SN75150D - Dual RS-232 Line Driver | Texas Instruments
MPN: SN75150D ✗ 停產SN75150D 概覽
A line driver is an interface IC that converts digital logic-level signals into differential or bipolar signaling suitable for transmission over a communication cable. The SN75150 belongs to the broader RS-232 interface family, alongside line receivers and combined transceiver devices. It is intended for point-to-point data transmission, level translation, and driving MOS-device inputs where a stronger, polarity-aware output signal is useful.
The principal features of the SN75150D include two independent driver outputs, support for the TIA/EIA-232-F interface requirements, a stated transmission rate of 20 kbit/s with a full 2500-pF load, and operation from 12-V and -12-V supplies. The logic input is compatible with most TTL families. The manufacturer product page also identifies data-transmission systems using relatively short single lines, level translators, and MOS-device drivers as additional applications.
The SN75150D is a transmit-only device. It does not include an RS-232 receiver, so a complete bidirectional RS-232 link requires a separate receiver IC or transceiver. This distinction matters when allocating connectors and signal paths: each transmit signal is driven by the SN75150D, while incoming signals must be routed to a suitable receiver. The SOIC-8 package also makes the device appropriate for conventional surface-mount PCB assembly rather than through-hole insertion.
Typical deployments include serial console links, industrial equipment interfaces, short-distance data-transfer systems, and level-conversion circuits between TTL logic and bipolar RS-232 equipment. Because the driver is designed for relatively short single lines, cable length, load capacitance, grounding, and signal integrity should be checked against the interface requirements rather than treated as unlimited-distance links.
When laying out the circuit, place the SN75150D close to the connector or protected interface boundary and route the RS-232 outputs away from sensitive analog and clock signals. Confirm both positive and negative supply rails are present, and ensure downstream receivers are not driven beyond their permitted input limits. The absence of an integrated receiver means system-level communication requires coordinated driver and receiver selection.
This product page organizes the manufacturer specifications, interface role, sourcing information, application guidance, and design considerations into a practical engineering reference for the SN75150D.
直接替換替代品,適用於 SN75150D — 相同封裝,腳位對腳位相容。需重新設計 PCB 的不同封裝零件不列入。
SN75150DG4
✅ 直接替換📋 參考替代品(不在目錄中)
SN75150D 規格
| Device Type | Dual RS-232 line driver |
| Number of Drivers | 2 |
| Interface Standard | TIA/EIA-232-F |
| Maximum Data Rate | 20 kbit/s with a full 2500-pF load |
| Load Capacitance | 2500 pF |
| 供應電壓 | 12 V and -12 V |
| 工作溫度範圍 | 0 C to 70 C |
| Logic Compatibility | Compatible with most TTL families |
| 封裝 | 8-pin SOIC |
| 安裝類型 | Surface mount |
| Output Transition Time | 2 us maximum through the -3-V transition region |
| Output Short Circuit Tolerance | Sustained short circuit to low-impedance voltages between -25 V and 25 V |
SN75150D 8-pin soic 腳位配置指南
SN75150D(8-pin soic 封裝)的腳位配置。 腳位編號、功能與連接圖定義於製造商資料手冊中。請參閱該手冊以取得確切的封裝尺寸與焊接指引。
無詳細腳位定義資料: SN75150D.
請參閱 資料表 以查看完整腳位配置。
典型應用
SN75150D 適用於 6 應用s: Industrial RS-232 Data Links, Serial Console and Control Interface, TTL-to-RS-232 Level Translation, Short-Distance Equipment-to-Equipment Communication, MOS-Device Interface Driving, Legacy Serial Port Expansion.
Industrial RS-232 Data Links
The SN75150D is suitable for industrial short-range serial links because its two driver channels implement the bipolar RS-232 transmit side specified by TIA/EIA-232-F. Each channel can operate at up to 20 kbit/s when presented with the full 2500-pF load. Place the IC near the protected connector or interface boundary, provide 12-V and -12-V rails, and route the outputs as a twisted pair to the corresponding receiver. The design should account for cable capacitance, grounding, surge protection, and receiver thresholds. Because the SN75150D has two drivers and no receivers, it suits equipment that transmits on one or two lines and uses a separate receiver IC for returning data.
