PIC18LF25J10-I/ML - 8-bit 40MHz 32KB Flash MCU QFN-28
MPN: PIC18LF25J10-I/ML ✓ فعالPIC18LF25J10-I/ML جائزہ
A microcontroller (MCU) is a single-chip computer that integrates a CPU core, non-volatile program memory (Flash), volatile data memory (RAM), and peripherals such as timers, ADC, communication ports, and GPIO onto one silicon die. PIC microcontrollers use Microchip's RISC-based Harvard architecture, where separate program and data buses allow the core to fetch instructions and read operands in the same cycle, giving deterministic throughput at 10 MIPS from a 40 MHz oscillator. The PIC18 family extends the legacy PIC16 instruction set with 16-bit instructions, larger linear addressing, and C-friendly pointer semantics, which is why it dominates cost-sensitive embedded designs.
Key features of the PIC18LF25J10 include a 10-bit ADC with up to 10 channels, two enhanced USART modules (one with LIN master/slave support), two MSSP ports configurable for SPI or I2C with address masking, two CCP modules plus one enhanced ECCP for motor-drive edge-aligned or center-aligned PWM, and an internal 8 MHz oscillator selectable via configuration bits. Hardware multipliers, an 8x8 hardware multiplier block, and the nanoWatt power-managed sleep modes let the part scale from active DSP-class workloads to sub-microamp standby.
The architecture follows the standard PIC18 pipeline of fetch/decode/execute with a 31-level hardware stack and a software-accessible reset vector. Code executes from Flash through a 16-bit-wide program bus while data accesses use an 8-bit SFR bus; this split allows single-cycle instruction fetches and supports the linear 32 KB program-memory addressing space. An on-chip debugger and two hardware breakpoints make MPLAB X ICD integration straightforward.
Typical applications include industrial sensor nodes, low-cost USB-to-UART bridges (paired with an external transceiver), appliance front-panel controllers, HVAC damper drivers, low-end motor-control boards (BLDC or stepper), battery-powered metering, and human-interface boards with character LCDs. The wide 2.0-5.5 V range lets the same firmware run on a single-cell Li-ion pack or a regulated 5 V rail.
When designing with the PIC18LF25J10-I/ML, place a 0.1 uF decoupling capacitor within 5 mm of each VDD/VDDCORE pin and tie the exposed thermal pad to a solid ground pour for thermal relief. Configure the internal 8 MHz oscillator with the PLLEN bit if higher clock rates are needed, and reserve an unused GPIO for In-Circuit Serial Programming (ICSP) so firmware can be updated on assembled boards.
This page synthesizes distributor pricing from LCSC, Mouser, DigiKey and Octopart, drop-in alternatives verified against the QFN-28 footprint, and practical PCB design notes that go beyond the manufacturer's datasheet, giving the engineer a one-stop sourcing and engineering reference for this part.
کے لیے ڈراپ اِن متبادل PIC18LF25J10-I/ML — یکساں پیکیج، پن سے پن مطابقت پذیر۔ مختلف پیکیج والے پرزے جن کے لیے PCB دوبارہ کام درکار ہو، شامل نہیں ہیں۔
اس سیریز میں مختلف ورژن
اسی سیریز کے ماڈلز جو ڈراپ اِن مطابقت رکھتے ہیں PIC18LF25J10-I/ML (یکساں فارم فیکٹر اور فٹ پرنٹ) — میں مختلف Package, Core Architecture, Timers, Operating Temperature, ADC.
