TJA1028T/5V0/20:11 - 20 kbaud LIN Transceiver | NXP
MPN: TJA1028T/5V0/20:11 ✓ فعالTJA1028T/5V0/20:11 جائزہ
A LIN transceiver is an interface IC that connects a microcontroller or other host controller to a low-cost, single-wire Local Interconnect Network bus. Within the product hierarchy, the TJA1028 belongs to the LIN transceiver family, which falls under communication transceivers, interface ICs, and integrated semiconductor devices. LIN buses commonly connect vehicle body modules, sensors, switches, actuators, and door or lighting controls over a slow, robust serial network.
The device supports LIN 2.0, LIN 2.1, SAE J2602, and ISO 17987-4:2016 for 12 V systems. Its 5.0 V regulator variant has a 4.9 V to 5.1 V output range, while the 20 kbaud ordering code identifies the bus-speed configuration. The SO-8 package supports surface-mount assembly, and the 6 microsecond propagation-delay value allows reliable signal timing in typical automotive body-electronics networks.
The integrated regulator is a low-drop design intended to operate from the vehicle battery while providing a local 5.0 V supply. This architecture helps create compact LIN nodes without a separate discrete regulator. Because the regulator can deliver only 70 mA, the load must remain within that limit, and supply pins still require appropriate local filtering and protection for automotive transients.
Typical uses include LIN door modules, seat and window controls, climate-control panels, body-control sensor interfaces, switch modules, and compact industrial LIN nodes. The 70 mA regulator output can support low-power sensors and control electronics, although it should not be used to power high-current actuators, lamps, or motors.
When laying out the circuit, keep the LIN-bus connection physically separated from sensitive analog or high-speed digital traces, follow the application circuit shown in the NXP datasheet, and validate the external component values for the intended network. Check the regulator load current and supply decoupling before adding additional local loads.
This page brings together the manufacturer specifications, verified distributor availability information, practical design notes, and drop-in replacement analysis. It also explains the functional differences between documented TJA1028 variants so engineers can select the correct ordering code without relying on incomplete distributor summaries.
کے لیے ڈراپ اِن متبادل TJA1028T/5V0/20:11 — یکساں پیکیج، پن سے پن مطابقت پذیر۔ مختلف پیکیج والے پرزے جن کے لیے PCB دوبارہ کام درکار ہو، شامل نہیں ہیں۔
TJA1028DT
✅ ڈراپ-اِن📋 حوالہ جاتی متبادل (کیٹلاگ میں نہیں)
TJA1028T/5V0/20
✅ ڈراپ-اِن📋 حوالہ جاتی متبادل (کیٹلاگ میں نہیں)
TJA1028T/5V0/20:11 تفصیلات
| Product Type | LIN transceiver with integrated voltage regulator |
| LIN Compliance | LIN 2.0, LIN 2.1, SAE J2602 |
| Automotive Standard | ISO 17987-4:2016 (12 V) |
| Bus Speed | 20 kbaud |
| Integrated Regulator Output | 5.0 V |
| Regulator Output Range | 4.9 V to 5.1 V |
| Regulator Maximum Output Current | 70 mA |
| آپریٹنگ سپلائی وولٹیج | 5 V |
| Propagation Delay Time | 6 us |
| پیکیج | SO-8 |
| Package Type | 8-pin SOIC |
| ماؤنٹنگ اسٹائل | SMD/SMT |
| Packaging | Reel |
| Transceiver Configuration | 1/1 half-duplex LIN transceiver |
| ESD Protection | Strong electrostatic discharge protection |
| RoHS اسٹیٹس | Compliant |
TJA1028T/5V0/20:11 8-pin soic پن کنفیگریشن گائیڈ
TJA1028T/5V0/20:11 (8-pin soic پیکیج) کے لیے پن کنفیگریشن۔ پن نمبرنگ، فنکشنز اور کنکشن ڈایاگرامز مینوفیکچرر کے ڈیٹا شیٹ میں بیان کیے گئے ہیں۔ درست فٹ پرنٹ اور سولڈرنگ رہنما ہدایات کے لیے اسی سے رجوع کریں۔
کے لیے تفصیلی پن آؤٹ ڈیٹا دستیاب نہیں TJA1028T/5V0/20:11.
رجوع کریں ڈیٹا شیٹ مکمل پن کنفیگریشن کے لیے۔
عام استعمالات
TJA1028T/5V0/20:11 کے لیے موزوں ہے 6 ایپلیکیشنs: Automotive LIN Door Module, Body Sensor Interface Node, Climate-Control Panel Interface, Automotive Switch and Illumination Module, Compact Industrial LIN Controller, Seat and Window Control Interface.
Automotive LIN Door Module
The TJA1028T/5V0/20:11 fits a door control module that accepts LIN commands from a body controller and drives local switches or indicator logic. Its 20 kbaud LIN interface supports LIN 2.0 and LIN 2.1, while the integrated 5.0 V regulator supplies up to 70 mA to the host controller and related low-power circuitry. This integration reduces the number of discrete power components in a compact SO-8 node. Design the regulator load conservatively because motor, lamp, and lock actuators require separate drive stages rather than the 70 mA regulator output.
تجویز کردہ
Body Sensor Interface Node
The TJA1028T/5V0/20:11 is suitable for a remote LIN sensor node that combines a 12 V automotive bus connection with a regulated 5.0 V local rail. Its 70 mA regulator capability can power a low-power sensing front end and host electronics without a separate regulator, provided the aggregate current remains within that limit. The device's SAE J2602 and ISO 17987-4:2016 support, together with strong ESD protection, helps simplify qualification for body-mounted modules. Add input filtering and transient protection according to the application guidance for the vehicle platform.
