PIC16LF877AT-I/PT - 8-bit MCU, 14KB Flash, 33 I/O, 44-TQFP | Microchip
MPN: PIC16LF877AT-I/PT ✓ فعالPIC16LF877AT-I/PT جائزہ
An 8-bit microcontroller (MCU) is a single-chip computer that integrates a CPU, program memory (Flash/ROM), data memory (RAM), and peripherals (timers, ADC, communication ports) into one IC. PIC microcontrollers sit in the 8-bit MCU hierarchy: microcontroller -> embedded controller -> semiconductor IC, and serve as the "decision makers" in embedded products from coffee makers to industrial drives. The 16F family is Microchip's mid-range 8-bit line with a 14-bit instruction word and 35 single-word instructions, enabling extremely compact code and deterministic interrupt response.
Key features of the PIC16LF877AT-I/PT include: a 20 MHz maximum operating frequency (200 ns instruction cycle), a 10-bit ADC with up to 8 channels, two analog comparators, a Capture/Compare/PWM (CCP) module, enhanced Enhanced Universal Synchronous Asynchronous Receiver Transmitter (EUSART), Master Synchronous Serial Port (MSSP) supporting SPI and I2C, two 8-bit timers plus one 16-bit timer, a watchdog timer, in-circuit serial programming (ICSP), and nanoWatt power management with multiple sleep modes.
The 20 MHz core paired with a 14-bit instruction word delivers approximately 5 MIPS of throughput, while the wide 2.0V-5.5V supply range allows direct operation from a single Li-Ion cell, two AA cells, or a regulated 3.3V/5V rail. Internal oscillators and PLL trimming on the LF variant further reduce external component count, simplifying layout for space-constrained designs.
Typical applications include industrial sensor interfaces, motor-control front ends, low-power data acquisition nodes, automotive body electronics (non-safety), and consumer appliance controllers. The 44-pin TQFP exposes up to 33 digital I/O, sufficient for keypad scanning, LCD driving, and parallel bus bridging. Designers value this device for migration paths from older PIC16F877 designs that need lower voltage operation or a tape-and-reel SMD footprint.
When designing with this part, allocate the oscillator and ICSP pins (OSC1/CLK, OSC2/CLKOUT, RB6/PGC, RB7/PGD) on dedicated PCB traces and add a 100 nF decoupling capacitor within 5 mm of VDD. Avoid mapping analog inputs to pins used by the comparator outputs without verifying alternate-function routing, and respect VDD/VSS pairing for the 44-pin TQFP power pins.
کے لیے ڈراپ اِن متبادل PIC16LF877AT-I/PT — یکساں پیکیج، پن سے پن مطابقت پذیر۔ مختلف پیکیج والے پرزے جن کے لیے PCB دوبارہ کام درکار ہو، شامل نہیں ہیں۔
اس سیریز میں مختلف ورژن
اسی سیریز کے ماڈلز جو ڈراپ اِن مطابقت رکھتے ہیں PIC16LF877AT-I/PT (یکساں فارم فیکٹر اور فٹ پرنٹ) — میں مختلف Package, Timers, Serial Interfaces, Mounting Type, Operating Temperature.
