OPA445AU - ±45V FET-Input Op Amp | Texas Instruments
MPN: OPA445AU ✓ فعالOPA445AU جائزہ
An operational amplifier is an analog signal-conditioning device that amplifies the voltage difference between its inverting and non-inverting inputs while providing high input impedance and low output impedance. The OPA445 belongs to the operational-amplifier hierarchy of analog ICs, where it sits above the general-purpose amplifier category and below precision, high-voltage, and instrumentation amplifiers. Its high-voltage capability makes it suitable for industrial and instrumentation circuits that operate beyond conventional low-voltage op-amp rails.
The OPA445AU features a wide power-supply range of up to ±45 V, a 15 V/µs slew rate, and input bias current of 10 pA. The 2 MHz gain-bandwidth product supports moderate-gain signal paths, while the 15 mA output-current capability provides useful drive for downstream stages. FET input architecture minimizes input bias current, which is advantageous when the source impedance is high and source leakage would otherwise distort the measured signal.
The monolithic amplifier architecture is intended for applications requiring high output-voltage or large common-mode-voltage swings. Its operating characteristics make it relevant to industrial sensor conditioning, high-voltage measurement front ends, test equipment, audio paths, and power-system instrumentation. Because the device supports bipolar supplies of up to ±45 V, its input and output stages must be designed to remain within the datasheet limits even when the system uses a narrower rail voltage.
Typical uses include buffering high-impedance transducers, amplifying bipolar sensor signals, driving analog measurement chains, and providing gain in laboratory equipment. The 10 pA input bias current reduces loading on sensitive sources, while the 15 V/µs slew rate allows the amplifier to follow relatively fast signal transitions. At low closed-loop gain, bandwidth limits and stability considerations become more important than slew-rate limits.
For PCB implementation, use the manufacturer pin-description table when assigning traces and power connections, keep input and feedback paths short, and decouple each supply rail close to the device. Account for the SOIC-8 thermal limitations under sustained high output voltage and current. A practical design review should verify common-mode range, output swing, supply polarity, and stability with the intended gain and load.
This page combines the OPA445AU specifications, verified drop-in candidates, comparison parameters, and practical design guidance to support component selection, PCB planning, and replacement decisions beyond the basic manufacturer ordering information.
کے لیے ڈراپ اِن متبادل OPA445AU — یکساں پیکیج، پن سے پن مطابقت پذیر۔ مختلف پیکیج والے پرزے جن کے لیے PCB دوبارہ کام درکار ہو، شامل نہیں ہیں۔
OPA445BM
✅ ڈراپ-اِن📋 حوالہ جاتی متبادل (کیٹلاگ میں نہیں)
OPA445AID
✅ ڈراپ-اِن ⚠️ تفصیلات غیر تصدیق شدہ📋 حوالہ جاتی متبادل (کیٹلاگ میں نہیں)
OPA445AU زیادہ سے زیادہ ریٹنگز اور برقی خصوصیات
| Amplifier Type | Single operational amplifier |
| Input Bias Current | 10 pA |
| Maximum Supply Voltage | ±45 V |
| زیادہ سے زیادہ آؤٹ پٹ کرنٹ | 15 mA |
| Gain-Bandwidth Product | 2 MHz |
| Slew Rate | 15 V/µs |
| Input Type | FET input |
| Number of Circuits | 1 circuit |
| Application Category | General-purpose amplifier |
| پیکیج | 8-pin SOIC |
| Package Width | 3.90 mm |
OPA445AU 3.90 mm پن کنفیگریشن گائیڈ
OPA445AU (3.90 mm پیکیج) کے لیے پن کنفیگریشن۔ اس اینالاگ کمپوننٹ میں اِن پٹ، آؤٹ پٹ اور پاور سپلائی پنز شامل ہیں۔ آفسیٹ نل، کمپنسیشن اور اِن ایبل پن کنفیگریشنز کے لیے مینوفیکچرر کے ڈیٹا شیٹ سے رجوع کریں۔ سگنل کنڈیشننگ اور ایمپلیفائر سرکٹس کے لیے مثالی۔
کے لیے تفصیلی پن آؤٹ ڈیٹا دستیاب نہیں OPA445AU.
