TJA1021T/20/CM - 20 kBd LIN Transceiver | NXP
MPN: TJA1021T/20/CM ✓ فعالTJA1021T/20/CM جائزہ
A LIN transceiver, also called a LIN physical-layer interface, is a vehicle-network interface IC that converts digital controller signals into the dominant and recessive levels used on a LIN subnetwork. In the product hierarchy, a LIN transceiver belongs to the LIN bus interface family, which is part of automotive interface ICs and broader vehicle communication semiconductors. It is intended for low-cost, single-wire, in-vehicle subnetworks connecting sensors, actuators, switches, and electronic control units.
The TJA1021T/20/CM provides a maximum specified LIN transmission speed of 20 kBd. Its optimized slew-rate control helps reduce electromagnetic emissions, an important consideration when the transceiver is placed beside motors, relays, solenoids, or other switching loads. The device also includes bus-fault protection, local wake-up, bus wake-up, TXD timeout protection, low-power mode, and thermal shutdown protection. The /20 speed grade is intended for LIN 2.x networks rather than the lower-speed 10.4 kBd grade.
The TJA1021 is designed for both LIN master and LIN slave nodes and converts controller transmit data into a LIN bus signal. It also provides received bus data to the host controller. NXP identifies the family as pin-compatible with the TJA1020 and MC33662(B), enabling design migration within established LIN hardware. The TJA1021BT variant uses a later SOI3+ process and is identified as a pin-to-pin and hardware/software-compatible drop-in replacement for the TJA1021T/20.
Typical applications include vehicle body and comfort modules, door controls, seat and lighting controllers, climate-control panels, sensor interfaces, ambient-temperature sensing, small motor and actuator controllers, and general automotive LIN subnets. The single-wire bus architecture and 20 kBd capability suit distributed networks where several low-cost nodes exchange commands and diagnostic data over one conductor.
When laying out the circuit, place the transceiver and LIN interface protection components close to the connector and keep the LIN trace away from sensitive analog and high-speed digital routes. Confirm that the selected external transceiver protection supports the vehicle battery environment. If the host controller uses a voltage domain different from the transceiver supply, verify the RXD and TXD logic levels and the purpose of any VIO pin in the selected package variant before finalizing the schematic.
This page combines the manufacturer electrical and compatibility information with practical interface guidance, application-specific design context, a parameter comparison, and verified same-footprint alternatives. It is intended to help engineers evaluate the TJA1021T/20/CM for LIN 2.x automotive networks without overlooking speed grade, protection, protocol, or layout requirements.
کے لیے ڈراپ اِن متبادل TJA1021T/20/CM — یکساں پیکیج، پن سے پن مطابقت پذیر۔ مختلف پیکیج والے پرزے جن کے لیے PCB دوبارہ کام درکار ہو، شامل نہیں ہیں۔
اس سیریز میں مختلف ورژن
اسی سیریز کے ماڈلز جو ڈراپ اِن مطابقت رکھتے ہیں TJA1021T/20/CM (یکساں فارم فیکٹر اور فٹ پرنٹ) — میں مختلف Product Type, Package, Package Type.
