NXP Semiconductors

TJA1021T/20/CM - 20 kBd LIN Transceiver | NXP

MPN: TJA1021T/20/CM ✓ فعال
5.5 V to 27 V Vdss LIN 2.0, LIN 2.1, LIN 2.2, LIN 2.2A Rds(on) 8-pin SOIC Package
حداقل سفارش: 1 |

TJA1021T/20/CM نمای کلی

The NXP Semiconductors TJA1021T/20/CM is a single LIN bus transceiver operating from 5.5 V to 27 V, with communication speeds from 1 kBd to 20 kBd, and it is packaged in an 8-pin SOIC. It interfaces an automotive LIN master or slave protocol controller with the physical LIN bus while supporting LIN 2.0, LIN 2.1, LIN 2.2, LIN 2.2A, SAE J2602, and ISO 17987-4:2016.

A LIN transceiver, also called a LIN physical-layer interface, is a vehicle-network interface IC that converts digital controller signals into the dominant and recessive levels used on a LIN subnetwork. In the product hierarchy, a LIN transceiver belongs to the LIN bus interface family, which is part of automotive interface ICs and broader vehicle communication semiconductors. It is intended for low-cost, single-wire, in-vehicle subnetworks connecting sensors, actuators, switches, and electronic control units.

The TJA1021T/20/CM provides a maximum specified LIN transmission speed of 20 kBd. Its optimized slew-rate control helps reduce electromagnetic emissions, an important consideration when the transceiver is placed beside motors, relays, solenoids, or other switching loads. The device also includes bus-fault protection, local wake-up, bus wake-up, TXD timeout protection, low-power mode, and thermal shutdown protection. The /20 speed grade is intended for LIN 2.x networks rather than the lower-speed 10.4 kBd grade.

The TJA1021 is designed for both LIN master and LIN slave nodes and converts controller transmit data into a LIN bus signal. It also provides received bus data to the host controller. NXP identifies the family as pin-compatible with the TJA1020 and MC33662(B), enabling design migration within established LIN hardware. The TJA1021BT variant uses a later SOI3+ process and is identified as a pin-to-pin and hardware/software-compatible drop-in replacement for the TJA1021T/20.

Typical applications include vehicle body and comfort modules, door controls, seat and lighting controllers, climate-control panels, sensor interfaces, ambient-temperature sensing, small motor and actuator controllers, and general automotive LIN subnets. The single-wire bus architecture and 20 kBd capability suit distributed networks where several low-cost nodes exchange commands and diagnostic data over one conductor.

When laying out the circuit, place the transceiver and LIN interface protection components close to the connector and keep the LIN trace away from sensitive analog and high-speed digital routes. Confirm that the selected external transceiver protection supports the vehicle battery environment. If the host controller uses a voltage domain different from the transceiver supply, verify the RXD and TXD logic levels and the purpose of any VIO pin in the selected package variant before finalizing the schematic.

This page combines the manufacturer electrical and compatibility information with practical interface guidance, application-specific design context, a parameter comparison, and verified same-footprint alternatives. It is intended to help engineers evaluate the TJA1021T/20/CM for LIN 2.x automotive networks without overlooking speed grade, protection, protocol, or layout requirements.

جایگزین‌های drop-in برای TJA1021T/20/CM — همان پکیج، سازگار پین‌به‌پین. قطعات با پکیج متفاوت که نیاز به تغییر PCB دارند مستثنی هستند.

گونه‌ها در این سری

مدل‌های هم‌سری که جایگزین مستقیم هستند برای TJA1021T/20/CM (همان فرم‌فاکتور و فوت‌پرینت) — متفاوت در Product Type, Package, Package Type.

NXP Semiconductors
Product Type: LIN Bus Physical-Layer Transceiver
Package Type: SOIC-8
NXP Semiconductors
Package: 8-pin SO package
Package Type: SOIC-8 surface-mount package
NXP Semiconductors
Product Type: LIN Transceiver (single-wire bus PHY)
Package: 8-SO (SOIC-8) SMD

TJA1021BT

✅ جایگزین مستقیم
📦 8-pin SOIC
Uses the newer SOI3+ process while retaining 20 kBd operation, pin-to-pin compatibility, and hardware/software compatibility; key ratings match at 100%.

