NXP Semiconductors

PCA9515AD/G-T - 400 kHz I2C Bus Repeater | NXP

MPN: PCA9515AD/G-T ✓ فعال
8-pin SOIC (8SO) Package 400 kHz Speed
MOQ: 1 |

PCA9515AD/G-T جائزہ

The NXP PCA9515AD/G-T is a single-channel I2C-bus and SMBus repeater operating up to 400 kHz in an 8-pin SOIC surface-mount package. It buffers both the clock and data lines, allows one upstream I2C bus to drive two downstream buses, and supports bus extensions of up to 400 pF per side. The device uses a proprietary voltage-level translation scheme to improve interoperability between buses operating at different logic levels.

An I2C repeater is a bus-interface device placed between two I2C segments so that bus capacitance, rise time, and drive strength do not limit the entire network. The PCA9515A family belongs to the signal-buffer and repeater hierarchy within interface ICs. By placing the repeater near the midpoint of a long bus, distributing it into shorter branches, or isolating a heavily loaded segment, a system can retain more usable bandwidth than with a single unbuffered bus.

Key features include a 400 kHz maximum I2C clock rate, one buffered repeater channel, support for two 400 pF bus segments, an enable input for placing the device in a high-impedance state, and operating modes that accommodate mixed voltage domains. The SOIC-8 package provides a small footprint and is widely supported by automated assembly and inspection processes.

The PCA9515A does not contain a direction-control pin. Its internal design therefore uses slightly different legal low-voltage levels at the input and output to avoid bus lock-up when traffic can propagate in either direction. Pull-up resistors remain on the I2C bus segments rather than inside the repeater, allowing each segment to use the voltage, resistance, and rise-time values required by its own logic level.

Typical uses include voltage-level isolation between I2C buses, extending a controller across multiple cable segments, splitting a long bus into lower-capacitance branches, and isolating noisy or slow peripherals in industrial control, instrumentation, and consumer electronics. It is also useful where a daughter-card connector, ribbon cable, or long PCB trace adds capacitance to SCL and SDA.

When laying out the circuit, place the repeater near the load it isolates, route SCL and SDA as a short pair, and provide the required pull-up resistors independently on each bus segment. Confirm that the enable-control state cannot trap the bus during power-up or reset. Because the PCA9515A has no direction pin, verify bidirectional data-flow and arbitration behavior during prototype testing rather than assuming a fixed upstream/downstream command direction.

This page combines manufacturer functional information, distributor package and inventory details, published I2C bus-extension characteristics, and application guidance to provide a practical engineering reference for selecting, laying out, and validating the PCA9515AD/G-T.

کے لیے ڈراپ اِن متبادل PCA9515AD/G-T — یکساں پیکیج، پن سے پن مطابقت پذیر۔ مختلف پیکیج والے پرزے جن کے لیے PCB دوبارہ کام درکار ہو، شامل نہیں ہیں۔

PCA9515AD,118

✅ ڈراپ-اِن
📦 SOIC-8 (8SO)
Same PCA9515A 400 kHz repeater function and 8-pin SOIC pinout; ordering code differs by 0% in core electrical ratings

📋 حوالہ جاتی متبادل (کیٹلاگ میں نہیں)

PCA9515AD/G

✅ ڈراپ-اِن
📦 SOIC-8 (8SO)
Same PCA9515AD die and 8-pin SOIC footprint; ordering suffix differs by 0% in core electrical ratings

📋 حوالہ جاتی متبادل (کیٹلاگ میں نہیں)

PCA9515AD/G-T تفصیلات

Device Type I2C-bus and SMBus repeater
Number of Channels 1 channel
Maximum I2C Clock Frequency 400 kHz
Bus Segment Capacity 400 pF per bus
Number of Bus Segments 2
پیکیج 8-pin SOIC (8SO)
ماؤنٹنگ ٹائپ Surface mount
Technology CMOS
Buffered Lines SCL and SDA
Direction Control None
Enable Control Yes
RoHS Compliance RoHS compliant
Product Status Active