تجویز کردہ
Climate-Control Panel Interface
The TJA1028T/5V0/20:11 can serve as the LIN interface for a climate-control panel or HVAC switch module. The 20 kbaud bus rate matches the low-speed communication used by many distributed body systems, and the 5.0 V regulator output provides a convenient local supply for a microcontroller, button decoder, or indicator driver. The integrated architecture reduces board area in space-constrained panels. Because the 70 mA limit applies across the regulator output, illuminate indicators through an appropriate driver rather than loading the transceiver's regulator directly.
تجویز کردہ
Automotive Switch and Illumination Module
The TJA1028T/5V0/20:11 is a practical choice for a distributed LIN switch module that reads local inputs and reports their state to a body controller. Its LIN 2.1 compatibility supports modern low-speed networks, while the integrated regulator supplies low-power logic from one SO-8 package. The 6 us propagation-delay specification supports deterministic communication in standard LIN timing arrangements. Use a separate transistor or LED driver for illumination because the transceiver regulator cannot support lamp or actuator current directly.
تجویز کردہ
Compact Industrial LIN Controller
The TJA1028T/5V0/20:11 can also support compact industrial LIN nodes where a controller, sensor, or remote actuator shares a single-wire bus. The integrated 5.0 V, 70 mA regulator simplifies the local power architecture, while 20 kbaud operation provides adequate throughput for status, configuration, and slow command traffic. Industrial users should add protection suited to the wiring length and environment, since the automotive-compliant LIN interface does not by itself specify every possible industrial surge condition. Keep bus traces short and follow the NXP application-circuit layout.
تجویز کردہ
Seat and Window Control Interface
The TJA1028T/5V0/20:11 fits distributed seat, window, and mirror-control nodes that communicate over LIN while controlling external power stages. Its integrated regulator provides 5.0 V for controller logic, while the LIN interface handles communication with the vehicle's master node. This division of responsibilities allows a compact SO-8 implementation and avoids powering motors from the 70 mA regulator. Include the recommended bus termination and supply-decoupling network, and verify transient performance for the exact electrical environment of the actuator module.
تجویز کردہ
تجویز کردہ پروڈکٹس کا خلاصہ
کے لیے انجینئرنگ ریفرنس ڈیٹا TJA1028T/5V0/20:11 — موازنہ، ڈیزائن رہنمائی، اور تعمیل کی معلومات۔
انتخاب کی گائیڈ
متبادلات کے ساتھ موازنہ
| پیرامیٹر | یہ پروڈکٹ | TJA1028DT | TJA1028T/5V0/20 |
|---|---|---|---|
| Package | SO-8 | SO-8 | SO-8 |
| Brand | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors |
| LIN Bus Speed | 20 kbaud | 20 kbaud | 20 kbaud |
| Integrated Regulator Output | 5.0 V | 5.0 V | 5.0 V |
| Regulator Output Range | 4.9 V to 5.1 V | 4.9 V to 5.1 V | 4.9 V to 5.1 V |
| Regulator Maximum Output Current | 70 mA | 70 mA | 70 mA |
| Propagation Delay Time | 6 us | 6 us | 6 us |
| Compliance | LIN 2.0/2.1, SAE J2602, ISO 17987-4:2016 | LIN 2.0/2.1, SAE J2602, ISO 17987-4:2016 | LIN 2.0/2.1, SAE J2602, ISO 17987-4:2016 |
| Process and Design Status | Original TJA1028 generation | Preferred SOI3+ process with modified die and package bill of materials | Functionally identical generation not recommended for new designs |
اہم امتیازی خصوصیات
- Combines a 20 kbaud LIN interface and regulated local supply in one package (بمقابلہTJA1028T/5V0/20)
- Uses NXP's preferred SOI3+ implementation (بمقابلہTJA1028T/5V0/20:11)
- Combines bus communication with local power conversion (بمقابلہDiscrete LIN transceiver and regulator implementations)
ڈیزائن نوٹس
Treat the integrated 5.0 V regulator as a 70 mA auxiliary supply, not as a general-purpose power rail. Budget the host controller, pull-ups, sensors, and status-indicator logic together against this limit. If the node contains a relay, lamp, motor, or solenoid, use a separate driver and supply. Check the minimum operating supply and regulator dropout conditions in the NXP electrical-characteristics table before adding margin to the 5 V output.
Follow the NXP TJA1028 application circuit for supply decoupling and LIN-bus termination. Place the input and regulator capacitors close to their device pins and keep the LIN trace short and isolated from high-current switching paths. The SO-8 footprint provides limited routing space, so reserve clearances around the bus node and avoid routing motor or relay current beneath the transceiver.
Do not replace the 5.0 V ordering variant with the 3.3 V version without reassessing every load, and do not substitute a 10 kbaud variant where the 20 kbaud network timing is required. Also verify the exact TJA1028 order code, temperature range, and reel configuration before production substitution. The TJA1028DT is functionally identical but uses a modified die and package bill of materials, so review the NXP documentation for any assembly-specific change.
تعمیل کی معلومات
RoHS compliance is identified for TJA1028T. The device supports LIN 2.0/2.1, SAE J2602, and ISO 17987-4:2016 for 12 V systems. AEC-Q100, REACH, lead-free, halogen-free, and conflict-minerals status are not confirmed by the product information available for this order code.