Texas Instruments

OPA658U-1 - 900MHz Current-Feedback Op Amp | Texas Instruments

N.º de pieza: OPA658U-1 ✓ Activo
±5.5 V Vdss 5.7 uA per amplifier Id 8-pin SOIC Package
MOQ: 1 |

OPA658U-1 Descripción general

The Texas Instruments OPA658U-1 is a single-channel, wideband, low-power current-feedback operational amplifier with 900 MHz bandwidth, 1700 V/us slew rate, and 5.7 uA quiescent current, housed in an 8-pin SOIC package. It is designed for ±5.5 V supplies and combines the large-signal response of current-feedback topology with low power consumption.

A current-feedback operational amplifier is a voltage-feedback amplifier variant whose closed-loop bandwidth behavior is primarily set by external feedback resistors. It belongs to the broader hierarchy of operational amplifiers, analog amplifiers, analog signal-conditioning ICs, and semiconductor devices. This topology is particularly useful when a design must preserve bandwidth and output-drive capability across a wide signal-frequency range rather than only at small signal amplitudes.

The OPA658U-1 provides 900 MHz bandwidth, 1700 V/us slew rate, and 5.7 uA quiescent current. These three characteristics make it appropriate for demanding high-speed signal paths where low power is also important. Its current-feedback architecture supports strong large-signal performance, while its low quiescent current reduces supply demand in portable and compact systems. The device is identified as a single operational amplifier with a 5.7 uA bias current in its published product listing.

The wideband behavior makes the amplifier useful in high-resolution video, medical imaging, and digital-to-analog converter current-to-voltage conversion. Unlike an amplifier whose bandwidth is determined mainly by internal gain-bandwidth behavior, the OPA658 family gives the circuit designer direct control through the feedback network. Component tolerance and parasitic inductance must therefore be managed carefully when designing for very high closed-loop bandwidth or demanding pulse response.

Typical signal-processing uses include high-speed video amplification, medical-imaging front ends, DAC output current-to-voltage conversion, portable instrumentation, and low-power wideband test circuits. In a current-to-voltage converter, the amplifier works with an external feedback resistor and DAC output network, allowing the feedback component to define the conversion scale. In video and imaging systems, its combination of wide bandwidth, low power, and strong large-signal response supports compact analog channels operating at high signal rates.

PCB implementation is a central design consideration for a 900 MHz device. Keep feedback components and output routing short, use a low-inductance ground return, and place decoupling capacitors close to the supply pins. Stable feedback ratios and carefully controlled resistor values are essential because the current-feedback amplifier’s bandwidth and peaking behavior depend on the complete feedback network rather than on the amplifier alone.

This product page combines the key operating specifications with package guidance, pin assignments, design notes, and a conservative replacement analysis. The available comparison focuses on verified same-footprint parts and clearly separates exact ordering-code differences from changes that would require PCB or signal-chain redesign.

Alternativas directas para OPA658U-1 — mismo encapsulado, compatible pin a pin. Se excluyen las piezas de otro encapsulado que requieren retrabajo de la PCB.

OPA658U

✅ Sustitución directa
📦 8-pin SOIC
Same 8-pin SOIC footprint and key ratings of 900 MHz bandwidth, 1700 V/us slew rate, and 5.7 uA quiescent current; only the ordering-code suffix differs.

📋 Alternativa de referencia (no en el catálogo)

OPA658UB

✅ Sustitución directa
📦 8-pin SOIC
Same 8-pin SOIC package and OPA658 family architecture; the published core ratings differ by 0% in bandwidth and slew rate, while the exact grade distinction is not stated.