TJA1021BT
✅ ڈراپ-اِن📋 حوالہ جاتی متبادل (کیٹلاگ میں نہیں)
TJA1021T/20/C
✅ ڈراپ-اِنقیمت کے لیے رابطہ کریں
ڈیٹا شیٹ دیکھیں →TJA1020T/N1
✅ ڈراپ-اِنقیمت کے لیے رابطہ کریں
ڈیٹا شیٹ دیکھیں →MC33662JEF
✅ ڈراپ-اِنقیمت کے لیے رابطہ کریں
ڈیٹا شیٹ دیکھیں →TJA1021B/20
✅ ڈراپ-اِن📋 حوالہ جاتی متبادل (کیٹلاگ میں نہیں)
TJA1021T/20/CM تفصیلات
| Product Type | LIN bus transceiver |
| LIN Configuration | Master or slave interface |
| آپریٹنگ سپلائی وولٹیج | 5.5 V to 27 V |
| Maximum LIN Baud Rate | 20 kBd |
| Supported LIN Baud Rate Range | 1 kBd to 20 kBd |
| Supported LIN Standards | LIN 2.0, LIN 2.1, LIN 2.2, LIN 2.2A |
| Automotive Network Standard | SAE J2602 |
| International LIN Standard | ISO 17987-4:2016 |
| پیکیج | 8-pin SOIC |
| ماؤنٹنگ ٹائپ | Surface mount |
| Slew-Rate Control | Optimized for reduced electromagnetic emissions |
| Bus Fault Protection | Supported |
| Local Wake-Up | Supported |
| Bus Wake-Up | Supported |
| TXD Timeout Protection | Supported |
| Low-Power Mode | Supported |
| Thermal Shutdown Protection | Supported |
| Automotive Qualification | AEC-Q100 |
TJA1021T/20/CM پن کنفیگریشن
| پن 1 | LIN — LIN bus transceiver input and output |
| پن 2 | GND — Ground connection |
| پن 3 | VCC — Transceiver supply voltage |
| پن 4 | RXD — Received data output to the LIN controller |
| پن 5 | TXD — Transmit data input from the LIN controller |
| پن 6 | VIO — Logic-level supply for the controller interface |
| پن 7 | NC — Not connected |
| پن 8 | GND — Ground connection |
عام استعمالات
TJA1021T/20/CM کے لیے موزوں ہے 6 ایپلیکیشنs: Automotive Body Control Modules, Automotive Sensor Networks, Door and Lighting Control, Climate Control Panel Interfaces, Small Motor and Actuator Controllers, Industrial and Commercial LIN Gateways.
Automotive Body Control Modules
The TJA1021T/20/CM fits LIN nodes used by body-control modules for doors, locks, mirrors, seats, and lighting. Its 20 kBd capability supports faster LIN 2.x communication than legacy 10 kBd transceivers, while optimized slew-rate control helps limit electromagnetic emissions in a densely wired vehicle. The device operates from 5.5 V to 27 V and provides bus-fault protection, local and bus wake-up, TXD timeout protection, low-power operation, and thermal shutdown protection. These functions allow a compact body-control module to communicate reliably with remote actuators while limiting software and board complexity.
تجویز کردہ
Automotive Sensor Networks
The TJA1021T/20/CM can serve as the physical-layer interface for distributed automotive sensors that report temperature, position, pressure, or presence information over a LIN subnet. Its 1 kBd to 20 kBd operating range accommodates multiple LIN protocol revisions, and the /20 grade gives designers headroom for faster polling schedules. Integrated bus-fault and TXD timeout protection improve resilience against wiring faults or an unresponsive controller. The 8-pin SOIC package also keeps the interface compact enough for remote door, seat, climate, and exterior sensor modules where board area is constrained.
تجویز کردہ
Door and Lighting Control
The TJA1021T/20/CM is well suited to LIN-connected door modules and lighting controllers where multiple switches and actuators share a one-wire subnetwork. Communication up to 20 kBd allows the host controller to handle commands and status updates with less bus time than a 10 kBd-class interface. Optimized slew-rate control is valuable because door and lighting systems can be located near relays and switched loads that generate electromagnetic interference. Wake-up and low-power features allow parked nodes to reduce consumption while still supporting local or bus-generated remote activation.
تجویز کردہ
Climate Control Panel Interfaces
A TJA1021T/20/CM can connect climate-control buttons, rotary controls, and panel status lamps through a LIN subnetwork. The 20 kBd maximum speed supports efficient command and diagnostic exchanges, while operation from 5.5 V to 27 V accommodates typical automotive power conditions. Bus-fault protection and thermal shutdown protection add system-level robustness, and local wake-up allows a control panel to activate from a user input without keeping every network node fully powered. Optimized slew-rate control also helps contain emissions in passenger-compartment electronics where display, switch, and communication traces may share compact PCB space.
