industrial Control Signal Conditioning, Test and Measurement Buffering, Audio Mixing and Summing.

🎧

Stereo Audio Preamplification

The MC33079PG fits a stereo or multichannel audio preamplifier because four bipolar amplifier channels, a 16 MHz gain-bandwidth product, and a 7 V/µs slew rate are available in one 14-pin PDIP package. The low-noise PNP input stage is appropriate for amplifying microphone-level or line-level signals without adding excessive broadband noise. Place input and feedback resistors close to their associated pins, bypass the supply near pin 8, and keep each feedback loop compact. The actual signal-to-noise performance will also depend on resistor selection, source impedance, closed-loop gain, and grounding.

🎧

Active Audio Filters

The MC33079PG can implement multiple active equalization or low-pass filter stages where a compact through-hole solution and audio-band bandwidth are desired. Its 16 MHz gain-bandwidth product leaves substantial margin above audio frequencies, while the 7 V/µs slew rate supports signals well beyond conventional audio bandwidth. Four independent amplifiers allow a stereo filter with one package or a four-channel implementation with two packages. Select resistor and capacitor values for the target cutoff and Q, then verify stability and distortion in the final load configuration.

🧩

Sensor Signal Conditioning

The MC33079PG is useful for conditioning low-level sensor signals when the design requires several amplification or buffering channels on a shared 5 V to 18 V supply. The bipolar input stage supports low-noise signal acquisition, and the four-channel package can implement gain, filtering, buffering, and output-drive functions without four separate ICs. For strain, temperature, or bridge-sensor interfaces, choose resistor networks with low excess noise and pay attention to offset, bias current, and common-mode limits. Keep sensitive inputs away from switching nodes and provide a low-impedance reference return.

🏭

Industrial Control Signal Conditioning

The MC33079PG can condition control and measurement signals in industrial electronics that use conventional through-hole construction and require four general-purpose amplifier channels. Its 7 V/µs slew rate allows it to process control signals that change faster than static voltage set points, while the 16 MHz gain-bandwidth product supports moderate-bandwidth feedback networks. Include the supply tolerance and transient margin within the ±18 V absolute maximum. Use grounded guard structures, short feedback paths, and solid supply bypassing to prevent switching equipment from coupling noise into precision control loops.

🔧

Test and Measurement Buffering

The MC33079PG is appropriate for buffering and gain stages in bench instrumentation, interface boards, and general-purpose measurement systems. Four amplifiers allow source-follower buffers, differential amplifiers, summing networks, and active filters to share one package while operating from a common 5 V to 18 V rail. The bipolar architecture and low-noise input stage help preserve small measured signals, but source impedance and resistor noise can dominate the total error budget. Check output-current demand against the load and avoid using the amplifier as a precision current source.

🎧

Audio Mixing and Summing

The MC33079PG is well suited to audio mixing, summing, and distribution circuits because four amplifiers are packaged together and each channel has a 16 MHz gain-bandwidth product. These amplifiers can combine several line-level sources through resistive summing networks, followed by buffering or controlled gain stages. Use the low-frequency bandwidth and slew rate when calculating large-signal behavior, and maintain adequate output headroom on the single-supply rail. The PCB should include a clean analog ground return, local supply bypass, and short routing from each summing node to its input pin.