📋 جایگزین مرجع (خارج از کاتالوگ)

TJA1021T/20/C

✅ جایگزین مستقیم
NXP Semiconductors
📦 8-pin SOIC
LIN Transceiver (single-wire bus PHY) · LIN 2.0 / 2.1 / 2.2 / 2.2A / SAE J2602 / ISO 17987-4:2016 · 20 kBd (/20 variant) · 1 kBd · 3.0 V to 5.5 V (typical 5 V) · 5 V to 27 V (extended -27 V to +40 V with load dump) · 1 (half-duplex LIN bus + TXD/RXD logic) · 8-SO (SOIC-8) SMD

برای قیمت تماس بگیرید

مشاهده دیتاشیت ←

TJA1020T/N1

✅ جایگزین مستقیم
NXP Semiconductors
📦 8-pin SOIC
LIN bus transceiver · LINbus serial interface · Half LINbus transceiver · NXP Semiconductors · 8-pin SO package · SOIC-8 surface-mount package · 8 pins · End of Life

برای قیمت تماس بگیرید

مشاهده دیتاشیت ←

MC33662JEF

✅ جایگزین مستقیم
NXP Semiconductors
📦 8-pin SOIC
LIN Bus Physical-Layer Transceiver · 1 transmitter and 1 receiver · LINbus · 13.5 V · -40 °C · 125 °C · 8 pins · SOIC-8

برای قیمت تماس بگیرید

مشاهده دیتاشیت ←

TJA1021B/20

✅ جایگزین مستقیم
📦 8-pin SOIC
Uses the SOI3+ process like TJA1021BT while retaining the /20 speed class; electrical key ratings match, with the main distinction being the manufacturer ordering code.

📋 جایگزین مرجع (خارج از کاتالوگ)

TJA1021T/20/CM مشخصات

Product Type LIN bus transceiver
LIN Configuration Master or slave interface
ولتاژ تغذیه کاری 5.5 V to 27 V
Maximum LIN Baud Rate 20 kBd
Supported LIN Baud Rate Range 1 kBd to 20 kBd
Supported LIN Standards LIN 2.0, LIN 2.1, LIN 2.2, LIN 2.2A
Automotive Network Standard SAE J2602
International LIN Standard ISO 17987-4:2016
بسته‌بندی 8-pin SOIC
نوع نصب Surface mount
Slew-Rate Control Optimized for reduced electromagnetic emissions
Bus Fault Protection Supported
Local Wake-Up Supported
Bus Wake-Up Supported
TXD Timeout Protection Supported
Low-Power Mode Supported
Thermal Shutdown Protection Supported
Automotive Qualification AEC-Q100

پیکربندی پین TJA1021T/20/CM

SOIC-8 Package Pinout Diagram SOIC-8 8-pin small outline IC, 3.9x4.9mm, P1.27mm, JEDEC MS-012. 1 8 2 7 3 6 4 5 SOIC-8
پین 1 LIN — LIN bus transceiver input and output
پین 2 GND — Ground connection
پین 3 VCC — Transceiver supply voltage
پین 4 RXD — Received data output to the LIN controller
پین 5 TXD — Transmit data input from the LIN controller
پین 6 VIO — Logic-level supply for the controller interface
پین 7 NC — Not connected
پین 8 GND — Ground connection

کاربردهای معمول

TJA1021T/20/CM مناسب است برای 6 کاربردs: Automotive Body Control Modules, Automotive Sensor Networks, Door and Lighting Control, Climate Control Panel Interfaces, Small Motor and Actuator Controllers, Industrial and Commercial LIN Gateways.