رجوع کریں ڈیٹا شیٹ مکمل پن کنفیگریشن کے لیے۔
عام استعمالات
OPA445AU کے لیے موزوں ہے 6 ایپلیکیشنs: Industrial Sensor Signal Conditioning, High-Voltage Measurement Buffer, Laboratory Test Equipment, Power-System Instrumentation, Audio and Signal Amplification, Precision Feedback and Filtering.
Industrial Sensor Signal Conditioning
The OPA445AU suits high-impedance industrial sensor front ends that operate on elevated supply rails. Its 10 pA input bias current minimizes the DC error introduced by resistive sensors with high source impedance, while operation up to ±45 V supports interface circuits located near high-voltage process equipment. The amplifier can provide differential gain around a low-noise reference and drive the input stage of an ADC or data-acquisition system. Designers should verify the required common-mode range and output swing for the selected supply voltage, add input filtering for sensor wiring, and use guarding to reduce PCB leakage. The 15 V/µs slew rate is useful when sensor transients are faster than the 2 MHz small-signal bandwidth alone suggests, although loop stability must be checked at the selected gain.
تجویز کردہ
High-Voltage Measurement Buffer
OPA445AU can buffer high-voltage measurement signals without relying on a conventional low-voltage op amp. Its specified operation up to ±45 V and 10 pA input bias current are valuable when measuring divided high-voltage nodes, buffered probes, or low-current sensing elements. Placing the device as a voltage follower can reduce loading while preserving the measured level, or it can form a gain stage around a precision feedback network. The design must still confirm that the input common-mode voltage, output swing, and absolute maximum ratings include transients and component tolerances. Use protected board layouts, suitable input attenuation, and a low-leakage feedback network. The 15 mA output-current specification allows moderate loading, but downstream capacitance should be checked for stability.
تجویز کردہ
Laboratory Test Equipment
The OPA445AU is appropriate for laboratory and electronic test equipment that requires flexible gain, high input impedance, and operation from elevated bipolar rails. Its 2 MHz gain-bandwidth product is useful in moderate-bandwidth instrumentation paths, and the 10 pA input bias current reduces loading on probes and high-value test sources. The amplifier can implement non-inverting, inverting, differential, and active-filter stages when stable compensation and feedback values are selected from the manufacturer guidance. At higher closed-loop gains, bandwidth and noise rather than slew rate usually dominate the response. Keep sensitive input traces short, decouple the supply pins locally, and verify the output load because the device's 15 mA rating is not a guarantee of unrestricted capacitive drive.
تجویز کردہ
Power-System Instrumentation
OPA445AU can amplify scaled voltage signals associated with power-system monitoring when the measurement interface operates above ordinary low-voltage analog rails. The ±45 V capability supports bipolar signal conditioning around zero, while the low 10 pA input bias current is beneficial when the front end includes high-value dividers or isolation-related components. The amplifier may drive an ADC input, comparator, or monitoring controller after appropriate scaling and filtering. Protection components must be selected for the actual fault voltage, and the amplifier's input and output limits should be checked under transients rather than only nominal conditions. The 15 V/µs slew rate helps reproduce faster transitions, but the 2 MHz bandwidth limits accurate response to high-frequency events. Maintain a defined analog ground and isolate the measurement path from switching-power nodes.
تجویز کردہ
Audio and Signal Amplification
OPA445AU can provide gain and buffering in audio or general signal-amplification paths when a high-voltage rail and wide output swing are more important than low-noise precision. Its 15 V/µs slew rate is well suited to preserving large-signal edges, while the 2 MHz gain-bandwidth product limits small-signal bandwidth and places an upper limit on usable gain at high frequencies. FET inputs reduce bias-current-related distortion in high-impedance sources, although noise and distortion specifications must be checked against the audio requirements. The output-current limit of 15 mA supports modest loads but not low-ohm headphone or speaker stages without a driver. Keep feedback components compact, provide local supply bypass, and test the configured filter or gain stage across the required signal bandwidth.
