OPA658U-1 - 900MHz Current-Feedback Op Amp | Texas Instruments
MPN: OPA658U-1 ✓ فعالOPA658U-1 جائزہ
A current-feedback operational amplifier is a voltage-feedback amplifier variant whose closed-loop bandwidth behavior is primarily set by external feedback resistors. It belongs to the broader hierarchy of operational amplifiers, analog amplifiers, analog signal-conditioning ICs, and semiconductor devices. This topology is particularly useful when a design must preserve bandwidth and output-drive capability across a wide signal-frequency range rather than only at small signal amplitudes.
The OPA658U-1 provides 900 MHz bandwidth, 1700 V/us slew rate, and 5.7 uA quiescent current. These three characteristics make it appropriate for demanding high-speed signal paths where low power is also important. Its current-feedback architecture supports strong large-signal performance, while its low quiescent current reduces supply demand in portable and compact systems. The device is identified as a single operational amplifier with a 5.7 uA bias current in its published product listing.
The wideband behavior makes the amplifier useful in high-resolution video, medical imaging, and digital-to-analog converter current-to-voltage conversion. Unlike an amplifier whose bandwidth is determined mainly by internal gain-bandwidth behavior, the OPA658 family gives the circuit designer direct control through the feedback network. Component tolerance and parasitic inductance must therefore be managed carefully when designing for very high closed-loop bandwidth or demanding pulse response.
Typical signal-processing uses include high-speed video amplification, medical-imaging front ends, DAC output current-to-voltage conversion, portable instrumentation, and low-power wideband test circuits. In a current-to-voltage converter, the amplifier works with an external feedback resistor and DAC output network, allowing the feedback component to define the conversion scale. In video and imaging systems, its combination of wide bandwidth, low power, and strong large-signal response supports compact analog channels operating at high signal rates.
PCB implementation is a central design consideration for a 900 MHz device. Keep feedback components and output routing short, use a low-inductance ground return, and place decoupling capacitors close to the supply pins. Stable feedback ratios and carefully controlled resistor values are essential because the current-feedback amplifier’s bandwidth and peaking behavior depend on the complete feedback network rather than on the amplifier alone.
This product page combines the key operating specifications with package guidance, pin assignments, design notes, and a conservative replacement analysis. The available comparison focuses on verified same-footprint parts and clearly separates exact ordering-code differences from changes that would require PCB or signal-chain redesign.
کے لیے ڈراپ اِن متبادل OPA658U-1 — یکساں پیکیج، پن سے پن مطابقت پذیر۔ مختلف پیکیج والے پرزے جن کے لیے PCB دوبارہ کام درکار ہو، شامل نہیں ہیں۔
OPA658U
✅ ڈراپ-اِن📋 حوالہ جاتی متبادل (کیٹلاگ میں نہیں)
OPA658UB
✅ ڈراپ-اِن📋 حوالہ جاتی متبادل (کیٹلاگ میں نہیں)
OPA658U-1 زیادہ سے زیادہ ریٹنگز اور برقی خصوصیات
| Amplifier Type | Single-channel current-feedback operational amplifier |
| Number of Channels | 1 channel |
| Gain-Bandwidth Product | 900 MHz |
| Slew Rate | 1700 V/us |
| کوئیسینٹ کرنٹ | 5.7 uA per amplifier |
| سپلائی وولٹیج | ±5.5 V |
| Total Supply Voltage | 11 V |
| پیکیج | 8-pin SOIC |
| پن کی تعداد | 8 pins |
| ماؤنٹنگ ٹائپ | Surface mount |
| RoHS اسٹیٹس | unknown |
| REACH Status | unknown |
| AEC-Q100 Qualification | unknown |
OPA658U-1 پن کنفیگریشن
| پن 1 | NC — Not connected |
| پن 2 | -IN — Inverting input |
| پن 3 | +IN — Non-inverting input |
| پن 4 | V- — Negative supply connection |
| پن 5 | NC — Not connected |
| پن 6 | NC — Not connected |
| پن 7 | V+ — Positive supply connection |
| پن 8 | OUT — Output |
عام استعمالات
OPA658U-1 کے لیے موزوں ہے 6 ایپلیکیشنs: High-Resolution Video Signal Conditioning, Medical Imaging Analog Front End, DAC Current-to-Voltage Conversion, Portable Wideband Instrumentation, Industrial High-Speed Sensor Interface, Low-Power Wideband Test and Measurement.
High-Resolution Video Signal Conditioning
The OPA658U-1 fits high-resolution video channels because its 900 MHz bandwidth provides substantial frequency range and its 1700 V/us slew rate supports rapid large-signal transitions. The current-feedback architecture is particularly useful when the amplifier must maintain response beyond the small-signal bandwidth region. Place the feedback resistor close to the inverting input, minimize output routing, and use a low-inductance ground reference. The benefit is a compact 8-pin SOIC implementation for wideband video conditioning, provided that PCB parasitics are controlled.
تجویز کردہ
Medical Imaging Analog Front End
The OPA658U-1 is applicable to medical-imaging analog front ends because the Texas Instruments OPA658 family is identified for medical imaging and combines wide bandwidth with low power. Its 900 MHz bandwidth supports high-rate sensor signals, while the 5.7 uA quiescent current suits power-conscious acquisition electronics. Use short feedback paths and careful return grounding to limit high-frequency coupling. System designers must separately validate patient-safety isolation, diagnostic accuracy, and regulatory requirements rather than treating amplifier qualification as complete device approval.