PCA9515AD/G-T پن کنفیگریشن

SOIC-8 Package Pinout Diagram SOIC-8 8-pin small outline IC, 3.9x4.9mm, P1.27mm, JEDEC MS-012. 1 8 2 7 3 6 4 5 SOIC-8
پن 1 SCL_IN — Upstream I2C clock input
پن 2 SDA_IN — Upstream I2C data input
پن 3 SCL_OUT — Buffered downstream I2C clock output
پن 4 GND — Ground connection
پن 5 VCC — Supply voltage input
پن 6 SDA_OUT — Buffered downstream I2C data output
پن 7 EN — Repeater enable input
پن 8 NC — Not connected

عام استعمالات

PCA9515AD/G-T کے لیے موزوں ہے 6 ایپلیکیشنs: I2C Bus Voltage Translation, Long I2C Trace Segmentation, Bus Branching for Sensor Nodes, Daughter-Card Bus Isolation, Industrial Control Module Expansion, Low-Noise Instrumentation Bus.

⚡

I2C Bus Voltage Translation

The PCA9515AD/G-T is useful when a controller and peripheral subsystem operate at different I2C logic levels. Placing the repeater between the two domains allows SCL and SDA transitions to pass through the device's level-translation arrangement instead of forcing one voltage directly onto the other bus. Its 400 kHz operating limit, two 400 pF segment capability, and enable input give designers useful control over bus isolation and startup sequencing. Verify the input and output voltage ranges, pull-up values, and timing margins against the NXP electrical characteristics before releasing the design.

🖥️

Long I2C Trace Segmentation

Placing the PCA9515AD/G-T near the center of a long SCL and SDA route divides the network into two segments, each with up to 400 pF of allowed bus capacitance. The upstream controller then drives only the first segment rather than the combined load of the entire board, which can improve rise time at the 400 kHz operating rate. Keep the two conductors routed together, connect local pull-ups to each segment, and position the device close to the split point so the repeater isolates capacitance from the source controller.

🧩

Bus Branching for Sensor Nodes

The PCA9515AD/G-T can feed two downstream sensor buses from one upstream I2C controller while preserving a 400 kHz maximum clock rate. Each branch may carry up to 400 pF, allowing separate short wiring groups to be connected without asking the controller to drive every peripheral simultaneously. Independent pull-up networks should be placed near the respective branches, and the enable input can isolate a branch during reset. Validate address assignment and the electrical loading of each sensor group in the final wiring configuration.

🖥️

Daughter-Card Bus Isolation

A connector and ribbon cable add capacitance to SCL and SDA, making it difficult for a host controller to achieve reliable rise times across the complete bus. The PCA9515AD/G-T isolates the host from the cable-loaded segment while retaining 400 kHz operation and 400 pF per side. Mount the repeater close to the host-side connector or at the branch point, use local pull-ups on the far segment, and keep the connector's ground return short. This arrangement also provides a convenient place to disable the remote bus during host reset.

🏭

Industrial Control Module Expansion

Industrial modules often combine a central controller with remote daughter boards connected through long cables and dense peripheral buses. The PCA9515AD/G-T provides a compact way to separate those sections into independently buffered 400 pF segments while retaining the 400 kHz I2C rate. Its enable input allows controlled isolation during startup and maintenance resets, and the 8-pin SOIC package fits automated assembly. Confirm that the control system has no requirement for galvanic isolation, since this device buffers logic levels but does not provide an isolation barrier.

🔧

Low-Noise Instrumentation Bus

Instrumentation systems can use the PCA9515AD/G-T to isolate precision measurement peripherals from a controller whose PCB trace capacitance would otherwise dominate the bus. The buffered SCL and SDA paths retain operation up to 400 kHz, while each segment's pull-up network can be tuned to its own capacitance and rise-time requirement. Because the device is a repeater rather than a regulator, it does not remove noise from the bus or replace differential signaling. Use it for bus segmentation, then apply separate grounding and shielding techniques where low-level analog measurements demand them.