تجویز کردہ
Precision Feedback and Filtering
OPA445AU can implement active filters, integrators, and precision feedback networks on high-voltage rails. Its low 10 pA input bias current reduces DC error in high-value feedback resistors, while operation up to ±45 V enables signal processing around elevated bipolar supply nodes. The 2 MHz gain-bandwidth product must be checked against the intended closed-loop bandwidth and phase margin; narrow-band filters require component tolerances and parasitics to be included in the response calculation. A 15 V/µs slew rate can improve large-signal behavior, but it does not remove the small-signal bandwidth or stability limits. Use the manufacturer feedback and compensation guidance, keep sensitive summing nodes compact, and ensure resistor ratings and dielectric types suit the operating voltage.
تجویز کردہ
تجویز کردہ پروڈکٹس کا خلاصہ
کے لیے انجینئرنگ ریفرنس ڈیٹا OPA445AU — موازنہ، ڈیزائن رہنمائی، اور تعمیل کی معلومات۔
انتخاب کی گائیڈ
متبادلات کے ساتھ موازنہ
| پیرامیٹر | یہ پروڈکٹ | OPA445BM | OPA445AID |
|---|---|---|---|
| Brand | Texas Instruments | Texas Instruments | Texas Instruments |
| Package | 8-pin SOIC | 8-pin SOIC | 8-pin SOIC |
| Amplifier Type | Single high-voltage FET-input operational amplifier | Single high-voltage FET-input operational amplifier | Single high-voltage FET-input operational amplifier |
| Maximum Supply Voltage | ±45 V | ±45 V | ±45 V |
| Gain-Bandwidth Product | 2 MHz | 2 MHz | 2 MHz |
| Slew Rate | 15 V/µs | 15 V/µs | 15 V/µs |
| Input Bias Current | 10 pA | 10 pA | 10 pA |
| Maximum Output Current | 15 mA | 15 mA | 15 mA |
| Input Architecture | FET input | FET input | FET input |
اہم امتیازی خصوصیات
- Combines a high-voltage rail with very low input bias current (بمقابلہOPA445AID)
- Documented primary-parameter equivalence (بمقابلہOPA445BM)
- No low-voltage input penalty for elevated industrial rails (بمقابلہConventional low-voltage operational amplifiers)
ڈیزائن نوٹس
Place bypass capacitors beside the OPA445AU supply and ground pins, and keep the return path short enough to avoid adding inductance between the capacitor and the device. Route the input and feedback components close to their associated pins, especially in high-gain or precision-filter configurations. A solid analog ground plane helps establish predictable return currents, but high-current switching paths should remain separated from sensitive input nodes.
Do not treat the ±45 V maximum supply rating as permission to exceed the input common-mode range or output swing. Check the complete electrical characteristics for the selected supply voltage, and include transients, tolerances, and protection-diode drops in the worst-case analysis. Likewise, the 15 mA output-current rating does not guarantee stable operation into every capacitive load. Confirm the feedback network and load condition against the manufacturer guidance.
The 2 MHz gain-bandwidth product requires careful attention to closed-loop gain and phase margin. A 15 V/µs slew rate supports large-signal transitions but does not extend small-signal bandwidth. Use stable resistor and capacitor values, minimize parasitic capacitance around high-impedance summing nodes, and test the completed layout with realistic source and load impedances. Guarding may be necessary where board leakage could compete with the specified 10 pA input bias current.
Estimated: with a 12 V total supply span, a 4.5 V output, and 15 mA output current, the ideal output-stage dissipation is approximately (12 V - 4.5 V) × 0.015 A = 112.5 mW. Actual device heating also includes quiescent and internal losses. This estimate uses a 12 V total span, 4.5 V output, and 15 mA load; use the manufacturer power-dissipation limits and the actual operating conditions for the final SOIC-8 thermal assessment.
تعمیل کی معلومات
RoHS, REACH, AEC-Q100, lead-free, halogen-free, and conflict-minerals status require confirmation from the manufacturer product documentation.