📋 Alternativa de referencia (no en el catálogo)

OPA658U-1 Valores máximos y características eléctricas

Amplifier Type Single-channel current-feedback operational amplifier
Number of Channels 1 channel
Gain-Bandwidth Product 900 MHz
Slew Rate 1700 V/us
Corriente en reposo 5.7 uA per amplifier
Tensión de alimentación ±5.5 V
Total Supply Voltage 11 V
Encapsulado 8-pin SOIC
Recuento de pines 8 pins
Tipo de montaje Surface mount
Estado RoHS unknown
REACH Status unknown
AEC-Q100 Qualification unknown

Configuración de pines de OPA658U-1

SOIC-8 Package Pinout Diagram SOIC-8 8-pin small outline IC, 3.9x4.9mm, P1.27mm, JEDEC MS-012. 1 8 2 7 3 6 4 5 SOIC-8
Pin 1 NC — Not connected
Pin 2 -IN — Inverting input
Pin 3 +IN — Non-inverting input
Pin 4 V- — Negative supply connection
Pin 5 NC — Not connected
Pin 6 NC — Not connected
Pin 7 V+ — Positive supply connection
Pin 8 OUT — Output

Aplicaciones típicas

OPA658U-1 es adecuado para 6 aplicacións: High-Resolution Video Signal Conditioning, Medical Imaging Analog Front End, DAC Current-to-Voltage Conversion, Portable Wideband Instrumentation, Industrial High-Speed Sensor Interface, Low-Power Wideband Test and Measurement.

📺

High-Resolution Video Signal Conditioning

The OPA658U-1 fits high-resolution video channels because its 900 MHz bandwidth provides substantial frequency range and its 1700 V/us slew rate supports rapid large-signal transitions. The current-feedback architecture is particularly useful when the amplifier must maintain response beyond the small-signal bandwidth region. Place the feedback resistor close to the inverting input, minimize output routing, and use a low-inductance ground reference. The benefit is a compact 8-pin SOIC implementation for wideband video conditioning, provided that PCB parasitics are controlled.

💊

Medical Imaging Analog Front End

The OPA658U-1 is applicable to medical-imaging analog front ends because the Texas Instruments OPA658 family is identified for medical imaging and combines wide bandwidth with low power. Its 900 MHz bandwidth supports high-rate sensor signals, while the 5.7 uA quiescent current suits power-conscious acquisition electronics. Use short feedback paths and careful return grounding to limit high-frequency coupling. System designers must separately validate patient-safety isolation, diagnostic accuracy, and regulatory requirements rather than treating amplifier qualification as complete device approval.

⚡

DAC Current-to-Voltage Conversion

The OPA658U-1 supports DAC current-to-voltage conversion by combining 900 MHz bandwidth with a 1700 V/us slew rate. In the I/V topology, an external feedback resistor establishes the conversion scale and must be considered together with the DAC output capacitance and amplifier stability limits. Keeping that resistor and its associated parasitic capacitance close to the inverting input improves bandwidth and settling behavior. This arrangement is useful for high-resolution signal generation, instrumentation, and waveform-generation systems requiring a fast analog output stage.

📱

Portable Wideband Instrumentation

The OPA658U-1 suits portable wideband instrumentation because it provides 900 MHz bandwidth while drawing only 5.7 uA quiescent current. That combination allows a compact 8-pin SOIC implementation in battery-operated or space-constrained equipment. The trade-off is that high-frequency analog design becomes more sensitive to resistor tolerances, capacitor selection, and board parasitics than a low-frequency precision amplifier. Designers should verify settling at the required signal rate, use a stable power supply, and keep the feedback network compact.

🏭

Industrial High-Speed Sensor Interface

The OPA658U-1 can serve as a high-speed interface for industrial sensors requiring bandwidth beyond the range of conventional precision op amps. Its 900 MHz bandwidth and 1700 V/us slew rate provide headroom for fast sensor waveforms and trigger events, while the 5.7 uA quiescent current reduces supply burden in distributed equipment. Place input and feedback components near the device, maintain a continuous ground return, and account for connector and cable resonances. The result is a compact analog channel suited to fast industrial monitoring systems.

🖥️

Low-Power Wideband Test and Measurement

The OPA658U-1 is useful in low-power wideband test and measurement circuits where 900 MHz bandwidth, 1700 V/us slew rate, and 5.7 uA quiescent current must coexist in a small package. It can form the output driver or input-conditioning stage of a compact measurement system. Use the manufacturer’s feedback recommendations as the starting point, and verify stability across resistor and capacitor tolerances. The principal benefit is high-frequency capability without the higher supply demand associated with many wideband amplifiers.