推薦
Serial Console and Control Interface
The SN75150D can provide the transmit stage for a serial console or embedded control port. Its logic inputs are compatible with most TTL families, allowing a microcontroller or UART to control the driver without an intermediate logic translator. The two available driver channels can carry independent transmit signals, while incoming data requires a separate RS-232 receiver. A practical implementation places the driver close to the connector, uses local 12-V and -12-V regulation, and keeps the two RS-232 conductors away from clocks, ADC inputs, and other sensitive analog nodes. Validate timing at the intended bit rate against the total cable and protection-network capacitance.
推薦
TTL-to-RS-232 Level Translation
The SN75150D fits a TTL-to-RS-232 transmit converter because its logic inputs are compatible with most TTL families and its outputs provide the bipolar signaling required for RS-232 equipment. The source logic drives the two input channels, while the outputs connect to the appropriate RS-232 conductors. This configuration is useful when legacy peripherals use bipolar serial signaling but the controller operates at TTL levels. The circuit requires positive and negative supply rails, suitable local bypassing, and careful treatment of signal ground. Check the receiver's input thresholds, cable length, and capacitive loading before finalizing the interface because the published 20 kbit/s rate is specified with a full 2500-pF load.
推薦
Short-Distance Equipment-to-Equipment Communication
The SN75150D supports short-distance equipment-to-equipment communication links based on relatively short single lines. Its TIA/EIA-232-F orientation and 20 kbit/s rate make it appropriate for legacy serial ports, service interfaces, and control connections between cabinets or instruments. The transmit-only architecture allows a compact board to add two outbound channels without duplicating receiver circuitry. For reliable operation, calculate the aggregate load presented by cable capacitance, connector capacitance, protection components, and the receiving device. Keep the signal and return paths appropriately paired and terminate the interface according to the receiving equipment's expectations.
推薦
MOS-Device Interface Driving
The Texas Instruments SN75150 product page identifies driving MOS devices as an additional use for the SN75150 family. The bipolar RS-232 outputs can deliver a stronger, polarity-aware signal than a bare logic output, which is useful when the connected device requires a defined positive or negative input level. The implementation must account for the MOS input's voltage limits, the driver's output levels, supply sequencing, and any input clamp behavior. Do not treat the line-driver output as a general-purpose power output. Confirm that the load is within the published drive capability and that sustained shorts or abnormal cable conditions remain compatible with the device's protection characteristics.
推薦
Legacy Serial Port Expansion
Two SN75150D drivers can expand a design's available RS-232 transmit channels when one interface controller does not provide enough outputs. Each driver converts a compatible logic signal into a separate bipolar output, enabling status, command, or data signals to reach legacy equipment. The added channels still share the same supply and return constraints as other RS-232 transmitters. Place the IC close to the connector or protection devices, provide local supply bypassing, and avoid long stubs from the driver to the connector. Confirm that the receiving devices accept the generated levels and that the aggregate wiring capacitance does not degrade the intended 20 kbit/s data rate.
推薦
推薦產品摘要
工程參考資料,適用於 SN75150D — 比較、設計指引及合規資訊。
選型指南
設計說明
Place the SN75150D close to the RS-232 connector or protection network. Keep each driver output on a controlled route with an appropriate return path, and separate these routes from clocks, ADC inputs, and sensitive analog signals. Provide local supply bypassing for both 12-V and -12-V rails and verify that connector and protection-component capacitance does not exceed the conditions associated with the published 20 kbit/s rate.
Do not assume that the SN75150D implements a complete RS-232 port. It contains two drivers and no receivers, so bidirectional communication requires another interface device. Also confirm that logic levels, supply polarity, and output voltage limits match the connected equipment. A pin-compatible footprint alone is insufficient for a replacement because enable, shutdown, fault, or receiver functions may differ between otherwise similar driver packages.
Evaluate the complete channel rather than only the driver output. Include cable capacitance, connector capacitance, protection devices, receiver input loading, and any stubs in the capacitive budget. The SN75150D is rated for 20 kbit/s with a full 2500-pF load, so a slower data rate or longer cable may be required when total loading is higher. Preserve the RS-232 signal-to-return relationship and use the manufacturer's electrical limits when checking output behavior.
合規資訊
The available product information does not state RoHS, REACH, lead-free, halogen-free, or conflict-minerals status. The SN75150 is not identified as an automotive-qualified AEC-Q100 device.