🚗

Automotive Body Control Modules

The TJA1021T/20/CM fits LIN nodes used by body-control modules for doors, locks, mirrors, seats, and lighting. Its 20 kBd capability supports faster LIN 2.x communication than legacy 10 kBd transceivers, while optimized slew-rate control helps limit electromagnetic emissions in a densely wired vehicle. The device operates from 5.5 V to 27 V and provides bus-fault protection, local and bus wake-up, TXD timeout protection, low-power operation, and thermal shutdown protection. These functions allow a compact body-control module to communicate reliably with remote actuators while limiting software and board complexity.

🧩

Automotive Sensor Networks

The TJA1021T/20/CM can serve as the physical-layer interface for distributed automotive sensors that report temperature, position, pressure, or presence information over a LIN subnet. Its 1 kBd to 20 kBd operating range accommodates multiple LIN protocol revisions, and the /20 grade gives designers headroom for faster polling schedules. Integrated bus-fault and TXD timeout protection improve resilience against wiring faults or an unresponsive controller. The 8-pin SOIC package also keeps the interface compact enough for remote door, seat, climate, and exterior sensor modules where board area is constrained.

💡

Door and Lighting Control

The TJA1021T/20/CM is well suited to LIN-connected door modules and lighting controllers where multiple switches and actuators share a one-wire subnetwork. Communication up to 20 kBd allows the host controller to handle commands and status updates with less bus time than a 10 kBd-class interface. Optimized slew-rate control is valuable because door and lighting systems can be located near relays and switched loads that generate electromagnetic interference. Wake-up and low-power features allow parked nodes to reduce consumption while still supporting local or bus-generated remote activation.

📱

Climate Control Panel Interfaces

A TJA1021T/20/CM can connect climate-control buttons, rotary controls, and panel status lamps through a LIN subnetwork. The 20 kBd maximum speed supports efficient command and diagnostic exchanges, while operation from 5.5 V to 27 V accommodates typical automotive power conditions. Bus-fault protection and thermal shutdown protection add system-level robustness, and local wake-up allows a control panel to activate from a user input without keeping every network node fully powered. Optimized slew-rate control also helps contain emissions in passenger-compartment electronics where display, switch, and communication traces may share compact PCB space.

⚡

Small Motor and Actuator Controllers

The TJA1021T/20/CM is appropriate for LIN-connected window, mirror, seat, latch, and small-pump actuator controllers where the physical bus must coexist with motor-switching circuitry. Its 20 kBd communication rate provides more host-controller bandwidth than a 10 kBd LIN interface, while slew-rate control helps reduce radiated emissions from the transceiver itself. The integrated protection functions support robust operation when the harness or connector is exposed to faults. Designers should still use appropriate bus protection and maintain a low-impedance return path between the transceiver, host controller, and vehicle ground.

🏭

Industrial and Commercial LIN Gateways

The TJA1021T/20/CM can be used in a LIN-to-network gateway when an industrial or commercial system must preserve compatibility with automotive-style LIN peripherals. Its support for 1 kBd to 20 kBd and LIN 2.0 through LIN 2.2A allows the gateway to communicate with controllers and sensors using established LIN conventions. The 8-pin SOIC format simplifies integration beside a host processor or communications controller. Integrated bus-fault, TXD timeout, wake-up, low-power, and thermal protection features support dependable operation, while the external protection network must be selected for the actual harness voltage and transient requirements.

