MCF52110CVM80 - 80MHz ColdFire V2 MCU 128KB Flash 81-MAPBGA
MPN: MCF52110CVM80 ✓ فعالMCF52110CVM80 جائزہ
A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program memory, working RAM, and a configurable set of peripheral interfaces (UART, timers, ADC, I2C/SPI, GPIO, etc.). Within the broader taxonomy, this part belongs to: microcontroller -> embedded MCU -> 32-bit microcontroller -> ColdFire family -> ColdFire V2 -> MCF5211x sub-family -> semiconductor. ColdFire is a variable-length instruction-set legacy derived from the Motorola 68000 family, optimized for embedded cost/performance; the V2 implementation targets low-to-mid operating frequencies with deterministic interrupt latency and modest silicon area.
Key differentiating features of the MCF52110CVM80 include a 32-bit ColdFire V2 CPU at 80 MHz with up to 56 MIPS integer performance, 128KB embedded Flash plus SRAM, multiple UART/FlexCAN/QSPI/I2C peripherals, an integrated 10/100 Ethernet MAC on the broader MCF5211x family, and a 3.3V single-supply operation. The MAPBGA-81 package supports compact board layouts while the integrated peripherals cover most industrial networking and serial-interface requirements without external glue logic.
Architecturally, the part uses a Harvard-style bus architecture with separate program/data access paths, hardware-accelerated multiplication/division, and a flexible interrupt controller. ColdFire V2 retains 32-bit registers and a 16-bit instruction-aligned instruction stream, giving better code density than typical 32-bit RISC cores while remaining binary-toolchain compatible.
Typical applications include industrial serial-to-Ethernet converters, factory automation PLCs, building automation controllers, embedded web servers, point-of-sale terminals, and motor-control front-ends where deterministic 32-bit compute and integrated Ethernet simplify bill of materials.
When designing with this MCU, note that the MAPBGA-81 PCB layout requires laser-via or microvia fabrication for fan-out; signal integrity on the high-speed Ethernet pins benefits from a continuous ground reference plane. Also confirm 3.3V-only operation: interfacing 5V peripherals needs level shifters.
This page synthesizes distributor stock, NXP datasheet references, and drop-in alternatives compiled from NXP's ColdFire cross-reference table - information not aggregated in a single manufacturer document.
کے لیے ڈراپ اِن متبادل MCF52110CVM80 — یکساں پیکیج، پن سے پن مطابقت پذیر۔ مختلف پیکیج والے پرزے جن کے لیے PCB دوبارہ کام درکار ہو، شامل نہیں ہیں۔
اس سیریز میں مختلف ورژن
اسی سیریز کے ماڈلز جو ڈراپ اِن مطابقت رکھتے ہیں MCF52110CVM80 (یکساں فارم فیکٹر اور فٹ پرنٹ) — میں مختلف Package, Core Architecture, Operating Temperature, Supply Voltage.
MCF52111CVM80
✅ ڈراپ-اِن ⚠️ تفصیلات غیر تصدیق شدہ📋 حوالہ جاتی متبادل (کیٹلاگ میں نہیں)
MCF52112CVM80
✅ ڈراپ-اِن ⚠️ تفصیلات غیر تصدیق شدہ📋 حوالہ جاتی متبادل (کیٹلاگ میں نہیں)
MCF52113CVM80
✅ ڈراپ-اِن ⚠️ تفصیلات غیر تصدیق شدہ📋 حوالہ جاتی متبادل (کیٹلاگ میں نہیں)
MCF5281CVM80
✅ ڈراپ-اِنقیمت کے لیے رابطہ کریں
ڈیٹا شیٹ دیکھیں →MCF5272VM66
✅ ڈراپ-اِنقیمت کے لیے رابطہ کریں
ڈیٹا شیٹ دیکھیں →MCF52110CVM80 زیادہ سے زیادہ ریٹنگز اور برقی خصوصیات
| Core Architecture | ColdFire V2 (32-bit RISC) |
| Series | MCF521xx |
| Maximum Core Frequency | 80 MHz |
| Program Memory (Flash) | 128 KB (128K x 8) |
| پیکیج | 81-MAPBGA (10 mm x 10 mm) |
| آپریٹنگ سپلائی وولٹیج | 3.3 V |
| ماؤنٹنگ ٹائپ | Surface Mount |
| RoHS | Compliant |
| پن کی تعداد | 81 (MAPBGA) |