추천 제품 요약

MC33079P Same-family quad audio amplifier 사용처: Stereo Audio Preamplification, Active Audio Filters, Sensor Signal Conditioning, Industrial Control Signal Conditioning, Test and Measurement Buffering OPA1654 Surface-mount JFET-input comparison design 사용처: Audio Mixing and Summing
What is the MC33079PG?
The MC33079PG is a four-amplifier, bipolar general-purpose operational amplifier from onsemi, intended for audio and data-signal processing. According to the onsemi MC33079 product page, the device uses high-frequency PNP input transistors to achieve low input-voltage noise and high gain bandwidth. It operates from a 5 V to 18 V supply and is packaged in a 14-pin PDIP. The quad configuration lets one device provide four independent amplifier channels for preamplifiers, filters, buffers, or instrumentation circuits.
What are the key specifications of MC33079PG that engineers should know?
The MC33079PG combines four general-purpose bipolar amplifiers, a 16 MHz gain-bandwidth product, a 7 V/µs slew rate, and a 5 V to 18 V operating supply range in a 14-pin PDIP package. The onsemi product description identifies high-frequency PNP input transistors as the basis for its low-noise operation. These parameters make the device relevant to audio preamplification, active filtering, sensor signal conditioning, and multichannel analog circuits. Actual noise, offset, bias-current, and temperature limits should be checked against the manufacturer datasheet for production design.
Where can I download the MC33079PG datasheet PDF?
The official MC33079 documentation is available from the onsemi MC33079 product page, which provides the manufacturer’s device description and links to supporting documents. A separately indexed MC33079P datasheet PDF is also listed at AllDatasheet, where the document is identified as 14 pages. Use the onsemi page as the primary source for revisions and ordering information, and consult the MC33079P PDF when it is explicitly identified as the document for the MC33079 family. Verify the package and suffix before releasing production files.
Where can I find the MC33079PG pinout?
The MC33079PG uses a 14-pin PDIP package, and its pin assignments are shown in the pin-connection section of the manufacturer’s MC33079 family datasheet. Do not infer the connections from a generic quad-op-amp drawing because output offsets, supply pins, and input assignments must match the exact device. The onsemi product page is the appropriate starting point for the current family documentation. When laying out the PCB, follow the numbered pins in the datasheet and preserve adequate spacing between adjacent DIP leads.
Where can I buy MC33079PG online?
Use the Request a Quote form on this page to ask for MC33079PG availability, current lead time, and the quantity needed for your build. The MC33079PG is identified as a 14-PDIP quad operational amplifier, and catalog listings indicate tube packaging. A purchasing request should state the required quantity, shipment destination, and whether multiple date codes are acceptable. This avoids committing to an obsolete stock or damaged through-hole inventory when a new tube is required.
What is the price of MC33079PG?
Use the Request a Quote form on this page for the current MC33079PG price and volume breaks. The commercial listing confirms that MC33079PG is the onsemi quad general-purpose amplifier in a 14-PDIP package, but no qualifying quantity-price schedule is displayed here. A quote request can specify the required tube quantity, target shipment date, and acceptable delivery terms so that purchasing can respond with an actionable offer.
What is the lead time for MC33079PG?
Submit an MC33079PG Request a Quote with your required quantity and target delivery date to obtain the current lead-time confirmation. The catalog record identifies the device as a 14-PDIP quad amplifier, while separate packaging information identifies tube delivery. The manufacturing schedule can vary with order quantity and inventory, so an engineer should reserve enough schedule time for a new production run rather than relying on incidental through-hole stock. The quote response should state the confirmed manufacturing and shipment timing.
Is MC33079PG in stock?
