Texas Instruments

SN75150D - Dual RS-232 Line Driver | Texas Instruments

MPN: SN75150D ✗ اختتامِ زندگی
12 V and -12 V Vdss 8-pin SOIC Package
MOQ: 1 |

SN75150D جائزہ

The Texas Instruments SN75150D is a monolithic dual RS-232 line driver designed for data-terminal equipment and data-communication equipment interfaces defined by TIA/EIA-232-F. It provides two transmit channels in an 8-pin SOIC package and supports transmission at 20 kbit/s with a full 2500-pF load. The device uses positive and negative supply rails, and its TTL-compatible logic inputs make it suitable for interfacing with many standard logic families.

A line driver is an interface IC that converts digital logic-level signals into differential or bipolar signaling suitable for transmission over a communication cable. The SN75150 belongs to the broader RS-232 interface family, alongside line receivers and combined transceiver devices. It is intended for point-to-point data transmission, level translation, and driving MOS-device inputs where a stronger, polarity-aware output signal is useful.

The principal features of the SN75150D include two independent driver outputs, support for the TIA/EIA-232-F interface requirements, a stated transmission rate of 20 kbit/s with a full 2500-pF load, and operation from 12-V and -12-V supplies. The logic input is compatible with most TTL families. The manufacturer product page also identifies data-transmission systems using relatively short single lines, level translators, and MOS-device drivers as additional applications.

The SN75150D is a transmit-only device. It does not include an RS-232 receiver, so a complete bidirectional RS-232 link requires a separate receiver IC or transceiver. This distinction matters when allocating connectors and signal paths: each transmit signal is driven by the SN75150D, while incoming signals must be routed to a suitable receiver. The SOIC-8 package also makes the device appropriate for conventional surface-mount PCB assembly rather than through-hole insertion.

Typical deployments include serial console links, industrial equipment interfaces, short-distance data-transfer systems, and level-conversion circuits between TTL logic and bipolar RS-232 equipment. Because the driver is designed for relatively short single lines, cable length, load capacitance, grounding, and signal integrity should be checked against the interface requirements rather than treated as unlimited-distance links.

When laying out the circuit, place the SN75150D close to the connector or protected interface boundary and route the RS-232 outputs away from sensitive analog and clock signals. Confirm both positive and negative supply rails are present, and ensure downstream receivers are not driven beyond their permitted input limits. The absence of an integrated receiver means system-level communication requires coordinated driver and receiver selection.

This product page organizes the manufacturer specifications, interface role, sourcing information, application guidance, and design considerations into a practical engineering reference for the SN75150D.

کے لیے ڈراپ اِن متبادل SN75150D — یکساں پیکیج، پن سے پن مطابقت پذیر۔ مختلف پیکیج والے پرزے جن کے لیے PCB دوبارہ کام درکار ہو، شامل نہیں ہیں۔

SN75150DG4

✅ ڈراپ-اِن
📦 8-SOIC
Same SN75150-family dual-driver configuration and 8-SOIC package; exact ordering suffix and temperature-grade details require confirmation

📋 حوالہ جاتی متبادل (کیٹلاگ میں نہیں)

SN75150D تفصیلات

Device Type Dual RS-232 line driver
Number of Drivers 2
Interface Standard TIA/EIA-232-F
Maximum Data Rate 20 kbit/s with a full 2500-pF load
Load Capacitance 2500 pF
سپلائی وولٹیج 12 V and -12 V
آپریٹنگ درجہ حرارت رینج 0 C to 70 C
Logic Compatibility Compatible with most TTL families
پیکیج 8-pin SOIC
ماؤنٹنگ ٹائپ Surface mount
Output Transition Time 2 us maximum through the -3-V transition region
Output Short Circuit Tolerance Sustained short circuit to low-impedance voltages between -25 V and 25 V

SN75150D 8-pin soic پن کنفیگریشن گائیڈ

SN75150D (8-pin soic پیکیج) کے لیے پن کنفیگریشن۔ پن نمبرنگ، فنکشنز اور کنکشن ڈایاگرامز مینوفیکچرر کے ڈیٹا شیٹ میں بیان کیے گئے ہیں۔ درست فٹ پرنٹ اور سولڈرنگ رہنما ہدایات کے لیے اسی سے رجوع کریں۔

SN75150D کے لیے 8-pin soic پیکیج پن آؤٹ ڈایاگرام

کے لیے تفصیلی پن آؤٹ ڈیٹا دستیاب نہیں SN75150D.

رجوع کریں ڈیٹا شیٹ مکمل پن کنفیگریشن کے لیے۔

عام استعمالات

SN75150D کے لیے موزوں ہے 6 ایپلیکیشنs: Industrial RS-232 Data Links, Serial Console and Control Interface, TTL-to-RS-232 Level Translation, Short-Distance Equipment-to-Equipment Communication, MOS-Device Interface Driving, Legacy Serial Port Expansion.