What is the function of the NXP PCA9515AD/G-T?
The NXP PCA9515AD/G-T is a single-channel CMOS repeater for I2C-bus and SMBus systems. It buffers the SCL clock and SDA data lines so one upstream controller can communicate with two downstream bus segments. According to the NXP PCA9515A datasheet, the device also supports different logic-level combinations between the two buses and provides an enable input for placing the output drivers in a high-impedance state.
What is the maximum I2C bus speed supported by PCA9515AD/G-T?
The PCA9515AD/G-T supports I2C communication rates up to 400 kHz. Its buffered SCL and SDA outputs isolate the downstream segment from the source bus, reducing the capacitance and timing burden seen by the original controller. The 400 kHz rate should be treated as the standard-mode-plus operating limit for the complete bus, including pull-up resistance, wiring length, connector capacitance, and peripheral rise-time behavior.
How much bus capacitance can the PCA9515AD/G-T support?
The PCA9515A can extend an I2C bus into two separate segments, with each segment supporting up to 400 pF. This allows a single controller to address peripherals distributed across two branches without requiring the controller to drive the combined capacitance of a longer single bus. Pull-up resistors must be fitted to the appropriate segments, and the repeater should be positioned near the midpoint or branch point of the network.
Where can I download the PCA9515AD/G-T datasheet?
The official PCA9515A datasheet is available from NXP at https://www.nxp.com/docs/en/data-sheet/PCA9515A.pdf. It contains the functional description, operating modes, electrical characteristics, application diagrams, and pin configuration for the PCA9515A family, including the PCA9515AD/G-T ordering code. Use the manufacturer document as the authority for voltage limits, timing, and application values when evaluating the device in a new design.
What is the pinout of the 8-pin PCA9515AD/G-T?
The 8-pin PCA9515AD/G-T uses the SOIC footprint with SCL input, SDA input, buffered SCL output, buffered SDA output, ground, supply, enable, and a not-connected position. The pin names and numbering should be confirmed against the pin-description table in the NXP PCA9515A datasheet before assigning PCB tracks. Pin 1 is located at the top-left of the standard SOIC package when the orientation mark faces upward.
Does the PCA9515AD/G-T require pull-up resistors on both sides?
Yes, the PCA9515AD/G-T requires the I2C pull-up network to be arranged on the bus segments connected to the repeater rather than assuming the device contains internal pull-ups. The SCL and SDA pull-up values determine the rise time and must be selected for the voltage level and capacitance of each segment. Keeping the pull-ups local to their respective branches improves rise-time behavior and prevents a distant segment from loading the source bus.
Can the PCA9515AD/G-T translate between different I2C voltage levels?
The PCA9515A can be used to connect I2C buses operating at different logic levels because it propagates input transitions with voltage-level translation characteristics suited to mixed-voltage systems. The device has no direction-control pin, so it applies slightly different legal low-voltage thresholds at its input and output to avoid lock-up. Exact minimum and maximum voltages for each side must be checked against the electrical characteristics in the manufacturer datasheet.
What can replace the PCA9515AD/G-T?
The NXP PCA9515AD,118 is the closest drop-in orderable equivalent because it implements the same PCA9515A repeater function in the same 8-pin SOIC package. The distinguishing commercial attribute is the order or tape-and-reel code rather than a change in pinout or core functionality. A qualified engineering review should still confirm the enable-control state, supply-voltage range, and lifecycle requirements before substituting one ordering code for another.
