OPA604AP - FET Audio Op Amp | Texas Instruments
MPN: OPA604AP ✓ فعالOPA604AP جائزہ
An operational amplifier is a voltage-gain, active-feedback component that compares an input signal with a feedback network and drives its output to reduce the difference between them. Operational amplifiers belong to the broader amplifier IC and analog signal-conditioning hierarchy. FET-input amplifiers use field-effect transistors at the input, supporting low input bias current and effective operation with high-impedance sources.
The OPA604AP is intended for applications where low distortion, low noise, wide bandwidth, and high dynamic range are more important than minimum power consumption. Key benefits include low-distortion operation at 1 kHz, 10 nV/sqrt(Hz) noise density, 20 MHz gain-bandwidth product, and unity-gain stability. These characteristics support precise signal amplification, active filtering, and current-to-voltage conversion without adding substantial distortion.
Its wide supply range accommodates conventional bipolar audio rails, higher-voltage analog systems, and lower-voltage designs. The low-noise FET input maintains wide dynamic range even when driven from a high source impedance. Laser-trimmed offset voltage is also used to reduce the need for interstage coupling capacitors, making the amplifier easier to deploy in straightforward audio signal paths.
Typical uses include professional audio equipment, PCM digital-to-analog converter current-to-voltage conversion, spectral-analysis instrumentation, active crossover networks, line-level preamplifiers, and precision test equipment. The combination of low noise and low distortion is particularly useful where small signal details must remain intelligible at the output.
Designers should preserve adequate output headroom, verify the common-mode range across the complete signal excursion, and place input and feedback components close to the device to minimize parasitic feedback. The through-hole package also requires adequate spacing for a stable breadboard or through-hole layout rather than a compact surface-mount assembly.
This product page combines manufacturer specifications, application guidance, pin information, and replacement considerations into an engineering-focused reference. It is designed to support circuit planning, source selection, and PCB design for low-noise audio and precision analog systems.
کے لیے ڈراپ اِن متبادل OPA604AP — یکساں پیکیج، پن سے پن مطابقت پذیر۔ مختلف پیکیج والے پرزے جن کے لیے PCB دوبارہ کام درکار ہو، شامل نہیں ہیں۔
اس سیریز میں مختلف ورژن
اسی سیریز کے ماڈلز جو ڈراپ اِن مطابقت رکھتے ہیں OPA604AP (یکساں فارم فیکٹر اور فٹ پرنٹ) — میں مختلف Amplifier Type, Number of Circuits, Slew Rate, Supply Voltage Range, Unity-Gain Bandwidth.
OPA2604AP
✅ ڈراپ-اِن📋 حوالہ جاتی متبادل (کیٹلاگ میں نہیں)
OPA134PA
✅ ڈراپ-اِنقیمت کے لیے رابطہ کریں
ڈیٹا شیٹ دیکھیں →OPA604AP زیادہ سے زیادہ ریٹنگز اور برقی خصوصیات
| Amplifier Type | Single-circuit operational amplifier |
| Input Transistor Type | FET |
| Unity-Gain Bandwidth | 20 MHz |
| Slew Rate | 25 V/us |
| Input Noise Density | 10 nV/sqrt(Hz) |
| Maximum Total Supply Voltage | 48 V |
| Supply Voltage Range | 5 V to 48 V total |
| Maximum Symmetric Supply | ±24 V |
| Gain Stability | Unity-gain stable |
| آپریٹنگ درجہ حرارت رینج | -25 C to +85 C |
| پیکیج | 8-pin plastic mini-DIP |
| ماؤنٹنگ ٹائپ | Through-hole |
| Offset Voltage | Laser-trimmed |
| Distortion | Low at 1 kHz |
| Number of Circuits | 1 circuit |
| RoHS اسٹیٹس | unknown |
| REACH Status | unknown |
OPA604AP پن کنفیگریشن
| پن 1 | NULL — Offset null terminal |
| پن 2 | IN- — Inverting input |
| پن 3 | IN+ — Non-inverting input |
| پن 4 | V- — Negative supply connection |
| پن 5 | NULL — Offset null terminal |
| پن 6 | OUT — Output |
| پن 7 | V+ — Positive supply connection |
| پن 8 | NC — Not connected |
عام استعمالات
OPA604AP کے لیے موزوں ہے 6 ایپلیکیشنs: PCM DAC Current-to-Voltage Conversion, Professional Audio Preamplifier, Spectral Analysis Instrumentation, Active Crossover and Filter Network, Line-Level Buffer and Signal Conditioning, Precision Test and Measurement Front End.
PCM DAC Current-to-Voltage Conversion
The OPA604AP is well suited to converting the differential current output of a PCM DAC into a ground-referenced voltage. Its FET input supports high-impedance summing junctions, while the 20 MHz unity-gain bandwidth and 25 V/us slew rate provide margin for full-scale audio signals. According to the manufacturer, the amplifier is unity-gain stable and intended for PCM DAC I/V conversion. The feedback network should be selected around the converter’s compliance range, output capacitance, and target full-scale voltage. Confirm DAC settling behavior across the operating bandwidth and check the amplifier’s output swing before accepting the audio path.