خلاصه محصولات پیشنهادی

TJA1020 Pin-compatible NXP LIN transceiver alternative استفاده‌شده در: Automotive Body Control Modules, Door and Lighting Control, Small Motor and Actuator Controllers, Industrial and Commercial LIN Gateways MC33662(B) Pin-compatible NXP LIN interface alternative استفاده‌شده در: Automotive Body Control Modules, Door and Lighting Control, Small Motor and Actuator Controllers TJA1021BT Drop-in SOI3+ LIN transceiver replacement استفاده‌شده در: Automotive Sensor Networks, Climate Control Panel Interfaces, Industrial and Commercial LIN Gateways TJA1021B/20 20 kBd SOI3+ family alternative استفاده‌شده در: Automotive Sensor Networks, Climate Control Panel Interfaces
What is the TJA1021T/20/CM and what does it do?
The TJA1021T/20/CM is a single LIN bus transceiver that connects an automotive LIN master or slave controller to the physical one-wire bus. According to the NXP manufacturer datasheet, it operates from 5.5 V to 27 V, supports baud rates from 1 kBd to 20 kBd, and converts controller TXD data into a LIN bus signal while returning received data through RXD.
What is the maximum baud rate of the TJA1021T/20/CM?
The TJA1021T/20/CM supports LIN communication up to 20 kBd. The NXP manufacturer datasheet identifies the /20 and B variants as optimized for the maximum specified LIN speed of 20 kBd, while the /10 and A variants target 10.4 kBd. This makes the /20 grade appropriate for LIN 2.x subnets designed around the faster 20 kBd operating limit.
Which LIN standards are supported by the TJA1021T/20/CM?
The TJA1021T/20/CM supports LIN 2.0, LIN 2.1, LIN 2.2, LIN 2.2A, SAE J2602, and ISO 17987-4:2016 for 12 V systems. According to the NXP manufacturer datasheet, this combination covers common in-vehicle LIN subnetworks operating between 1 kBd and 20 kBd, making the device suitable for body, comfort, sensor, and actuator networks.
Where can I download the TJA1021T/20/CM datasheet PDF?
The official TJA1021T/20/CM datasheet PDF is available from NXP at https://www.nxp.com/docs/en/data-sheet/TJA1021.pdf. It contains the electrical characteristics, application information, pin descriptions, LIN interface behavior, and ordering information for the TJA1021 family. Use the TJA1021T/20 variant entry when reviewing the 20 kBd operating conditions.
Where can I find the TJA1021T/20/CM pinout?
The TJA1021T/20/CM pinout is shown in the NXP TJA1021 manufacturer datasheet, with the 8-pin SOIC connection and pin-description table included alongside the application schematic. The principal bus and logic functions are LIN, supply, ground, RXD, TXD, and the voltage-interface-related connections specified for this package variant.
Can the TJA1021BT replace the TJA1021T/20/CM?
Yes, the TJA1021BT is a drop-in replacement for the TJA1021T/20 because it is pin-to-pin and hardware/software compatible. NXP states that the TJA1021BT uses its newer SOI3+ process, while both devices support the 20 kBd LIN operating class. The replacement assessment assumes the same 8-pin footprint and matching supply, logic, and bus implementation.
What is the difference between TJA1021T/20 and TJA1021T/10?
The principal difference is the optimized maximum LIN transmission speed: the TJA1021T/20 targets 20 kBd, while the TJA1021T/10 is optimized for 10.4 kBd as specified by SAE J2602. Both belong to the TJA1021 family and use the 8-pin SOIC format, but a system operating above 10.4 kBd should select the /20 grade and confirm that every node supports the faster bus rate.
When should I choose the TJA1021T/20/CM over another LIN transceiver?
Choose the TJA1021T/20/CM when a new LIN 2.x node needs 20 kBd operation, 5.5 V to 27 V supply compatibility, slew-rate-controlled emission performance, and integrated fault and wake-up protection. Select an alternative only after confirming package, pinout, logic levels, speed grade, protection method, wake-up behavior, and software expectations match the existing design.
