PCA9515AD/G-T - 400 kHz I2C Bus Repeater | NXP
料号: PCA9515AD/G-T ✓ 量产中PCA9515AD/G-T 概述
An I2C repeater is a bus-interface device placed between two I2C segments so that bus capacitance, rise time, and drive strength do not limit the entire network. The PCA9515A family belongs to the signal-buffer and repeater hierarchy within interface ICs. By placing the repeater near the midpoint of a long bus, distributing it into shorter branches, or isolating a heavily loaded segment, a system can retain more usable bandwidth than with a single unbuffered bus.
Key features include a 400 kHz maximum I2C clock rate, one buffered repeater channel, support for two 400 pF bus segments, an enable input for placing the device in a high-impedance state, and operating modes that accommodate mixed voltage domains. The SOIC-8 package provides a small footprint and is widely supported by automated assembly and inspection processes.
The PCA9515A does not contain a direction-control pin. Its internal design therefore uses slightly different legal low-voltage levels at the input and output to avoid bus lock-up when traffic can propagate in either direction. Pull-up resistors remain on the I2C bus segments rather than inside the repeater, allowing each segment to use the voltage, resistance, and rise-time values required by its own logic level.
Typical uses include voltage-level isolation between I2C buses, extending a controller across multiple cable segments, splitting a long bus into lower-capacitance branches, and isolating noisy or slow peripherals in industrial control, instrumentation, and consumer electronics. It is also useful where a daughter-card connector, ribbon cable, or long PCB trace adds capacitance to SCL and SDA.
When laying out the circuit, place the repeater near the load it isolates, route SCL and SDA as a short pair, and provide the required pull-up resistors independently on each bus segment. Confirm that the enable-control state cannot trap the bus during power-up or reset. Because the PCA9515A has no direction pin, verify bidirectional data-flow and arbitration behavior during prototype testing rather than assuming a fixed upstream/downstream command direction.
This page combines manufacturer functional information, distributor package and inventory details, published I2C bus-extension characteristics, and application guidance to provide a practical engineering reference for selecting, laying out, and validating the PCA9515AD/G-T.
直接替换替代料: PCA9515AD/G-T ——相同封装,引脚兼容。需要 PCB 改动的不同封装料号已排除。
PCA9515AD,118
✅ 直接替换📋 参考替代料(不在目录中)
PCA9515AD/G
✅ 直接替换📋 参考替代料(不在目录中)
PCA9515AD/G-T 规格参数
| Device Type | I2C-bus and SMBus repeater |
| Number of Channels | 1 channel |
| Maximum I2C Clock Frequency | 400 kHz |
| Bus Segment Capacity | 400 pF per bus |
| Number of Bus Segments | 2 |
| 封装 | 8-pin SOIC (8SO) |
| 安装类型 | Surface mount |
| Technology | CMOS |
| Buffered Lines | SCL and SDA |
| Direction Control | None |
| Enable Control | Yes |
| RoHS Compliance | RoHS compliant |
| Product Status | Active |
PCA9515AD/G-T 引脚配置
| 引脚 1 | SCL_IN — Upstream I2C clock input |
| 引脚 2 | SDA_IN — Upstream I2C data input |
| 引脚 3 | SCL_OUT — Buffered downstream I2C clock output |
| 引脚 4 | GND — Ground connection |
| 引脚 5 | VCC — Supply voltage input |
| 引脚 6 | SDA_OUT — Buffered downstream I2C data output |
| 引脚 7 | EN — Repeater enable input |
| 引脚 8 | NC — Not connected |
典型应用
PCA9515AD/G-T 适用于 6 应用s: I2C Bus Voltage Translation, Long I2C Trace Segmentation, Bus Branching for Sensor Nodes, Daughter-Card Bus Isolation, Industrial Control Module Expansion, Low-Noise Instrumentation Bus.
I2C Bus Voltage Translation
The PCA9515AD/G-T is useful when a controller and peripheral subsystem operate at different I2C logic levels. Placing the repeater between the two domains allows SCL and SDA transitions to pass through the device's level-translation arrangement instead of forcing one voltage directly onto the other bus. Its 400 kHz operating limit, two 400 pF segment capability, and enable input give designers useful control over bus isolation and startup sequencing. Verify the input and output voltage ranges, pull-up values, and timing margins against the NXP electrical characteristics before releasing the design.
推荐
Long I2C Trace Segmentation
Placing the PCA9515AD/G-T near the center of a long SCL and SDA route divides the network into two segments, each with up to 400 pF of allowed bus capacitance. The upstream controller then drives only the first segment rather than the combined load of the entire board, which can improve rise time at the 400 kHz operating rate. Keep the two conductors routed together, connect local pull-ups to each segment, and position the device close to the split point so the repeater isolates capacitance from the source controller.