PIC16LF877A-I/PT
✅ ڈراپ-اِنقیمت کے لیے رابطہ کریں
ڈیٹا شیٹ دیکھیں →PIC16F877AT-I/PT
✅ ڈراپ-اِنقیمت کے لیے رابطہ کریں
ڈیٹا شیٹ دیکھیں →PIC16LF877-04I/PT
✅ ڈراپ-اِنقیمت کے لیے رابطہ کریں
ڈیٹا شیٹ دیکھیں →PIC16LF877A-I/P
✅ ڈراپ-اِن ⚠️ تفصیلات غیر تصدیق شدہقیمت کے لیے رابطہ کریں
ڈیٹا شیٹ دیکھیں →PIC16F877A-E/L
✅ ڈراپ-اِن ⚠️ تفصیلات غیر تصدیق شدہقیمت کے لیے رابطہ کریں
ڈیٹا شیٹ دیکھیں →PIC16LF877AT-I/PT زیادہ سے زیادہ ریٹنگز اور برقی خصوصیات
| Core Architecture | PIC16 8-bit RISC |
| Instruction Word Size | 14-bit |
| Maximum CPU Frequency | 20 MHz |
| Program Memory (Flash) | 14 KB (8K x 14 words) |
| Data RAM | 368 bytes |
| Data EEPROM | 256 bytes |
| Supply Voltage (VDD) | 2.0 V to 5.5 V |
| Number of I/O Pins | 33 |
| ADC | 10-bit, up to 8 channels |
| Timers | 2 x 8-bit, 1 x 16-bit |
| Communication | EUSART, MSSP (SPI/I2C) |
| آپریٹنگ درجہ حرارت | -40 C to +85 C (Industrial) |
| پیکیج | 44-pin TQFP (10x10 mm) |
| ماؤنٹنگ ٹائپ | Surface Mount (Tape & Reel) |
| ICSP / Debug | In-Circuit Serial Programming supported |
| Power-Saving Modes | nanoWatt (Sleep, low-power instructions) |
PIC16LF877AT-I/PT پن کنفیگریشن
| پن 1 | MCLR/VPP/RE3 — Master Clear (reset) input / programming voltage / PORTE bit 3 |
| پن 2 | RA0/AN0 — PORTA bit 0 / analog input channel 0 |
| پن 3 | RA1/AN1 — PORTA bit 1 / analog input channel 1 |
| پن 4 | RA2/AN2/VREF- — PORTA bit 2 / analog input 2 / ADC VREF- |
| پن 5 | RA3/AN3/VREF+ — PORTA bit 3 / analog input 3 / ADC VREF+ |
| پن 6 | RA4/T0CKI/C1OUT — PORTA bit 4 / Timer0 clock / comparator 1 output |
| پن 7 | RA5/AN4/SS/C2OUT — PORTA bit 5 / analog 4 / SPI slave select / comparator 2 output |
| پن 8 | RE0/RD/AN5 — PORTE bit 0 / parallel read / analog 5 |
| پن 9 | RE1/WR/AN6 — PORTE bit 1 / parallel write / analog 6 |
| پن 10 | RE2/CS/AN7 — PORTE bit 2 / parallel chip select / analog 7 |
| پن 11 | VDD — Positive supply (2.0-5.5 V) |
| پن 12 | VSS — Ground |
| پن 13 | OSC1/CLKI — Crystal oscillator input / external clock |
| پن 14 | OSC2/CLKO — Crystal oscillator output / clock out |
| پن 15 | RC0/T1OSO/T1CKI — PORTC bit 0 / Timer1 oscillator out / Timer1 clock in |
| پن 16 | RC1/T1OSI/CCP2 — PORTC bit 1 / Timer1 oscillator in / CCP2 |
| پن 17 | RC2/CCP1 — PORTC bit 2 / CCP1 (PWM/capture/compare) |
| پن 18 | RC3/SCK/SCL — PORTC bit 3 / SPI clock / I2C clock |
| پن 19 | RD0 — PORTD bit 0 |
| پن 20 | RD1 — PORTD bit 1 |
| پن 21 | RD2 — PORTD bit 2 |
| پن 22 | RD3 — PORTD bit 3 |
| پن 23 | RC4/SDI/SDA — PORTC bit 4 / SPI data in / I2C data |
| پن 24 | RC5/SDO — PORTC bit 5 / SPI data out |
| پن 25 | RC6/TX/CK — PORTC bit 6 / EUSART TX / clock |
| پن 26 | RC7/RX/DT — PORTC bit 7 / EUSART RX / data |
| پن 27 | RD4 — PORTD bit 4 |
| پن 28 | RD5 — PORTD bit 5 |
| پن 29 | RD6/PSP6 — PORTD bit 6 / parallel slave port |
| پن 30 | RD7/PSP7 — PORTD bit 7 / parallel slave port |
| پن 31 | VSS — Ground (second tap) |
| پن 32 | VDD — Positive supply (second tap) |
| پن 33 | RB0/INT — PORTB bit 0 / external interrupt |
| پن 34 | RB1 — PORTB bit 1 |
| پن 35 | RB2 — PORTB bit 2 |
| پن 36 | RB3/PGM — PORTB bit 3 / low-voltage programming |
| پن 37 | RB4 — PORTB bit 4 |
| پن 38 | RB5 — PORTB bit 5 |
| پن 39 | RB6/PGC — PORTB bit 6 / ICSP clock (ICD clock) |
| پن 40 | RB7/PGD — PORTB bit 7 / ICSP data (ICD data) |
| پن 41 | VSS — Ground (third tap) |