Is the TJA1021T/20/CM suitable for automotive body and sensor networks?
Yes, the TJA1021T/20/CM is suitable for automotive LIN subnets such as body-control, door, lighting, climate-control, sensor, and actuator networks. The NXP manufacturer datasheet identifies the family for in-vehicle communication at 1 kBd to 20 kBd and lists SAE J2602 and ISO 17987-4:2016 support, providing a standardized basis for low-cost distributed vehicle nodes.
What protection features does the TJA1021T/20/CM provide?
The TJA1021T/20/CM includes bus-fault protection, local wake-up, bus wake-up, TXD timeout protection, low-power mode, and thermal shutdown protection. These features support robust vehicle-network behavior where transient disturbances, controller faults, or low-power operation must be managed. The external LIN bus still normally needs application-appropriate protection for the vehicle environment and connector.
What is the best drop-in replacement for the TJA1021T/20/CM?
The TJA1021BT is the strongest directly documented drop-in replacement because NXP identifies it as pin-to-pin and hardware/software compatible with the TJA1021T/20. It retains the 20 kBd class while using the newer SOI3+ process. The TJA1020 and MC33662(B) are also identified as pin-compatible, but their speed and feature details must be checked against the original system requirements.
What is the best NXP equivalent for the TJA1021T/20/CM?
The best NXP equivalent is the TJA1021BT because NXP explicitly describes it as a pin-to-pin and hardware/software-compatible drop-in replacement for the TJA1021T/20. It keeps the 20 kBd operating class and the same 8-pin implementation while changing to the newer SOI3+ process. Existing bus protection and software should still be checked for any application-specific requirements.
Is the TJA1021T/20/CM the same as the TJA1020?
No, the TJA1021T/20/CM and TJA1020 are related but not identical devices. NXP states that the TJA1021 is pin-compatible with the TJA1020, which supports board-level substitution options, but the TJA1021 adds a broader set of fault protection, wake-up, low-power, and slew-rate-controlled emission features. Verify speed grade and software behavior before substitution.
Can the TJA1021T/20/CM replace the MC33662(B)?
The TJA1021T/20/CM is pin-compatible with MC33662(B) according to the NXP manufacturer datasheet, making it a credible board-level replacement option. The devices are not necessarily identical in every operating characteristic, so verify baud-rate limits, LIN protocol revision, transceiver protection strategy, wake-up behavior, pin-level logic, and host-controller expectations before production use.
How should a LIN bus network using the TJA1021T/20/CM be laid out?
Route the one-wire LIN bus as a controlled, direct path from the transceiver to the connector, with protection placed close to the external connection. Keep the bus away from noisy motor, relay, and switching-node routes, and minimize the ground impedance shared by the transceiver and its host controller. The NXP manufacturer datasheet emphasizes optimized slew-rate control to help reduce electromagnetic emissions.
Where can I buy the TJA1021T/20/CM and check its lead time?
Use the Request a Quote form on this page to request the current price, stock position, lead time, and order quantity for the TJA1021T/20/CM. The part is identified in the manufacturer and distributor listings as an 8-pin SOIC LIN transceiver for 20 kBd operation. A firm production schedule should be confirmed for the selected reel packaging code and required quantity.