Stock status for MC33079PG should be confirmed through the Request a Quote form on this page. The part is actively presented in current component catalogs as an onsemi 14-PDIP quad operational amplifier, but a catalog listing alone does not confirm the quantity, date code, or condition of every available unit. State your required tube quantity and whether substitutions within the same ordering code are acceptable. Purchasing can then respond with a specific inventory and delivery commitment.
What can replace MC33079PG?
MC33079P is the closest documented same-family drop-in candidate because it belongs to the MC33079 quad bipolar amplifier family and uses the 14-pin PDIP configuration; the G ordering suffix identifies the lead-free MC33079PG version. OPA1654 and OPA1644A can provide different input-stage characteristics, but the OPA1654 is not a direct footprint replacement because it is offered in a 14-pin surface-mount package. Confirm the original PCB footprint, supply range, noise requirements, and output-load compatibility before changing the assembled device.
Is MC33079PG the same as OPA1654?
No, the MC33079PG and OPA1654 are not identical drop-in devices. The MC33079PG is a bipolar quad amplifier in a 14-pin PDIP package, while the OPA1654 is a newer JFET-input amplifier offered in 14-pin surface-mount packages. Their input bias current, noise behavior, distortion characteristics, power consumption, and package footprint differ. The OPA1654 may be attractive for a redesigned board, but an existing MC33079PG PDIP footprint cannot accept it without an adapter and careful electrical review.
MC33079PG vs MC33079P - which is better for an existing PDIP design?
Choose the MC33079PG for a new lead-free assembly and MC33079P when the original non-G ordering code is explicitly required by an approved bill of materials. Both identifiers belong to the MC33079 family and describe the 14-pin PDIP quad bipolar amplifier, so the electrical function and circuit role are closely matched. The principal selection issue is ordering code and environmental sourcing rather than a different amplifier topology. Review the manufacturer ordering table and your assembly requirements before making the substitution.
MC33079PG vs OPA1654 - which is better for low-noise audio?
The MC33079PG is preferable when the existing board requires a 14-pin PDIP footprint and a bipolar low-noise amplifier; the OPA1654 requires a different package and offers JFET inputs. For a newly designed surface-mount audio board, the OPA1654 may be considered because of its newer architecture and reported lower input bias current, but its distortion, noise, supply, and power-consumption behavior must be compared with the MC33079PG using the actual signal chain. The package mismatch means the OPA1654 is a redesign option rather than a direct replacement.
When should I choose MC33079PG over a dual operational amplifier?
Choose the MC33079PG when the circuit needs four independent amplification channels and benefits from consolidating them into one 14-pin PDIP package. A dual amplifier is appropriate when only two channels are required, when the PCB has space for separate packages, or when channel-specific shutdown and layout isolation are needed. The MC33079PG provides four general-purpose bipolar amplifiers with a 16 MHz gain-bandwidth product and 7 V/µs slew rate. Confirm that one shared package layout satisfies the required isolation, heat dissipation, and channel-count requirements.
Is MC33079PG suitable for audio preamplifier applications?
Yes, the MC33079PG is suitable for general-purpose audio preamplification because onsemi identifies low-noise bipolar operation and high-frequency PNP input transistors as core features of the MC33079 family. Its 16 MHz gain-bandwidth product and 7 V/µs slew rate provide useful bandwidth for audio-band gain stages, while four channels can implement stereo or multichannel processing. Actual signal quality also depends on the chosen closed-loop gain, resistor noise, supply decoupling, load impedance, and the output-stage operating range.
Does MC33079PG comply with RoHS and lead-free requirements?
The MC33079PG is identified as a RoHS-compliant, lead-free, green component in its component record. It uses a through-hole PDIP package and is listed with tube packaging, which can simplify procurement for conventional through-hole production. Compliance for a finished product also depends on soldering materials, board finish, selected assemblies, and the applicable regional substance declarations. Retain the manufacturer declaration and your assembly BOM records for formal environmental certification or customer audits.