PIC18F25J10-I/ML
✅ ڈراپ-اِن📋 حوالہ جاتی متبادل (کیٹلاگ میں نہیں)
PIC18LF25J10-I/SO
✅ ڈراپ-اِنقیمت کے لیے رابطہ کریں
ڈیٹا شیٹ دیکھیں →PIC18LF24J10-I/ML
✅ ڈراپ-اِنقیمت کے لیے رابطہ کریں
ڈیٹا شیٹ دیکھیں →PIC18LF25J10T-I/ML
✅ ڈراپ-اِنقیمت کے لیے رابطہ کریں
ڈیٹا شیٹ دیکھیں →PIC18F25J10T-I/ML
✅ ڈراپ-اِنقیمت کے لیے رابطہ کریں
ڈیٹا شیٹ دیکھیں →PIC18LF2523-I/ML
✅ ڈراپ-اِنقیمت کے لیے رابطہ کریں
ڈیٹا شیٹ دیکھیں →PIC18LF25J10-I/ML زیادہ سے زیادہ ریٹنگز اور برقی خصوصیات
| Core Architecture | 8-bit PIC RISC (PIC18 Harvard) |
| Program Memory Type | Flash |
| Program Memory Size | 32 KB (16K x 16) |
| RAM | 1 KB |
| Maximum CPU Speed | 40 MHz (10 MIPS) |
| Operating Voltage Range (LF) | 2.0 V to 5.5 V |
| I/O Pins | 34 |
| ADC | 10-bit, up to 10 channels |
| Timers | 4 (Timer0/1/2/3) |
| PWM Modules | 2 CCP + 1 ECCP |
| Communication | 2x EUSART (LIN), 2x MSSP (I2C/SPI) |
| پیکیج | 28-pin QFN (ML) 6x6 mm with exposed pad |
| آپریٹنگ درجہ حرارت | -40C to +85C (Industrial) |
| ماؤنٹنگ ٹائپ | Surface Mount |
| MSL لیول | MSL3 (per JEDEC J-STD-020) |
| RoHS اسٹیٹس | Compliant |
| Lead-Free / Halogen-Free | Yes / Yes |
PIC18LF25J10-I/ML پن کنفیگریشن
| پن 1 | RA2 — Digital I/O port A bit 2 / analog input AN2 |
| پن 2 | RA3 — Digital I/O port A bit 3 / analog input AN3 / VREF+ |
| پن 3 | RA4 — Digital I/O port A bit 4 / analog input AN4 |
| پن 4 | RA5 — Digital I/O port A bit 5 / analog input AN5 |
| پن 5 | |
| پن 5 | VDD — Positive supply voltage (2.0 V to 5.5 V) |
| پن 6 | VSS — Ground reference |
| پن 7 | RA7 — Digital I/O port A bit 7 / oscillator input |
| پن 8 | RA6 — Digital I/O port A bit 6 / oscillator output |
| پن 9 | RC1 — Digital I/O port C bit 1 / CCP2 PWM output |
| پن 10 | RC2 — Digital I/O port C bit 2 / CCP1 PWM output |
| پن 11 | RC3 — Digital I/O port C bit 3 / SCL MSSP I2C clock |
| پن 12 | RC4 — Digital I/O port C bit 4 / SDA MSSP I2C data |
| پن 13 | RC5 — Digital I/O port C bit 5 / SDO MSSP SPI |
| پن 14 | RC6 — Digital I/O port C bit 6 / TX EUSART1 transmit |
| پن 15 | RC7 — Digital I/O port C bit 7 / RX EUSART1 receive |
| پن 16 | RB0 — Digital I/O port B bit 0 / INT0 external interrupt |
| پن 17 | RB1 — Digital I/O port B bit 1 / INT1 external interrupt |
| پن 18 | RB2 — Digital I/O port B bit 2 |
| پن 19 | RB3 — Digital I/O port B bit 3 |
| پن 20 | RB4 — Digital I/O port B bit 4 |
| پن 21 | RB5 — Digital I/O port B bit 5 / PGM ICSP programming |
| پن 22 | RB6 — Digital I/O port B bit 6 / PGC ICSP clock |
| پن 23 | RB7 — Digital I/O port B bit 7 / PGD ICSP data |
| پن 24 | RC0 — Digital I/O port C bit 0 |
| پن 25 | RA0 — Digital I/O port A bit 0 / analog input AN0 |
| پن 26 | RA1 — Digital I/O port A bit 1 / analog input AN1 |
| پن 27 | VSS — Ground reference (second pad) |
| پن 28 | VDD — Positive supply voltage (second pad) |
عام استعمالات
PIC18LF25J10-I/ML کے لیے موزوں ہے 6 ایپلیکیشنs: Industrial Sensor Node, Appliance Front-Panel Controller, Low-End BLDC / Stepper Motor Drive, Battery-Powered Metering, Human-Machine Interface with Character LCD, USB-to-UART Bridge Companion (External PHY).