داده‌های مرجع مهندسی برای TJA1021T/20/CM — مقایسه، راهنمای طراحی و اطلاعات انطباق.

راهنمای انتخاب

Choose the TJA1021T/20/CM for a new LIN 2.x design that requires operation up to 20 kBd, a 5.5 V to 27 V automotive supply range, optimized slew-rate control, and integrated bus-fault, wake-up, timeout, low-power, and thermal protection. Choose the TJA1021BT when you want the same pin-to-pin and hardware/software-compatible functionality implemented on the newer SOI3+ process. The TJA1021T/20 is the equivalent speed-grade device when a different ordering configuration is needed. Consider the TJA1020 or MC33662(B) only for legacy 10 kBd networks and after checking wake-up behavior, protection thresholds, logic levels, and controller compatibility. For every candidate, verify the 8-pin footprint, LIN protocol revision, bus topology, and external protection network before releasing a PCB or production design.

مقایسه با جایگزین‌ها

پارامتر این محصول TJA1021BT TJA1021T/20 TJA1020 MC33662(B) TJA1021B/20
Brand NXP Semiconductors NXP Semiconductors NXP Semiconductors NXP Semiconductors NXP Semiconductors NXP Semiconductors
Package 8-pin SOIC 8-pin SOIC - same 8-pin SOIC - same 8-pin SOIC - same 8-pin SOIC - same 8-pin SOIC - same
Maximum LIN Baud Rate 20 kBd 20 kBd 20 kBd 10 kBd 10 kBd 20 kBd

تفاوت‌های کلیدی

  • Higher communication rate than legacy pin-compatible devices (در مقابلTJA1020)
  • Modern-process drop-in option (در مقابلTJA1021BT)
  • Integrated fault and wake-up management (در مقابلMC33662(B))

یادداشت‌های طراحی

Place the LIN transceiver close to the vehicle connector and route the LIN conductor as a short, controlled path away from relay coils, motor drives, and switching power nodes. Connect the transceiver ground to the host-controller ground through a low-impedance return, and install the external LIN protection network at the connector so transient current is diverted before reaching the IC. This arrangement preserves the benefit of the optimized slew-rate control while reducing radiated-emissions risk.

Design the 5.5 V to 27 V supply path for the TJA1021T/20/CM so that it remains within the transceiver's operating range during vehicle transients. Provide local high-frequency decoupling at VCC and, where used, VIO, with the return current connected close to the device. Do not rely on the host controller's supply rail to absorb wiring transients; use a protection network selected for the harness and connector requirements.

Avoid substituting a 10 kBd LIN device into a bus that must operate at 20 kBd. The TJA1020 and MC33662(B) are pin-compatible with the TJA1021 family, but the maximum communication speed and protection behavior differ. Confirm the bus baud rate, LIN protocol revision, wake-up method, TXD timeout behavior, logic levels, and external protection network before treating either device as a production replacement.

Use the dominant and recessive levels defined by the LIN physical layer, and keep the bus topology within the requirements of the selected LIN standard. Avoid placing long stubs or unnecessary test points along the LIN trace. The TJA1021's optimized slew-rate control helps reduce electromagnetic emissions, but correct return-path geometry, connector placement, and protection remain essential for dependable communication in a vehicle electrical environment.

اطلاعات انطباق

RoHS
Unknown
REACH
Unknown
AEC-Q100
Qualified
بدون سرب
Unknown
بدون هالوژن
Unknown
مواد معدنی درگیری
Unknown

The product listing identifies the TJA1021T/20/CM as an automotive AEC-Q100 device. RoHS, REACH, lead-free, halogen-free, and conflict-minerals declarations for the exact NXP ordering code are not stated in the manufacturer excerpts used for this record.

جستجوهای مرتبط

tja1021t 20 cm datasheet tja1021t datasheet tja1021t lin transceiver tja1021t pinout TJA1021T/20/CM datasheet TJA1021T/20/CM pinout TJA1021T/20/CM equivalent TJA1021T/20/CM replacement TJA1021T/20/CM cross reference TJA1021T/20/CM automotive TJA1021T/20/CM price TJA1021T/20/CM stock NXP TJA1021T/20/CM TJA1021T/20 vs TJA1021BT 20 kBd 8-pin LIN transceiver

قطعات و اصطلاحات مرتبط

NXP Semiconductors TJA1021T/20/CM TJA1021T TJA1021BT TJA1020 MC33662(B) LIN transceiver LIN physical-layer interface automotive interface IC vehicle communication semiconductor one-wire LIN bus SOIC-8 surface-mount package 20 kBd 5.5 V to 27 V LIN 2.0 LIN 2.1 LIN 2.2A SAE J2602 ISO 17987-4:2016 AEC-Q100 slew-rate control electromagnetic emissions bus-fault protection SOI3+
استعلام قیمت سریع RFQ
جزئیات کامل را پر کنید — تیم فروش ما ظرف 24 ساعت پاسخ خواهد داد
شماره قطعه سازنده بسته‌بندی QTY قیمت هدف قیمت کل
✓
استعلام قیمت ارسال شد!

ظرف ۲۴ ساعت به ایمیل شما پاسخ خواهیم داد

1
درخواست قیمت ارسال شد
2
استعلام دریافت شد
3
سفارش ثبت شد
4
پرداخت
5
ارسال شد
6
تحویل داده شد
مشاهده جزئیات RFQ