🏭

Industrial RS-232 Data Links

The SN75150D is suitable for industrial short-range serial links because its two driver channels implement the bipolar RS-232 transmit side specified by TIA/EIA-232-F. Each channel can operate at up to 20 kbit/s when presented with the full 2500-pF load. Place the IC near the protected connector or interface boundary, provide 12-V and -12-V rails, and route the outputs as a twisted pair to the corresponding receiver. The design should account for cable capacitance, grounding, surge protection, and receiver thresholds. Because the SN75150D has two drivers and no receivers, it suits equipment that transmits on one or two lines and uses a separate receiver IC for returning data.

🖥️

Serial Console and Control Interface

The SN75150D can provide the transmit stage for a serial console or embedded control port. Its logic inputs are compatible with most TTL families, allowing a microcontroller or UART to control the driver without an intermediate logic translator. The two available driver channels can carry independent transmit signals, while incoming data requires a separate RS-232 receiver. A practical implementation places the driver close to the connector, uses local 12-V and -12-V regulation, and keeps the two RS-232 conductors away from clocks, ADC inputs, and other sensitive analog nodes. Validate timing at the intended bit rate against the total cable and protection-network capacitance.

🔧

TTL-to-RS-232 Level Translation

The SN75150D fits a TTL-to-RS-232 transmit converter because its logic inputs are compatible with most TTL families and its outputs provide the bipolar signaling required for RS-232 equipment. The source logic drives the two input channels, while the outputs connect to the appropriate RS-232 conductors. This configuration is useful when legacy peripherals use bipolar serial signaling but the controller operates at TTL levels. The circuit requires positive and negative supply rails, suitable local bypassing, and careful treatment of signal ground. Check the receiver's input thresholds, cable length, and capacitive loading before finalizing the interface because the published 20 kbit/s rate is specified with a full 2500-pF load.

🌐

Short-Distance Equipment-to-Equipment Communication

The SN75150D supports short-distance equipment-to-equipment communication links based on relatively short single lines. Its TIA/EIA-232-F orientation and 20 kbit/s rate make it appropriate for legacy serial ports, service interfaces, and control connections between cabinets or instruments. The transmit-only architecture allows a compact board to add two outbound channels without duplicating receiver circuitry. For reliable operation, calculate the aggregate load presented by cable capacitance, connector capacitance, protection components, and the receiving device. Keep the signal and return paths appropriately paired and terminate the interface according to the receiving equipment's expectations.

🔧

MOS-Device Interface Driving

The Texas Instruments SN75150 product page identifies driving MOS devices as an additional use for the SN75150 family. The bipolar RS-232 outputs can deliver a stronger, polarity-aware signal than a bare logic output, which is useful when the connected device requires a defined positive or negative input level. The implementation must account for the MOS input's voltage limits, the driver's output levels, supply sequencing, and any input clamp behavior. Do not treat the line-driver output as a general-purpose power output. Confirm that the load is within the published drive capability and that sustained shorts or abnormal cable conditions remain compatible with the device's protection characteristics.

🔧

Legacy Serial Port Expansion

Two SN75150D drivers can expand a design's available RS-232 transmit channels when one interface controller does not provide enough outputs. Each driver converts a compatible logic signal into a separate bipolar output, enabling status, command, or data signals to reach legacy equipment. The added channels still share the same supply and return constraints as other RS-232 transmitters. Place the IC close to the connector or protection devices, provide local supply bypassing, and avoid long stubs from the driver to the connector. Confirm that the receiving devices accept the generated levels and that the aggregate wiring capacitance does not degrade the intended 20 kbit/s data rate.