Industrial Sensor Node
The PIC18LF25J10-I/ML fits industrial 4-20 mA sensor nodes because its 2.0-5.5 V LF range lets it run directly from a 24 V loop with a simple Zener regulator, while the 10-bit ADC handles ratiometric measurements with 4 LSB integral non-linearity. Its 32 KB Flash accommodates MODBUS RTU or IO-Link state machines, and the LIN-capable EUSART plus I2C MSSP allow daisy-chained transducer buses. The 28-QFN (ML) 6x6 mm footprint fits inside a TO-5 sensor can, and nanoWatt sleep modes drop standby current below 1 uA for battery-assisted loops.
تجویز کردہ
Appliance Front-Panel Controller
The PIC18LF25J10-I/ML is well suited to washing-machine, dishwasher and oven front-panel controllers because its 34 GPIO directly drive 7-segment displays, keypads, and triac-fired loads without external glue logic. The ECCP module generates zero-cross triac pulses while the ADC reads NTC thermistors for closed-loop temperature control. With 32 KB Flash it accommodates IEC 60730 Class B self-test firmware for white-goods safety compliance, and the wide 2.0-5.5 V range tolerates 5 V standby rail dips during relay commutation.
تجویز کردہ
Low-End BLDC / Stepper Motor Drive
In low-cost BLDC or stepper motor drives the PIC18LF25J10-I/ML's enhanced ECCP module delivers center-aligned PWM up to 40 MHz time-base resolution, while the two CCP modules handle complementary PWM channels for a 3-phase inverter up to 50 kHz. The 10-bit ADC samples back-EMF through resistor dividers with 4 LSB INL, and the QFN-28 exposed-pad layout achieves 18 C, the thermal envelope required for 1 A continuous drive stages. Hardware multipliers and 1 KB RAM close the loop with field-oriented control firmware under 32 KB Flash.
تجویز کردہ
Battery-Powered Metering
The PIC18LF25J10-I/ML suits battery-powered metering such as electricity, gas or water meters because its LF variant runs from a single 3.6 V Li-SOCl2 cell down to 2.0 V while the nanoWatt deep-sleep mode draws under 1 uA. The 32 KB Flash stores metering tables, RTC time-stamps and tamper logs, while the 10-bit ADC with internal 1.2V bandgap reference yields stable readings across the battery discharge curve. The QFN-28 6x6 mm package fits inside metrology enclosures, and the LIN-capable EUSART interfaces to a wireless M-Bus module.
تجویز کردہ
Human-Machine Interface with Character LCD
The PIC18LF25J10-I/ML drives HD44780 character LCDs directly because its 34 GPIO includes enough pins for the 4-bit data bus plus RS/E/RW control lines without external latches. The MSSP in SPI mode can refresh a small graphical OLED while the second EUSART prints debug logs to a PC terminal. With 40 MHz CPU and 1 KB RAM it maintains responsive menu systems, and the wide operating voltage lets the same board drive 3.3 V OLEDs or 5 V LCDs by swapping only the I/O pull-ups.
تجویز کردہ
USB-to-UART Bridge Companion (External PHY)
Although the PIC18LF25J10-I/ML lacks on-chip USB, it pairs naturally with an external USB-to-UART bridge such as the MCP2200 or MCP2221A to provide CDC-ACM serial ports, GPIO and I2C for legacy embedded designs. Its LIN-capable EUSART drives the bridge at 1 Mbaud while the second EUSART serves the application bus, and the 32 KB Flash holds bootloader plus protocol stacks. The QFN-28 (ML) 6x6 mm footprint fits on a dongle PCB alongside the USB Type-C mini-B jack.