Resumen de productos recomendados

OPA828ID Texas Instruments Se usa en: High-Resolution Video Signal Conditioning, Medical Imaging Analog Front End, DAC Current-to-Voltage Conversion, Portable Wideband Instrumentation, Industrial High-Speed Sensor Interface, Low-Power Wideband Test and Measurement OPA658U Same-family SOIC amplifier Se usa en: High-Resolution Video Signal Conditioning, DAC Current-to-Voltage Conversion, Portable Wideband Instrumentation, Industrial High-Speed Sensor Interface OPA658U/2K5 Same-family SOIC ordering option Se usa en: Medical Imaging Analog Front End OPA658UB Same-family SOIC option Se usa en: Low-Power Wideband Test and Measurement
What are the key specifications of OPA658U-1 that engineers should know?
The OPA658U-1 is a single-channel current-feedback operational amplifier with 900 MHz bandwidth, 1700 V/us slew rate, 5.7 uA quiescent current, and an 8-pin SOIC package. According to the Texas Instruments OPA658 datasheet, its current-feedback architecture provides excellent large-signal response and wide bandwidth. The device is intended for ±5.5 V operation and is suited to high-resolution video, medical imaging, DAC current-to-voltage conversion, and portable applications.
What is the bandwidth and slew rate of the OPA658U-1?
The OPA658U-1 provides 900 MHz bandwidth and a 1700 V/us slew rate. These figures make it a wideband, low-power current-feedback operational amplifier for high-resolution video, medical imaging, and DAC current-to-voltage conversion. According to the Texas Instruments OPA658 datasheet, the current-feedback architecture combines wide bandwidth with excellent large-signal response rather than optimizing only for small-signal operation.
Why is the OPA658U-1 suitable for high-resolution video?
The OPA658U-1 is suitable for high-resolution video because its 900 MHz bandwidth supports high-speed signal paths and its current-feedback architecture provides strong large-signal response. The Texas Instruments OPA658 datasheet specifically identifies high-resolution video as a suitable application. Layout remains important: short feedback paths, low-inductance routing, and close supply decoupling help preserve the intended high-frequency behavior.
Can OPA658U-1 be used for DAC current-to-voltage conversion?
Yes, the OPA658U-1 can perform DAC current-to-voltage conversion because it combines a 900 MHz bandwidth with a 1700 V/us slew rate. The Texas Instruments OPA658 datasheet lists DAC I/V conversion as a key application. The external feedback resistor and output network establish the conversion gain, so their tolerance and layout must be included in the bandwidth and accuracy calculations.
Where can I download the OPA658U-1 datasheet PDF?
The OPA658U-1 datasheet PDF is available through the official Texas Instruments OPA658 datasheet hosted by Mouser at https://www.mouser.com/catalog/specsheets/opa658.pdf. The document describes the wideband, low-power current-feedback amplifier and includes its electrical characteristics, package information, and application guidance. Use the pin-description table in that document when assigning SOIC-8 connections and designing the feedback network.
Where can I find the OPA658U-1 pinout?
The OPA658U-1 pinout is shown in the pin-description table of the Texas Instruments OPA658 datasheet. The device uses an 8-pin SOIC package, and its standard pin assignments are 1 NC, 2 −IN, 3 +IN, 4 V−, 5 NC, 6 NC, 7 V+, and 8 OUT. Confirm the ordering-code package and pin compatibility against the datasheet before laying out a replacement PCB.
Is OPA658U-1 suitable for medical imaging and portable applications?
The OPA658U-1 is suitable for medical imaging and portable applications because it combines 900 MHz bandwidth with a low 5.7 uA quiescent current. The Texas Instruments OPA658 datasheet identifies medical imaging among its target applications and describes the low-power requirements as advantageous for portable equipment. Actual medical-device use still requires system-level validation of signal integrity, safety, and applicable regulatory requirements.