| پن 42 | VDD — Positive supply (third tap) |
| پن 43 | NC — Not connected (per datasheet) |
| پن 44 | NC — Not connected (per datasheet) |
عام استعمالات
PIC16LF877AT-I/PT کے لیے موزوں ہے 6 ایپلیکیشنs: Industrial Sensor Interface Module, Low-Power Battery-Powered Data Logger, Small Appliance Motor Control, Automotive Body Electronics (Non-Safety), Consumer Appliance User Interface Board, RS-232/RS-485 Sensor Network Bridge.
Industrial Sensor Interface Module
PIC16LF877AT-I/PT suits industrial sensor-interface modules where its 10-bit ADC, 8 analog channels, and 33 I/O handle multiple transducer inputs at once. The 2.0-5.5 V VDD range lets the same MCU run from a 24V->5V industrial bus or a 3.3V regulated rail. Designers map analog channels to thermistor or strain-gauge bridges, while the EUSART streams telemetry to a host PLC at 115,200 baud or higher. Its 14 KB Flash accommodates look-up tables for linearization and the 368 B RAM can buffer up to 16 sample frames.
تجویز کردہ
Low-Power Battery-Powered Data Logger
PIC16LF877AT-I/PT is a strong fit for battery-powered data loggers drawing from the nanoWatt sleep modes and 2.0 V minimum VDD. With the ADC and EEPROM on-chip, the MCU can wake, capture, log, and return to deep sleep without external RTC glue. A two-AA alkaline pack delivers ~3.0 V that is right in the supply sweet spot, and the EUSART can dump logs via UART at full 20 MHz speed. The 14 KB Flash stores the state machine and compression routines, while 256 B EEPROM tolerates >1M write cycles for non-volatile event logs.
تجویز کردہ
Small Appliance Motor Control
PIC16LF877AT-I/PT can drive brushed DC or unipolar stepper motor control loops with the CCP module for PWM generation and the 16-bit timer for commutation timing. The 20 MHz core executes a 4 kHz PWM ISR with overhead to spare for current sensing via the 10-bit ADC and overcurrent shutdown via the analog comparator. Industrial-grade temperature range (-40 to +85 C) covers appliance cabinets. The 44-TQFP package fits behind the keypad PCB and the 33 I/O drive multiplexed 7-segment, button matrix, and triac control lines.
تجویز کردہ
Automotive Body Electronics (Non-Safety)
PIC16LF877AT-I/PT fits non-safety automotive body-electronics roles (interior lighting controllers, climate panel modules, seat-position memories) where 44-TQFP and 33 I/O expose enough signals for keypad, LCD, and LIN-style serial links. Industrial temperature grade covers cabin thermal envelopes; the wide supply range tolerates load-dump after-filter rails down to ~4 V. Designers implement UART-based K-line/LIN firmware in 14 KB Flash and use the analog comparator for overcurrent protection of seat motors or window switches.
تجویز کردہ
Consumer Appliance User Interface Board
PIC16LF877AT-I/PT hosts the user-interface board in consumer appliances like coffee machines, washing machines, and microwave ovens. Its 33 I/O drive multiplexed 7-segment displays, button matrices, rotary encoders, and buzzer PWM via the CCP module. The MSSP supports both SPI (for dot-matrix LCD) and I2C (for keypad or temperature sensors) on the same bus pins via Peripheral Pin Select alternatives. With RTC-free operation, the MCU keeps BOM lean while retaining ICSP for in-field firmware updates over a service connector.