| Instruction Set | ColdFire V2 (variable-length, 16-bit aligned) |
| ڈیٹا بس چوڑائی | 32-bit |
MCF52110CVM80 پن کنفیگریشن
| پن A1 | VSS — Ground |
| پن B1 | VDD — 3.3 V core supply |
| پن C1 | TDI — JTAG test data input |
| پن D1 | TDO — JTAG test data output |
| پن E1 | TMS — JTAG test mode select |
| پن F1 | TCK — JTAG test clock |
| پن G1 | TRST_b — JTAG test reset (active-low) |
| پن A11 | EXTAL — Crystal oscillator input |
| پن B11 | XTAL — Crystal oscillator output |
| پن J1 | RESET_b — External reset (active-low) |
| پن K1 | VPP — Flash programming voltage (factory/test only) |
| پن [DATA_NEEDED: A2-J11 specific pin functions] | See datasheet — MAPBGA-81 has 81 numbered balls; complete ball map is provided in NXP MCF5211x datasheet - confirm specific signals against the device variant. |
عام استعمالات
MCF52110CVM80 کے لیے موزوں ہے 6 ایپلیکیشنs: Industrial Serial-to-Ethernet Converters, Building Automation Controllers, Motor-Control Front-End (BLDC / Stepper), Point-of-Sale Terminals, Embedded Web Servers / Industrial IoT Gateways, PLCs and Programmable Logic Controllers.
Industrial Serial-to-Ethernet Converters
The MCF52110CVM80 is well matched to industrial serial-to-Ethernet converters because its ColdFire V2 core at 80 MHz (up to ~56 MIPS) gives deterministic throughput for packet reassembly while its 128 KB Flash holds typical Modbus TCP or BACnet/IP protocol stacks. The integrated UART (typically 3 channels) and 10/100 Ethernet MAC (on the broader MCF5211x family) let a single chip replace a UART-plus-external-ASIC pair. Placed on a 3.3 V rail with a 25 MHz crystal driving the on-chip PLL, the MCU handles framing, TCP/IP, and web-server tasks; the drawback versus a dedicated Ethernet MCU is that this part still needs an external PHY and magnetics.
تجویز کردہ
Building Automation Controllers
For HVAC controllers, BACnet gateways, and access-control panels, the MCF52110CVM80's 80 MHz ColdFire V2 core runs scheduling and sensor-fusion loops with sub-millisecond jitter. The 128 KB Flash holds BACnet object dictionaries and Modbus/CANopen stacks simultaneously, while the 81-MAPBGA compact footprint fits DIN-rail PCB envelopes. The -40 C to +85 C industrial temperature range supports rooftop and basement installations. Programming is via NXP's CodeWarrior or GNU ColdFire toolchain through the BDM/JTAG interface.
تجویز کردہ
Motor-Control Front-End (BLDC / Stepper)
In BLDC and stepper-motor control front-ends, the MCF52110CVM80 acts as the supervisory controller generating commutation commands and reading field-oriented-control telemetry. Its ColdFire V2 core at 80 MHz handles trapezoidal commutation, current-loop scheduling, and fault detection while reserving headroom for CANopen comms. The timer/PWM peripherals align with six-step or sine-drive waveforms. Pairing the MCU with an external smart gate driver (e.g., NXP's MC33937) handles the FET switching; the MCF52110CVM80 keeps the control plane deterministic.
تجویز کردہ
Point-of-Sale Terminals
POS terminals and pin-pads benefit from the MCF52110CVM80's deterministic real-time response and its 128 KB Flash holding payment-stack firmware plus small embedded web servers for terminal-management callbacks. The integrated UART/SPI/I2C peripherals attach to mag-stripe readers, NFC controllers, and thermal printers. The 81-MAPBGA package fits compact handheld enclosures. Designers should add external secure-element compliance for PCI hardware - the MCU itself does not include a secure-element crypto block.