엔지니어링 참조 데이터: MC33079PG — 비교, 설계 지침 및 규정 준수 정보.

선택 가이드

Choose the MC33079PG for a new through-hole design that needs four general-purpose, low-noise bipolar amplifiers from one 14-pin PDIP package. It is particularly suitable for audio preamplification, active filtering, summing stages, sensor conditioning, and instrumentation. Choose MC33079P when an approved legacy bill of materials calls for the non-G ordering code and lead-free procurement is not required. The OPA1654 can be attractive for a newly redesigned surface-mount audio board because it uses a newer JFET input stage, but it is not a footprint-compatible replacement for the MC33079PG. The MC33079DT comparison also fails the package requirement because it is a surface-mount ordering option. Before selecting any replacement, verify the exact pin assignments, supply range, closed-loop stability, output swing, input offset, bias current, and noise requirements against the original circuit.

대체품과의 비교

파라미터 이 제품 MC33079P
Brand onsemi onsemi
Package 14-PDIP, 7.62 mm pitch 14-PDIP
Number of Amplifiers 4 circuits 4 circuits
Amplifier Type General purpose General purpose
Supply Voltage Range 5 V to 18 V 5 V to 18 V
Maximum Supply Voltage ±18 V ±18 V
Gain-Bandwidth Product 16 MHz 16 MHz
Slew Rate 7 V/µs 7 V/µs
Input Stage Bipolar high-frequency PNP Bipolar high-frequency PNP
Ordering Suffix G Non-G ordering code

주요 차별점

  • Four low-noise bipolar amplifiers in one through-hole package (vs OPA1654)
  • Directly compatible with the existing MC33079 family PCB design (vs MC33079P)
  • Audio-focused bandwidth and slew-rate combination (vs OPA1654)

설계 노트

Place the supply bypass capacitor immediately between the positive supply and ground pins, with its ground connection routed directly to the device ground pin. Keep each amplifier's feedback resistors adjacent to the corresponding output and inverting-input pins to minimize parasitic feedback and oscillation. Sensitive input traces should remain away from supply routing and other high-impedance nodes. Because the MC33079PG uses through-hole leads, maintain adequate spacing for assembly tooling and avoid forcing the package during insertion.

The MC33079PG operates from 5 V to 18 V and has a ±18 V maximum supply rating. Treat the upper operating limit as a design constraint rather than a transient target; include supply tolerance, startup overshoot, and inductive coupling in the worst-case calculation. Decouple the shared supply close to the IC because all four channels draw from it. Verify the output-swing requirements at the actual load, especially near the supply rails, and ensure downstream biasing does not exceed the amplifier output-current capability.

Use a compact analog layout with separate input, feedback, and output regions. Begin each feedback loop at the output pin and route it directly to the inverting-input pin without passing around unrelated channels. Place input biasing and compensation networks close to the associated amplifier. The 14-pin PDIP footprint also requires adequate board-edge clearance and through-hole alignment; inspect the package drawing before defining the footprint because exposed-pad and DIP packages are not interchangeable.

Do not treat the OPA1654 or OPA1644A as direct PCB drop-ins for the MC33079PG. The MC33079PG uses a 14-pin PDIP footprint, while the discussed OPA1654 is offered in a 14-pin surface-mount package, and their input stages have different bias-current and power characteristics. Likewise, confirm the exact input, output, supply, and offset pin assignments before fitting any MC33079 family ordering code. Review the manufacturer pin-connection diagram during schematic capture and compare it mechanically with the assembled board.

규정 준수 정보

RoHS
Compliant
REACH
Unknown
AEC-Q100
Not Applicable
무연
Yes
무할로겐
Unknown
분쟁 광물
Unknown

The component record identifies MC33079PG as RoHS-compliant, lead-free, and green. No separate REACH, halogen-free, conflict-minerals, or automotive qualification declaration is identified.

데이터 검증일: 2026-11-16 — XAIPART 부품 엔지니어링 팀이 검증하고 관리한 데이터

관련 검색

MC33079PG datasheet MC33079PG pinout MC33079PG datasheet pdf MC33079PG DIP14 amplifier MC33079PG 16MHz op amp MC33079PG 7V/us slew rate onsemi MC33079PG MC33079PG audio preamplifier MC33079PG active filter MC33079PG equivalent MC33079PG replacement MC33079PG vs OPA1654 MC33079PG price MC33079PG stock

관련 부품 & 용어

onsemi MC33079PG MC33079P MC33079DT OPA1654 OPA1644A quad operational amplifier operational amplifier amplifier IC analog signal processing bipolar operational amplifier low-dropout regulator low-noise amplifier PNP input transistor gain-bandwidth product slew rate audio preamplifier active filter sensor signal conditioning 14-PDIP DIP package through-hole package 14-pin PDIP RoHS lead-free electronics
빠른 견적 RFQ
상세 정보를 모두 입력하십시오 — 영업팀이 24시간 이내에 답변드립니다
부품 번호 제조사 패키지 QTY 목표 가격 합계
✓
견적이 제출되었습니다!

24시간 이내에 이메일로 답변드리겠습니다

1
RFQ 제출됨
2
견적 접수됨
3
주문 완료
4
결제
5
배송됨
6
배송 완료
RFQ 상세 보기