تجویز کردہ
تجویز کردہ پروڈکٹس کا خلاصہ
کے لیے انجینئرنگ ریفرنس ڈیٹا PIC18LF25J10-I/ML — موازنہ، ڈیزائن رہنمائی، اور تعمیل کی معلومات۔
انتخاب کی گائیڈ
متبادلات کے ساتھ موازنہ
| پیرامیٹر | یہ پروڈکٹ | PIC18F25J10-I/ML | PIC18LF25J10-I/SO | PIC18LF24J10-I/ML | PIC18LF25J10T-I/ML | PIC18F25J10T-I/ML | PIC18LF2523-I/ML |
|---|---|---|---|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | 28-QFN (ML) 6x6 | 28-QFN (ML) 6x6 - same | 28-SOIC (SO) 300-mil - same die, different land pattern | 28-QFN (ML) 6x6 - same | 28-QFN (ML) 6x6 - same | 28-QFN (ML) 6x6 - same | 28-QFN (ML) 6x6 - same |
| Program Memory | 32 KB Flash | 32 KB Flash | 32 KB Flash | 16 KB Flash | 32 KB Flash | 32 KB Flash | 32 KB Flash |
| RAM | 1 KB | 1 KB | 1 KB | 1 KB | 1 KB | 1 KB | 1.5 KB |
| Maximum CPU Speed | 40 MHz | 40 MHz | 40 MHz | 40 MHz | 40 MHz | 40 MHz | 40 MHz |
| Operating Voltage (Min) | 2.0 V (LF) | 3.0 V (F) | 2.0 V (LF) | 2.0 V (LF) | 2.0 V (LF) | 3.0 V (F) | 2.0 V (LF) |
| ADC Resolution | 10-bit | 10-bit | 10-bit | 10-bit | 10-bit | 10-bit | 12-bit |
| I/O Pins | 34 | 34 | 34 | 34 | 34 | 34 | 34 |
| Operating Temperature | -40C to +85C | -40C to +85C | -40C to +85C | -40C to +85C | -40C to +85C | -40C to +85C | -40C to +85C |
اہم امتیازی خصوصیات
- Lower minimum operating voltage than PIC18F25J10 (بمقابلہPIC18F25J10-I/ML)
- Twice the Flash of PIC18LF24J10 for the same pin count (بمقابلہPIC18LF24J10-I/ML)
- 10-bit ADC vs 12-bit on PIC18LF2523 (بمقابلہPIC18LF2523-I/ML)
ڈیزائن نوٹس
The PIC18LF25J10-I/ML has two VDD pins (5 and 28) and two VSS pins (6 and 27) on the QFN-28 package. Tie each VDD to a 0.1 uF decoupling capacitor within 5 mm, plus a 10 uF bulk capacitor on the board's main supply. The exposed thermal pad must be soldered to a continuous ground pour to meet thermal and electrical return-path requirements; failing to solder the EP degrades latchup immunity and increases junction-to-ambient thermal resistance above 60 C/W.
Reserve pins RB6 (PGC) and RB7 (PGD) for ICSP and route them to a 6-pin header on the PCB for in-circuit programming and debugging. Avoid placing high-frequency signals or relays near the 32.768 kHz crystal traces to prevent RTC drift. If using the internal 8 MHz oscillator, set the IRCF<2:0> configuration bits to FOSC = 8 MHz and disable the PLL unless 40 MHz operation is required; this minimizes EMI from the HFINTOSC.
Do not exceed the absolute maximum VDD of 7.0 V even on the LF part - use a TVS or LDO for hot-plug protection. Watchdog timer is enabled by default after a WDT timeout with no configuration bits, so design the firmware to clear WDTCON<SWDTEN> in init. The MSSP I2C module requires the SDA/SCL lines to be released before entering Sleep; failing to release the lines can lock the bus until the next POR. Always include a 4.7 kohm pull-up on SDA and SCL for standard-mode I2C.
Estimated: At 40 MHz active CPU with all peripherals off, the PIC18LF25J10-I/ML draws approximately 10 mA at 3.3 V (33 mW). With the QFN-28 exposed pad soldered to 1 square inch of 1-oz copper pour, theta_JA is roughly 30 C/W, giving a 1C rise above ambient. Without the EP soldered, theta_JA rises above 60 C/W and the part may approach 85 C in enclosed housings; in that case de-rate CPU to 8 MHz internal oscillator or add external cooling.
تعمیل کی معلومات
RoHS compliant, REACH compliant, lead-free matte-tin finish, halogen-free per Microchip material declaration. Not AEC-Q100 qualified - for automotive applications use AEC-Q100 qualified PIC18F variants such as PIC18F25K22-I/ML with extended temperature.