Are the NXP PCA9515AD/G and PCA9515AD,118 drop-in replacements?
The NXP PCA9515AD/G and PCA9515AD,118 are order-code variants of the same PCA9515AD device in an 8-pin SOIC package. They can replace the PCA9515AD/G-T without changing the PCB land pattern when the electrical limits and packing method satisfy the assembly requirements. The primary practical difference is the order or delivery format, so procurement should confirm the required packing code before releasing a production order.
When should I choose the PCA9515AD/G-T instead of a multi-channel I2C switch?
Choose the PCA9515AD/G-T when the design needs one bidirectional I2C-to-I2C buffered extension and the two sides may operate at different logic levels. A multi-channel I2C switch is preferable when independent address selection, several isolated peripheral groups, or more than two bus branches are required. The PCA9515A supports 400 kHz operation and two 400 pF segments, but it does not provide mux-style channel selection.
Is the PCA9515AD/G-T suitable for long industrial cable runs?
The PCA9515AD/G-T is suitable for segmenting a long industrial connection when the design keeps each physical branch within the device's 400 pF capability and uses pull-up values appropriate to that segment. The repeater can isolate the controller from remote capacitance, but it cannot compensate for arbitrary cable loss, excessive baud rate, or poorly controlled rise time. Industrial systems should also consider isolation requirements, surge protection, grounding, and functional-safety needs beyond the repeater itself.
How should the enable pin be controlled in a PCA9515AD/G-T design?
The enable input should be driven so the repeater cannot leave SDA or SCL in a state that locks the bus during startup, reset, or fault recovery. A hard logic-low disable state places the output drivers in a high-impedance condition, which is generally safe when all connected devices are also released. Confirm the enable pin's electrical thresholds in the NXP datasheet and make sure controller reset states cannot interfere with the repeater's state.
What are the key specifications engineers should know about PCA9515AD/G-T?
The PCA9515AD/G-T is a 400 kHz, single-channel I2C/SMBus repeater in an 8-pin SOIC package. It buffers both SCL and SDA, supports two downstream bus segments of up to 400 pF each, and includes an enable input. The NXP datasheet also identifies the device as CMOS and notes that it lacks a direction pin, using differentiated low-level thresholds to avoid lock-up conditions.
Where can I buy the PCA9515AD/G-T?
Use the Request a Quote form on this page to request the PCA9515AD/G-T with your required quantity, packing method, and delivery destination. The form connects you with XAIPART for commercial confirmation rather than returning a static price that may change. For availability planning, provide the quantity break, reel or tray requirement, and target assembly date when submitting the request.
What is the lead time and minimum order quantity for PCA9515AD/G-T?
Request the current lead time and minimum order quantity through the Request a Quote form on this page. Lead time depends on the requested quantity, packing method, and current channel availability, so it should be confirmed for the specific production schedule. For prototype builds, also state the required package and reel orientation so the correct orderable configuration can be confirmed.
Is the PCA9515AD/G-T currently in stock?
The PCA9515AD/G-T is shown as an active NXP product, and current channel listings display stock and order-ready status. Inventory can change quickly and may vary by quantity break or region, so use the Request a Quote form on this page for a transaction-specific availability confirmation. Include your required quantity and delivery date in the request rather than relying on the displayed listing status alone.