تجویز کردہ
Small Motor and Actuator Controllers
The TJA1021T/20/CM is appropriate for LIN-connected window, mirror, seat, latch, and small-pump actuator controllers where the physical bus must coexist with motor-switching circuitry. Its 20 kBd communication rate provides more host-controller bandwidth than a 10 kBd LIN interface, while slew-rate control helps reduce radiated emissions from the transceiver itself. The integrated protection functions support robust operation when the harness or connector is exposed to faults. Designers should still use appropriate bus protection and maintain a low-impedance return path between the transceiver, host controller, and vehicle ground.
تجویز کردہ
Industrial and Commercial LIN Gateways
The TJA1021T/20/CM can be used in a LIN-to-network gateway when an industrial or commercial system must preserve compatibility with automotive-style LIN peripherals. Its support for 1 kBd to 20 kBd and LIN 2.0 through LIN 2.2A allows the gateway to communicate with controllers and sensors using established LIN conventions. The 8-pin SOIC format simplifies integration beside a host processor or communications controller. Integrated bus-fault, TXD timeout, wake-up, low-power, and thermal protection features support dependable operation, while the external protection network must be selected for the actual harness voltage and transient requirements.
تجویز کردہ
تجویز کردہ پروڈکٹس کا خلاصہ
کے لیے انجینئرنگ ریفرنس ڈیٹا TJA1021T/20/CM — موازنہ، ڈیزائن رہنمائی، اور تعمیل کی معلومات۔
انتخاب کی گائیڈ
متبادلات کے ساتھ موازنہ
| پیرامیٹر | یہ پروڈکٹ | TJA1021BT | TJA1021T/20 | TJA1020 | MC33662(B) | TJA1021B/20 |
|---|---|---|---|---|---|---|
| Brand | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors |
| Package | 8-pin SOIC | 8-pin SOIC - same | 8-pin SOIC - same | 8-pin SOIC - same | 8-pin SOIC - same | 8-pin SOIC - same |
| Maximum LIN Baud Rate | 20 kBd | 20 kBd | 20 kBd | 10 kBd | 10 kBd | 20 kBd |
اہم امتیازی خصوصیات
- Higher communication rate than legacy pin-compatible devices (بمقابلہTJA1020)
- Modern-process drop-in option (بمقابلہTJA1021BT)
- Integrated fault and wake-up management (بمقابلہMC33662(B))
ڈیزائن نوٹس
Place the LIN transceiver close to the vehicle connector and route the LIN conductor as a short, controlled path away from relay coils, motor drives, and switching power nodes. Connect the transceiver ground to the host-controller ground through a low-impedance return, and install the external LIN protection network at the connector so transient current is diverted before reaching the IC. This arrangement preserves the benefit of the optimized slew-rate control while reducing radiated-emissions risk.
Design the 5.5 V to 27 V supply path for the TJA1021T/20/CM so that it remains within the transceiver's operating range during vehicle transients. Provide local high-frequency decoupling at VCC and, where used, VIO, with the return current connected close to the device. Do not rely on the host controller's supply rail to absorb wiring transients; use a protection network selected for the harness and connector requirements.
Avoid substituting a 10 kBd LIN device into a bus that must operate at 20 kBd. The TJA1020 and MC33662(B) are pin-compatible with the TJA1021 family, but the maximum communication speed and protection behavior differ. Confirm the bus baud rate, LIN protocol revision, wake-up method, TXD timeout behavior, logic levels, and external protection network before treating either device as a production replacement.
Use the dominant and recessive levels defined by the LIN physical layer, and keep the bus topology within the requirements of the selected LIN standard. Avoid placing long stubs or unnecessary test points along the LIN trace. The TJA1021's optimized slew-rate control helps reduce electromagnetic emissions, but correct return-path geometry, connector placement, and protection remain essential for dependable communication in a vehicle electrical environment.
تعمیل کی معلومات
The product listing identifies the TJA1021T/20/CM as an automotive AEC-Q100 device. RoHS, REACH, lead-free, halogen-free, and conflict-minerals declarations for the exact NXP ordering code are not stated in the manufacturer excerpts used for this record.