تجویز کردہ
Professional Audio Preamplifier
OPA604AP provides the low-noise, high-dynamic-range input stage needed in professional audio preamplifiers. Its 10 nV/sqrt(Hz) input noise supports quiet amplification of microphone- or line-level signals, and the 25 V/us slew rate reduces slew-related distortion in fast transients. The wide ±24 V capability accommodates traditional studio power rails. Choose resistor values that preserve signal headroom and keep the gain-bandwidth product high enough for the intended audio bandwidth. The FET input also suits high-impedance sources, but the source impedance should be checked against the complete noise and bias-current specification.
تجویز کردہ
Spectral Analysis Instrumentation
The OPA604AP can condition low-level signals in spectral-analysis equipment where noise and distortion limit measurement fidelity. Its low 10 nV/sqrt(Hz) input noise preserves small-signal information, while the 20 MHz unity-gain bandwidth covers a substantially wider range than conventional audio amplifiers. Unity-gain stability permits direct use as a buffer when impedance conversion is required. Layout must minimize leakage and ground-loop contributions around the sensitive input node, and the gain structure should avoid amplifying noise outside the instrument’s measurement bandwidth.
تجویز کردہ
Active Crossover and Filter Network
OPA604AP is suitable for active crossover and audio filter networks that require low distortion across several audio decades. The 20 MHz unity-gain bandwidth and 25 V/us slew rate provide ample loop-gain margin compared with typical 20 kHz audio crossover bands, while the FET input avoids excessive loading on preceding filter stages. Select Q, gain, and component tolerances to control phase and cutoff accuracy. Check every filter stage for stable operation at the closed-loop gain selected, because compensation limits and output drive can alter the usable topology.
تجویز کردہ
Line-Level Buffer and Signal Conditioning
OPA604AP can serve as a high-impedance buffer between a source and a balanced audio output stage. Unity-gain stability supports direct follower operation, and the low-noise FET input preserves source detail when the preceding circuit has high output impedance. The 25 V/us slew rate helps maintain low distortion through rapidly changing music signals. Keep the buffer input path short, avoid placing high-impedance nodes near switching nodes, and confirm that the destination can be driven through the amplifier’s output-current and capacitive-load limits.
تجویز کردہ
Precision Test and Measurement Front End
OPA604AP is useful in laboratory front ends that require low-noise amplification without sacrificing bandwidth or transient response. The 10 nV/sqrt(Hz) input noise density supports measurement of small analog signals, and the 20 MHz unity-gain bandwidth allows the amplifier to operate beyond audio-band requirements. It can also buffer high-impedance detectors or sensors before an ADC. Verify input bias current, input offset voltage, common-mode range, and output current against the source and ADC interface, then use guarding or shielding techniques where leakage could affect the measurement.
تجویز کردہ
تجویز کردہ پروڈکٹس کا خلاصہ
کے لیے انجینئرنگ ریفرنس ڈیٹا OPA604AP — موازنہ، ڈیزائن رہنمائی، اور تعمیل کی معلومات۔
انتخاب کی گائیڈ
متبادلات کے ساتھ موازنہ
| پیرامیٹر | یہ پروڈکٹ | OPA2604AP | OPA134PA |
|---|---|---|---|
| Package | 8-pin plastic mini-DIP | 8-pin plastic mini-DIP | 8-pin plastic mini-DIP |
| Brand | Texas Instruments | Texas Instruments | Texas Instruments |
| Input Type | FET | FET | FET |
| Primary Application | Low-distortion audio and wide-bandwidth analog signal amplification | Low-distortion FET-input audio amplification | FET-input audio amplification |
اہم امتیازی خصوصیات
- High bandwidth and slew rate for low-distortion audio (بمقابلہOPA134PA)
- Designed specifically for enhanced AC performance (بمقابلہOPA2604AP)
- Wide high-voltage operating capability (بمقابلہOPA134PA)
ڈیزائن نوٹس
Route the OPA604AP input and feedback paths away from clock, switching-regulator, and digital-signal traces. Keep the non-inverting input node as short as practical, use a quiet ground reference, and place feedback resistors close to pins 2 and 6. On a through-hole design, avoid long exposed input leads that can act as antennas and increase noise pickup.
Use a low-noise supply and decouple each supply pin locally with a stable ceramic capacitor plus an appropriate bulk capacitor. The manufacturer permits operation up to ±24 V, but usable output swing is lower because of headroom limitations. Verify the actual output waveform across input and load conditions, and include additional filtering if the supply contains switching ripple.
Do not treat an 8-pin DIP amplifier as interchangeable solely because another part also has eight pins. Confirm offset-null locations, supply pins, input polarity, output pin, and stability in the manufacturer pin table. Also check the alternative’s input offset voltage, bias current, common-mode range, and gain-bandwidth product before modifying a validated audio circuit.
For PCM DAC current-to-voltage conversion, account for parasitic capacitance at the summing node and verify converter settling time. Place the I/V feedback network close to the amplifier and DAC output, and probe the node with a low-capacitance instrument. If the circuit is unstable or exhibits peaking, reduce loop gain or add compensation only after checking the DAC datasheet’s recommended configuration.
تعمیل کی معلومات
The accessible manufacturer product information does not state the requested compliance statuses. Use the Texas Instruments product page and current manufacturer documentation for procurement-specific declarations.