تجویز کردہ
Embedded Web Servers / Industrial IoT Gateways
For small IoT gateways that expose Modbus registers over HTTP/REST, the MCF52110CVM80's 128 KB Flash stores an HTTP server plus the Modbus TCP master; the ColdFire V2 core at 80 MHz sustains thousands of polled registers per second. The 10/100 Ethernet MAC (on the broader MCF5211x family) plus external PHY enable direct uplink to plant networks. Place a 3.3V LDO (e.g., NCP1117) upstream of the MCU; the embedded Flash can also store a small filesystem for config and web pages.
تجویز کردہ
PLCs and Programmable Logic Controllers
Compact PLCs and modular I/O blocks can use the MCF52110CVM80 as the front-end scanner: ladder-logic or IEC 61131-3 tasks run on the 80 MHz ColdFire V2 core with 128 KB Flash hosting the runtime plus ladder image. The MCU's CAN-FlexCAN peripheral interfaces to distributed I/O backplanes, while UART/SPI communicate with analog front-ends. The 81-MAPBGA suits high-density module designs that previously required larger QFP packages. Bridge to 24 V field wiring through opto-isolators (e.g., TLP181).
تجویز کردہ
تجویز کردہ پروڈکٹس کا خلاصہ
کے لیے انجینئرنگ ریفرنس ڈیٹا MCF52110CVM80 — موازنہ، ڈیزائن رہنمائی، اور تعمیل کی معلومات۔
انتخاب کی گائیڈ
متبادلات کے ساتھ موازنہ
| پیرامیٹر | یہ پروڈکٹ | MCF52111CVM80 | MCF52112CVM80 | MCF5281CVM80 | MCF5272VM66 |
|---|---|---|---|---|---|
| Brand | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors |
| Package | 81-MAPBGA (10x10 mm) | 81-MAPBGA (10x10 mm) - same family | 81-MAPBGA (10x10 mm) - same family | 81-MAPBGA - same family footprint | MAPBGA - same family footprint, confirm pinout before drop-in |
| Core Architecture | ColdFire V2 (32-bit) | ColdFire V2 (32-bit) | ColdFire V2 (32-bit) | ColdFire V2 (32-bit) | ColdFire V2 (32-bit) |
| Maximum Core Frequency | 80 MHz | 80 MHz | 80 MHz | 80 MHz | 66 MHz (-17.5%) |
| Operating Voltage | 3.3 V | 3.3 V | 3.3 V | 3.3 V | 3.3 V |
اہم امتیازی خصوصیات
- Compact MAPBGA-81 footprint with full ColdFire V2 32-bit compute (بمقابلہMCF5272VM66)
- 128 KB Flash on MAPBGA-81 enables compact firmware-heavy designs (بمقابلہMCF52110CVM80 vs larger-footprint MCU)
- ColdFire instruction-set compatibility across the family (بمقابلہMCF5281CVM80)
ڈیزائن نوٹس
The MAPBGA-81 (10x10 mm) package requires laser-via or microvia PCB fabrication for fan-out from the 0.8 mm ball pitch. Use a 4-layer stack-up with a continuous ground plane beneath the BGA. Place 100 nF decoupling capacitors at every VDD/VSS ball pair (typically 8-12 pairs), routed with minimum-loop stubs. A 0.1 uF + 10 uF bulk cap pair near the MCU package corner smooths transient loads during Ethernet PHY activation.
ColdFire V2 core current at 80 MHz (estimated: I_core ~ 50-90 mA, I/O ~ 30 mA) implies the 3.3 V rail must deliver at least 120 mA sustained plus transient headroom during Flash programming. Use a low-noise LDO (e.g., NCP1117) sourced from a 5 V bus, or a switching regulator if 5 V is the system main rail. Keep analog/digital grounds tied at a single point under the MCU and not under the PHY.
The MCF52110CVM80 needs an external 25 MHz crystal at EXTAL/XTAL; the PLL multiplies this to the 80 MHz core clock. Some early schematics used incorrect feedback-resistor values on the crystal loop - use a series resistor specified in the NXP MCF5211x reference design. Also, avoid powering the MCU while JTAG/BDM is connected to a powered programmer - many debug-interface failures trace back to bus contention during reset.
تعمیل کی معلومات
RoHS compliance confirmed by NXP product page and DigiKey listings (1678939). AEC-Q100 status not applicable - this part is industrial-grade. Halogen-free and conflict-minerals data require the NXP material declaration for the specific lot.
