OPA244PA - 430kHz Low-Power Op Amp | Texas Instruments
MPN: OPA244PA ✓ فعالOPA244PA جائزہ
An operational amplifier is an analog semiconductor that amplifies the voltage difference between its two inputs. In the broader component hierarchy, the OPA244PA is a low-power voltage-feedback operational amplifier within the amplifier IC and signal-conditioning IC families. Its internal feedback arrangement allows engineers to configure stable gain with external resistors when the required noise, bandwidth, and bias-current characteristics suit the application.
The OPA244PA's 430 kHz bandwidth supports moderate-frequency signal processing without requiring the power consumption of a high-speed amplifier. Its 50 uA per-channel quiescent current is particularly useful in portable systems where battery capacity and standby energy are important. Single-supply operation from the factory through 36 V simplifies designs that derive operating power from batteries, industrial rails, or automotive-style supply ranges. The listed output current per channel is 12 mA.
OPA244PA is a single-amplifier version of the OPA244 family. Other family members use different package formats and channel counts, so their mechanical mounting and pin arrangements must be checked before substituting them into an existing board. The OPA244PA is identified as a standard general-purpose amplifier in an 8-pin PDIP package, making it useful when a through-hole footprint and single op amp are required. Electrical performance still depends on the selected operating voltage, feedback network, load, and source impedance.
Typical uses include low-frequency sensor amplification, portable measurement systems, battery threshold detection, current sensing, and general-purpose analog buffering. The 430 kHz bandwidth is suitable for many audio-band and instrumentation signals, although applications requiring substantially more bandwidth, lower offset voltage, or rail-to-rail input and output operation should compare the OPA244PA with specialized amplifier families before finalizing the design.
A key design consideration is the power-supply range: the confirmed single-supply limit reaches 36 V. Input common-mode range, output swing, input bias current, offset voltage, and slew rate still need to be checked against the manufacturer datasheet for the actual circuit. Decoupling capacitors should be placed close to the power pins, and the feedback components should be selected with the amplifier's input and output characteristics in mind.
This product page combines the confirmed OPA244PA characteristics with package guidance, application analysis, practical design notes, and a qualified replacement assessment. It also distinguishes the 8-pin PDIP OPA244PA from SOT-23-5 versions whose smaller footprint requires a different PCB land pattern.
کے لیے ڈراپ اِن متبادل OPA244PA — یکساں پیکیج، پن سے پن مطابقت پذیر۔ مختلف پیکیج والے پرزے جن کے لیے PCB دوبارہ کام درکار ہو، شامل نہیں ہیں۔
OP07DNZ
✅ ڈراپ-اِن📋 حوالہ جاتی متبادل (کیٹلاگ میں نہیں)
OPA244PA زیادہ سے زیادہ ریٹنگز اور برقی خصوصیات
| Product Type | Single operational amplifier |
| Amplifier Type | General-purpose micropower operational amplifier |
| Number of Channels | 1 channel |
| Gain-Bandwidth Product | 430 kHz |
| کوئیسینٹ کرنٹ | 50 uA per channel |
| Single-Supply Operating Voltage | Up to 36 V |
| Output Current per Channel | 12 mA |
| پیکیج | 8-pin PDIP |
| ماؤنٹنگ اسٹائل | Through-hole |
| RoHS اسٹیٹس | RoHS details listed |
OPA244PA 8-pin pdip پن کنفیگریشن گائیڈ
OPA244PA (8-pin pdip پیکیج) کے لیے پن کنفیگریشن۔ اس اینالاگ کمپوننٹ میں اِن پٹ، آؤٹ پٹ اور پاور سپلائی پنز شامل ہیں۔ آفسیٹ نل، کمپنسیشن اور اِن ایبل پن کنفیگریشنز کے لیے مینوفیکچرر کے ڈیٹا شیٹ سے رجوع کریں۔ سگنل کنڈیشننگ اور ایمپلیفائر سرکٹس کے لیے مثالی۔
کے لیے تفصیلی پن آؤٹ ڈیٹا دستیاب نہیں OPA244PA.
رجوع کریں ڈیٹا شیٹ مکمل پن کنفیگریشن کے لیے۔
عام استعمالات
OPA244PA کے لیے موزوں ہے 6 ایپلیکیشنs: Battery-Powered Sensor Interfaces, Portable Measurement Instruments, Battery Voltage Threshold Detection, Current-Sensing Signal Conditioning, Low-Power Audio-Band Buffering, Industrial Low-Level Signal Conditioning.
Battery-Powered Sensor Interfaces
OPA244PA fits low-power sensor interfaces because its 50 uA typical quiescent current reduces standing demand while its 430 kHz gain-bandwidth product handles many slowly changing or low-bandwidth signals. The amplifier can condition a sensor output before conversion or transmission without introducing the higher power requirement of a general-purpose high-speed op amp. Place the amplifier close to the sensor and bypass the supply pins to minimize noise pickup. Confirm that the sensor signal remains within the input common-mode range, and select external feedback resistors to establish the required gain. Because OPA244PA is a single amplifier, dual-rail or dual-channel signal paths may require another device unless the signal path is multiplexed.