تجویز کردہ
DAC Current-to-Voltage Conversion
The OPA658U-1 supports DAC current-to-voltage conversion by combining 900 MHz bandwidth with a 1700 V/us slew rate. In the I/V topology, an external feedback resistor establishes the conversion scale and must be considered together with the DAC output capacitance and amplifier stability limits. Keeping that resistor and its associated parasitic capacitance close to the inverting input improves bandwidth and settling behavior. This arrangement is useful for high-resolution signal generation, instrumentation, and waveform-generation systems requiring a fast analog output stage.
تجویز کردہ
Portable Wideband Instrumentation
The OPA658U-1 suits portable wideband instrumentation because it provides 900 MHz bandwidth while drawing only 5.7 uA quiescent current. That combination allows a compact 8-pin SOIC implementation in battery-operated or space-constrained equipment. The trade-off is that high-frequency analog design becomes more sensitive to resistor tolerances, capacitor selection, and board parasitics than a low-frequency precision amplifier. Designers should verify settling at the required signal rate, use a stable power supply, and keep the feedback network compact.
تجویز کردہ
Industrial High-Speed Sensor Interface
The OPA658U-1 can serve as a high-speed interface for industrial sensors requiring bandwidth beyond the range of conventional precision op amps. Its 900 MHz bandwidth and 1700 V/us slew rate provide headroom for fast sensor waveforms and trigger events, while the 5.7 uA quiescent current reduces supply burden in distributed equipment. Place input and feedback components near the device, maintain a continuous ground return, and account for connector and cable resonances. The result is a compact analog channel suited to fast industrial monitoring systems.
تجویز کردہ
Low-Power Wideband Test and Measurement
The OPA658U-1 is useful in low-power wideband test and measurement circuits where 900 MHz bandwidth, 1700 V/us slew rate, and 5.7 uA quiescent current must coexist in a small package. It can form the output driver or input-conditioning stage of a compact measurement system. Use the manufacturer’s feedback recommendations as the starting point, and verify stability across resistor and capacitor tolerances. The principal benefit is high-frequency capability without the higher supply demand associated with many wideband amplifiers.
تجویز کردہ
تجویز کردہ پروڈکٹس کا خلاصہ
کے لیے انجینئرنگ ریفرنس ڈیٹا OPA658U-1 — موازنہ، ڈیزائن رہنمائی، اور تعمیل کی معلومات۔
انتخاب کی گائیڈ
متبادلات کے ساتھ موازنہ
| پیرامیٹر | یہ پروڈکٹ | OPA658U | OPA658UB |
|---|---|---|---|
| Package | 8-pin SOIC | 8-pin SOIC | 8-pin SOIC |
| Brand | Texas Instruments | Texas Instruments | Texas Instruments |
| Amplifier Architecture | Current feedback | Current feedback | Current feedback |
| Bandwidth | 900 MHz | 900 MHz | 900 MHz |
| Slew Rate | 1700 V/us | 1700 V/us | 1700 V/us |
| Quiescent Current | 5.7 uA | 5.7 uA | 5.7 uA |
| Supply Voltage | ±5.5 V | ±5.5 V | ±5.5 V |
| Number of Channels | 1 channel | 1 channel | 1 channel |
| Number of Pins | 8 pins | 8 pins | 8 pins |
| Primary Applications | High-resolution video, medical imaging, DAC I/V conversion, portable equipment | High-resolution video, medical imaging, DAC I/V conversion, portable equipment | High-resolution video, medical imaging, DAC I/V conversion, portable equipment |
اہم امتیازی خصوصیات
- Wideband current-feedback performance (بمقابلہOPA658U)
- Low quiescent current for a wideband amplifier (بمقابلہOPA658UB)
- Package-compatible service replacement (بمقابلہOPA658P)
ڈیزائن نوٹس
Place feedback resistors and their associated compensation capacitors directly beside the OPA658U-1 input pins. Keep the output route short, avoid broad loops between the amplifier and feedback network, and provide a continuous ground reference under the device. At 900 MHz, trace inductance, pad capacitance, and resistor parasitics can affect stability and peaking even when the nominal feedback values are correct.
Treat the complete feedback network as part of the amplifier design. Resistor tolerance, series inductance, and the impedance presented by the source or load can change the effective closed-loop bandwidth. Use the manufacturer’s recommended feedback values as the starting point, evaluate stability across tolerance extremes, and keep sensitive input nodes physically separate from high-current output and supply-return paths.
Decouple each supply connection close to the corresponding device pin and maintain low impedance from the capacitor to the package ground or supply return. The OPA658U-1 has a 5.7 uA quiescent current, but dynamic output current and external circuit loads can dominate total supply demand. Verify the power source can support the required signal amplitude without injecting supply noise into the output.
Do not substitute the OPA658P for the OPA658U-1 on an existing board. The OPA658P is a PDIP-8 device, while the OPA658U-1 uses an 8-pin SOIC footprint; changing between them requires a different PCB land pattern. Also check the complete ordering code for temperature-grade and qualification requirements instead of assuming every OPA658 suffix is interchangeable.
تعمیل کی معلومات
No definitive RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals declarations were present in the available product information.