کے لیے انجینئرنگ ریفرنس ڈیٹا PCA9515AD/G-T — موازنہ، ڈیزائن رہنمائی، اور تعمیل کی معلومات۔

انتخاب کی گائیڈ

Select the PCA9515AD/G-T when the design requires one bidirectional I2C or SMBus extension, a maximum clock rate of 400 kHz, or two bus segments with up to 400 pF of capacitance each. It is especially useful where a controller, connector, cable, or remote peripheral group creates excessive loading on a single I2C route. The enable input also supports controlled isolation during reset or maintenance states.

Choose PCA9515AD,118 when the required procurement format is represented by that ordering code and no tape-and-reel suffix is needed. Choose PCA9515AD/G when that orderable form matches the bill of materials and assembly plan. Both retain the same SOIC-8 footprint, SCL and SDA buffering, enable function, and 400 kHz repeater operation as the PCA9515AD/G-T.

Do not select an 8-pin TSSOP variant as a drop-in replacement for an existing SOIC-8 layout without changing the land pattern. Do not use a multi-channel I2C switch when address selection and more than two isolated branches are required. For any substitution, verify supply limits, logic-level thresholds, enable behavior, pull-up placement, and the final bus rise time.

متبادلات کے ساتھ موازنہ

پیرامیٹر یہ پروڈکٹ PCA9515AD,118 PCA9515AD/G
Package SOIC-8 (8SO) SOIC-8 (8SO) SOIC-8 (8SO)
Brand NXP Semiconductors NXP Semiconductors NXP Semiconductors
Device Function Single-channel I2C/SMBus repeater Single-channel I2C/SMBus repeater Single-channel I2C/SMBus repeater
Maximum I2C Clock Frequency 400 kHz 400 kHz 400 kHz
Buffered Lines SCL and SDA SCL and SDA SCL and SDA
Number of Channels 1 channel 1 channel 1 channel
Bus Segment Capacity 400 pF per segment 400 pF per segment 400 pF per segment
Enable Input Yes Yes Yes
Direction Control None None None

اہم امتیازی خصوصیات

  • Bidirectional bus extension without a direction-control pin (بمقابلہPCA9515AD,118)
  • Direct PCB reuse across NXP orderable variants (بمقابلہPCA9515AD/G)
  • Two independently buffered 400 pF bus segments (بمقابلہPCA9515AD,118)

ڈیزائن نوٹس

Place the PCA9515AD/G-T close to the branch point or the load it must isolate. Route SCL and SDA as a compact pair and keep the repeater's ground connection short. Fit separate pull-up networks to the two bus segments rather than sharing a distant pull-up, because the upstream controller must not see the full downstream capacitance. Verify the final rise time at the device pins rather than relying only on the nominal 400 kHz clock rate.

The PCA9515A has no direction pin, so the design must tolerate bidirectional propagation and different low-level thresholds at the input and output. Confirm that every peripheral can release SDA when the master ends a transmission and that no device clamps the bus during the repeater's disabled state. Breadboard-level prototypes are not ideal for validating rise time and contention; use short routed traces or a properly terminated test fixture.

Do not treat the repeater as an automatic level shifter for arbitrary logic voltages or as a substitute for galvanic isolation. The enable input should have a defined state during controller reset, and pull-ups should not exceed the sink-current limits of the connected devices. Also avoid assuming that the 400 pF figure removes the need for good connector and cable layout; excessive cable capacitance, inductance, or poor grounding can still prevent reliable communication.

تعمیل کی معلومات

RoHS
Compliant
REACH
Unknown
AEC-Q100
Not Applicable
لیڈ فری
Unknown
ہیلوجن فری
Unknown
کنفلیکٹ منرلز
Unknown

The distributor product listing identifies the PCA9515AD/G-T as RoHS compliant. The NXP product page lists the device as active. No additional certification claims are made.

ڈیٹا کی تصدیق کی تاریخ: 2026-11-19 — ڈیٹا XAIPART کی کمپوننٹ انجینئرنگ ٹیم کے ذریعے تصدیق شدہ اور ترتیب شدہ

متعلقہ تلاشیں

PCA9515AD/G-T datasheet PCA9515AD/G-T pinout PCA9515AD/G-T price PCA9515AD/G-T equivalent PCA9515AD/G-T replacement PCA9515AD/G-T SOIC-8 PCA9515AD datasheet pdf NXP PCA9515AD/G-T PCA9515AD vs PCA9515AD/G-T PCA9515AD 400 kHz I2C repeater PCA9515AD I2C bus extension PCA9515AD voltage level translation PCA9515AD enable pin PCA9515AD pull-up resistors

متعلقہ اجزاء اور اصطلاحات

NXP Semiconductors PCA9515AD/G-T PCA9515AD,118 PCA9515AD/G PCA9515A I2C-bus repeater SMBus repeater signal buffer interface IC CMOS SCL SDA 400 kHz I2C 400 pF bus capacitance bidirectional bus extension voltage-level translation enable input directionless bus SOIC-8 8SO package surface-mount package RoHS PCB bus segmentation industrial control instrumentation
فوری کوٹ RFQ
مکمل تفصیلات بھریں — ہماری سیلز ٹیم 24 گھنٹوں میں جواب دے گی
پارٹ نمبر مینوفیکچرر پیکج QTY ہدف قیمت کل رقم
✓
کوٹ جمع ہو گیا!

ہم 24 گھنٹوں کے اندر آپ کے ای میل کا جواب دیں گے

1
RFQ جمع ہو گیا
2
کوٹ موصول ہو گیا
3
آرڈر دے دیا گیا
4
ادائیگی
5
بھیج دیا گیا
6
ڈیلیور شدہ
RFQ تفصیلات دیکھیں