تجویز کردہ
Portable Measurement Instruments
OPA244PA is appropriate for compact handheld instruments that amplify low-level sensor signals while operating from a single battery or low-voltage rail. Its 430 kHz bandwidth covers many measurement signals requiring amplification and buffering, while 50 uA typical quiescent current per channel helps limit battery drain. The 8-pin PDIP format also supports through-hole construction and hand-wired prototypes. Verify input offset voltage and bias current against the required measurement accuracy, then evaluate OP07DNZ when substantially lower offset voltage is more important than operating current.
تجویز کردہ
Battery Voltage Threshold Detection
OPA244PA can amplify the difference between a battery-derived voltage and a reference for threshold or state-of-charge detection. Its single-supply operation up to 36 V permits use across multiple battery chemistries, and the 430 kHz bandwidth is more than sufficient for slow battery-voltage changes. The amplifier should be evaluated against the minimum input common-mode voltage, because the input and output must remain inside their usable ranges near the end of discharge. A low-current design also benefits from the 50 uA typical quiescent current, although leakage through high-impedance divider nodes should be controlled separately.
تجویز کردہ
Current-Sensing Signal Conditioning
OPA244PA can condition the voltage produced by a current-sense element when the signal bandwidth and common-mode limits are compatible. Its 430 kHz gain-bandwidth product supports many low- to moderate-bandwidth current measurements, and its 12 mA listed output current per channel is suitable for many low-load analog stages. Keep the sense-path traces short and use Kelvin-style routing where the shunt and amplifier are separated. Check the datasheet for input bias current and common-mode behavior because these characteristics determine the error introduced by high source impedance. OP07DNZ may offer lower input offset voltage for precise DC measurements.
تجویز کردہ
Low-Power Audio-Band Buffering
OPA244PA can buffer and gain-control signals within the audio band because its 430 kHz gain-bandwidth product is substantially higher than typical 20 Hz to 20 kHz signal frequencies. The 50 uA typical quiescent current is useful in portable audio accessories, and single-supply operation simplifies common 3.3 V or 5 V architectures. The design must account for the amplifier's output swing and load capability at the selected supply. High-gain layouts should include the compensation network recommended by the manufacturer for the selected noise gain, and the PCB should minimize feedback-loop area.
تجویز کردہ
Industrial Low-Level Signal Conditioning
OPA244PA can serve as a general-purpose signal-conditioning amplifier in industrial equipment when its supply, input range, and precision meet the circuit requirements. Single-supply operation up to 36 V supports higher-voltage systems, and the 430 kHz bandwidth accommodates many control and monitoring signals. The 8-pin PDIP package is useful for through-hole prototypes and serviceable industrial assemblies. Use local supply bypassing, route the high-impedance input away from switching nodes, and calculate the closed-loop bandwidth from the intended noise gain. If the application requires closer DC precision, compare the 700 uV OPA244PA offset with the approximately 75 uV offset of OP07DNZ.
تجویز کردہ
تجویز کردہ پروڈکٹس کا خلاصہ
کے لیے انجینئرنگ ریفرنس ڈیٹا OPA244PA — موازنہ، ڈیزائن رہنمائی، اور تعمیل کی معلومات۔
انتخاب کی گائیڈ
متبادلات کے ساتھ موازنہ
| پیرامیٹر | یہ پروڈکٹ | OP07DNZ |
|---|---|---|
| Package | 8-pin PDIP | 8-pin PDIP |
| Brand | Texas Instruments | Analog Devices |
| Input Offset Voltage | Approximately 700 uV | Approximately 75 uV |
اہم امتیازی خصوصیات
- Lower quiescent current supports portable power budgets (بمقابلہOP07DNZ)
- Moderate signal bandwidth with low-power operation (بمقابلہOP07DNZ)
- Through-hole package supports serviceable and prototype construction (بمقابلہOPA244UA)
ڈیزائن نوٹس
Place the supply bypass capacitor directly beside the OPA244PA supply and ground pins, using short traces and a low-impedance ground return. Keep the external feedback resistors close to the amplifier input and inverting-input pins to reduce parasitic capacitance and feedback-loop area. When working at the upper end of the 430 kHz bandwidth, use a grounded, short ground plane connection and avoid routing the sensitive input beneath switching or digital traces.
Confirm the complete signal path before selecting the supply. OPA244PA supports single-supply operation up to 36 V, but that maximum does not imply that inputs or outputs can swing across the entire supply range. Check the manufacturer input common-mode and output-swing limits at the intended voltage, and ensure the load current remains compatible with the listed 12 mA output current per channel. Decouple the supply locally to prevent battery wiring resistance from producing supply ripple that appears as amplified signal noise.
Do not substitute OPA244UA or OPA244NA/3K for OPA244PA on an existing board because those versions use a 5-pin SOT-23-5 package rather than an 8-pin PDIP footprint. Likewise, verify every pin function before considering OP07DNZ. Although OP07DNZ has an approximately 75 uV input offset voltage compared with approximately 700 uV for OPA244PA, lower offset does not establish complete pin compatibility, supply compatibility, bandwidth equivalence, or stability.
تعمیل کی معلومات
The OPA244PA cross-reference listing includes RoHS details, but the available material does not explicitly state the compliance result or provide the remaining environmental declarations.