OPA658U-1 vs OPA658U - which is the better choice?
The OPA658U and OPA658U-1 are both identified as 8-pin SOIC versions of the same wideband, low-power current-feedback family. The OPA658U-1 listing confirms the same 900 MHz bandwidth, 1700 V/us slew rate, and 5.7 uA quiescent current. Their ordering suffix should therefore be checked primarily for package, temperature-grade, and ordering-code requirements rather than treated as a different amplifier architecture.
When should I choose OPA658U-1 over a lower-bandwidth operational amplifier?
Choose the OPA658U-1 when the signal path requires wide bandwidth, fast large-signal response, or low quiescent current simultaneously. Its 900 MHz bandwidth and 1700 V/us slew rate are substantially more demanding than general-purpose amplifiers. The trade-off is greater sensitivity to feedback-component selection, board parasitics, and layout quality, so a conventional slow-signal amplifier remains preferable when those requirements are absent.
Is OPA658U-1 suitable for low-power portable instrumentation?
The OPA658U-1 is suitable for low-power portable instrumentation because its quiescent current is 5.7 uA while its bandwidth is 900 MHz. The Texas Instruments OPA658 datasheet identifies numerous portable applications and emphasizes the combination of wideband performance and low power. The complete instrument signal chain, settling requirements, and duty cycle should be evaluated to determine whether the achieved system-level accuracy matches the measurement goal.
What is the best drop-in replacement for OPA658U-1?
The closest verified drop-in replacement is the OPA658U, which uses the same 8-pin SOIC package and matches the key published ratings of 900 MHz bandwidth, 1700 V/us slew rate, and 5.7 uA quiescent current. No fully documented cross-brand, pin-to-pin replacement was identified in the available cross-reference results. Verify the complete datasheet, including enable or shutdown behavior, supply range, stability requirements, and temperature grade, before substitution.
Can OPA658P replace OPA658U-1 without changing the PCB?
No, the OPA658P should not replace the OPA658U-1 without a PCB change because the OPA658P is specified as an 8-pin PDIP package, whereas the OPA658U-1 is an 8-pin SOIC device. The parts belong to the same amplifier family, but package geometry and lead spacing differ. The DIP and SOIC options therefore require separate PCB footprints and are not strict drop-in alternatives.
What is the best Analog Devices equivalent for OPA658U-1?
No Analog Devices equivalent can be recommended as a verified drop-in replacement from the available cross-reference information. A suitable cross-brand candidate must use the same 8-pin SOIC footprint, preserve pin-to-pin assignments, and remain within the important bandwidth, slew-rate, supply-voltage, noise, and stability requirements. Use the Request a Quote form on this page to request assistance with component sourcing and substitution review.
Where can I buy OPA658U-1 and what is its current price?
Use the Request a Quote form on this page to request current OPA658U-1 availability, commercial terms, and a volume quotation. The visible price field is populated from current structured pricing when qualifying quantity-break data is available; otherwise the page uses a dated reference price for context. Request the current lead time, minimum order quantity, and delivery schedule with the quotation.
How do I request the OPA658U-1 lead time and stock status?
Request the current OPA658U-1 lead time, stock status, and shipment schedule through the Request a Quote form on this page. The Texas Instruments OPA658U-1 is an 8-pin SOIC current-feedback operational amplifier with 900 MHz bandwidth, 1700 V/us slew rate, and 5.7 uA quiescent current. Include your required quantity, target delivery date, and approved-part list so the sourcing response can be matched to the actual production need.