What is the SN75150D and what does it do?
The SN75150D is a Texas Instruments monolithic dual RS-232 line driver with two transmit outputs and no integrated receiver. According to the Texas Instruments SN75150 product page, it is designed for the interface between data-terminal equipment and data-communication equipment defined by TIA/EIA-232-F. It converts suitable logic-level inputs into bipolar RS-232 driver signals for short-distance data transmission, level translation, and MOS-device drive applications.
What is the maximum data rate of SN75150D?
The SN75150D supports a maximum transmission rate of 20 kbit/s when driving a full 2500-pF load. This figure is stated on the Texas Instruments SN75150 product page. The load condition is important because longer cables, protection networks, connectors, and receiver capacitance increase the total capacitive load presented to each driver. Designers should verify the complete channel load and timing margin before treating the 20 kbit/s figure as a system guarantee.
Does SN75150D contain an RS-232 receiver?
No, the SN75150D contains two line drivers and zero receivers, so it is a transmit-only RS-232 device. The Texas Instruments product page identifies the part as a dual line driver, while the distributor description identifies it as a 2/0 driver. A bidirectional RS-232 connection therefore requires a separate receiver or a suitable transceiver elsewhere in the interface circuit.
What supply voltages does SN75150D require?
The SN75150D operates from 12-V and -12-V power supplies, as stated on the Texas Instruments SN75150 product page. RS-232 line drivers commonly use positive and negative rails so that output transitions can reach both positive and negative signal levels. The circuit must provide both rails with suitable decoupling, and the selected power source must maintain the required levels over the operating temperature range.
What is the SN75150D operating temperature range?
The SN75150D is characterized for operation from 0 C to 70 C. This operating range is reported on the Texas Instruments SN75150 product page. It is suitable for commercial-temperature equipment when the surrounding enclosure and system requirements stay within that range. Industrial or extended-temperature designs should use a device specifically characterized for the required temperature range rather than extrapolating beyond the published limits.
Which package does SN75150D use?
The SN75150D is offered in an 8-pin SOIC package for surface-mount PCB assembly. The Texas Instruments part-details page identifies the SN75150D ordering option, and the distributor product description identifies it as an 8-SOIC RS-232 driver. The eight pins provide two driver channels, power connections, and ground connections according to the device pin description.
Where can I download the SN75150D datasheet?
The official SN75150D technical information is available from the Texas Instruments product page at https://www.ti.com/product/SN75150, which links to the manufacturer documentation for the SN75150 family. The SN75150D datasheet is also hosted by the Texas Instruments part-details page at https://www.ti.com/product/SN75150/part-details/SN75150D. Use the manufacturer copy for final pin assignments, electrical limits, and operating conditions.
Where can I find the SN75150D pinout?
The SN75150D pinout is identified in the manufacturer pin-description information for the SN75150 family and in the official datasheet linked from the Texas Instruments product page. The device uses an 8-pin SOIC outline, so the published pin table should be cross-checked against the PCB footprint before layout. Use the manufacturer pin table for exact signal names and power-pin assignments.
Can SN75150D drive a long RS-232 cable?
The SN75150D is intended primarily for relatively short single-line data-transmission systems rather than unlimited-distance RS-232 links, according to the Texas Instruments product page. Its stated 20 kbit/s capability is tied to a 2500-pF load, and cable capacitance grows with length. For a long or heavily loaded cable, validate the complete capacitance, driver slew rate, receiver thresholds, protection circuitry, and signal timing before selecting the part.
What is the best drop-in replacement for SN75150D?
The best drop-in replacement is the device that has the same 8-pin SOIC footprint, identical pin functions, equivalent supply requirements, and comparable RS-232 output performance. No confirmed alternate MPN is identified on this product page, so a replacement should not be selected from a generic cross-reference result alone. Request a quote for SN75150D, or ask the manufacturer cross-reference service to identify a qualified source for the exact package and pin configuration.
Is SN75150D suitable for TTL to RS-232 conversion?
Yes, the SN75150D is suitable for TTL-to-RS-232 transmit conversion because the Texas Instruments product page states that its logic input is compatible with most TTL families. Place the TTL-side device and the SN75150D together in the transmitter path, then connect the two bipolar outputs to the appropriate RS-232 lines. The circuit must also provide 12-V and -12-V rails and account for connector protection and signal-ground requirements.
SN75150D versus MC1489-series drivers - which should be selected?
The SN75150D is a two-driver-only device intended for TIA/EIA-232-F transmit operation, while an MC1489-family part belongs to a different driver and receiver product family. Because the cross-reference information does not establish identical pin assignments, supply levels, output ratings, or channel counts for a specific MC1489 variant, it cannot be treated as a verified drop-in replacement here. Select the part whose manufacturer pin table and electrical limits match the existing PCB exactly.
What can replace SN75150D in an existing PCB design?
A valid SN75150D replacement must preserve the 8-pin SOIC pinout, dual-driver channel arrangement, TTL-compatible inputs, positive and negative supply operation, and RS-232 output behavior. No manufacturer-confirmed or web-cataloged drop-in substitute is identified for this exact MPN, so a broad functional equivalence is not enough to authorize a PCB swap. Review the official SN75150D datasheet and obtain a manufacturer cross-reference before changing the BOM.
Where can I buy SN75150D and check its price?
Use the Request a Quote form on this page to ask about SN75150D price, current availability, minimum order quantity, and lead time. The manufacturer product page and distributor records identify the part as a Texas Instruments 2/0 RS-232 driver in an 8-pin SOIC package, but no explicit quantity-break price is included for structured comparison. The quote form keeps commercial details tied to the current request.
What are the key specifications of SN75150D that engineers should know?
The key SN75150D specifications are two RS-232 driver channels, no integrated receiver, 20 kbit/s operation with a full 2500-pF load, 12-V and -12-V operation, and a 0 C to 70 C commercial-temperature range. The device also uses an 8-pin SOIC package and accepts logic inputs compatible with most TTL families. According to the Texas Instruments SN75150 product page, it meets or exceeds the requirements of TIA/EIA-232-F.