تجویز کردہ
RS-232/RS-485 Sensor Network Bridge
PIC16LF877AT-I/PT serves as the bridge MCU for protocol conversion between UART-based sensors and RS-485 multi-drop industrial networks. The EUSART provides the asynchronous serial channel, while the MSSP drives SPI sensors and I2C accessories from a single bus. Its 14 KB Flash implements Modbus RTU command parsers and CRC checks, freeing up the host PLC. The 44-TQFP footprint exposes the dedicated MCLR and ICSP pins for service-port configuration without affecting firmware-loading on the host.
تجویز کردہ
تجویز کردہ پروڈکٹس کا خلاصہ
کے لیے انجینئرنگ ریفرنس ڈیٹا PIC16LF877AT-I/PT — موازنہ، ڈیزائن رہنمائی، اور تعمیل کی معلومات۔
انتخاب کی گائیڈ
متبادلات کے ساتھ موازنہ
| پیرامیٹر | یہ پروڈکٹ | PIC16LF877A-I/PT | PIC16F877AT-I/PT | PIC16LF877-04I/PT |
|---|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | TQFP-44 (10x10 mm) | TQFP-44 - same | TQFP-44 - same | TQFP-44 - same |
| Core / Frequency | PIC16 8-bit, 20 MHz | PIC16 8-bit, 20 MHz | PIC16 8-bit, 20 MHz | PIC16 8-bit, 4 MHz |
| Program Memory (Flash) | 14 KB | 14 KB | 14 KB | 14 KB |
| Data RAM | 368 B | 368 B | 368 B | 368 B |
| EEPROM | 256 B | 256 B | 256 B | 256 B |
| VDD Range | 2.0 V to 5.5 V | 2.0 V to 5.5 V | 4.0 V to 5.5 V | 2.0 V to 5.5 V |
| ADC | 10-bit, 8 channels | 10-bit, 8 channels | 10-bit, 8 channels | 10-bit, 8 channels |
اہم امتیازی خصوصیات
- Wide-voltage LF silicon (2.0-5.5 V) for battery operation (بمقابلہPIC16F877AT-I/PT)
- Full 20 MHz performance at all supply voltages (بمقابلہPIC16LF877-04I/PT)
- 44-TQFP package with exposed thermal footprint (بمقابلہPIC16LF877A-I/P (PDIP-40))
ڈیزائن نوٹس
Add a 100 nF ceramic decoupling capacitor within 5 mm of every VDD/VSS pair (pin 12/11, 32/31, 42/41). Place a bulk 10 uF aluminum-polymer cap at the board supply rail. The LF variant draws roughly 4 mA active at 20 MHz and <1 uA in deep sleep, so power-rail impedance matters mainly during fast ADC bursts.
Route the MCLR/RA5 pin (pin 1) with a 10 kohm pull-up to VDD and a 100 nF cap to ground for hardware reset; omit the cap if using internal MCLR only. Keep the ICSP/PGD (pin 40) and ICSP/PGC (pin 39) traces short (<50 mm) and away from switching nodes to avoid debugger noise. Use a 4-layer PCB if 20 MHz peripherals are present, otherwise 2-layer with a ground pour suffices.
Do not program the configuration bits to use the internal RC oscillator without checking the application timing margins, as the calibrated accuracy is +/-2%. Analog channels A0-A7 multiplex with PORTA/PORTE pins - leave VREF+/VREF- disconnected when using internal 5 V references to avoid conflict. The CCP1 pin (RC2) is not 5V-tolerant when the device is powered at 2.0 V; clamp signals with a series resistor.
تعمیل کی معلومات
RoHS-compliant per Microchip product page 39582C datasheet. Industrial grade (-40C to +85C), not AEC-Q100 qualified; not recommended for automotive safety functions.