推荐
Bus Branching for Sensor Nodes
The PCA9515AD/G-T can feed two downstream sensor buses from one upstream I2C controller while preserving a 400 kHz maximum clock rate. Each branch may carry up to 400 pF, allowing separate short wiring groups to be connected without asking the controller to drive every peripheral simultaneously. Independent pull-up networks should be placed near the respective branches, and the enable input can isolate a branch during reset. Validate address assignment and the electrical loading of each sensor group in the final wiring configuration.
推荐
Daughter-Card Bus Isolation
A connector and ribbon cable add capacitance to SCL and SDA, making it difficult for a host controller to achieve reliable rise times across the complete bus. The PCA9515AD/G-T isolates the host from the cable-loaded segment while retaining 400 kHz operation and 400 pF per side. Mount the repeater close to the host-side connector or at the branch point, use local pull-ups on the far segment, and keep the connector's ground return short. This arrangement also provides a convenient place to disable the remote bus during host reset.
推荐
Industrial Control Module Expansion
Industrial modules often combine a central controller with remote daughter boards connected through long cables and dense peripheral buses. The PCA9515AD/G-T provides a compact way to separate those sections into independently buffered 400 pF segments while retaining the 400 kHz I2C rate. Its enable input allows controlled isolation during startup and maintenance resets, and the 8-pin SOIC package fits automated assembly. Confirm that the control system has no requirement for galvanic isolation, since this device buffers logic levels but does not provide an isolation barrier.
推荐
Low-Noise Instrumentation Bus
Instrumentation systems can use the PCA9515AD/G-T to isolate precision measurement peripherals from a controller whose PCB trace capacitance would otherwise dominate the bus. The buffered SCL and SDA paths retain operation up to 400 kHz, while each segment's pull-up network can be tuned to its own capacitance and rise-time requirement. Because the device is a repeater rather than a regulator, it does not remove noise from the bus or replace differential signaling. Use it for bus segmentation, then apply separate grounding and shielding techniques where low-level analog measurements demand them.
推荐
推荐产品汇总
工程参考数据: PCA9515AD/G-T ——对比、设计指导和合规信息。
选型指南
Choose PCA9515AD,118 when the required procurement format is represented by that ordering code and no tape-and-reel suffix is needed. Choose PCA9515AD/G when that orderable form matches the bill of materials and assembly plan. Both retain the same SOIC-8 footprint, SCL and SDA buffering, enable function, and 400 kHz repeater operation as the PCA9515AD/G-T.
Do not select an 8-pin TSSOP variant as a drop-in replacement for an existing SOIC-8 layout without changing the land pattern. Do not use a multi-channel I2C switch when address selection and more than two isolated branches are required. For any substitution, verify supply limits, logic-level thresholds, enable behavior, pull-up placement, and the final bus rise time.
与替代料对比
| 参数 | 本产品 | PCA9515AD,118 | PCA9515AD/G |
|---|---|---|---|
| Package | SOIC-8 (8SO) | SOIC-8 (8SO) | SOIC-8 (8SO) |
| Brand | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors |
| Device Function | Single-channel I2C/SMBus repeater | Single-channel I2C/SMBus repeater | Single-channel I2C/SMBus repeater |
| Maximum I2C Clock Frequency | 400 kHz | 400 kHz | 400 kHz |
| Buffered Lines | SCL and SDA | SCL and SDA | SCL and SDA |
| Number of Channels | 1 channel | 1 channel | 1 channel |
| Bus Segment Capacity | 400 pF per segment | 400 pF per segment | 400 pF per segment |
| Enable Input | Yes | Yes | Yes |
| Direction Control | None | None | None |
关键差异点
- Bidirectional bus extension without a direction-control pin (对比 PCA9515AD,118)
- Direct PCB reuse across NXP orderable variants (对比 PCA9515AD/G)
- Two independently buffered 400 pF bus segments (对比 PCA9515AD,118)
设计说明
Place the PCA9515AD/G-T close to the branch point or the load it must isolate. Route SCL and SDA as a compact pair and keep the repeater's ground connection short. Fit separate pull-up networks to the two bus segments rather than sharing a distant pull-up, because the upstream controller must not see the full downstream capacitance. Verify the final rise time at the device pins rather than relying only on the nominal 400 kHz clock rate.
The PCA9515A has no direction pin, so the design must tolerate bidirectional propagation and different low-level thresholds at the input and output. Confirm that every peripheral can release SDA when the master ends a transmission and that no device clamps the bus during the repeater's disabled state. Breadboard-level prototypes are not ideal for validating rise time and contention; use short routed traces or a properly terminated test fixture.
Do not treat the repeater as an automatic level shifter for arbitrary logic voltages or as a substitute for galvanic isolation. The enable input should have a defined state during controller reset, and pull-ups should not exceed the sink-current limits of the connected devices. Also avoid assuming that the 400 pF figure removes the need for good connector and cable layout; excessive cable capacitance, inductance, or poor grounding can still prevent reliable communication.
合规信息
The distributor product listing identifies the PCA9515AD/G-T as RoHS compliant. The NXP product page lists the device as active. No additional certification claims are made.