Datos de referencia de ingeniería para OPA658U-1 — comparación, orientación de diseño e información de cumplimiento.

Guía de selección

Choose the OPA658U-1 when a high-speed analog channel needs 900 MHz bandwidth, 1700 V/us slew rate, and low 5.7 uA quiescent current in an 8-pin SOIC package. It is particularly appropriate for high-resolution video, medical imaging, DAC current-to-voltage conversion, portable instrumentation, and industrial sensor interfaces. Select the OPA658U when its ordering-code details satisfy the production requirements and the OPA658U-1 suffix is unnecessary. The OPA658UB is another same-package family option, but its exact grade distinctions should be confirmed before substitution. Do not choose the OPA658P for an existing OPA658U-1 board because its PDIP-8 package requires a different footprint. Because no cross-brand drop-in candidate was verified for the complete electrical and pin requirements, use a cross-brand alternative only after a detailed review of supply range, bandwidth, slew rate, noise, stability, enable behavior, and package geometry.

Comparación con alternativas

Parámetro Este producto OPA658U OPA658UB
Package 8-pin SOIC 8-pin SOIC 8-pin SOIC
Brand Texas Instruments Texas Instruments Texas Instruments
Amplifier Architecture Current feedback Current feedback Current feedback
Bandwidth 900 MHz 900 MHz 900 MHz
Slew Rate 1700 V/us 1700 V/us 1700 V/us
Quiescent Current 5.7 uA 5.7 uA 5.7 uA
Supply Voltage ±5.5 V ±5.5 V ±5.5 V
Number of Channels 1 channel 1 channel 1 channel
Number of Pins 8 pins 8 pins 8 pins
Primary Applications High-resolution video, medical imaging, DAC I/V conversion, portable equipment High-resolution video, medical imaging, DAC I/V conversion, portable equipment High-resolution video, medical imaging, DAC I/V conversion, portable equipment

Diferenciadores clave

  • Wideband current-feedback performance (frente a OPA658U)
  • Low quiescent current for a wideband amplifier (frente a OPA658UB)
  • Package-compatible service replacement (frente a OPA658P)

Notas de diseño

Place feedback resistors and their associated compensation capacitors directly beside the OPA658U-1 input pins. Keep the output route short, avoid broad loops between the amplifier and feedback network, and provide a continuous ground reference under the device. At 900 MHz, trace inductance, pad capacitance, and resistor parasitics can affect stability and peaking even when the nominal feedback values are correct.

Treat the complete feedback network as part of the amplifier design. Resistor tolerance, series inductance, and the impedance presented by the source or load can change the effective closed-loop bandwidth. Use the manufacturer’s recommended feedback values as the starting point, evaluate stability across tolerance extremes, and keep sensitive input nodes physically separate from high-current output and supply-return paths.

Decouple each supply connection close to the corresponding device pin and maintain low impedance from the capacitor to the package ground or supply return. The OPA658U-1 has a 5.7 uA quiescent current, but dynamic output current and external circuit loads can dominate total supply demand. Verify the power source can support the required signal amplitude without injecting supply noise into the output.

Do not substitute the OPA658P for the OPA658U-1 on an existing board. The OPA658P is a PDIP-8 device, while the OPA658U-1 uses an 8-pin SOIC footprint; changing between them requires a different PCB land pattern. Also check the complete ordering code for temperature-grade and qualification requirements instead of assuming every OPA658 suffix is interchangeable.

Información de cumplimiento

RoHS
Unknown
REACH
Unknown
AEC-Q100
Unknown
Libre de plomo
Unknown
Libre de halógenos
Unknown
Minerales en conflicto
Unknown

No definitive RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals declarations were present in the available product information.

Búsquedas relacionadas

OPA658U-1 datasheet OPA658U-1 pinout OPA658U-1 datasheet pdf OPA658U-1 SOIC-8 OPA658U-1 900MHz amplifier OPA658U-1 current feedback op amp OPA658U-1 DAC I/V conversion OPA658U-1 medical imaging amplifier OPA658U-1 replacement OPA658U-1 equivalent OPA658U-1 vs OPA658U Texas Instruments OPA658U-1 OPA658U-1 price OPA658U-1 stock OPA658U-1 application circuit

Componentes & términos relacionados

Texas Instruments OPA658U-1 OPA658U OPA658UB OPA658P OPA658U/2K5 current-feedback operational amplifier operational amplifier analog amplifier analog signal-conditioning IC semiconductor low-dropout regulator linear regulator voltage regulator power management IC 900 MHz bandwidth 1700 V/us slew rate 5.7 uA quiescent current ±5.5 V supply 8-pin SOIC SOIC family surface-mount package high-resolution video medical imaging DAC current-to-voltage conversion
RFQ de presupuesto rápido
Complete los detalles — nuestro equipo de ventas responderá en un plazo de 24 horas
Número de pieza Fabricante Encapsulado QTY Precio objetivo Total
✓
¡Presupuesto enviado!

Responderemos a su correo electrónico en un plazo de 24 horas

1
RFQ enviado
2
Presupuesto recibido
3
Pedido realizado
4
Pago
5
Enviado
6
Entregado
Ver detalles del RFQ