کے لیے انجینئرنگ ریفرنس ڈیٹا SN75150D — موازنہ، ڈیزائن رہنمائی، اور تعمیل کی معلومات۔

انتخاب کی گائیڈ

Choose the SN75150D for a two-channel RS-232 transmit stage when the PCB uses an 8-pin SOIC footprint and the design can provide 12-V and -12-V supplies. It is particularly appropriate for short-distance links, TTL-to-RS-232 transmit conversion, and applications operating from 0 C to 70 C. The component is intentionally transmit-only, so a complete bidirectional port also needs a separate receiver or transceiver. No confirmed drop-in substitute is identified for this exact MPN. When replacing it, require the same SOIC-8 pin assignments, two driver channels, compatible logic inputs, equivalent bipolar output behavior, and compatible supply requirements. Treat broader MC1488 or MC1489 family devices as candidates only after checking their exact channel count, pinout, supply voltages, and electrical ratings against the existing schematic. For legacy equipment, also verify the remote receiver thresholds, cable capacitance, and required data rate.

ڈیزائن نوٹس

Place the SN75150D close to the RS-232 connector or protection network. Keep each driver output on a controlled route with an appropriate return path, and separate these routes from clocks, ADC inputs, and sensitive analog signals. Provide local supply bypassing for both 12-V and -12-V rails and verify that connector and protection-component capacitance does not exceed the conditions associated with the published 20 kbit/s rate.

Do not assume that the SN75150D implements a complete RS-232 port. It contains two drivers and no receivers, so bidirectional communication requires another interface device. Also confirm that logic levels, supply polarity, and output voltage limits match the connected equipment. A pin-compatible footprint alone is insufficient for a replacement because enable, shutdown, fault, or receiver functions may differ between otherwise similar driver packages.

Evaluate the complete channel rather than only the driver output. Include cable capacitance, connector capacitance, protection devices, receiver input loading, and any stubs in the capacitive budget. The SN75150D is rated for 20 kbit/s with a full 2500-pF load, so a slower data rate or longer cable may be required when total loading is higher. Preserve the RS-232 signal-to-return relationship and use the manufacturer's electrical limits when checking output behavior.

تعمیل کی معلومات

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
لیڈ فری
Unknown
ہیلوجن فری
Unknown
کنفلیکٹ منرلز
Unknown

The available product information does not state RoHS, REACH, lead-free, halogen-free, or conflict-minerals status. The SN75150 is not identified as an automotive-qualified AEC-Q100 device.

ڈیٹا کی تصدیق کی تاریخ: 2026-11-09 — ڈیٹا XAIPART کی کمپوننٹ انجینئرنگ ٹیم کے ذریعے تصدیق شدہ اور ترتیب شدہ

متعلقہ تلاشیں

SN75150D datasheet SN75150D pinout SN75150D datasheet pdf SN75150D equivalent SN75150D replacement SN75150D drop-in replacement SN75150D 8-SOIC pinout SN75150D RS-232 driver SN75150D 20 kbit/s SN75150D price SN75150D stock Texas Instruments SN75150D SN75150D application circuit SN75150D vs MC1489

متعلقہ اجزاء اور اصطلاحات

Texas Instruments SN75150D SN75150 RS-232 TIA/EIA-232-F dual line driver interface IC line driver TTL MOS level translator 20 kbit/s 2500 pF 12 V -12 V 0 C to 70 C 8-pin SOIC SOIC family surface-mount package bipolar signaling short-distance data transmission RS-232 receiver data-terminal equipment data-communication equipment
فوری کوٹ RFQ
مکمل تفصیلات بھریں — ہماری سیلز ٹیم 24 گھنٹوں میں جواب دے گی
پارٹ نمبر مینوفیکچرر پیکج QTY ہدف قیمت کل رقم
✓
کوٹ جمع ہو گیا!

ہم 24 گھنٹوں کے اندر آپ کے ای میل کا جواب دیں گے

1
RFQ جمع ہو گیا
2
کوٹ موصول ہو گیا
3
آرڈر دے دیا گیا
4
ادائیگی
5
بھیج دیا گیا
6
ڈیلیور شدہ
RFQ تفصیلات دیکھیں